Duolab LV5033 - Uncategorized ROWENTA - Free user manual and instructions

USER MANUAL Duolab LV5033 ROWENTA

A pioneer in customised, preservative-free facial treatment, DUOLAB allows you to meet the changing needs of your skin by combining the benets of an hydrating base and a targeted concentrate. ROWENTA experts have designed the unique formulator heat-controlled system. The treatment delivered at the ideal temperature, boosts the benets of your cream by increasing well-being and sensoriality experience. The innovation is combined with ultra-concentrated formulae rich in natural ingredients; they are fully hermetically encapsulated to guarantee optimal protection. This personalised care ritual allows you to receive a highly eective and targeted at home treatment to suit any skin type.

Non-contractual picture3736

- For your safety, this appliance complies with the applicable standards and regulations (Low Voltage Directive, Electromagnetic Compatibility, Environmental…). - As an additional safety measure, we recommend the installation of a residual current dierence device in the electrical circuit supplying the bathroom, acting at not more than 30 mA. Ask your installer for advice.

• CAUTION: Never use your appliance with wet hands or near water contained in bath tubs, showers, sinks or other containers…

• Do not use this appliance near bathtubs, showers, basins or other vessels containing water.

• When using the appliance in the bathroom, unplug it after use as the presence of water nearby may pose a danger even when the appliance is turned o. The appliance will not work while it is connected to the mains power supply.

• For countries subject to EU regulations ( ) : This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

• The battery must be removed from the appliance before it is scrapped. The appliance must be disconnected from the supply mains when removing the battery. The battery is to be disposed of safely.

• WARNING: Keep the appliance in a dry place 1 Dispenser A Opening for capsule 1 insertion B Opening for capsule 2 insertion C Lateral guide for insertion into the base D Flexible pressure area for dispensing the cream 2 Formulator E Control panel F Dispenser positioning area G Battery indicator H On/o button I Dispenser release button J Illuminated ring 3 K Base treatment capsule (1) L Active treatment capsule (2) **Capsules not included** 4 Transformer plug M Transformer plug N Removable connectors

• Do not use at temperatures below 15°C and above 35°C.

• When assembling the accessories, make sure you properly lock them into place in their compartment.

• This appliance is intended for domestic use only.

• It cannot be used for professional purposes.

• The guarantee shall become null and void if the appliance is used incorrectly.

• Should you need any additional information, in case of problems or simply to seek advice, please contact your Duolab customer care.

• Contact details of your Duolab customer care can be found at www.duolab.com

• Always disconnect the appliance once fully charged, before cleaning or in the event of an operational issue.

• Do not clean with abrasive or corrosive products.

• Do not submerge it or run it under water, even to clean it

• Do not clean the product or the dispenser by running it under water.

• Clean the product with a damp cloth after use.

• Do not put the appliance in the dishwasher.

• Do not wet the adaptor. Flashing battery indicator You have enough battery for 1 treatment. Charge your treatment formulator as soon as possible Battery indicator ashes 3 times and then goes o. Your treatment formulator is out of battery. Charge it. A 5 minutes charge will allow you to carry out 1 treatment. Battery indicator o Your treatment formulator is charged If you drop your appliance and it does not work normally, do not use it and contact an Authorized Service Centre.

• For other countries not subject to EU regulations : This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

• This appliance contains batteries that are only replaceable by skilled persons.

• WARNING : Detachable supply unit : For the purposes of recharging the battery, only use the detachable supply unit ZD12D100100 provided with this appliance.

If the pins of the plug parts are damaged, the plug-in power supply shall be scrapped.

• The external exible cable or cord of this transformer cannot be replaced; if the cord is damaged or does not work, the transformer shall be scrapped.

• Withdrawal of batteries: Before removing the Li-ion batteries, discharge them completely. Open the batteries compartment using a tool, cut all the connections and then recycle the batteries in a safe manner.

• Contact details of your Duolab customer care can be found at www.duolab.com.

• Always disconnect the appliance once fully charged, before cleaning or in the event of an operational issue.

• Do not use with consumables other than those designed especially for the appliance.

• Unplug the appliance once the battery is fully charged.

