MBL-39M - Blender MPM - Free user manual and instructions
Find the device manual for free MBL-39M MPM in PDF.
User questions about MBL-39M MPM
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Blender in PDF format for free! Find your manual MBL-39M - MPM and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. MBL-39M by MPM.
USER MANUAL MBL-39M MPM
EN We wish you satisfaction from using the product and invite you to check a wide range of other MPM appliances
natural_image
Close-up of a black and white blender with a side panel, no visible text or symbolsMBL-39M
TYCOVY MIXF HSADA
STABMXER-SE
MUENHEJIHOU-3E1
MANUAL ELENDER SET
BATIDORA DE MANO - SEI MIXLUR PLONGLAN | MANUEL K I
KLZIMXLR-KL52LI
TRULA CREAMMERSIONS SET
PANKIN SRASTUKAS - RINKIN'S POKAS B - NIS PIS - KOMPLEKLE
STAAL MIXLH 511
BLENDER BECZNY - ZESTAW
MIXER DE MANA 5
text_image
Labeled diagram of kitchen equipment including blender, stand mixer, and measuring cup
Stainless steel body
Smooth Touch - intuitive smooth speed setting
Stainless steel mixing attachment for use at high temperature
Whaking attachment for eggs white and light sauces
Double-aided blade for slicing and chopping
1250 ml container for chopping and grinding + 700 ml container
BEZPEČNOSTNÍ POKYNY PŘI POUŽÍVÁNÍ
-Read the instructions carefully before use.
-Do not handle the device with wet hands.
-Take special care when children are near the device.
- Do not use the device for purposes other than those for which it was intended.
- Do not immerse the device, cable or charger in water or other liquids.
-Do not let the power cord hang over the edge of the table/counter.
-Do not leave the device unattended during operation.
- Never use a damaged device, including one with a damaged cord or plug, in which case have it repaired at an authorised service centre.
-Do not use the device outdoors.
- Do not hang the power cable on sharp edges or allow it to come into contact with hot surfaces.
-Do not place the device on a hot surface.
- Do not place the device near other electric cookers, burners, ovens, etc.
-The device should be put on a dry, flat and stable surface.
-The device is intended for domestic use only.
Always ensure that all parts of the device are correctly fitted before starting work.
-Use of accessories not recommended by the manufacturer may cause damage to the device, fire or personal injury.
-The device may be used by people with reduced physical, sensory or mental abilities, as well as those without prior knowledge or experience in using such types of device, provided that they either are supervised or have been instructed and informed about potential threats which they fully understood.
-The device must be kept away from children. Keep the device and cable out of the reach of children.
-Children are forbidden to perform cleaning and maintenance activities.
-Children should be supervised to ensure that they do not play with the device.
- Do not pull the plug out of the power socket by pulling the cord.
- The equipment is not designed to operate using external timers or a separate remote control.
-Do not connect the plug to the power socket with wet hands.
-For the safety of children, please do not leave freely accessible parts of the packaging (plastic bags, cardboard boxes, polystyrene, etc.).
-WARNING! Do not allow children to play with the film. Danger of suffocation!
-Check that the power parameters on the device's rating plate correspond to the parameters of your power supply network.
-CAUTION! Before starting cleaning and maintenance works, disconnect the device from the power supply network and wait until it cools down completely after work. Do not submerge the device into water!
-CAUTION! Do not use sharp objects, abrasive polishes, solvents or other strong chemicals for cleaning since their use may cause damages to the device.
-Before the first use, remove all bags, stickers, tapes and transport locks from the device and its accessories.
-Disconnect the device from the power supply each time when the device is left unattended and before any assembling, disassembling, or cleaning works.
- Wait until the motor stops completely before disassembling the device.
- Pay special attention when handling the blades, especially when removing and washing them.
-Do not exceed the maximum capacity indicated on the container.
-Allow hot ingredients to cool down before processing them.
- Clean the device, in particular parts being in direct contact with food, before first use, immediately after finishing work and if the device has not been used for a long time. The procedure is described in details in the “CLEANING AND MAINTENANCE” section.
- Keep your hands away from moving parts when the device is in operation!
-CAUTION! Avoid physical contact with the cutting blades while emptying and cleaning the device as they are very sharp and might cause serious injuries.
DESCRIPTION OF THE APPLIANCE
- Blender housing
- Start button and speed control
- Whipping attachment for egg whites, light creams and sauces
- Stainless steel blending attachment
- Blender container lid
- Lid lock buttons
-
Product feeding opening with a food processor pusher
-
Chopping and grinding knife with a stainless steel blade
- Disc pin
- Full double-sided disc for grinding and cutting vegetables and fruits
- Mixer container with handle, capacity of 1250ml
- 700ml container
BEFORE FIRST USE
- Remove the device from the box, remove all bags, labels, cardboard profiles and fillers. Make sure the device has not been damaged during transport. Contact the seller in case of any doubts.
- Make sure the electrical mains parameters match the technical data on the device's rating plate.
