60.2027.01 - Alarm clock radio TFA - Free user manual and instructions

USER MANUAL 60.2027.01 TFA

Digital alarm clock with LED digits

Thank you for choosing this instrument from TFA.

1. Before you use this product

• Please make sure you read the instruction manual carefully.
• Following and respecting the instructions in your manual will prevent damage to your instrument and loss of your statutory rights arising from defects due to incorrect use.
• We shall not be liable for any damage occurring as a result of non-following of these instructions.
• Please take particular note of the safety advice!
• Please keep this instruction manual safe for future reference.

2. Delivery contents

• Digital alarm clock
• DC 5V USB cable and power adaptor
- Instruction manual

3. Range of application and all the benefits of your new Instrument at a glance

• Display of time or indoor temperature, automatic change is adjustable
• Alarm with snooze function
  • LED digits with 3 brightness levels
• Dimming function with automatic timer

Digital alarm clock with LED digits

4. For your safety

• This product is exclusively intended for the range of application described above. It should only be used as described within these instructions.
• Unauthorized repairs, alterations or changes to the product are prohibited.

Caution!

Risk of electrocution!

• Connect the device using the USB cable and the supplied power supply to a mains socket installed within your country's electrical safety regulations and with a correct mains voltage (see nameplate).
• The mains socket must be located near the equipment and it must be easily accessible.
• Unplug the device immediately if any fault occurs.
• The device and the power adapter must not come into contact with water or moisture. Only suitable for indoor use.
• Do not use the device if the housing, the USB cable or the power adaptor are damaged.
• Operate the device out of reach of persons (including children) who cannot fully appreciate the potential risks of handling electrical equipment.
• Connect the USB cable to the device and the power adaptor first and then plug the power adapter into the socket.

Digital alarm clock with LED digits

• Route the USB cable lead so that it does not come into contact with sharp-edged or hot objects.
• Only use the supplied power adapter or connect the device via the USB cable to a suitable USB power source such as a computer, notebook.

Caution! Isk of Injury!

• Keep this instrument and the batteries out of reach of children.
• Batteries contain harmful acids and may be hazardous if swallowed. If a battery is swallowed, this can lead to serious internal burns and death within two hours. If you suspect a battery could have been swallowed or otherwise caught in the body, seek medical help immediately.
• Batteries must not be thrown into a fire, short-circuited, taken apart or recharged. Risk of explosion!
• Low batteries should be changed as soon as possible to prevent damage caused by leaking. Never use a combination of old and new batteries together, nor batteries of different types.
• Wear chemical-resistant protective gloves and safety glasses when handling leaking batteries.

Important information on product safety!

- Do not expose the device to extreme temperatures, vibrations or shocks.

Digital alarm clock with LED digits

5. Elements

A: Display (Fig. 1):

A 1: Alarm symbol A 2: Snooze symbol

A 3: Time/indoor temperature/alarm time

B: Buttons (Fig. 2):

B 1: TIME button B 2: ALARM button

B 3: SNOOZE sensor button B 4: + button

B 5: - button B 6: ALARM ON/OFF switch

B 7: RESET button

C: Housing (Fig. 2):

C 1: Battery compartment C 2: DC 5V jack

6. Getting started

- The alarm clock can be operated with 3 x 1,5 V AAA batteries (not included). The batteries maintain the clock operation in the event of blackout or other power failure. In pure battery operation, the display is activated for 10 seconds each time a button is pressed. Continuous illumination of the display only works with USB-/mains connection.

Digital alarm clock with LED digits

• Open the alarm clock's battery compartment. Insert three new AAA 1.5 V batteries, polarity as illustrated. Close the battery compartment.
• For a permanent display light and to save battery life, use the supplied DC 5V USB cable.
• Connect the attached power adapter to the alarm clock. Important! Make sure that your household voltage is no more than 240V! Otherwise your device may be damaged.
• A beep tone is heard and 00:00 appears on the display.
  • The device is ready for use.

7. Settings

• Press and hold the + or - button in setting mode for fast mode.
• The device will automatically quit the setting mode if no button is pressed for 10 seconds.

7.1 Time setting

• Press and hold the TIME button in normal mode for three seconds.
• The hour digit will be flashing. Press the + or - button to adjust hours.
• Confirm the setting with the TIME button.
• Set the minutes in the same way.
• Confirm with the TIME button.