• Do not hold with damp hands.

• Ensure that the appliance that you use is in accordance with the electrical network in the country of use.

• Do not unplug it by pulling on the cord, but by pulling out the plug.

• Do not use an extension cord.

• Do not get the adaptor wet.

• Do not use the appliance if an accessory, cord or the appliance itself is damaged.

• These instructions are also available on website www.duolab.com4948

7. ENVIRONMENTAL RESPONSIBILITY

Let’s help protect the environment Your appliance is designed to work for many years. But when you decide to replace it, don’t forget to think about how you can help to protect the environment by allowing it to be reused, recycled or recovered in some other way. This will prevent any harmful impact on the environment or on human health due to the uncontrolled disposal of waste that can contain dangerous substances. This label indicates that this product must not be disposed of with household waste. Take it to a collection point, to the distributor when buying a new equivalent product, or an approved service centre for processing. Before disposing of the appliance, remove the battery and dispose of it in accordance with the regulations and local arrangements. If you have any questions, contact the DUOLAB customer service. DUOLAB promotes the collection of used capsules.

1. Remove your capsules by gently pulling capsule 2 out of the dispenser.

There’s no need to open the dispenser to do this.

2. Keep your capsules in your recycling bin.

3. Once your bin is full, recycle your capsules. You can find more information

on the ocial Duolab website for your region. YOUR CREAM SPILLS AND SPREADS IN THE APPLIANCE:

• Check that the capsules have been inserted correctly in their cases.

• Check that the capsule tip has not been folded on insertion. Replace your capsules, ensuring that the tip does not fold on insertion.

• Check that you have not pressed the exible parts of the dispenser when removing it from the appliance. Pull the dispenser by holding onto the rigid upper part.

• Make sure you have properly put the two capsules in the dispenser before starting the mixing cycle. THERE IS NO CREAM WHEN PRESSING THE DISPENSER

• Check that the capsules have been properly inserted, and that the cream has not spilled inside the appliance. Ensure that the capsules are placed properly.

• Check that the capsule end has not been folded on insertion. Replace your capsules, ensuring that the tip does not fold on insertion.

• Check that you have not pressed the exible parts of the holder when removing it from the appliance. Pull the holder by holding onto the rigid upper part.

• Make sure you have properly put the two capsules in the dispenser before starting the kneading cycle. THE KNEADING CYCLE DOES NOT START.

• The ON/OFF button is lit: this is normal, just press the button again to start the cycle

• Check that the product has enough battery to start the cycle. Your product is designed with a safety feature, meaning that the cycle will not start if there is not enough battery to nish it: recharge the battery of your product (see “precautions for use” section for further details).

• The ON/O button is ashing: Check that the dispenser has been properly inserted into its case. The product emits a sound signal when the dispenser is correctly inserted.

• Check that your capsules have been inserted the right way round into the dispenser. Look at the insertion direction indicated by the arrow printed on the capsule.

• If, the dispenser is still not detected, contact your nearest after-sales service YOU FIND SOME TREATMENT UNDER YOUR APPLIANCE.

• Do not place the dispenser into the product with used capsules. The capsules are single use.

• For all other cases, refer to the two rst paragraphs of this section. THE DISPENSER DOES NOT GO INSIDE ITS CASE.

• Check that you have properly removed the transport block from the dispenser upon rst use.

• Ensure that the dispenser has been correctly closed before insertion

• Check that your capsules have been inserted the right way round into dispenser. Look at the insertion direction indicated by the arrow printed on the capsule.. YOU CANNOT REMOVE THE DISPENSER AT THE END OF THE CYCLE.

• Contact your nearest after-sales service. ONE OF THE CAPSULES REMAINS IN THE DISPENSER WHEN REMOVING IT.

• Remove the remaining capsule using a suitable tool. Refer to the above section on the removal of capsules. YOUR PRODUCT IS IN SAFE MODE REPETITIVE AUDIBLE SIGNAL AND RAPID FLASHING OF THE BASE.

• In case your appliance is in safety mode, apply the reset process: hold down the two buttons H and I for 5 seconds. If the problem persists, contact an Authorised Service Centre.