- Carefully wash and dry all elements that contact food, following the recommendation in the "CLEANING & MAINTENANCE" chapter.
BLENDER USE
CAUTION! Do not allow the blender housing (1) to get wet. Prior to the accessories mounting/demounting procedure, make sure the device is not connected to the power supply.
CAUTION! The temperature of food prepared with the blender must not exceed 60°C. CAUTION! The blades' cutting edges are sharp Risk of possible injury! Use with cau-tion!
Mount one of the selected accessories to the blender housing (1): mixing attachment (4), whipping attachment (3) or food processor container (11) with cover (5) along with appropriate accessories mincing and chopping knife (8) or double-sided grinding and cutting disc (10). To lock the accessories, rotate the blender housing (1) relative to the attachment to the left until it locks. Do the opposite for disassembling the attachment. Pay close attention in order to avoid self injuries or parts damages when disconnecting accessories.
The MBL-39M version of the blender is a compact device facilitating everyday meal preparation. The device is especially recommended for grinding raw and cooked vegetables, soft fruits (without seeds), preparing sauces, creams, soups, mixing liquids, etc. Prior to grinding large ingredients with a blender cut them into smaller pieces (1-2 cm).
| Appetizer type | Maximum time of continuous operation |
| Mixing attachment (4) 60 s | |
| Whipping attachment for egg whites, light creams and sauces (3) | 2 min |
| Shredding and chopping kit (knife) (8) 40 s | |
| Set for grinding and cutting (double-sided disc) (10) | 2 min |
CAUTION! After completing one work cycle, turn off the device and wait at least 3 minutes until it cools down.
SHREDDING AND CHOPPING SET (KNIFE) ASSEMBLY
Place the container (11) on a dry and stable surface. Remove the cover (5) from the container (11) by pushing the two lock buttons (6) on the cover outwards. Then put the chopping knife (8) on the pin protruding from the container bottom, and then put the cover on so that the tip of the chopping knife fits the cover. After ensuring that all parts are assembled correctly, insert the blender housing (1) into the mounting socket in the cover by turning it counterclockwise.
GRINDING AND CUTTING SET ASSEMBLY (DOUBLE-SIDED DISC)
Place the container (11) on a dry and stable surface. Remove the cover (5) from the container (11) by pushing the two lock buttons (6) on the cover outwards. Next, attach the tapping pin (9) to the pin protruding from the centre of the bottom of the container, and then attach the pin and the disc (10) (mind the appropriate side, depending on the activity being performed, i.e. abrasion/cutting).
Place the cover so that the tip of the disc (10) fits the cover (5). After ensuring that all parts are assembled correctly, insert the blender housing (1) into the mounting socket in the cover by turning it counterclockwise.
PUSH BUTTON TO START AND ADJUST BLENDER SPEED
Once you have ensured that all components are correctly assembled, connect the appliance plug to the power source.
To start the blender, press the speed control button (2) gently. The appliance will start at low speed. Continuing to press the button (2) increases the speed of the blender. Releasing pressure on the button (2) stops the blender.
CLEANING AND MAINTENANCE
CAUTION! The blades' cutting edges are sharp Risk of possible injury! Use with caution!
- Prior to cleaning, remove the plug from the power socket.
- Before and after each use, disassemble the device's components and wash it thoroughly in warm water with the addition of detergent, then rinse thoroughly and dry.
-
Periodically check parts before reassembling. Do not use the blender if the knives of blender blades (4) are jammed or rotate with difficulty.
-
Never immerse the blender in water. The device should be instead disconnected from the power source and its housing cleaned with a damp cloth.
- If discoloration of plastic elements occurs after rubbing, e.g. carrots, they can be wiped with a cloth and cooking oil.
CAUTION! Do not use sharp objects, abrasive polishes, solvents or other strong chemicals for cleaning since their use may cause damages to the device.
TECHNICAL DATA
| Model MBL-39M | |
| Power supply 220-240V ~ 50/60HZ | |
| Power 1500W | |
| Availability of off or standby mode available | |
| Standby power consumption - | |
| Power consumption in off-mode 0,25W | |
| Power consumption in network standby mode | - |
| Automatically enters standby mode after - | |
| Automatically enters shutdown mode after - | |
| Network standby mode, if the device has the function of connecting to the application | - |
| LED operation indicator showing device activity - | |
| Length of mains cable 1,2m |
CAUTION! MPM agd S.A. reserves the right to technical changes.
Proper disposal of the product (waste electrical and electronic equipment)
Marking on the product indicates that after the service-life of the product expires, it should not be disposed with other type of municipal waste. Used equipment may have a negative impact on the environment and health of people due to potentially containing hazardous substances, mixtures and components. Mixing electric waste with other types of waste or disassembling those in an unprofessional manner may cause a release of substances that are hazardous to the environment and health.
Used equipment should be handed-over to a point for collection of electric waste. In order to obtain detailed information regarding the electric waste collection points, the user should contact the municipal point of electric waste collection or used equipment processing department.
