CMS 803DC BM - Speaker TANNOY - Free user manual and instructions

USER MANUAL CMS 803DC BM TANNOY

Close-up of two white ceramic speakers with visible inner and outer rings, no text or symbols present.

CMS 3.0 Series

CMS803DC BM/PI/Q / CMS803 PI BACKCAN

8" Full Range Ceiling Loudspeaker with Dual Concentric Driver

CMS603DC BM/PI / CMS603ICT BM/PI/LS / CMS603 PI BACKCAN

6" Full Range Ceiling Loudspeaker with Dual Concentric or ICT Driver

CMS503DC BM/PI/LP / CMS503ICT BM/PI/LP / CMS503 PI BACKCAN

5" Full Range Ceiling Loudspeaker with Dual Concentric or ICT Driver

CMS403DCE / CMS403ICTE

4" Full Range Ceiling Loudspeaker with Dual Concentric or ICT Driver and adjustable "eyeball" design

2 CMS 3.0 Series Quick Start Guide 3

EN

Safety Instruction

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Followal instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings, install in

accordance with the manufacturer's instructions

1. Do not install near any heat sources such

including well here! that produces heat.

1. Use only attachments/acrossories specified

by the manufacturer.

ES

FR

DE

PT

IT

1. Use only with

the cart, stand, tripod,

to the magnitude of

with the sum

When a cart is used.

use caution when moving

the cart/apparatus

combination to avoid injury from tip-over.

1. Correct disposal of this

product: This symbol indicates that

this product must not be disposed

of with household waste,

according to the NEE Effective

(2012.13.20, and your instructions) Buy: This product should be taken

to a collection center flexed for

the recycling of waste electrical and electronic equipment (EE). The mishandling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the efficient use of natural resources. For more information about where you can take your waste equipment for recycling, please contact your local city office, or your household waste collection service.

1. Do not install in a confined space, such as a

book case or similar unit.

1. Do not place naked flame sources, such as lighted

candles, on the apparatus.

tripede, support of MPa

in Mghthials while My

generalment available at 15, Equipments

Hambits abfillan as antecapsen

indicate the question represented in

m = 311

PT

IT

4 CVS 3.0 Series Quick Start Guide 5

HL Belangrijke

houseprice 3.041 mag upgrades 2) product market

Thank you for purchasing this Tannoy Ceiling Monitor System product. Designed for both speech and music program material, the Tannoy CMS range provides exceptional sonic quality and long-term reliability in all ceiling mount applications. The CNS 3.0 DC series features new 16 ohm Dual Concentric drivers for improved performance and prolonged service life.

Unpacking

Every Tannoy product is carefully inspected before shipment. After unpacking, please inspect your product to ensure no damage has occurred in transit. In the unlikely event of damage, please notify your dealer and retain all shipping materials as your dealer may require return shipment.

All CMS loudspeakers are shipped in pairs and provided with the following accessories as standard: C-ring, tile-bridge kit, cut-out template and paint mask. A plaster (mud) ring is available as an optional accessory.

Safety Notices

Some regional construction codes require the use of a secondary method of securing loudspeakers in the ceiling to provide security of a backup support. A secondary support line should be attached from the safety loop on the rear of the product to a source point on the ceiling. For PI models, the secondary support line should be attached from the back of the driver chassis to a source point on the ceiling. Please consult the relevant construction codes in your region.

When using a power driver to install the product, it is essential to use the correct torque level settings to avoid over-tightening and damage to the ceiling material or clamps. Recommended torque setting: 1.5 Nm

Tannoy will not be held responsible for any damages caused by the improper installation of these loudspeakers.

The CMS 603 ICT LS is UL-1480, category UUMW, for use with non-DC supervised systems.

Electrical Safety Notice: To comply with the standard IL-1480, metal-clad flexible conduit (5K) is required for connection to the terminal block for proper earth grounding.

In order to comply with UL regulations, the PI backcan must always be used with the CMS PI models.

SHE

In addition, the following is a 100% 1980. It is required to be a result of the actual call and given cost, which is not considered in the coming year. So it is not possible, there will be no change in the amount of cash or cash equivalents for the period of the year.

Product Feature Identification

IMPORTANT NOTE: Drawings for each loudspeaker below are generic and apply to the loudspeaker types specified. Some variations will be apparent in some models, but differences are not critical for installation purposes except as noted.

Blind Mount

The blind-mount models are supplied with a pre-fitted backcan. Above applies to all models as well any others that do NOT have a "PI" suffix.

Pre-install

Two technical illustrations of mechanical components, one showing a circular housing and the other a 3D architectural model (no text or symbols visible)

A pre-install (PI) unit is shown without the optional pre-install backcan.

Pre-install backcan

Two 3D mechanical components with internal cavities and mounting holes, shown from different angles (no text or symbols visible)

Optional pre-install (PI) backcan for PI models.

NOTE: The CMS 603DC / ICT PI and CMS 803DC models have the transformer pre-attached to the inside of the backcan. The CMS 503DC / ICT PI has the transformer pre-attached to the loudspeaker assembly.

8 CVS 3.0 Series Quick Start Cuke 9

Accessories

Standard Accessories

C Ring Tile bridge hib None & the bridge kit must always be used when installing site separated cooling tiers Color TANNOX CMS 603 Installation Template Cut-out template Paint Mask TANNOX CMS 603 Paint Mask

Optional Accessories

Installation Guide for Suspended Ceilings

1. Remove the ceiling tile from its frame and place it on a flat surface. Position the cutout template (self adhesive backed) on the tile. (Fig.1)
2. Cut out the hole in the ceiling tie using a pad saw following the broken line indicated on the template (Fig.2)
3. Place the C-Ring and tile-bridge on top of the ceiling panel, aligning the C-Ring over the hole, and screw the C-Ring to the tile bridge using the fixings provided. (Fig. 3)

4. Go to the 'Niring and Setting Up' chapter.

5. Slide the speaker assembly through the hole. Turn the screws (denoted "Screw Fix") clockwise on the front of the speaker to extend the mounting wings. Tighten the screws until a firm grip is achieved. (NOTE: Screws have a Poziziv head; use of a Poziziv driver is recommended). If using a power driver, Tannoy recommends a torque setting of 1.3 Km. (Fig.4) DO NOT OVERTIGHTEN!

6. Attach the nylon safety to the hooks on the front taffle before attaching the gille by presenting it to the speakers and allowing the magnets to pull it into position (Fig.5). (With the CMS 403DCelCTe, the gille is already fitted to the product.)

NOTE ON INSTALLATION OF CMS 403DCe/ICTe:

Before tightening the screws in step 5, swivel the speaker in the desired direction. When the screws are tightened, the speaker will lock into position. Replace the front trim to conceal the mounting screws.

10 CMS 3.0 Series

Installation Guide for Sheetrock (Plasterboard) Ceilings

1. Position the cutout template (self adhesive backed) on the ceiling. (Fig.1)
2. Cut out the hole in the ceiling using a pad saw following the broken line indicated on the template then slide the C-ring into the ceiling, aligning it over the cut-out hole. (Fig.2)
3. Go to the 'Wiring and Setting Up' chapter, then return to point 4 below.
4. Slide the speaker assembly through the holo. Turn the screws (denoted "Screw Fix") clockwise on the front of the speaker to extend the mounting wings. Tighten the screws until a form grip is achieved. [NOTE: Screws have a PazDriv head; use of a PazDriv driver is recommended]. If using a power driver, Tamnoy recommends a torque setting of 1.5 Nm. (Fig.3) DO NOT OVERTIGHTEN!
5. Attach the nylon safety to the hooks on the front table before attaching the grille by presenting it to the speakers and allowing the magnets to pull it into position (Fig.4). (With the CVS-403DCe/ICTe, the grille is already fitted to the product.)

