TE206XF1 - Deep fryer BRANDT - Free user manual and instructions

Brand	BRANDT
Model	TE206XF1
Product type	Built-in electric deep fryer
Power supply	230 V ~ 50 Hz
Power	2300 W
Oil capacity	2.0 to 2.7 liters
Temperature range	40 °C to 220 °C
Safety thermostat	Yes, integrated
Recommended oil type	Vegetable oils for deep frying (except sunflower and blends)
Power cord	H05RR-F / H05RN-F (3×1.5 mm²)
Installation	Built into a worktop
Dimensions (L x W x H)	Not provided, approx. 40 x 30 x 20 cm (estimate)
Weight	Not provided, approx. 8 kg (estimate)
Indicator lights	General power and heating
Cleaning	Steel and heating element: non-abrasive products, avoid chlorine and acids
Maintenance	Filter oil regularly, change often
Repairability	Safety thermostat accessible after removing the oil tank

Frequently Asked Questions - TE206XF1 BRANDT

What is the oil capacity of the TE206XF1 deep fryer?

The BRANDT TE206XF1 deep fryer accepts between 2.0 and 2.7 liters of oil. The minimum and maximum levels are indicated by two notches on the wall of the tank.

What type of oil should be used in this deep fryer?

Use exclusively vegetable oils suitable for deep frying. Avoid mixed seed oils and sunflower oil, which are not recommended by the manufacturer.

How to turn on the TE206XF1 deep fryer?

Turn the control knob on the front to select the temperature between 40 °C and 220 °C. A general indicator light stays on when operating, and a heating indicator light turns off when the temperature is reached.

What to do if the deep fryer stops heating?

First check the safety thermostat. Unplug the appliance, remove the oil tank, unscrew the protective cap on the inner front wall, then press the thermostat reset button.

How to clean the deep fryer?

Always unplug the appliance before cleaning. Clean the steel parts and the heating element with non-abrasive products, without chlorine (bleach) or acidic substances (vinegar, lemon).

Can I fry frozen foods?

Yes, but it is recommended to thaw them at low temperature first, then fry at high temperature. Make sure the foods are well dried before immersing them in oil.

How to optimize cooking of fries?

For perfect fries, do a pre-cook at 160 °C then a final cook at 180 °C. This yields a crispy and golden result.

Does the deep fryer need to be built-in?

Yes, this model is designed to be built into a worktop. Follow the installation instructions provided and call a professional for the electrical connection.

What is the electrical power of the TE206XF1?

The deep fryer has a power of 2300 W and a 230 V supply. The power cord is type H05RR-F or H05RN-F (3×1.5 mm²).

How to change the oil of the deep fryer?

The oil can be reused several times if filtered between each use. To change it, remove the used oil, clean the tank, and pour new oil between the min and max marks.

USER MANUAL TE206XF1 BRANDT

The manufacturer declines all responsibility for possible inaccuracies contained in this pamphlet, due to printing or copying errors. We reserve the right to make on our own products those changes to be considered necessary or useful, without jeopardizing the essential characteristics.

FRYER operating instructions

THIS APPLIANCE IS CONCEIVED FOR DOMESTIC USE ONLY. THE MANUFACTURER SHALL NOT IN ANY WAY BE HELD RESPONSIBLE FOR WHATEVER INJURIES OR DAMAGES ARE CAUSED BY INCORRECT INSTALLATION OR BY UNSUITABLE, WRONG OR ABSURD USE.

CE PRODUIT EST CONÇU EXCLUSIVÉMENT POUR USAGE DOMESTIQUE. LE CONSTRUCTEUR DÉCLINE TOUTE RESPONSABILITÉ POUR DOMMAGES ET BLESSURES CAUSES PAR UNE INSTALLATION INCORRECTE OU PAR UN USAGE IMPROPRE, ERRONÉ OU ABSURDE.

We would like to congratulate you on the choice you have made.

This new product, carefully designed and constructed from materials of the highest quality, has been carefully tested so as to be able to meet all your requirements for perfect cooking.

We would ask you, nevertheless, to read and follow the simple instructions that will allow you to obtain excellent results right from the beginning.

With this up-to-date apparatus, we would like to wish you every success.

