60.2551.01 - Alarm clock radio TFA - Free user manual and instructions

USER MANUAL 60.2551.01 TFA

ELLYPSE – Radio-controlled alarm clock with USB charging function

Thank you for choosing this instrument from TFA.

1. Before you use this product

• Please make sure you read the instruction manual carefully. This information will help you to familiarize yourself with your new device, to learn all of its functions and parts, to find out important details about its first use and how to operate it and to get advice in the event of a malfunction.

• Following and respecting the instructions in your manual will prevent damage to your instrument and loss of your statutory rights arising from defects due to incorrect use.

• We shall not be liable for any damage occurring as a result of non following of these instructions.

• Please take particular note of the safety advice!

• Please keep this instruction manual safe for future reference.

3. Range of application and all the benefits of your new instrument at a glance

• With time zone and manual setting option ELLYPSE – Radio-controlled alarm clock with USB charging function

• Brightness and alarm volume can be adjusted continuously

• Charging function for mobile devices via USB port (1A)

• This product is exclusively intended for the range of application described above. It should only be used as described within these instructions.

• Unauthorized repairs, alterations or changes to the product are prohibited. Caution! Risk of electrocution!

• Plug the device only into a mains socket installed within electrical safety regulations and with a 240V mains voltage!

• The mains socket must be located near the equipment and it must be easily accessible.

• The device and the power adapter must not come into contact with water or moisture. Only suitable for indoor use.

• Do not use the device if the housing or the power adapter are damaged.

• Keep the device out of reach of persons (including children) who cannot fully appreciate the potential risks of handling electrical equipment.

ELLYPSE – Radio-controlled alarm clock with USB charging function

• Only use the supplied power adapter.

• Route the mains cable so it does not come into contact with sharp-edged or hot objects. Caution! Risk of injury:

• Keep this instrument and the batteries out of reach of children.

• Batteries contain harmful acids and may be hazardous if swallowed. If a battery is swallowed, this can lead to serious internal burns and death within two hours. If you suspect a battery could have been swallowed or otherwise caught in the body, seek medical help immediately.

• Batteries must not be thrown into a fire, short-circuited, taken apart or recharged. Risk of explosion!

• Low batteries should be changed as soon as possible to prevent damage caused by leaking. Never use a combination of old and new batteries together, nor batteries of different types. Wear chemical-resistant protective gloves and safety glasses when handling leaking batteries. Important information on product safety!

• Do not expose the device to extreme temperatures, vibrations or shocks. ELLYPSE – Radio-controlled alarm clock with USB charging function

ELLYPSE – Radio-controlled alarm clock with USB charging function

• Remove the protective film from the display.

• Insert the power adapter pin into the device jack and connect the plug to a wall socket.

• Important! Make sure that your household voltage is no more than 240V! Otherwise your device may be damaged.

• The device is ready for use. All segments will be displayed for about 2 seconds

• Open the battery compartment and insert two new AAA 1.5 V batteries, polarity as illustrated.

• Close the battery compartment again.

• The device only works with the power adapter. The batteries will operate as a backup power source in case of power failure.

6.1 Radio-controlled time reception

• The clock will now scan the DCF frequency signal and the DCF symbol will be flashing on the display. When the time code is successfully received after 3-8 minutes, the radio-controlled time and the DCF symbol will be shown steadily on the display.

• To avoid interference, the display light becomes weak during the reception of the radio controlled clock and the USB port turns off.

• The DCF reception always takes place at 2:00 in the morning. If the reception is not successfully received, further attempts will be taken at 3:00 and 4:00 o'clock.

• You can also start the initialization manually. ELLYPSE – Radio-controlled alarm clock with USB charging function

• Press and hold the UP button for three seconds.

• The clock will now scan the DCF frequency signal and the DCF symbol will be flashing on the display.

• To end the DCF reception attempt, press the UP button again. The DCF reception symbol disappears.

• There are three different reception states: flashing – reception is active solid – reception is very good no symbol – no DCF reception

• If the clock cannot detect the DCF-signal (e.g. due to interference, transmitting distance, etc.), the time can be set manually.

• The clock will then work as a normal quartz clock. (see: Manual settings). Note on radio-controlled time The time base for the radio-controlled time is a caesium atomic clock operated by the Physikalisch Technische Bundes- anstalt based in Braunschweig (Brunswick), Germany. It has a time deviation of less than one second in one million years. The time is coded and transmitted from Mainflingen near Frankfurt via the frequency signal DCF-77 (77.5 kHz) and has a transmitting range of approximately 1,500 km. The adjustment to Daylight Saving Time (summer/winter time) is automatic. In Daylight Saving Time DST is shown on the display . The reception quality depends mainly on geographic location. Nor- mally there should be no reception problems within a 1,500 km radius around Frankfurt. TFA_No. 60.2551_Anleitung 21.08.2018 15:59 Uhr Seite 13– 26 – – 27 –

ELLYPSE – Radio-controlled alarm clock with USB charging function

Therefore, please note the following steps:

• The recommended distance to any interfering sources like computer screens or TV sets is at least 1.5 - 2 meters.

• Within concrete walls (reinforced with steel) such as basements, the received signal is naturally weakened. In extreme cases, please place the unit close to a window to improve reception.