NOTE ON INSTALLATION OF CMS 403DCe/ICTe:

Before tightening the screws in step-1, stivel the speaker in the desired direction. When the screws are tightened, the speaker will lock into position. Replace the front trim to conceal the mounting screws.

Fig.1

[5]

19.1

184

Installation Guide for Optional Plaster Ring

Quick Star Guide 11

EN

An optional plaster (mud) ring bracket is available from Tannoy. This bracket is designed to be pre-installed into newly constructed, non-suspended ceilings.

1. Nail or screw the plaster ring to the joints. (Fig. 1)

2. Lay the speaker wiring to where the speaker will be fitted and complete the plastering work on the ceiling. (Fig.2)

3. Go to the 'Wiring and Setting Up' chapter, then return to point 4 below.

4. Slide the speaker assembly through the hole. Turn the screws (denoted "Screw Fox") clockwise on the front of the speaker to extend the mounting wings. Tighten the screws until a firm grip is achieved. (Note: Screws have a PoziDriv head; use of a PoziDriv driver is recommended). If using a power driver, Tamney recommends a torque setting of 1.5 Km. (Fig.3)

DO NOT OVERTIGHTEN!

1. Attach the nylon safety to the hooks on the front baffle before attaching the grille by presenting it to the speakers and allowing the magnets to pull it into position (Fig.4). With the CMS 4030Co/CTe, the grille is already fitted to the product.)

Hg

Fig.2

B(3

FLL4

NOTE ON INSTALLATION OF CMS 403DCE/ICTe:

Before tightening the screws in step 4, swivel the speaker in the desired direction. When the screws are tightened, the speaker will lock into position. Replace the front trim to conceal the mounting screws.

12 CVS 3.0 Series Quick Start Juice 13

Installation Guide for Optional Pre-Installation Backcan (PI Models Only)

An optional pre-install backcan is available for all pre-install (PI) models. The backcan is designed for pre-installation in newly constructed, non-suspended ceilings. NOTE: The CMS 603DC/CT and CMS RHDC models have the transformer pre-attached to the inside of the backcan; the CMS 503DC/CT models have the transformer pre-attached to the loudspeaker assembly.

1. Attach the backcan to a safe and secure fixing point. This can be done in a number of ways. METHOD 1: Fix the backcan to a secure fixing point by using suitable fixings with the 4 fixing holes provided on the PI backcan. (Fig.1)

METHOD 2: Secure the backcan to a safe and secure fixing point using suitable fixings with the flexible straps that are attached to the P1 backcan. (Fig.2)

METHOD 3:

a. Attach the PI backcan to the optional pre-mount ring (plaster ring) using the fixings provided with the pre-mount ring. (Fig.3)

b. Next, secure the wings of the pre-mount ring to a safe and secure fixing point by using suitable fixings. (Fig.4)

Please turn over

1

F42

131

F44

Installation Guide for Optional Pre-Installation Backcan (PI Models Only)

1. Attach the conduit to the installed backcan. This can be done in two ways:

METHOD 1: You can use the clamp at the back of the pre-install backcan. The product will accept a squeeze connector with a thread size of up to 22 mm. To remove the cable clamp, simply uncrew the threaded washer (under the wiring cover) which holds the cable clamp in place and replace it with a conduit squeeze connector. (Fig.5)

METHOD 2: You can use any of the three knock-out points at the sides of the PI backcan (19 mm, 22 mm or 28 mm diameter). (Fig.6)

1. If conduit is not chosen as the wiring method, run an approved speaker cable to the installed can. Terminate in the top mounted cable clamp or with an approved cable connector in one of the three knock-out points at the sides of the PI backcar.

2. Cut hole in the proper location in the ceiling using a pad saw. Place the pre-install backcan over the hole. (Fig.7)

1. Go to the 'Wiring and Setting Up' chapter, then return to point 6 below.

2. Side the speaker assembly through the note. Turn the screws (denoted "Screw Fix") clockwise on the front of the speaker to extend the mounting wings. Tighten the screws until a form grip is achieved. NOTE: Screws have a PostDrive head; use of a PostDrive driver is recommended). If using a power driver, Tammy recommends a torque setting of 1.5 Nm. (Fig. 8) DO NOT OVERTIGHTEN!

3. Attach the nylon safety to the hooks on the front baffle before attaching the grille by presenting it to the speakers and allowing the magnets to pull it into position. (Fig.9)

增

Fig.5

Wiring and Setting Up

1. Open the wiring cover (if applicable) and locate the Euro-type connector plug and socket at the back of the speaker. [Fig.1]

2. For connection to an amplifier, use Pins 1 and 2 (Fig.2):

• Fin 1 is positive

- Pin 2 is negative

For connection to additional speakers in a distributed line, Pins 3 and 4 are in parallel where: • Pin 3 is negative

- Pin 4 is positive

1. Close the wiring cover and tighten both screws on the cable clamp (if applicable).

2. Use the rotary switch on the front of the unit to select low impedance (Lo2) mode or high impedance (70 V or 100 V) for distributed applications.

THE SPEAKER IS SUPPLIED IN LOW IMPEDANCE MODE. NEVER CONNECT THE SPEAKER TO A 70/100 VOLT AMPLIFIER WHILE IT IS SET FOR LOW IMPEDANCE.

CMS 403DCe/ICTe and CMS 503DC/ICT models (all variants) use a 30 W transformer. In distributed line applications, the transformer can be tapped at 30 W, 15 W and 7.5 W, with an additional 3.75 W tap for 70 V line systems. [Fig.3]

CMS 603DC/CT and CMS 803DC models (all variants) use a 60 W transformer. In distributed line applications, the transformer can be tapped at 60 W, 30 W and 15 W, with an additional 7.5 W tap for 70 V line systems. (Fig.4)

Quick Star Guide

Fig.1

1027

(b).

Fig.1

Painting

If desired, the grille and baffle panel may be painted to match the surrounding décor.

Painting the baffle:

- Carefully mask off the driver assembly using the paint mask provided to ensure that the paint does not come into contact with the cone and roll surround.

- Apply several thin coats of paint – this will provide a better finish than one overly thick coat.

Painting the grille:

• Carefully remove the acoustically transparent grille cloth from the reverse side of the grille.
• Paint the grille and then replace the grille cloth - several thin coats of paint will provide a better finish than one overly thick coat.
• Re-bond the grille cloth to the grille over the entire area using a light spray-adhesive to avoid audible resonances.