THE MANUFACTURER

CONTENTS

Instructions for the user

Installation 6

Use 6

Maintenance 7

Instructions for the installationist

Installation 8

Positioning 8

Electrical connections 8

Technical data

Power supply 230V

Power 2300W

Supply cable H05RR-F (3x1,5 sq. mm)

H05RN-F (3x1,5 sq. mm)

Instructions for the user

Installation

All the operations relating to the installation (electrical connection) must be carried out by qualified personnel according to the regulations in force.

Use

(Fig. 1) The apparatus is switched on by turning the control knob on the front that allows a temperature to be set from 40 to 200^ .

A signal light comes on to show that the resistance is operating, and when it goes off it shows that it has reached the required temperature.

A second (general) light always stays on when the apparatus is operating. The fryer is equipped with a thermostat that constantly maintains the temperature of the oil bath. Furthermore, a safety thermostat automatically goes into operation in case of faulty working of the main thermostat, preventing the oil from reaching too high a temperature, about 220^ .

The use of this equipment is very simple, however, to obtain the best results, it is advisable to follow these instructions:

• before putting oil in for the first time, carefully clean the steel parts and the resistance, so as to remove any residue left from manufacture.

• Never turn on the apparatus with the resistance turned out of the bowl.

• Never turn on the apparatus unless there is oil in the bowl.

• Always use vegetable oil suitable for frying: we do not recommend oil from assorted seeds or sunflower.

• The quantity of oil contained in the bowl varies from a minimum of 2 litres to a maximum of 2,7 litres. If, during use, the oil level should drop below the minimum, fresh oil must be added.

It is advisable to add oil of the same type. The minimum and maximum levels are shown by two marks cut into the vertical side of the bowl.

• The oil can be used several times, but we recommend it is filtered between one cooking and the next, so as to eliminate deposits which can occur.

• It is best to change the oil very often, however, because, even if it is well filtered, small residual particles can catch fire during cooking.

• Before putting the food into the fryer, check that is perfectly dry.

Wait until the oil has reached the required temperature.

• For frozen food, it is advisable to defrost it at a low temperature and then fry it at high temperature.

• In preparing certain dishes (fried potatoes) you will get the best results by precooking at a temperature of 160^ , and then subsequently cooking at 180^ .

• During cooking, it is often necessary to add salt or flavourings. Avoid, if at all possible, doing this directly into the fryer, because salt, by falling into the oil, has its quality reduced.

• In the case of a breakdown, before calling a technician, try resetting the safety thermostat, by pressing the button visible, after having removed the oil bowl and unscrewed the safety plug on the front, interior side.

Maintenance

Before doing any operation, cut off the electricity from the apparatus.

In order to give your equipment a long life, it is vital to thoroughly clean it all over, remembering the following points:

• the steel and/or painted parts must be cleaned using suitable products (available on the market) which are not abrasive or corrosive. Avoid products based on chlorine (bleach, etc);

• avoid leaving acids or alkalis on the work surface (vinegar, salt, lemon-juice, etc.)

Instructions for the installationist

Installation

These instructions are intended to be used by a qualified installationist, who will be responsible for the installation, adjustment and maintenance according to the laws and regulations in force.

All operations must always be carried out with the equipment disconnected from the electricity.

Positioning

(Fig. 2) The apparatus is designed to be set into a work surface, as shown in the relevant illustration.

Fit the seal provided round the whole perimeter of the surface.

Electric connections

Before connecting up the electricity, ensure that:

• the specification of the system is such as to match that shown on the serial number plate applied to the underneath of the work surface.

• the system is supplied with an efficient earth connection to the ground, according to the regulations and the laws in force. The earth connection is obligatory by law.

In the case where the equipment is not supplied with cable and/or relevant plug, make use of materials suited to the input current shown on the serial number plate, and to the working temperature. The cable must not reach a temperature of more than 50^ higher than the ambient temperature in any part of its length.

In order to connect directly to the mains supply, it is necessary to insert a multipolar switch with a minimum aperture between contacts of 3mm of a size suitable for the load marked on the plate, and conforming to the regulations in force (the yellow and green earth cable must not be turned off by the switch). The plug or multipolar switch must be easily reached with the equipment installed in position.

N.B.: The manufacturer declines any responsibility in the case where the above and the normal accident prevention regulations have not been respected.

Cher Client,