D215831 - Drill DEWALT - Free user manual and instructions

USER MANUAL D215831 DEWALT

You have chosen a DEWALT tool. Years of experience, thorough product development and innovation make DEWALT one of the most reliable partners for professional power tool users.

Technical data

D215831

Column length mm 995

Collar diameter mm 60

Max. drill diameter with water collector mm 152 without water collector mm 172

Inclination 0 - 45°

Weight kg 16

The following symbols are used throughout this manual:

Denotes risk of personal injury, loss of life or damage to the tool in case of non-observation of the instructions in this manual.

Manufacturer's declaration

D215831

DeWALT declares that this unit has been designed in compliance with 98/37/EC.

This unit must not be put into service until it was established that the Power Tool to be connected to this unit is in compliance with 98/37/EC (identified by the CE-marking on the Power Tool).

Director Engineering and Product Development Horst Großmann

Observe the safety regulations in the instruction manual of the Power Tool to be connected to this attachment. Also observe any applicable additional safety rules. Read the following safety instructions before attempting to operate this product.

Keep these instructions in a safe place!

General

1 Keep work area clean

Cluttered areas and benches can cause accidents.

2 Keep children away

Do not let children come into contact with the tool or its attachments. Keep all people away from the work area.

3 Dress properly

Do not wear loose clothing or jewellery.

They can be caught in moving parts. Preferably wear rubber gloves and non-slip footwear when working outdoors. Wear protective hair covering to keep long hair out of the way.

4 Wear safety goggles

Also use a face or dust mask in case the operations produce dust or flying particles.

5 Beware of maximum sound pressure

Take appropriate measures for the protection of hearing if the sound pressure of 85 dB(A) is exceeded.

6 Stay alert

Watch what you are doing. Use common sense. Do not operate the tool when you are tired.

7 Use appropriate tool

The intended use is laid down in this instruction manual. Do not force small tools or attachments to do the job of a heavy-duty tool. The tool will do the job better and safer at the rate for which it was intended. Warning! The use of any accessory or attachment or performance of any operation with this tool, other than those recommended in this instruction manual may present a risk of personal injury.

8 Have your Power Tool Attachment repaired by an authorized DeWALT repair agent

Repair of your Power Tool Attachment being a matter of precision and skill, always take it to your DEWALT Authorized Repair Agent.

Package contents

The package contains:

1 Drill stand
1 Feed handle
1 Allen key, 6 mm
1 Allen key, 8 mm
1 Instruction manual
1 Exploded drawing

• Check for damage to the tool, parts or accessories which may have occurred during transport.
• Take the time to thoroughly read and understand this manual prior to operation.

Description (fig. A1 & A2)

Your D215831 drill stand has been designed to extend the capabilities of your DEWALT diamond drilling machine. The stand enables set up in both vertical and horizontal applications. Establishing angles ranging from 0 to 45^ , the stand can also be used in slope applications.

The drill stand is suitable for use with the following DEWALT models: D21580K/D21582K/D21583K, or with any other diamond drill with a 60 or 53mm collar.

Fig.A1

1 Carriage
2 Carriage lock
3 Transport handle
4 Feed handle
5 Drill holder
6 Column
7 Angle drilling scale
8 Angle adjustment lever
9 Base
10 Wheels
11 Air level for vertical applications
12 Air level for horizontal applications
13 Friction knob
14 Drilling depth scale
15 Stabilizer bolts
16 Hose connection

Optional accessories (fig. A2)

Consult your dealer for further information on the appropriate accessories.

17 D215834 Reduction ring
18 D215825 Fastening set for concrete
19 D215826 Fastening set for masonry
20 D215827 Spare dowel for concrete (10 pcs)
21 D215828 Spare dowel for masonry
22 D215837 Vacuum pump
23 D215839 Vacuum kit
24 D215835 Bracing bracket
25 D215832 Water collection ring
26 D215833 Spare seal for water collection ring (10 pcs)

Assembly and adjustment

Also refer to your drill manual.

Mounting the drill (fig. B)

• Remove the side handle from the machine.
• Loosen the bolt (31) using the feed handle (4).

• Mount the machine to the stand.

• For machines with a 60~mm collar: the machine can be mounted directly to the stand.

• For machines with a 53 mm collar: The D215834 reduction ring is required to make the collar of the drill fit in the drill holder.

• Tighten the bolt (31) using the feed handle (4).