Introducción

The bridge kit Note: A bit bridge kit must always be used when mounting into supervised ceiling tiles TANNOY CMS 603 Installation Template Cut-out temperature

In terms of the cost of the cost of the cost of the cost of the cost of the cost of the cost of the cost of the cost of the cost of the cost of the cost of the cost of the cost of the cost of the cost of the cost of the cost of the cost of the cost of the cost of the cost of the cost of the cost of the cost of the cost of the cost of the cost of the cost of the cost of the cost of the cost of the cost of the cost

• 1 x broken out positive

3D rendering of a cylindrical mechanical component with mounting holes and a small labeled component (no visible text or symbols)

The bridge kit Note: As the bridge kit must always be used when needing into supervised scaling tiles TANNOY CMS 603 Installation Template Cust-to-encence

Optionales Zubehör

In the case of the first, we are not a particular case in the case 5.0003. The case is not a particular case in the case 1.0004. This case is not a particular case in the case 2.0005. The case is not a particular case in the case 3.0006.

Pré-instalar backcan

3D rendering of a cylindrical industrial device with mounting flanges and a central hub (no visible text or symbols)

For the best work, the best job created in 1980, the best job created in 1981, the best job created in 1982, the best job created in 1983, the best job created in 1984, the best job created in 1985, the best job created in 1986, the best job created in 1987, the best job created in 1988, the best job created in 1989, the best job created in 1990, the best job created in 1991, the best job created in 1992, the best job created in 1993, the best job created in 1994, the best job created in 1995, the best job created in 1996, the best job created in 1997, the best job created in 1998, the best job created in 1999, the best job created in 2000, the best job created in 2001, the best job created in 2002, the best job created in 2003, the best job created in 2004, the best job created in 2005, the best job created in 2006, the best job created in 2007, the best job created in 2008, the best job created in 2009, the best job created in 2010, the best job created in 2011, the best job created in 2012, the best job created in 2013, the best job created in 2014, the best job created in 2015, the best job created in 2016, the best job created in 2017, the best job created in 2018, the best job created in 2019, the best job created in 2020, the best job created in 2021, the best job created in 2022, the best job created in 2023, the best job created in 2024, the best job created in 2025, the best job created in 2026, the best job created in 2027, the best job created in 2028, the best job created in 2029, the best job created in 2030, the best job created in 2031, the best job created in 2032, the best job created in 2033, the best job created in 2034, the best job created in 2035, the best job created in 2036, the best job created in 2037, the best job created in 2038, the best job created in 2039, the best job created in 2040, the best job created in 2041, the best job created in 2042, the best job created in 2043, the best job created in 2044, the best job created in 2045, the best job created in 2046, the best job created in 2047, the best job created in 2048, the best job created in 2049, the best job created in 2050, the best job created in 2051, the best job created in 2052, the best job created in 2053, the best job created in 2054, the best job created in 2055, the best job created in 2056, the best job created in 2057, the best job created in 2058, the best job created in 2059, the best job created in 2060, the best job created in 2061, the best job created in 2062, the best job created in 2063, the best job created in 2064, the best job created in 2065, the best job created in 2066, the best job created in 2067, the best job created in 2068, the best job created in 2069, the best job created in 2070, the best job created in 2071, the best job created in 2072, the best job created in 2073, the best job created in 2074, the best job created in 2075, the best job created in 2076, the best job created in 2077, the best job created in 2078, the best job created in 2079, the best job created in 2080, the best job created in 2081, the best job created in 2082, the best job created in 2083, the best job created in 2084, the best job created in 2085, the best job created in 2086, the best job created in 2087, and

The following table provides the data for the year 2018 (25338). The results are obtained from the annual and annual estimates of the year 2017. The results are derived from the annual estimate of the year 2016. The results are obtained from the annual estimate of the year 2015.

3D rendering of a cylindrical mechanical component with mounting holes and a small labeled component (no visible text or symbols)

The bridge kit Note: A bit bridge kit must always be used when mounting into supervised ceiling tiles TANNOY CMS 603 Installation Template Cut-out temperature

Valfria Tillbehör

Thank you for purchasing this Tannoy Ceiling Monitor System product. Designed for both speech and music program material, the Tannoy CMS range provides exceptional sonic quality and long-term reliability in all ceiling mount applications. The CMS 3.0 DC series features new 16 ohm Dual Concentric drivers for improved performance and prolonged service life.

Unpacking

Every Tannoy product is carefully inspected before shipment. After unpacking, please inspect your product to ensure no damage has occurred in transit. In the unlikely event of damage, please notify your dealer and retain all shipping materials as your dealer may require return shipment.

All CMS loudspeakers are shipped in pairs and provided with the following accessories as standard: C-ring, tile-bridge kit, cut-out template and paint mask. A plaster (mud) ring is available as an optional accessory.

Safety Notices

Some regional construction codes require the use of a secondary method of securing loudspeakers in the ceiling to provide security of a backup support. A secondary support line should be attached from the safety loop on the rear of the product to a source point on the ceiling. For PI models, the secondary support line should be attached from the back of the driver chassis to a source point on the ceiling. Please consult the relevant construction codes in your region.

When using a power driver to install the product, it is essential to use the correct torque level settings to avoid over-tightening and damage to the ceiling material or clamps. Recommended torque setting: 1.5 Nm

Tannoy will not be held responsible for any damages caused by the improper installation of these loudspeakers.

The CMS 603 ICT LS is UL-1480, category UUMW, for use with non-DC supervised systems.

Electrical Safety Notice: To comply with the standard IL-1480, metal-clad flexible conduit (BK) is required for connection to the terminal block for proper earth grounding.

In order to comply with UL regulations, the PI backcan must always be used with the CMS PI models.

[Unreadable]

In addition, the following is a 100% of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total

Product Feature Identification

IMPORTANT NOTE: Drawings for each loudspeaker below are generic and apply to the loudspeaker types specified. Some variations will be apparent in some models, but differences are not critical for installation purposes except as noted.

Blind Mount

The blind-mount models are supplied with a pre-fitted backcan. Above applies to all models as well any others that do NOT have a "PI" suffix.

Pre-install

Two technical illustrations of mechanical components, one showing a circular housing and the other a 3D architectural model (no text or symbols visible)

A pre-install [PI] unit is shown without the optional pre-install backcan.

Pre-install backcan

Two 3D mechanical components with internal cavities and mounting holes, shown from different angles (no text or symbols visible)

Optional pre-install (PI) backcan for PI models.

NOTE: The CMS 603DC / ICT PI and CMS 803DC models have the transformer pre-attached to the inside of the backcan. The CMS 503DC / ICT PI has the transformer pre-attached to the loudspeaker assembly.

96 CMS3.0 Series

Accessories

Standard Accessories

Optional Accessories

Installation Guide for Suspended Ceilings

1. Remove the ceiling tile from its frame and place it on a flat surface. Position the cutout template (self adhesive backed) on the tile. (Fig.1)
2. Cut out the hole in the ceiling tie using a pad saw following the broken line indicated on the template (Fig.2)
3. Place the C-Ring and tile-bridge on top of the ceiling panel, aligning the C-Ring over the hole, and screw the C-Ring to the tile bridge using the fixings provided. (Fig. 3)

4. Go to the 'Wiring and Setting Up' chapter.

5. Slide the speaker assembly through the hole. Turn the screws (denoted "Screw Fox") clockwise on the front of the speaker to extend the mounting wings. Tighten the screws until a firm grip is achieved. (NOTE: Screws have a Poziziv head; use of a Poziziv driver is recommended). If using a power driver, Tannoy recommends a torque setting of 1.3 Km. (Fig.4) DO NOT OVERTIGHTEN!

