ASB 24 - Drill Alpha Tools - Free user manual and instructions

Product type	Cordless impact drill/driver
Brand	Alpha Tools
Model	ASB 24
Power supply	Battery 24 V = (Ni-Cd battery)
No-load speed	0-360 rpm (speed 1) / 0-1100 rpm (speed 2)
Torque	10 mechanically adjustable stages
Chuck capacity	2 to 13 mm
Weight	5.4 kg
Charger voltage	230 V ~ 50 Hz
Charging current	2.5 A
Charging time	Approximately 1 hour
Sound pressure level LPA	85.2 dB (A)
Sound power level LWA	98.2 dB (A)
Vibration	< 2.5 m/s²
Rotation direction	Right and left reversible
Main functions	Drilling, impact drilling, screwdriving with torque adjustment
Delivery contents	Drill/driver, 2 batteries, charger, carrying case
Maintenance and cleaning	Protect from moisture, clean with a dry cloth, replace damaged cables by a specialist
Safety	Use safety goggles, do not expose to rain, keep out of reach of children
Spare parts and repairability	Repairs must be carried out by a qualified electrician. Spare parts available on request with type and article number
Warranty	5 years from purchase date, covering material and manufacturing defects

Frequently Asked Questions - ASB 24 Alpha Tools

How to charge the battery for the first time?

Before first use, the battery is not charged. Insert the charger into a 230 V socket, remove the battery from the handle by pressing the side buttons, then place it on the charger. The red LED indicates charging; after approximately 1 hour, the green LED lights up, signaling that charging is complete.

How to adjust the torque?

Turn the front adjustment ring to one of the 10 numbered stages. A lower torque is suitable for small screws, a higher torque for larger screws. When the torque is reached, a click is heard.

How to switch from drilling to impact drilling?

Set the front adjustment ring to the 'Drill' symbol for normal drilling, or to the 'Hammer' symbol for impact drilling. For impact drilling, also set the torque ring to the 'Drill' symbol.

How to change speed (speed 1 or speed 2)?

Use the speed selector switch located on top of the tool. Set it to '1' for slow speed (0-360 rpm) or to '2' for fast speed (0-1100 rpm). Only switch when the tool is stopped.

What to do if the battery does not charge?

Check that the mains socket is live and that the charger contacts are clean and well connected. If the problem persists, send the charger and battery to a service center.

How to reverse the rotation direction?

The slide switch above the trigger allows you to choose rotation to the right or left. In the central position, the trigger is locked. Only switch when stopped to avoid damaging the gear.

What accessories can I use with this drill?

Use sharp drill bits and screwdriver bits in good condition. The chuck accepts bit shanks from 2 to 13 mm. For screws, prefer self-centering types (Torx, Phillips).

How to maintain the drill?

Protect the tool and charger from moisture and rain. Clean with a dry cloth. Have damaged cables replaced by an electrician. Repairs must be entrusted to a professional.

How to dispose of used batteries?

Do not dispose of batteries in household waste as they contain toxic cadmium. Return them free of charge to an appropriate collection point or to the ISC company.

What is the warranty period?

The warranty is 5 years from the date of purchase. It covers material and manufacturing defects. Spare parts and labor are free, but subsequent damages are not covered.

USER MANUAL ASB 24 Alpha Tools

⑥ Important: Read and note the operating instructions and safety regulations before using!

③8 Please pull out pages 2-5

Technical line drawing of a drill bit with a battery and screwdriver (no text or symbols)

⑩ Lieferumfang:

1 Stück Akku-Bohr-Schrauber	1	cordless	drillscrewdriver
1 Stück Wechselaku	1	removable	battery	psck
1 Ladegerat	1	battery	charger
1 Aufbewahrungskoffer	1	storage	case

Figure 1: Torque adjustment facility; selector drill / hammer mode

Figure 2: 1st gear / 2nd gear selector switch

Figure 3: Battery capacity reading

Figure 4: Forward / Reverse selector switch

Figure 5: On/Off switch

Figure 6: Removable battery pack

Important notes:

It is imperative to read these notes before putting your battery-powered drill/screwdriver into operation:

1. The removable Ni-Cd battery pack supplied with your battery-powered drill/screwdriver has to be charged before you use the tool for the first time.
2. Use the supplied battery charger to charge the battery pack. It takes a maximum of 1 hour to charge an empty battery. Do not use the supplied battery charger to charge any other tools or appliances.
3. The battery pack reaches its maximum capacity after approx. five discharge/charge cycles.
4. Ni-Cd batteries will also discharge when they are not in use. It is recommended, therefore, to charge the batteries

regularly.

