Bella - Breast pump Neno - Free user manual and instructions

USER MANUAL Bella Neno

1. Do not use the breast pump during pregnancy – this can cause early delivery.

2. Do not use the device if you suer from chronic diseases or oversensivity

that would make using the device painful to you.

3. Before each use of the device, make sure that no component is damaged.

4. a breast pump if any of its components are clearly damaged.

5. Keep the device away from children and animals.

6. For hygienic reasons, only one person should use the breast pump.

7. Keep the pumping part of the device away from water.

8. Avoid exposing the device to mechanical damage caused by, for example,

9. Store the silicon parts of the breast pump away from hot surfaces to avoid

10. Store only milk that has been drained using a clean and disinfected breast

11. Do not clean parts of the device with abrasives.

12. Do not try to repair the breast pump yourself – this will void the warranty.

13. If the use of the device causes pain or severe discomfort, turn it o and

14. the breast pump away from your breast.

15. Do not clean the tube too oen and make sure it is dry before use. A wet

tube can damage the device.

16. Do not charge the device with a voltage higher than specied in the

Power buon: Hold for 2 seconds to turn the breast pump on or o. Mode change: Press the buon to change the mode. The device will automacally switch from smulaon to expression mode aer 2 minutes. The device can save sengs and has a me counter.12 When you turn on the device, the sengs from the previous use of the device are automacally turned on. The breast pump will automacally turn o aer 30 minutes of use. Sucon power: + increases sucon power; - reducon of sucon power (smulaon mode: L1-L6; expression mode: L1-L9). Baery status: Indicates the amount of baery power remaining. Charge the breast pump if the baery is low. Session duraon: Indicates how long you have been using the breast pump. The device will turn o automacally aer 30 minutes of use.

1. Remove the cap from the breast shield before each use.

2. Pull down on valve to remove from connector.

3. Seperate the connector from the sucon bowl and sucon cap.

Cleaning and sanizing are two dierent acvies. They must be done separately to protect your child and ensure that the breast pump works properly. Cleaning - washing the surface of the device and removing dirt. Sanizing - killing organisms such as bacteria or viruses that may be present on the Surface of the device. Breast shield Breast pump elements (connector, sucon bowl, sucon cap) Bole and teat set Before rst use Clean and sanize Clean and sanize Clean and sanize Aer every use Clean Clean Clean Once a day Sanize Sanize Sanize

07. ASSEMBLING THE BREAST PUMP

1. Wash your hands thoroughly with soap and water before touching the

breast pump and breast.

2. Aach the breast shield, sucon bowl and sucon cap to the connector.

3. Place the valve in the connector and screw the milk bole onto the connec-13

tor by turning it clockwise unl it stops turning.

4. Connect the tube to the sucon cap.

5. Connect the tube to the appropriate port on the pumping device.

Tips: a. Check the breast pump components for damage before each use. Repla- ce damaged items with new ones as needed. b. Always check the cleanliness of the elements before using the machine. c. To avoid damage to the breast pump, make sure that all its parts are dry before using it.

08. CHARGING THE BREAST PUMP

Before the rst use, charge the breast pump for 2 hours by connecng it to the power supply using the USB cable. The baery icon on the display will be full when charging is complete.

09. USING THE BREAST PUMP

1. Place the breast shield on the breast so that the nipple is inside the drainage

2. Press the breast shield and the connector to your breast, using your thumb

and forenger. Support your chest with the palm of your hand.

3. Turn on the breast pump by pressing the power buon and select the mode

of operaon that suits you.

4. Press the power buon to turn o the breast pump aer use and place the

lid on the breast shield to protect the machine from dust. a. The breast pump starts work in the smulaon mode. Set the sucon power to a level that is comfortable for you using the +/- buons Smulaon mode - fast pumping that mimics the natural sucking of breast milk by a baby, smulang milk ow. b. Aer 2 minutes, the breast pump will automacally acvate the expres- sion mode. Adjust the level of sucon using the +/- buons to nd the highest level of sucon that is comfortable for you. If milk begins to ow out of your breast before two minutes pass, press the mode buon to manually switch to the expression mode. Expression mode - slower pumping which gently and eciently sucks breast milk. c. In the expression mode, increase the sucon power unl you feel slight discomfort (not pain) and reduce the sucon power by one degree.