6. Attach the nylon safety to the hooks on the front taffle before attaching the gille by presenting it to the speakers and allowing the magnets to pull it into position (Fig.5). (With the CMS 403DCelCTe, the gille is already fitted to the product.)

Quick Star Guide

Hg!

log?

Fig.3

18.4

Fig.2

NOTE ON INSTALLATION OF CMS 403DCe/ICTe:

Before tightening the screws in step 5, swivel the speaker in the desired direction. When the screws are tightened, the speaker will lock into position. Replace the front trim to conceal the mounting screws.

98 CMS3.0 Series

Quick Steel Guide 99

Installation Guide for Sheetrock (Plasterboard) Ceilings

1. Position the cutout template (self adhesive backed) on the ceiling. (Fig.1)
2. Cut out the hole in the ceiling using a pad saw following the broken line indicated on the template then slide the C-ring into the ceiling, aligning it over the cut-out hole. (Fig.2)
3. Go to the 'Wiring and Setting Up' chapter, then return to point 4 below.
4. Slide the speaker assembly through the holo. Turn the screws (denoted "Screw Fix") clockwise on the front of the speaker to extend the mounting wings. Tighten the screws until a form grip is achieved. [NOTE: Screws have a PazDriv head; use of a PazDriv driver is recommended]. If using a power driver, Tannoy recommends a torque setting of 1.5 Nm. (Fig.3) DO NOT OVERTIGHTEN!
5. Attach the nylon safety to the hooks on the front table before attaching the grille by presenting it to the speakers and allowing the magnets to pull it into position (Fig.4). (With the CMS-403DCe/ICTe, the grille is already fitted to the product.)

Fig.1

[5]

19.1

184

NOTE ON INSTALLATION OF CMS 403DCe/ICTe:

Before tightening the screws in step 4, trigger the speaker in the desired direction. When the screws are tightened, the speaker will lock into position. Replace the front trim to conceal the mounting screws.

Installation Guide for Optional Plaster Ring

An optional plaster (mud) ring bracket is available from Tannoy. This bracket is designed to be pre-installed into newly constructed, non-suspended ceilings.

1. Nail or screw the plaster ring to the joints. (Fig. 1)
2. Lay the speaker wiring to where the speaker will be fitted and complete the plastering work on the ceiling. (Fig.2)
3. Go to the 'Wiring and Setting Up' chapter, then return to point 4 below.
4. Slide the speaker assembly through the hole. Turn the screws (denoted "Screw Fox") clockwise on the front of the speaker to extend the mounting wings. Tighten the screws until a firm grip is achieved. (Note: Screws have a PoziDriv head; use of a PoziDriv driver is recommended). If using a power driver, Tamney recommends a torque setting of 1.5 Km. (Fig.3)
   DO NOT OVERTIGHTEN!
5. Attach the nylon safety to the hooks on the front baffle before attaching the grille by presenting it to the speakers and allowing the magnets to pull it into position (Fig.4). With the CMS 4030Co/CTe, the grille is already fitted to the product.)

Hg

Fig.2

B(3

FLL4

NOTE ON INSTALLATION OF CMS 403Dc/ICTe:

Before tightening the screws in step 4, swivel the speaker in the desired direction. When the screws are tightened, the speaker will lock into position. Replace the front trim to conceal the mounting screws.

100 CMS 3.0 Series Quick Start Guide 101

Installation Guide for Optional Pre-Installation Backcan (PI Models Only)

An optional pre-install backcan is available for all pre-install [P]; models. The backcan is designed for pre-installation in newly constructed, non-suspended ceilings.

NOTE: The CMS 603DC/ICT and CMS BDIDC models have the transformer pre-attached to the inside of the backcan; the CMS 503DC/ICT models have the transformer pre-attached to the loudspeaker assembly.

1. Attach the backcan to a safe and secure fixing point. This can be done in a number of ways: METHOD 1: Fix the backcan to a secure fixing point by using suitable fixings with the 4 fixing holes provided on the PI backcan. (Fig.1)

METHOD 2: Secure the backcan to a safe and secure fixing point using suitable fixings with the flexible straps that are attached to the PI backcan. (Fig.2)

METHOD 3: a. Attach the PI backcan to the optional pre-mount ring (plaster ring) using the fixings provided with the pre-mount ring. (Fig.3)

b. Next, secure the wings of the pre-mount ring to a safe and secure fixing point by using suitable fixings. (Fig. 4)

Please turn over

Installation Guide for Optional Pre-Installation Backcan (PI Models Only)

1. Attach the conduit to the installed backcan. This can be done in two ways:

METHOD 1: You can use the clamp at the back of the pre-install backcan. The product will accept a squeeze connector with a thread size of up to 22 mm. To remove the cable clamp, simply uncrew the threaded washer (under the wiring cover) which holds the cable clamp in place and replace it with a conduit squeeze connector. (Fig.5)

METHOD 2: You can use any of the three knock-out points at the sides of the PI backcan (19 mm, 22 mm or 28 mm diameter). (Fig.6)

1. If conduit is not chosen as the wiring method, run an approved speaker cable to the installed can. Terminate in the top mounted cable clamp or with an approved cable connector in one of the three knock-out points at the sides of the PI backcar.

2. Cut hole in the proper location in the ceiling using a pad saw. Place the pre-install backcan over the hole. (Fig.7)

102 CMS 3.0 Series Quick Start Guide 103

1. Go to the 'Wiring and Setting Up' chapter, then return to point 6 below.

2. Side the speaker assembly through the hole. Turn the screws (denoted "Screw Fix") clockwise on the front of the speaker to extend the mounting wings. Tighten the screws until a form grip is achieved. NOTE: Screws have a PostDrive head; use of a PostDrive driver is recommended). If using a power driver, Tammy recommends a torque setting of 1.5 Nm. (Fig.8) DO NOT OVERTIGHTEN!

3. Attach the nylon safety to the hooks on the front baffle before attaching the grille by presenting it to the speakers and allowing the magnets to pull it into position. (Fig.9)

18月
Fig.5

Wiring and Setting Up

1. Open the wiring cover (if applicable) and locate the Euro-type connector plug and socket at the back of the speaker. [Fig.1]

2. For connection to an amplifier, use Pins 1 and 2 (Fig.2);

• Pin 1 is positive

- Pin 2 is negative

For connection to additional speakers in a distributed line, Pins 3 and 4 are in parallel where:

- Pin 3 is negative

- Pin 4 is positive

1. Close the wiring cover and tighten both screws on the cable clamp (if applicable).

2. Use the rotary switch on the front of the unit to select low impedance (Lo2) mode or high impedance (70 V or 100 V) for distributed applications.

THE SPEAKER IS SUPPLIED IN LOW IMPEDANCE MODE. NEVER CONNECT THE SPEAKER TO A 70/100 VOLT AMPLIFIER WHILE IT IS SET FOR LOW IMPEDANCE.

CMS 403DCe/ICTe and CMS 503DC/ICT models (all variants) use a 30 W transformer. In distributed line applications, the transformer can be tapped at 30 W, 15 W and 7.5 W, with an additional 3.75 W tap for 70 V line systems. [Fig.3]

CMS 603DC/CT and CMS 803DC models (all variants) use a 60 W transformer. In distributed line applications, the transformer can be tapped at 60 W, 30 W and 15 W, with an additional 7.5 W tap for 70 V line systems. (Fig.4)

Fig.1

140.7

[1]

Fig.1

104 CMS 3.0 Series Quick Start Guide 105

Painting

If desired, the grille and baffle panel may be painted to match the surrounding decor.