• During night-time, the atmospheric interference is usually less severe and reception is possible in most cases. A single daily reception is adequate to keep the accuracy deviation under 1 second.

• Important: The device cannot be operated during the DCF time-signal reception.

• Press and hold the UP or DOWN button in setting mode for fast mode.

• The device will automatically quit the setting mode if no button is pressed for 20 seconds.

• Press and hold the MODE button in normal mode for three seconds.

• The time zone (00 - default) will be flashing. Press the UP or DOWN button to make the time zone correction (+1/-1).

• The time zone correction is needed for countries where the DCF signal can be received but the time zone is different from the DCF time (e.g. +1=one hour plus).

• Press the MODE button again and you can adjust the hours and the minutes with the UP or DOWN button. ELLYPSE – Radio-controlled alarm clock with USB charging function

• Confirm the setting with the MODE button.

• The manually set time is overwritten once the DCF time signal is successfully received.

7.1.2 12 and 24 hours display

• Press DOWN button in normal mode to choose 12 HR or 24 HR system.

• In 12 HR system PM appears after 12 h on the display.

• Press the MODE button in normal mode to enter the alarm mode.

• AL and 06:00 (default) or the last adjusted alarm time appear on the display.

• Press and hold the MODE button for three seconds to enter the setting mode.

• The alarm symbol will appear on the display and the alarm is activated. The hour digits flash.

• Press the UP or DOWN button to set the desired time.

• Confirm with the MODE button.

• Set the minutes in the same way.

• Confirm with the MODE button.

ELLYPSE – Radio-controlled alarm clock with USB charging function

• Confirm with the MODE button.

• To activate and deactivate the alarm function press the AL button in normal mode.

• The alarm symbol appears/disappears on the display.

• When the alarm is activated, the alarm starts to ring when the set alarm time is reached.

• Press any button (except SNOOZE) and the alarm will stop.

• If the alarm is not stopped manually, the ascending alarm tone automatically turns off after two minutes and it will be reactivated at the same set time on the following day.

• The alarm symbol remains on the display.

• When the alarm rings, press the SNOOZE sensor button briefly and the snooze function is activated.

• Once the snooze function is activated, the snooze symbol will be flashing on the display.

• The alarm will be interrupted for the set time.

• You can select between 3 levels of brightness with the SNOOZE sensor button (HIGH/LOW/OFF).

• In addition, the brightness can be adjusted continuously to the desired level with the LIGHT dial (on level HIGH and LOW).

• The alarm volume can be adjusted continuously to the desired level with the VOL dial. ELLYPSE – Radio-controlled alarm clock with USB charging function

• Plug the USB cable (not included) into the USB port on the alarm clock and connect the other end to your mobile device. Make sure that the USB charging function is suitable for your mobile device (charging current 1A).

• Do not apply excessive force when connecting a USB cable. The USB plug fits only one way into the USB port.

8. Care and maintenance

• Clean the device with a soft damp cloth. Do not use solvents or scouring agents.

• Remove the batteries if the device will not be used for an extended period of time.

• Keep the device in a dry place.

8.1 Battery replacement

• Open the battery compartment and insert two new AAA 1.5 V batteries, polarity as illustrated.

• Close the battery compartment again.

ELLYPSE – Radio-controlled alarm clock with USB charging function

➜ Wait for the DCF signal reception ➜ Set brightness with the SNOOZE sensor button and LIGHT dial No DCF reception ➜ Press and hold the UP button in normal mode for three seconds ➜ Wait for an attempt reception during the night ➜ Change the location (interference!) ➜ Restart the device according to the manual ➜ Set the clock manually No charging function ➜ Connect the device to the power adapter ➜ Check the USB port connection ➜ Wait for the DCF signal reception No alarm sound ➜ Increase volume with the VOL dial If your device fails to work despite these measures, contact the retailer where you purchased the product.

This product has been manufactured using high-grade materials and components which can be recycled and reused. Never dispose of empty batteries and rechargeable batteries in ordinary household waste. ELLYPSE – Radio-controlled alarm clock with USB charging function

As a consumer, you are required by law to take them to your retail store or to an appropriate collection site depending on national or local regulations in order to protect the environment. The symbols for the contained heavy metals are: Cd = cadmium, Hg = mercury, Pb = lead This product is labelled in accordance with the EU Waste Electrical and Electronic Equipment Directive (WEEE). Please do not dispose of this product in ordinary household waste. As a consumer, you are required to take end-of-life devices to a designated collection point for the disposal of electrical and electronic equipment, in order to ensure environmentally-compatible disposal.

ELLYPSE – Radio-controlled alarm clock with USB charging function

Housing dimension 136 x 85 x 55 mm Weight 149 g (device only) No part of this manual may be reproduced without written consent of TFA Dostmann. The technical data are correct at the time of going to print and may change without prior notice. The latest technical data and information about this product can be found in our homepage by simply entering the product number in the search box. EU Declaration of conformity Hereby, TFA Dostmann declares that the radio equipment type 60.2551 is in compliance with Directive 2014/53/EU. The full text of the EU decla- ration of conformity is available at the following Internet address: www.tfa-dostmann.de E-Mail: [e-mail] TFA Dostmann GmbH & Co.KG, Zum Ottersberg 12, D-97877 Wertheim, Germany 08/18 ELLYPSE – Réveil radio-piloté avec fonction de chargement USB