10. REPLACEMENT OF CONSUMABLE PARTS

Consumable parts are subject to natural wear and tear during operaon of the breast pump and are therefore not covered by the manufacturer’s warranty.14 Worn components of the breast pump that come into contact with milk should be replaced. A worn component has a crack, deformaon, tarnishing or a disnct change in colour.

• Replace the diaphragm every 8 weeks (if you use the breast pump 1-3 mes a day) or every 3-4 weeks (if you use the breast pump more than 3 mes a day).

• Replace the valve every 2-3 months (if using 1-3 mes a day) or every 4 weeks (if using more than 3 mes a day).

• Replace the funnel every 6 months if you use the breast pump more than 3 mes a day.

• Replace the tube only if moisture enters the tube or the tube is damaged.

1. The machine does not start: ensure that the breast pump is connected to a

working electrical outlet. If the breast pump has no power source, its display will not turn on and no error message will appear.

2. No/ poor sucon: make sure all parts of the breast pump are correctly

posioned. Disassemble the breast pump and make sure that all parts are clean and undamaged. Assemble the breast pump again according to the instrucons in secon „Assembling the breast pump”.

3. More milk has owed out of the breast than the bole can hold: switch

o the breast pump and unplug it. Use a damp (not wet) cloth to wipe the breast pump. When all parts of the device are dry, reassemble them.

12. LONG-TERM STORAGE

1. The breast pump has a built-in baery. To protect against damage, the

device goes into storage mode aer a long period of inacvity. To turn o storage mode, connect the device to power and charge it for 2 hours.

2. Before pung the breast pump away for a longer period of me, make

sure that: a. All parts of the breast pump are clean. b. You have cleaned the pumping device. c. The device’s baery is fully charged.

13. CLEANING INSTRUCTIONS

Prepare: mild soap or other cleaning agent, clean dish towel, drinking-quality water. Parts that need to be washed or disinfected: - Breast shield, - Milk bole, - Connector, - Valve, - Sucon cup, - Sucon bowl,15 - Breast shield dust cap.

- Wash all parts that have had direct contact with breast milk immediately aer use. This helps you will avoid residue and the growth of bacteria in the device. - Use only drinking-quality water (tap or boled) to clean the appliance. - When cleaning valves, do not use small instruments such as brushes. Be careful not to pierce the part. - Disassemble, wash and rinse all parts of the device that have come into direct contact with breast milk (except for the pump).

1. Cleaning the breast pump components (Before rst use and aer each use):

Step 1 - Disassemble the device and rinse all parts that have come into contact with the breast and milk in cold water to get rid of the remains of milk and any residue. Step 2 - Soak in warm, soapy water for 5 minutes, then wash and rinse Step 3 - Let the parts air dry. Store dry device parts in a cool and dry place when you’re not using them.

2. Sterilizaon of the breast pump components (before rst use and aer use):

Step 1 - Fill the pot with enough water to cover all parts of the disassembled ap- pliance. Bring the water to a boil before you put the unfolded breast pump inside. Step 2 - Place the parts of the device in boiling water for 10 minutes. Step 3 - Let the parts air dry. Store dry device parts in a cool and dry place when you’re not using them.

3. Cleaning the pumping device:

Prepare: mild soap or other cleaning agent, clean dish towel. Parts that need to be cleaned: pumping device.

- Do not submerge the pumping device in water. - Do not rinse the pumping device with water. - When cleaning the display of the pumping device, use only a damp, so cloth with a mild soap or cleaner. Stronger cleaning products or abrasive materials can destroy the display.

The product is covered by a 24-month warranty. The terms of the guarantee can be found at: hps://neno.pl/gwarancja Details, contact and website address can be found at: hps://neno.pl/contact/?lang=en Specicaons and contents of the kit are subject to change without noce. We apologise for any inconvenience.16