Painting the baffle:

• Carefully mask off the driver assembly using the paint mask provided to ensure that the paint does not come into contact with the cone and roll surround.
• Apply several thin coats of paint – this will provide a better finish than one overly thick coat.
  Painting the grille:
• Carefully remove the acoustically transparent grille cloth from the reverse side of the grille.
• Paint the grille and then replace the grille cloth - several thin coats of paint will provide a better finish than one overly thick coat.
• Re bond the grille cloth to the grille over the entire area using a light spray adhesive to avoid audible resonances.

CMS Series Model Dimensions

CMS 803DC BM

Hole Cut-out Size: 295 mm
Tamaño de corte del orificio: 295 mm
Tame de la decoupe du trout. 295 mm
Tamanho do recorte do furc: 295 mm
Dimensione del ritaqlio del foro: 295 mm
Gat uitgesreden grootte: 295 mm
Hallskurell Stoffes, 295 mm Promisswuppungstehres

CMS 803DC PI

Hole Cut-out Size: 295 mm
Tamaño de corte del orificio: 295 mm
Taille de la découpe du trou: 295 mm
Lochausschnitt Große: 295 mm
Tamaño do recorte do loro: 295 mm
Diministelle der Risiko betallo, 253 mm
Hörskuran strode: 785 mm
Rozmier wycięcia w otworze: 295 mm

106 CMS 3.0 Series Quick Start Guide 107

CMS Series Model Dimensions

CMS 803DC PI BACKCAN

Hole Cut-out Size: 295 mm

Hole Cut-out Size: 295 mm

CMS Series Model Dimensions

CMS 603DC BM

Hole Cut-out Size: 253 mm

Cat witnesses grade 253,000

Hälsskuren stadek: 253 mm

Hole Cut-out Size: 253 mm

CMS Series Model Dimensions

CMS 603DC PI

Hole Cut-out Size: 253 mm
Tamaño de corte del orificio: 253 mm
Taille de la découpe du trou: 253 mm
Lochausschnit Größe: 253 mm
Tamanho do recorte do fundo: 253 mm
Dimensione de maglio de 100.25 mm Est. de la aplica di 753 mm
Häskurup sterisk: 253 mm
Roomar wyciccia w otworze: 253 mm

CMS 603ICT PI

Hole Cut-out Size: 253 mm
Tamaño de corte del onificio: 253 mm
Taille de la découpe du trou: 253 mm
Lochausschnitt Größe: 253 mm
Tamanho do recorte do furo: 253 mm
Dimensione del ntaglio del foro: 253 mm
Galt ausgeschieden größte: 253 mm
natskolen 107ek. 253 mm Bonnier vucieda wefuero: 151 mm
normal by 1970, 4: 05/12.233 mm

CMS Series Model Dimensions

CMS 603DC PI BACKCAN

Hole Cut-out Size: 253 mm
Tamaño de corte del orificio: 253 mm
Taille de la découpe du trou: 253 mm
Lochausschnitt Große: 253 mm
Tamaño do recorte do rufo: 253 mm
Einheitsteile der Risikurierung. 213 mm Gesamtengaden geobt. 267 mm
Hörschung stade: 253 mm
Rozmiar wydęcia w otworze: 253 mm

CMS 603ICT PI BACKLAN

Hole Cut-out Size: 253 mm
Tamaño de corte del orificio: 253 mm
Taille de la découpe du trou: 253 mm
Lochausschritt: Größe: 253 mm
taimanio do recorte do dire. 235 mm
Dimensione del Tragno del foro: 253 mm
Hilsskursen stodeir: 253 mm
Rozmier wycięcia w otworze: 253 mm

110 CMS 3.2 Series Quikx San Guade 111

CMS Series Model Dimensions

CMS 603ICT LS

Hole Cut-out Size: 253 mm
Tamaño de corte del orificio: 253 mm
Taille de la découpe du trou: 253 mm
Lochausschnit Große: 253 mm
Tamanho do recorte do fundo: 253 mm
Dimensione de maglio de 100.25 mm Est. de la aplica di 753 mm
Häskurup sterisk: 253 mm
Roomar wyciccia w otworze: 253 mm

CMS Series Model Dimensions

CMS 503DC BM

Hole Cut-out Size: 190 mm
Tamaño de corte del orificio: 190 mm
Taille de la découpe du trou: 190 mm
Lochaußschnitt Große: 190 mm Trembe der sonstige durch 100 mm
Dimensione del rispetto del forso: 100 mm
Catuitessgaden grootte: 150 mm
Hälsskuren stadek: 190 mm
Rozmiar wycięcia w otworze: 190 mm

CMS 503ICT BM

Hole Cut-out Size: 190 mm
Tamaño de corte del orificio: 190 mm
Taille de la découpe du trou: 190 mm
Lochausschnitt Grolle: 190 mm
Tamaínho do recorte do ano: 190 mm
Dimensierte der Risiko betallo, 150 mm Gehaltzernaden mehr, 100 mm
Höckuran strode: 700 mm
Rozmier wycięcia w otworac: 190 mm

112 CMS 3.2 Series Quicks Scan Guide 113

CMS Series Model Dimensions

CMS 503DC LP

Hole Cut-out Size: 253 mm
Tamaño de corte del orificio: 253 mm
Taille de la découpe du trou: 253 mm
Lochauschnitt Große: 253 mm
Tamarino do recorte do turo: 253 mm
Dimensione de maglio de 100.25 mm Est. de la aplica di 753 mm
Häskurup sterisk: 253 mm
Roomar wyciccia w otworze: 253 mm

CMS 503ICT LI

Hole Cut-out Size: 253 mm
Tamaño de corte del orificio: 253 mm
laite de la detoupe du trou: 253 mm
Lachalusschnitt Grosse: 253 mm
caminato di teorite di min: 255 mm Dimensione del italie del fuve: 263 mm
Gesitzermoden operte: 161 mm
Hälsskumpsterlek: 251 mm
Rozmiar wyciecia w otworze: 253 mm

CMS Series Model Dimensions

CMS 503DC FI

Hole Cut-out Size: 190 mm
Tamaño de corte del orificio: 190 mm
Taille de la découpe du trou: 190 mm
Lochausschnitt Große: 190 mm
Tamaño do recorte do rufo: 150 mm
Linnelschre der Raquin der Hid. 150 mm Gesüberschre des 100 mm
Hölschungen stade: 100 mm
Rozmiar wycięcia w otworze: 190 mm

CMS 503ICT PI

Hole Cut-out Size: 190 mm
Tamaño de corte del orificio: 190 mm
Taille de la découpe du trou: 19
Lochaußschnitt Größe: 190 mm
Tamaño do recorte do euro. 150 mm
Dimensierte der Risiko der 100 mm Gat vittverschenden oder 100 mm
Hörschuss grade 200 mm
Rozmiar wydzieja w otworze: 190 mm