Always mount your drill firmly to prevent movement.

Installing the stand (fig. C - G)

The stand can be installed either vertically (fig. C) or horizontally (fig. D) on a surface such as a floor or a wall.

Always make sure the stand is securely fastened on the surface.

Mounting the stand with the fastening set (fig. E1 & E2)

A fastening set is required to secure the stand to masonry (fig. E1) or concrete (fig. E2) surfaces.

• Locate the stand at the desired position and mark the location of the mounting hole on the wall.
• Drill a hole at the marked location.
• In concrete: 15 mm diameter by 55 mm deep

• In masonry: 20 mm diameter by 85 mm deep

• Insert the anchor plug (32) into the hole.

• Tighten the anchor (33) into the anchor plug.
• Position the stand over the anchor.
• Place a washer (34) and wingnut (35) onto the bolt. Securely tighten the wingnut.

Mounting the stand with the bracing bracket (fig. F)

For a quick set up in indoor applications, a bracing bracket can be used to secure the stand.

• Position the stand.
• Place the bracket foot (36) against the base (9).
• Move the latch (37) out of the way to depress the lever (38). Extend the bracket (24) until it reaches the opposite surface. Release the lever.
• Clamp the bracket in position using the rod (39).
• Insert the pin (40) into the hole closest to the clamping mechanism.

Mounting the stand with the vacuum pump (fig. G1 & G2)

If the stand is to be mounted to delicate surfaces, a vacuum pump can be used to secure the stand. The vacuum created in the base keeps the stand securely in position.

This application works only if the stand is mounted to a flat surface (e.g. tile, vibrated concrete) which is clean and free of debris and swarf. Otherwise, the suction may drop, causing the stand to fall or move.

• Fit the rubber seal (41) in the slot (42) in the underside of the base.
• Place the vacuum handle (43) over the opening in the base (9).
• Tighten the screw (44) with the washer (45) into the handle.
• Position the stand.
• Connect the hose of the vacuum pump to the connection point (16).
• Switch on the vacuum pump. Keep the pump switched on as long as the application requires.

Adjusting the stand (fig. A)

• Read one of the air levels to check whether the stand is level.

• Air level (11) for vertical applications

• Air level (12) for horizontal applications
• If adjustment is required, proceed as follows:
• Turn the stabilizer bolts (15) one by one until the stand is level

Mounting the water collection ring (fig. H)

If the stand is used in wet drilling applications, a water collection ring can be mounted to ensure a proper discharge of water.

• Loosen the bolts (46) a few turns.
• Hold the water collection ring (26) in front of the base (9).
• Slide the recessed ends of the mounting bracket (47) in the space created between the bolts and the base.
• Check that the assembly aligns with the accessory fitted.
• Securely tighten the bolts.

Adjusting the drill angle (fig. 1)

The column can be tilted to facilitate slope drilling applications. The scale (7) represents angles up to 45^ .

• Remove the locking bolt (48) and store it in a safe place.
• Loosen the angle adjustment lever (8).
• Tilt the column at the handle (3).
• Align the top of the lever base with the required angle (see indication X).
• Tighten the angle adjustment lever.
• After use, restore the stand in straight-up position and replace the locking bolt.

Fitting the feed handle (fig. J)

The quick-release feed handle (4) can be mounted in one simple operation both to the left and the right of the stand.

• Align the locating rod in the feed handle with the slot in the shaft (49).
• Push the handle onto the shaft.

Adjusting the friction (fig. A)

The friction knob (13) is used to increase or decrease the friction of the carriage mechanism.

• Turn the knob clockwise to increase the friction.
• Turn the knob counterclockwise to decrease the friction.

Instructions for use

Always observe the safety instructions and applicable regulations.

Refer to your drill manual.

Prior to operation:

• Make sure the stand is fastened securely.
• Mount the appropriate accessory.
• Check the friction on the carriage.
• Mark the spot where the hole is to be drilled.

Unlocking the carriage (fig. K)

• To unlock the carriage (1) pull out the lock knob (2).
• To lock the carriage move the carriage until the locking shaft passes the hole (50) in the column and jumps into place.

Always lock the carriage when the assembly is not in use.

General tips for drilling with diamond core bits

llow the core bit or manufacturer's recommendations for using the accessory.

Note: The use of a centredrill is not necessary.