Digital alarm clock with LED digits

7.2 Alarm time setting

• Press the ALARM button in normal mode, to show the alarm time. The alarm symbol flashes.
• Press and hold the ALARM button for 3 seconds.
• 6:00 (default) or the last adjusted alarm time appear on the display.
• The alarm symbol and the hour digit are flashing. Press the + or - button to set the hours.
• Confirm the setting with the ALARM button.
• Set the minutes in the same way.
• Confirm the setting with the ALARM button. The display shows the current time.
• To activate/deactivate the alarm function, move the ALARM ON/OFF switch to ON or OFF.
  • The alarm symbol appears/disappears on the display.
• When the alarm is activated, the alarm starts to ring when the set alarm time is reached.
• Press any button (except SN00ZE) and the alarm will stop.
• If the alarm is not stopped manually, the alarm tone automatically turns off after one minute and will be reactivated at the same set time in the following day.
  • The alarm symbol remains on the display.
• When the alarm rings, press the SNOOZE sensor button briefly and the snooze function is activated. The snooze symbol flashes on the display.
  • The alarm will be interrupted for 5 minutes.
• Press any button (except SNOOZE) and the snooze function will stop.

Digital alarm clock with LED digits

8. Display mode

- Each press on the TIME button in normal mode will change the display between: Time, indoor temperature and automatic dimming function OFF/ON.

8.1 Automatic display change

• Use the TIME button to select the time or temperature display.
• Press the + button for 3 seconds. LOOP appears on the display.
  • Time and date appear in sequence (temperature 5 s -> time 10 s).
• Press and hold the + button for 3 seconds to return to the time display.

8.2 Automatic dimming mode

• Select the automatic dimming function OFF/ON by pressing the TIME button.
• By default, the automatic dimming function is disabled (OFF)
• To activate (ON) or deactivate (OFF) the function press the + or - button.
• If the auto dimming mode is activated (ON), the weak backlight turns on automatically at 6 pm and switches off again at 6 am (default setting).

8.2.1 Setting time Interval

• Press and hold the TIME button (display ON) to enter the setting mode for the automatic timer.
• The start time flashes. Press the + or - button to set the hours.

Digital alarm clock with LED digits

• Confirm the setting with the TIME button and press the + or - button to set minutes.
• Confirm the setting with the TIME button and set the end time in the same way.
• Confirm the setting with the TIME button.
• If the auto dimming mode is activated (ON), the weak backlight turns on automatically for the set time.

9. Display light

- USB-/mains connection:

The display illumination works in continuous operation. Press the + button to adjust the brightness in 3 levels or to switch it off.

- Battery operation and backlight switched off with USB-/mains connection:

Press any button. The display turns on for 10 seconds.

10. Care and maintenance

• Clean the instrument with a soft damp cloth. Do not use solvents or scouring agents.
• Unplug the device and remove the batteries if the device will not be used for an extended period of time.
• Store the device in a dry place.

Digital alarm clock with LED digits

10.1 Battery replacement

- Change the batteries 3 × 1.5 V AAA when the illumination without USB-/mains connection gets weak.

11. Trouble shooting

Problem Solution

No display Operation with USB-/mains connection:

→ Connect the device with the USB cable to a suitable power source
→ Check the connection
→ Press any button to activate the display briefly
→ Set the brightness with the + button

Battery operation:

→ Ensure the batteries' polarities are correct
→ Change the batteries
→ Press any button to activate the display briefly

Digital alarm clock with LED digits

Incorrect indication Press the RESET button using a pin

Battery operation:

→ Change the batteries

If your device falls to work despite these measures, contact the retailer where you purchased the product.

12. Waste disposal

This product has been manufactured using high-grade materials and components which can be recycled and reused.

Never dispose of empty batteries and rechargeable batteries with ordinary household waste.

As a consumer, you are required by law to take them to your retail store or to an appropriate collection site depending on national or local regulations in order to protect the environment.

The symbols for the contained heavy metals are: Cd = cadmium, Hg = mercury, Pb = lead

This product is labelled in accordance with the EU Waste Electrical and Electronic Equipment Directive (WEEE).

Digital alarm clock with LED digits

Please do not dispose of this product in ordinary household waste. As a consumer, you are required to take end-of-life devices to a designated collection point for the disposal of electrical and electronic equipment, in order to ensure environmentally-compatible disposal.

1. Specifications

Measuring rangeTemperature 0 °C...+50°C
Power consumption DC 5V USB cable with power supply (included)
	Input: 100-240V AC 50/60Hz 0.3A MaxOutput: 5.0V DC 0.6A, 3.0WAverage active efficiency: ≥ 69.64%No-load power consumption: ≤ 0.10 W3 x AAA 1.5 V batteries (not included)Use alkaline batteries

Dimensions 178 x 36 x 84 mm

Weight 214 g (device only)

Digital alarm clock with LED digits

No part of this manual may be reproduced without written consent of TFA Dostmann. The technical data are correct at the time of going to print and may change without prior notice.

The latest technical data and information about this product can be found in our homepage by simply entering the product number in the search box.

www.tfa-dostmann.de

Piles 3 x 1.5 V AAA (non incluses)