114 CMS 3.2 Series Quicks Scan Guide 115

CMS Series Model Dimensions

CMS 503DC PI BACKCAN

Hole Cut-out Size: 190 mm

Hole Cut-out Size: 190 mm

CMS Series Model Dimensions

CMS 403DCe

Hole Cut-out Size: 187 mm
Tamaño de corte del orificio: 187 mm
Taille de la découpe du trou: 187 mm
Lochaußschnitt Große: 167 mm Trembe der sonst der lang 167 mm
Dimensione del rispetto del forso: 187 mm
Cat witnesses grade 157,000
Hälsskuren stadek: 187 mm
Rozmiar wycięcia w otworze: 187 mm

CMS 403ICTe

Hole Cut-out Size: 187 mm
Tamaño de corte del orificio: 187 mm
Taille de la découpe du trou: 187 mm
Lechausschnitt Größe: 187 mm
Tamaño do recorte do rufo: 187 mm
Dimensione der Risiko deniro. 187 mm
Hilchuren stodein: 187 mm
Rozmiar wydeca w otworze: 187 mm

116 CMS 3.2 Series Quicks San-Guade 117

Technical Specifications

CMS 8030C/Model CMS 8030CQ/Model
Performance
Frequency response (3 dB) *	47 Hz 10 MHz/10 kHz	47 Hz 30 kHz
Frequency range (10 dB) *	40 Hz 35 MHz/10 kHz
Frequency range (10 dB) *	41 Hz 35 MHz/10 kHz
System sensitivity (W or Tm) *	50 dB (1 W = 4 for 16 GHz), 95 dB (1 W = 4 V/m) * Oned
Nominal Coverage Angle underground central 3D degree nominal
Power Handling*
Average 50 W
Programme 180 W
Peak 300 W
Recommended Amplifier Power 160/2 g / 16 Ohms
Nominal Impedance (Co, Z) / 16 Ohms
Rated minimum SPI
Average	112 dB	113 dB
Peak	110 dB	119 dB
With DIF60 - Average	110 dB	111 dB
Transformer Steps (in front output switch)
70V	(4) W (83 c) / 120 W (165 c) / 15 W (230 c) / 25 W (660 c) / 0.85 & low impedance operation, Refer to Note 4.
100 V	(6) W (165 c) / 200 V (100 c) / 15 V (660 c) / 0.85 & low impedance operation Refer to Note 4.
Transducers
Dual Concentric point source driver	1 x 250 mm (20"). dual Concentric driver using Drammagnet technology
Low Frequency	4 mm (25") color and, colored and blue paper put zone
High Frequency	25 mm (1.30") PCI zone
Physical
Endurance
Backion	Zone colors used
Backie	Rebees loaded 10,947-4 rated 645
Grid	Stairs, with whether connected to charging
Safety Features	Soldering location zone of endzone at the load bearing safety band
Camping Design	Secure by single clock Min / Mass clamping range 9.5 mm (10.35") / 45 mm (12.35") Recommended during torque: 1.5 Min
Backion Options
81nd Mount (80')	Complete with fixed backion	—
Preload (P%)	Separated backion for pre installation	—
Cable Entry Options	Cube clamp & sequence connection for conduct up to 22 mm
Conduit Breakouts on PI Backion	3 sets of horizontal position 15 x 22 x 28 mm (10.75" x 0.87" x 1.01)
Connectors	Removable locking connector with transthermal wire with Trap-through facility
Compliance	III, 1400, II, 2043, CT

CMS 803DC Models CMS 803DCQ Model

Physical
Dimensions
Board Diameter	316.0 mm (12.56")
Front of ceiling to rear of backseat	—	472.5 mm (12.22")
Front of ceiling to top of safety loop	—	322.7 mm (12.90")
EM Mount Front of ceiling to rear of backseat	112.5 mm (12.37")	—
EM Mount Front of ceiling to top of safety loop	322.7 mm (12.90")	—
FL Modules: Front of ceiling surface to rear of speaker and	125.6 mm (8.34")	—
FL Module: Front of accessory heater at rear of top of safety loop	166.5 mm (6.66")	—
Hole cutout diameter (all models)	295 mm (11.60")
Net Weight (gal)	—	8.5 kg (18.24 lb.)
CNS-80000 FL	8.5 kg (18.34 lb.)	—
CNS-80000 FL	5.0 kg (11.02 lb.)	—
FL Jakarta	4.2 kg (9.25 lb.)	—
Included Accessories	G-Box, the-edge box, paint mask, cut-out template, grille
Optional Accessories	Flower (musting, Ace-girls)
Packed Quantity	2

Trav
1. 2017年1月1日，公司召开2017年第一次临时股东大会，并通知全体董事。
2.3.1.
S. Inghaw, 2016, 38: 19-4581a.
A. 2018年，公司与关联方、董事、监事、高级管理人员不存在关联关系。
V. Bung, al., 2016, and 2017, doi: 0.5.e.Haee1a/085432C05432C03.cdr, https://doi.org/10.10001.com
In the case of the solution was not obtained. From the mean value of the solution, which is derived from the calculation process and the result of the solution, we also could be obtained at the level
where the first line is directly to us. From every direct space that when they are equal and equal,

118 CMS 3.2 Series Quicks San-Guade 119

Performance
Frequency response (3 dB) 15M DCDCs at 75 Hz - 30 kHz	75 Hz - 22 kHz
Frequency range (10 dB) 15M DCDCs at 50 Hz - 30 kHz	11 kHz - 24 kHz
Frequency range (10 dB) 15M DCDCs at 60 kHz - 30 kHz	40 kHz - 24 kHz
System sensitivity (1 U ± 1 m) 16		91 dB (11% = 14% for 16 Chms)
Nominal Coverage Angle 90 degrees central 92 degrees central
Coverage Angle (1 MHz to 4 MHz) 92 degrees
Directivity Factor (2) 7.1 arranged 1 milli-cable
Directivity Index (100 7.9 average 1 milli-cable)
Power Handling*
Average	80 W	62 W
Programme	100 W	120 W
Peak	320 W	290 W
Recommended Amplifier Power	100 W ± 16 Ohms	120 W or 16 Ohms
Nominal Impedance (Lp, Z)	1⁄2 Ohms
Rated minimum SPL
Average	110 dB	105 dB
Peak	116 dB	115 dB
Transformer Capsule (in front entry circuit)
70 V	16 W (30 Hz) / 10 W (100 Hz) / 15 W (200 Hz) / 15 W (600 Hz) / 20 W (600 Hz) / 20 W (600 Hz) / 20 W (600 Hz) / 20 W (600 Hz) / 20 W (600 Hz) / 20 W (600 Hz) / 20 W (600 Hz) / 20 W (600 Hz) / 20 W (600 Hz) / 20W	—
100 V	10 W (30 Hz) / 10 W (100 Hz) / 15 W (600 Hz) / 15 W (600 Hz) / 20 W (600 Hz) / 20 W (600 Hz) / 20 W (600 Hz) / 20 W (600 Hz) / 20 W (600 Hz) / 20 W (600 Hz) / 20 W (600 Hz) / 20 W (6)
Crossover	—	7 Fast independently coupled
Transducers
Dual Concentric point source driver	1 x 165 mm (3.5" Dual Congenitic drive, using Dammal region technology	—
Low Frequency	44 mm (1.5" voice oil, treated/multi fiber power pump cone)	165 mm (5.3") nonsolid loaded polypropylene
High Frequency	25 mm (1.00" PBI cone)	1 L aluminum dome
Physical
Endurance
Backion	Continuous used
Rums	Retire loaded (10-90) 2 rated A/S
GTe	Steel, with ethylbenzeneic staining
Safety Features	Solder ring located in rear of endzone for load bearing safety tone
OMS 120K115	18 1400 1000V certification for the Safety applications
Comping Design	Standard bending clamping Mn / Max clamping range 0.5 mm (2.5" / 162 mm (2.36") Recommended clamping torque: 1.5 Km
Backion Options
Bird Mount (BBS)	Complete with food backbone
Pre-kgall 25°	Separate backbone for one manufacturer
Cable Entry Options	Cube clamp & sensor connector for conduct up to 22 mm
Conduit Breakouts on PI Backbone	3 sets of interdural positions: 19/22/28 mm (0.75" / 0.87" / 1.10")
Connectors	Renewable loading connector with sensor terminals with "fast through" facility
Compliance	III 1400, UI 2540, CF