• If your appliance goes into safety mode, do not use the capsules and the cosmetic in the dispenser: use new capsules if you restart a new cycle. WHEN INSERTING THE DISPENSER, THE “PADLOCK” BUTTON LIGHTS UP, AND IT IS NOT POSSIBLE TO START A CYCLE:

• You cannot perform a cycle shortly after a rst one. Wait for the “padlock” button to go o to restart a cycle.5150

• Never use while sleeping.

• Never drop or insert any object into any opening or hose.

• Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.

• Fill (reservoir) with water only. Do not overll (or specify lling instructions).

• Use with DUOLAB lotion capsules only

• Withdrawal of batteries: Before removing the Li-ion batteries, discharge them completely. Open the batteries compartment using a tool, cut all the connections and then recycle the batteries in a safe manner.

• Contact details of your Duolab customer care can be found at www.duolab.com.

• Always disconnect the appliance once fully charged, before cleaning or in the event of an operational issue.

• Do not use with consumables other than those designed especially for the appliance.

• Unplug the appliance once the battery is fully charged.

• Do not hold with damp hands.

• Ensure that the appliance that you use is in accordance with the electrical network in the country of use.

• Do not unplug it by pulling on the cord, but by pulling out the plug.

• Do not use an extension cord.

• Do not get the adaptor wet.

• Do not use the appliance if an accessory, cord, or the appliance itself is damaged.

• These instructions are also available on website www.duolab.com

SAVE THESE INSTRUCTIONS

- When using electrical appliances, especially when children are present, basic safety precautions should always be followed, including the following:

DANGER – To reduce the risk of electrocution:

• Always unplug this appliance immediately after using.

• Do not use while bathing.

• Do not place or store appliance where it can fall or be pulled into a tub or sink.

• Do not place in or drop into water or other liquid.

• Do not reach for an appliance that has fallen into water. Unplug immediately.

• WARNING - To reduce the risk of burns, re, or injury to persons:

• The external exible cable or cord of this transformer cannot be replaced; if the cord is damaged or does not work, the transformer shall be scrapped.

• Close supervision is necessary when this appliance is used by, on, or near children or individuals with certain disabilities.

• Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.

• Never operate this appliance if it has a damaged cord or plug, if it is not working properly, or if it has been dropped, damaged, or dropped into water. Return the appliance to a service center for examination and repair.

• Keep the cord away from heated surfaces. Do not wrap the cord around the appliance.

• Never block the air openings of the appliance or place it on a soft surface, such as a bed or couch, 1 Dispenser A Opening for capsule 1 insertion B Opening for capsule 2 insertion C Lateral guide for insertion into the base D Flexible pressure area for dispensing the cream 2 Formulator E Control panel F Dispenser positioning area G Battery indicator H On/o button I Dispenser release button J Illuminated ring 3 K Base treatment capsule (1) L Active treatment capsule (2) **Capsules not included** 4 Transformer plug M Transformer plug N Removable connectors

• Check that the capsules have been inserted correctly in their cases.

• Check that the capsule tip has not been folded on insertion. Replace your capsules, ensuring that the tip does not fold on insertion.

• Check that you have not pressed the exible parts of the dispenser when removing it from the appliance. Pull the dispenser by holding onto the rigid upper part.

• Make sure you have properly put the two capsules in the dispenser before starting the mixing cycle. THERE IS NO CREAM WHEN PRESSING THE DISPENSER

• Check that the capsules have been properly inserted, and that the cream has not spilled inside the appliance. Ensure that the capsules are placed properly.

• Check that the capsule end has not been folded on insertion. Replace your capsules, ensuring that the tip does not fold on insertion.

• Check that you have not pressed the exible parts of the holder when removing it from the appliance. Pull the holder by holding onto the rigid upper part.

• Make sure you have properly put the two capsules in the dispenser before starting the kneading cycle. THE KNEADING CYCLE DOES NOT START.

• The ON/OFF button is lit: this is normal, just press the button again to start the cycle

• Check that the product has enough battery to start the cycle. Your product is designed with a safety feature, meaning that the cycle will not start if there is not enough battery to nish it: recharge the battery of your product (see “precautions for use” section for further details).