• Take hold of the feed handle.
• Unlock the carriage.
• Switch on the drill motor in continuous mode.
• Slowly feed the accessory into the workpiece using the feed handle.
• At the start of the cut, apply light pressure to allow the accessory to perform the initial groove.
• Continue applying sufficient pressure to achieve a smooth progressive cut. Do not force.
• Take extra care when the accessory is about to break through the surface to prevent splintering.
• Always switch off the tool when work is finished and before unplugging.
• After use move the carriage upwards until the carriage locks into place.

Transporting (fig. A1)

The wheels (10) have been provided to facilitate transportation.

• Transport the assembly using the carrying handle (3).

Always transport the stand with the carriage locked.

Maintenance

Your attachment has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and regular cleaning.

Adjusting the carriage (fig. L)

After repeated use, the carriage may become loose. To adjust the play, proceed as follows:

• Tighten the bolts (51) as necessary.
• Check the up and down movement of the carriage.

Clearing the feed travel (fig. L)

The feed travel should be cleared periodically to ensure smooth operation.

• Raise the carriage to the highest position possible.
• Clear the gear rack (52) using a soft brush or dry cloth.

Lubrication

Your attachment requires no additional lubrication.

Protecting the environment

Separate collection. This product must not be disposed of with normal household waste.

Should you find one day that your DEWALT product needs replacement, or if it is of no further use to you, do not dispose of it with household waste. Make this product available for separate collection.

parate collection of used products and packaging allows materials to be recycled and used again.

Re-use of recycled materials helps prevent environmental pollution and reduces the demand for raw materials.

Local regulations may provide for separate collection of electrical products from the household, at municipal waste sites or by the retailer when you purchase a new product.

DeWALT provides a facility for the collection and recycling of DeWALT products once they have reached the end of their working life. To take advantage of this service please return your product to any authorised repair agent who will collect them on our behalf.

You can check the location of your nearest authorised repair agent by contacting your local DeWALT office at the address indicated in this manual. Alternatively, a list of authorised DeWALT repair agents and full details of our after-sales service and contacts are available on the Internet at: www.2helpU.com

GUARANTEE

• 30 DAY NO RISK SATISFACTION GUARANTEE If you are not completely satisfied with the performance of your DeWALT tool, simply return it within 30 days, complete as purchased, to the point of purchase, for a full refund or exchange. Proof of purchase must be produced.

- ONE YEAR FREE SERVICE CONTRACT

If you need maintenance or service for your DeWALT tool, in the 12 months following purchase, it will be undertaken free of charge at an authorized DeWALT repair agent. Proof of purchase must be produced. Includes labour and spare parts for the attachments. Excludes accessories.

- ONE YEAR FULL WARRANTY

If your DeWALT product becomes defective due to faulty materials or workmanship within 12 months from the date of purchase, we guarantee to replace all defective parts free of charge or, at our discretion, replace the unit free of charge provided that:

The product has not been misused.
- Repairs have not been attempted by unauthorized persons.
- Proof of purchase date is produced. This guarantee is offered as an extra benefit and is additional to consumers statutory rights.

For the location of your nearest authorized DEWALT repair agent, please use the appropriate telephone number on the back of this manual. Alternatively, a list of authorized DEWALT repair agents and full details on our after-sales service are available on the Internet at www.2helpU.com.

SOPORTE DE TALADRO

D215831

jEnhorabuena!

Caracteristicas techniques

Director Engineering and Product Development Horst Großmann

L'emballage contient:

Director Engineering and Product Development Horst Großmann

DEWALT, Richard-Klinger-Straße 11, D-65510, Idstein, Duitsland

Director Engineering and Product Development Horst Großmann

DEWALT, Richard-Klinger-Straße 11, D-65510, Idstein, Tyskland

Sikkerhetsforskrifter

1 ARS FRI VEDLIKEHOLDSERVICE

Director Engineering and Product Development Horst Großmann

Director Engineering and Product Development Horst Großmann

Director Engineering and Product Development Horst Großmann

DEWALT, Richard-Klinger-Straße 11, D-65510, Idstein, Tyskland

Sakerhetsinstruktioner

ETeio n EIOKEun Twv EapntuTuw TwV

ηλEKPTPIKωv εpyαεiων απaTei ακρβεia kai

Eouoiodotnveo uvepyeio EIOKuwv BwALT.

ELevXoc Tou Tepiexou Tns oukeuaia