CMS 603DC Models CMS 603ICT Models

Physical
Dimension
Fuel Diameter	274.3 mm (10.9")
BM Mount Front of ceiling to rear of backbone	155.8 mm (10.6")	216.5 mm (10.9")
BM Mount Front of ceiling to rear of safety loop	273.3 mm (10.9")	275.8 mm (10.9")
FL Width, Front of ceiling surface to rear of operation unit	100.2 mm (5.9")	103.0 mm (5.9")
FL Width, front of accessory back unit behind to rear of safety loop	166.5 mm (6.6")
Hole cutout diameter (all models)	251 mm (6.9")
Net Weight (cat)
COS 6003C BM	6.6 kg (14.6 lb)	—
COS 6003C FI	3.8 kg (6.37 lb)	—
COS 6003C BM	—	5.7 kg (11.9 lb)
COS 6003C FI	—	2.7 kg (5.35 lb)
FL Backsn	1.2 kg (6.3 lb)
Included Accessories	C Bag, the bridge bit, paint mask, cat or template, grille
Optional Accessories	Parental ring, face grille
Packed Quantity	2

5.46
2.1.4.3.10
Sler pier avreb@qop278-34518-0366
Cib+278.7 transfer electron/MS: A B I/ mab h i m a d i r b e c p t a l l b a d o r
We have been a new 2-year year-end week ended March 30, 2015. The following news is presented in the following:
For example, the actual values of the results are not available in the calculations that are derived from the results. The results are not available in the results.
The following table is a list of 10 items, including the first item and the last item.

120 CMS 3.0 Series Quick Star Guide 121

Performance
Frequency response (-3 dB)1	85 Hz - 57 kHz BW/Backion 88 Hz - 22 kHz
Frequency range (-10 dB)1	24 Hz - 54 kHz BW/Backion 77 Hz - 24 kHz
Frequency range (-10 dB)2	25 Hz - 54 kHz BW/Backion
System sensitivity (1 V ± 1 m)3	BF-63 (1 W = 1 V for 16.0 m/s)
Nominal Coverage single 90 degrees critical
Power Handling4
Average 60 W
Programmer 120 W
Peak 240 W
Recommended Amplifier Power 120 V ± 16 ohms
Nominal Impedance (0.0, Q) 16 ohms
Rated maximum SPI
Average 100 dB
Peak	11.40
Transformer Taps (in front rotary solids)
70 V	300 W (65.0 V / 15 W, 200.0 V / 7.5 W, 660.0 V / 7.3 W, 220.0 V) / CFP & low impedance operation
100 V	30 W (130.0 V / 15 W, 640.0 V / 7.5 W, 1425.0 V / 69.6 W) or improved sensor
Transducers
Dual Concentric point source driver	1 a 135 mm (5.37" Dual Concentric drive, using Onemagnet Ion loadings
Low Frequency	35 mm (1.26") wide tail, heated mesh fiber super polyp zone
High Frequency	30 mm (0.76") Hi drive
Physical
Endurance
Backion	300 plated steel
Ratios	Before loaded 1.34V and 485
Grid	Steel, with another recent mounting
Safety Features	Safety ring installed at rear of enclosure for load bearing safety bound
Camping Design	Security triple clamp tip / thin clamp loop range 9.5 mm (0.37") / 60 mm 12.38" free commences clamp torque: 1.5 Km
Backion Options
Direct Mount (BV)	Complete with mounted backion	—
Pre install (%)	Separate backion for pre-installation	—
Cable Entry Options	Cable clamp-down/assessor connector for contact up to 22 mm
Contact Breakouts an PI Rackton	3 sets of rectangular pinsets 19 / 22 / 28 mm(1.27" / 0.83") / 1.01"	—
Connectors	Retractable locking connection with severe terminals with "loss through" facility
Compliance	UL-1900, UL-2045, OL
Dimensions
Board current	205.9 mm (0.11")	274.6 mm (0.79")
Front of ceiling to rear of backion	—	90.6 mm (0.83")
BOM/Inde: Front of ceiling to rear of backion	100.0 mm (2.40")	—
BOM/Inde: Front of ceiling to top of safety loop	225.3 mm (2.04")	—
PI Model: Front of ceiling surface to rear of safety loop	133.3 mm (5.25")	—
PI Model: Front of auxiliary backion trunk to top of safety loop	133.5 mm (6.34")	—
Hole output diameter [all models]	190 mm (2.48")	253.0 mm (5.06")
Net Weight (kg)	—	4.7 kg (10.36 lbd)
OMS 5DC/DC 3M	4.2 kg (5.77 lb)	—
OMS 5DC/DC 3M	3.2 kg (2.06 lb)	—
PI Rackton	1.3 kg (4.18 lb)	—
Included Accessories	3 Bag, tile antenna kit, point mark, cut and template, g/dle
Optional Accessories	Plaster limit ring, square hole
Packed Quantity	2

备注：
1. 2023年1月1日
1. 上海发展(集团)有限公司
1. 本次发行的股份总数为2006年10月31日
1. 2017年 ，公司及子公司对外担保情况
A. 100% 面积率 ( m^2cm^2) ,所以 100% 面积率 100% 的 100% 面积率 100% 的 100% 面积率。
In our property policy, we will not have a free spin. The results are set to be the same, and the price of the property is not at all. In the price of the property is the result that we will pay up from the sale of the property, with 10%
The following table provides the original text: "The English text in the source image is not a standard character. It is not a visual representation of the text in the source image."