1. Please note the data quoted on the rating plate of the battery charger. Operate the charger only from the same mains voltage as that quoted on the rating plate.
2. In periods of heavy duty the battery pack will grow warm. Allow the battery pack to cool to room temperature before starting to charge it.

Safety regulations:

1. Protect your battery-powered drill/screwdriver and charger from the damp and rain.
2. Keep the charger and battery-powered drill/screwdriver safe from children.
3. Use only sharp drill bits and undamaged, properly fitting screwdriver bits.
4. Wear suitable working clothes and safety goggles.
5. Never use the battery-powered drill/screwdriver and charger in the vicinity of vapours and combustible liquids.
6. Look for concealed electric cables, gas pipes and water pipes before drilling and screwdriving in walls.
7. Never throw old batteries into an open fire. Risk of explosion!
8. Avoid contact with leaky batte-

GB

ries. Should contact arise nevertheless, wash the affected area of skin immediately with soap and water. If battery acid gets in your eye, rinse the eye with clear water for at least 10 minutes and consult a doctor immediately.

1. Protect the charger and its cable from damage and sharp edges. Damaged cables are to be replaced immediately by an electrician.
2. Examine your tool for any signs of damage. Have repairs carried out only by an electrician.
3. Make sure that the contacts of the Ni-Cd battery pack do not touch other metallic objects, e.g. nails and screws. Risk of short-circuiting!

Putting into operation:

Loading the Ni-Cd battery pack

1. Check that your mains voltage is the same as that quoted on the rating plate. Insert the charger in a socket-outlet.

2. Pull the battery pack out of the handle (Figure 6) by depressing the clips on the side.

3. Insert the battery pack in the charger. The green LED lights up. Press the "Set" button to charge the battery. The red LED lights up during the charging cycle. When charging

finishes after approx. 1 hour the green LED lights up. The temperature of the battery may rise slightly during the charging operation. This is normal.

If the battery pack fails to become charged, please check

● whether there is voltage at the socket-outlet

● whether there is proper contact at the charging contacts on the charger.

If the battery still fails to become charged, please return

● the charger

● the battery pack to our Customer Service Department.

Timely recharging of the Ni-Cd battery pack is recommended in the interest of long battery life. Recharging is always necessary when you notice that the power of the battery-powered drill/screwdriver is decreasing.

Never allow the battery pack to discharge completely. This will result in damage to the Ni-Cd battery pack!

Adjusting the torque (Figure 1)

The Alpha-tools battery-powered drill/screwdriver is equipped with a 10-step mechanical torque adjustment facility. The torque for a speci-

11

GB

fic size of screw is selected with the set-collar (Figure 1). The correct torque depends on several factors:

● on the type and hardness of material in question
● on the type and length screws used
● on the requirements needing to be met by the screwed joint.

The clutch disengages with a gra- ting sound to indicate when the set torque is reached.

Selecting drill or hammer mode (Figure 1)

For normal drilling, turn the front set-collar to the „drill“ symbol. For drilling with hammer action, turn the front set-collar to the „hammer“ symbol and the set-collar for torque adjustment to the „drill“ symbol. In this setting the slip clutch is inactive. The maximum torque is available in drilling mode.

Changing over from 1st gear to 2nd gear (Figure 2)

You can work at a higher or lower speed depending on the position of the selector switch. To avoid damaging the gear unit you should only change over gears when the tool has stopped.

Forward/Reverse switch (Figure 4)

With the slide switch above the On/Off switch you can select the direction of rotation of the battery-powered drill/screwdriver and secure it against being switched on accidentally. You can choose between clockwise and anticlockwise rotation. To avoid causing damage to the gearing it is advisable to change the direction of rotation only when the tool is at a standstill. The On/Off switch is blocked when the slide switch is in centre position.

On/Off switch (Figure 5)

Infinitely variable speed control is possible with the On/Off switch. The further you press the switch, the higher the speed of the battery-powered drill/screwdriver in accordance with whichever gear has been selected.

Screwdriving

We recommend using self-centering screws (e.g. Torx screws, recessed head screws) designed for reliable working. Be sure to use a bit that matches the screw in shape and size. Set the torque, as described elsewhere in these operating instructions, to suit the size of screw.