• The ON/O button is ashing: Check that the dispenser has been properly inserted into its case. The product emits a sound signal when the dispenser is correctly inserted.

• Check that your capsules have been inserted the right way round into the dispenser. Look at the insertion direction indicated by the arrow printed on the capsule.

• If, the dispenser is still not detected, contact your nearest after-sales service YOU FIND SOME TREATMENT UNDER YOUR APPLIANCE.

• Do not place the dispenser into the product with used capsules. The capsules are single use.

• For all other cases, refer to the two rst paragraphs of this section. THE DISPENSER DOES NOT GO INSIDE ITS CASE.

• Check that you have properly removed the transport block from the dispenser upon rst use.

• Ensure that the dispenser has been correctly closed before insertion

• Check that your capsules have been inserted the right way round into dispenser. Look at the insertion direction indicated by the arrow printed on the capsule.. YOU CANNOT REMOVE THE DISPENSER AT THE END OF THE CYCLE.

• Contact your nearest after-sales service. ONE OF THE CAPSULES REMAINS IN THE DISPENSER WHEN REMOVING IT.

• Remove the remaining capsule using a suitable tool. Refer to the above section on the removal of capsules. YOUR PRODUCT IS IN SAFE MODE REPETITIVE AUDIBLE SIGNAL AND RAPID FLASHING OF THE BASE.

• In case your appliance is in safety mode, apply the reset process: hold down the two buttons H and I for 5 seconds. If the problem persists, contact an Authorised Service Centre.

• If your appliance goes into safety mode, do not use the capsules and the cosmetic in the dispenser: use new capsules if you restart a new cycle. WHEN INSERTING THE DISPENSER, THE “PADLOCK” BUTTON LIGHTS UP, AND IT IS NOT POSSIBLE TO START A CYCLE:

• You cannot perform a cycle shortly after a rst one. Wait for the “padlock” button to go o to restart a cycle.

• Do not use at temperatures below 15°C and above 35°C.

• When assembling the accessories, make sure you properly lock them into place in their compartment.

• This appliance is intended for domestic use only.

• It cannot be used for professional purposes.

• The guarantee shall become null and void if the appliance is used incorrectly.

• Should you need any additional information, in case of problems or simply to seek advice, please contact your Duolab customer care.

• Contact details of your Duolab customer care can be found at www.duolab.com

• Always disconnect the appliance once fully charged, before cleaning or in the event of an operational issue.

• Do not clean with abrasive or corrosive products.

• Do not submerge it or run it under water, even to clean it

• Do not clean the product or the dispenser by running it under water.

• Clean the product with a damp cloth after use.

• Do not put the appliance in the dishwasher.

• Do not wet the adaptor. Flashing battery indicator You have enough battery for 1 treatment. Charge your treatment formulator as soon as possible Battery indicator ashes 3 times and then goes o. Your treatment formulator is out of battery. Charge it. A 5 minutes charge will allow you to carry out 1 treatment. Battery indicator o Your treatment formulator is charged If you drop your appliance and it does not work normally, do not use it and contact an Authorized Service Centre.5554

Let’s help protect the environment Your appliance is designed to work for many years. But when you decide to replace it, don’t forget to think about how you can help to protect the environment by allowing it to be reused, recycled or recovered in some other way. This will prevent any harmful impact on the environment or on human health due to the uncontrolled disposal of waste that can contain dangerous substances. This label indicates that this product must not be disposed of with household waste. Take it to a collection point, to the distributor when buying a new equivalent product, or an approved service centre for processing. Before disposing of the appliance, remove the battery and dispose of it in accordance with the regulations and local arrangements. If you have any questions, contact the DUOLAB customer service. DUOLAB promotes the collection of used capsules.

1. Remove your capsules by gently pulling capsule 2 out of the dispenser.

There’s no need to open the dispenser to do this.

2. Keep your capsules in your recycling bin.

3. Once your bin is full, recycle your capsules. You can find more information

on the ocial Duolab website for your region.5756

6. W PRZYPADKU PROBLEMÓW