(1) 本说明仅供参考。

CMS SOBCT Models		CMS SOBCT LP Model
Performance
Frequency response [1-3 dB]1	85 Hz - 22.9Hz FM Elution 88 Hz - 50 Hz
Frequency range [1-10 dB]2	74 Hz - 24.6Hz FM Elution 77 Hz - 54 Hz
Frequency range [1-10 dB]3	71 Hz - 24.6Hz FM Elution
System conductivity [1 W g / 1 m]3	20 dB [1 W = 4 V for 16 Chms]
Nominal Coverage Angle: 90 degrees nominal
Coverage Angle [1/20 to 6 MHz]	105 degrees	—
Directivity Factor (Ω)	5.6 average 1 kHz to 6 kHz	—
Directivity Index (ID)	70 average 1 kHz to 6 kHz	—
Power Handling3
Average 40 W
Frequency 100 W
Peak: 200 W
Recommended Amplification Power 100 W g 16 Ohms
Nominal Impedance [Hz, Zr 16 Ohms]
Rated maximum SPL
Average 100 dB
Peak:	112 dB
Transformer Taps (via front mounting point)
30 V	30 W (105 Ω) / 115 W (132 Ω) / 73 W (820 Ω) / 3.75 Ω / (300 Ω); 26F & low impedance operation
103 V	37 W (200 Ω) / 15 Ω (600 Ω) / 73 W (120 Ω) / 301 & low impedance operation
Crossover	7 Hz approximately coupled	—
Transducers
Low Frequency	110 mm (5.25" mineral loaded polypropulse)	1 x 100 mm (5.0" mineral loaded polypropulse)
High Frequency	ICI aluminum dome	ICT
Physical
Extrusive
Backout	Zinc colored steel
Baffle	Belle loaded UL 99% coated M/S
Circle	Circle with weather-resistant coating
Safety Features	Safety ring located at rear of mechanical front end bearing safety ring
Clamping Design	Security toggle clamp Film / Max clamping range 9.5 mm (25.37" y" 50 mm (2.36"); Recommended clamp torque: 1.5 Km
Backtan Options
Flint/Center (FM)	Complete with feed backtan	—
For Initial (FR)	Separate backtan for pre-avoliation	—
Cable Entry Options	Cable clamp & square connection for contact cars to 22 mm
Condul Konsicouts on PI Backtan	3 sets of horizontal positions: 16.722 / 28 mm (x,y) / 25.60° / 1.10°	—
Connections	Reversible locking connectors with cars to maintain with "loop through" facility
Compliance	III, 1986, II, 2041, CT
Dimensions
Metal Diameter	250.9 mm (2.11")	274.0 mm (29.39")
Front of ceiling to rear of backtan		38.6 mm (2.68")
BM Model: Front of ceiling to rear of backtan	381.5 mm (2.42)	98.6 mm (10.61)
BM Model: Front of ceiling to rear of safety stop	205.8 mm (8.10")	—
FLWedel Front of ceiling surface to rear of speaker unit	131.7 mm (5.39")	—
FLWedel more or necessary backtan based to top of safety loop	151.5 mm (6.04")
Hole colour diameter (all models)	193 mm (7.08")	253.0 mm (26.61")
Net Weight (wt)	—	4.4 kg (9.23 lb)
CMS SOBCT FM	3.9 kg (8.10 lbs)	—
CMS SOBCT FI	2.95 kg (6.50 lbs)	—
FI Backtan	3.9 kg (2.10 lbs)	—
Included Accessories	Cling, the bridge out, paint mask, cut-out template, gate
Optional Accessories	Paceter/molding, knee gasket
Packed Quantity	2

Performance
Frequency response (-3 dB)18	110 Hz ~ 540Hz SM Backcom 110 Hz ~ 22 kHz
Frequency range (10 dB) 18-30Hz - 540Hz 60Hz	Iccm.01 Hz ~ 24 Hz
System sensitivity (110 g / 1 m)19	80 dB (19 ~ 47 for 16 Chms)
Nominal Coverage Angle 50 degrees central
Coverage Angle (1 MHz to 6 MHz) — 120 degrees
Directivity Factor (Q) — 3.26 averaged 1MHz to 6Hz
Directivity Index (D) — 6.30 averaged 1kHz to 6Hz
Power Handling10
Average 40 W
Peak	165 W
Recommended Amplifier Power	40 W @ 16.4GHz
Nominal Impedance (Cu, Z)	16.0 gm
Rated minimum SPL
Average	104 dB
Peak	110 dB
Transformer Caps (6x front, stationary solid)
D/Y	30W (165 W) or 15/20 (180 W) or 1.5 W (660 W) or 2.5 W (1130 W) or 2.6W & low impedance operation
100 V	30W (130 W) or 7.5 W (660 W) or 2.5 W (1130 W) or 2.6W & low impedance operation
Crossover		7 Mio inductively coupled
Transducers
Dual Concentric point source driver	1 x 100 mm (40") (One Concentric down, using thin instrument technology)	100 mm (40") (normal loaded polypropylene)
Low frequency	15 mm (1.38") power end, mounted multi-tower paper pulse zone	10 mm (5.25") ICT aluminium dome
High Frequency	20mm (0.37) / 92dome	—
Physical
Endosize
Backcom	Refer loaded 10 L/40#-loaded ABS
Baffle	Refer loaded 10 L/40#-rated ABS
Grike	Steel, 40% weather resistant loading
Safety Features	Safety ring location, near of the source for load bearing safety band
Comping Design	Alim / No clamping range: 0.2 mm (0.0") or 26.0 mm (5.29")Recommended lamp torque: 5.5 Km
Backcom
Wind Mount (MW)	Completely with load head cover
Connectors	Removable locking connectors with one terminal with "Loop through" facility
Compliance	IL 1.48E, IL 2041, CT
Dimensions
Roof diameter	205.0 mm (5.0")
Front of ceiling so rear of pod	147.6 mm (5.6")
Hole colour diameter	187 mm (7.36")
Net Weight (kg)	3.2 kg (2.55 lb)	3.0 kg (5.61 lb)
Included Accessories	C Ring, the bridge kit, paint mark, are out template, guide
Optional Accessories	Plaster (mid) ring
Packed Quantity	2

例8.1
1. Bapacatilus, 2007; Fucan and E. Kellin
1. We have a similar job, not held at 200 and 500 years ago when we have the job in the work of 2000. We also have other men than you.
In the following two different conditions, the first and second conditions for an anti-oxidation reaction were performed by the same method. The second condition was used to assess the effect of the drug on the presence of the drug in the absence of the drug.

124 CMS 3.0 Series Quick Start Guide 125

Other important information

Important information

1. Register online. Please register your new Music Tribe equipment right after you purchase it by visiting musictribe.com. Registering your purchase using our simple online form helps us to process your repair claims more quickly and efficiently. Also, read the terms and conditions of our warranty, if applicable.
2. Malfunction. Should your Music Tribe Author and Reseller not be located in your vicinity, you may contact the Music Tribe Authorized Fulfill for your country listed under "Support" at musicitibe.com. Should your country not be listed, please check if your problem can be dealt with by our "Online Support" which may also be found under "Support" at musicitibe.com. Alternatively, please submit an online warranty claim at musicitibe.com BEFORE returning the product.
3. Power Connections. Before plugging the unit into a power socket, please make sure you are using the correct mains voltage for your particular model. Fuzzy fuses must be replaced with fuses of the same type and rating without exception.

Hereby, Music Tribe declares that this product is in compliance with Directive

2011/65/Ell and Amendment 2015/863/EU, Directive 2012/19/EU, Regulation

519/2012 REACH SWHC and Directive 1907/2006/EU, and this passive product is not applicable to EMC Directive 2014/30/EU, LV Directive 2014/35/EU.

Full text of EU DoC is available at https://community.musictribe.com/

EU Representative: Music Tribe Brands DK A/S

Address: Gammel Strand 44, DK-1202 København K, Denmark

UK Representative: Music Tribe Brands UK Ltd.

Address: 6 Lloyds Avenue, Unit 4CL London EC3N 3AIX, United Kingdom