GB

Technical data

Voltage supply 24 V =

Speed 0-360 / 0-1100 rpm

Torque 10 levels

Forward and

reverse rotation yes

Chuck clamping

width 2 - 13 mm

Battery charging

voltage 24 V =

Battery charging

current 2.5 A

Mains voltage for

charger 230 V \~ 50 Hz

Sound pressure level

LPA: 85.2 dB(A)

Sound power level

LWA: 98,2 dB(A)

Vibration a_w <2.5 m/s ^2

Weigth: 5,4 kg

Old and defective batteries do not belong in the refuse bin. Think of the environment! Cadmium is toxic. For correct disposal, return old and defective batteries postage-paid to ISC or take them to your local old battery depot. Ask at your town hall for details of the old battery depots in your area.

Ordering replacement parts

Please quote the following data when ordering replacement parts:

● Type of machine
● Article number of the machine
● Identification number of the
● Replacement part number of the part required

F

EC Declaration of Conformity

© Declaration de Conformità CE

HL EC Conformittelssverklaring

The undergrained declarations in the name of the company that the product is in compliance with the following guidelines and standards.

which is called a film of classic American.

We have a plan, a cell - 32400 x 100% of the 100% of the 100% of the 100% of the 100% of the 100% of the 100% of the 100% of the 100% of the 100% of the 100% of the 100% of the 100% of the 100% of the 100% of the 50% of the 50% of the 50% of the 50% of the 50% of the 50% of the 50% of the 50% of the 50% of the 50% of the 50% of the 50% of the 50% of the 50% of the 50% of the 50% of the 50% of

Technical changes subject to change

The guarantee period begins on the sales date and is

valid for 5 years.

Responsibility is assumed for faulty construction or

material of functional defects.

Any necessary replacement parts an necessary repair

work are free of charge

We do not assume responsibility for consequential

damage.

Your customer service partner

TAKUUTODISTUS

©Euban international

Schreibholstraße 19

CH-8405 Winterthur

Tel [phone], Fax [phone]

① Global UK Ltd

Morpelb Wharf

Twelve Quays

Birkenhead, Wirral

CH 41 1NG

Tel. [phone], Fax [phone]

⑤ Commercial Environmental

Commercial Eimer S.A. Antonio Gahaner, N.

Aldardo Gedezón N° 85 Plante 36 E-28024 Euopaccal Madrid

Tel: [phone], Fax: [phone]

P. Einball Herba

Bue de Adelaide, 225

P-4405-017 Arcozalo VNG

Tel. [phone] Fax [phone]

① Einball Italia e r.l.

106 Heronl 15

L22070 Borosette (Co)

Tel: [phone] Fax: 07

1. 04: 9:00 AM, 14:30 PM

DK Einheit Skandinava

⑤ Вагосовий 36

DK-8600 Silkeborg

Tel. [phone]. Fax [phone]

Sankralin Hany OY

Konzernkalu 5

FIN-S3840 Tampere

Tel. [phone] Fax [phone]

PL Einbel Polska sp. Z.o.g.

UL Miedzyleska

PL-50-554 Wroclaw

Tel. [phone]. Fax [phone]

H Einbel Hungary Ltd

Vaida Peter u. 12

H 1089 Budapest

Tel. [phone], Fax [phone]

TR Comsk

makina licaral ve saravi lld. sli

Alay-Cesra Mah, Yarapan Sck, No. 19

TB 34843 Maltepr - Istanbul

Tel. [phone]. Fax [phone]

(RO) Neurotech S.P.

Hof Lappa, Genzyme (14, 29)

Bd.Laser Catalog 2 S.C. AAn. 9 Sector

PO 75 121 Buskors

RO 15 121 Bucharest Tel: [phone] Fax: [phone]

1. Fries, Biv. E.P.O

-004 PDS S.A.D.

Area 100

07 19915 Pach - Postwater 011

CZ-19011 Prana - Bechovice 911 Tel: +Fax [phone]

161.41 2x 82573 10264

© Einbel Bulgarica

34 A Solan Shampley St

Anl. 4

BG 9000 Yarna

Tel. [phone], Fax [phone]

⑤ Luwa Trawrod No.

Lithiarko 29

810-4000 Кроп

Tel: [phone] Fax: [phone]

(1) Einbe) Crevis d.o.

Veika Ves 2

HR 49224 L

Tel [phone] Fax [phone]

YU MP Trading d.o.o.

Cka Liubira BIV

YU 11000 Beograd

GR An Mawaldogruos S A

Technical & Commercial company

1. Papastalou & Askipiou Sir.

GB 18545 Piräus

Tel [phone]. Fax [phone]

⑪ Betnas

Alluvovskovo stresse, 25

BUS 127273 Moscow

Tel: [phone], Fax: [phone]

EH 02/2003