CK490 - Food Processor Wëasy - Free user manual and instructions

USER MANUAL CK490 Wëasy

Read this booklet thoroughly before using and save it for future reference

IMPORTANT SAFEGUARDS

Before using the electrical appliance, the following basic precautions should always be followed including the following:

1. Read all instructions, and save it for future reference.
2. Before using, check that the voltage of wall outlet corresponds to that shown on the rating plate.
3. Do not operate this appliance if it has a damaged cord or plug, if it is not working properly or if it has been damaged or dropped. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
4. Do not let cord hang over edge of table or counter.
5. To protect against risk of electrical shock, do not put the motor base into water or other liquid. To disconnect, turn any control to "off", then remove plug from wall outlet by grasping the plug, not the cord.
6. This appliance may be used by persons with reduced physical, sensory or mental capabilities or lack of experience or knowledge, provided that they are supervised or instructed in the safe use of the appliance and that they fully understand the potential hazards.
7. Close supervision is necessary when any appliance is used by or near children.

8. Keep hands and utensils away from moving blades or discs while processing food to reduce the risk of severe injury to persons or damage to the Food Processor. A scraper or spatula may be used, but must be used only when the Food Processor is not running.

9. Avoid contacting moving parts.

10. Never feed food by hand. Always use food pusher.
11. Before removing the lid from the jar from the power unit, switch off the unit, wait until the blades have come to a complete stop.
12. Do not use fingers to scrape food away from discharge disc while appliance is operating. Cut type injury may result.
13. Be certain lid is securely locked into place before operating appliance.
14. Always remove the blade assembly before pouring contents from jar.
15. Be sure to switch off the appliance after each use of your food processor. Make sure the motor stops completely before disassembling.
16. Do not put your fingers or other objects into the unit opening while it is in operation. If food becomes lodged in opening, use food pusher or another piece of fruit or vegetable to push it down. When this method is not possible, turn the motor off and disassemble to remove the remaining food.
17. Do not attempt to defeat the cover interlock mechanism.
18. The metal blades and disk is extremely sharp, handle with care. Always hold the blade assembly by the finger grip or stem, away from the cutting edge, both when handling and cleaning.
19. To reduce the risk of injury, never place processing blade or circle blade assembly on drive shaft without the processing jar locked properly in place.
20. Do not leave this appliance unattended during use.

21. If this appliance falls or accidentally becomes immersed in water, unplug it immediately. Do not reach into the water! Do not use this appliance after it has fallen into or becomes immersed in water.

22. To reduce the risk of injury to persons or property, never use this appliance in an unstable position.

23. Do not use this appliance for other than its intended use.
24. The use of attachments not recommended or sold by the manufacturer may cause fire, electric shock or injury.
25. Do not use outdoors.
26. Unplug from outlet when not in use, before putting on or taking off parts, and before cleaning.

Caution: never immerse in water, unplug before inserting or removing parts.

1. Caution: DO NOT OPEN LID UNTIL BLADES STOP.
2. Note: This Food Processor is the multipurpose appliance, plastic blade for kneading can create maximum rating. Other recommended attachments may draw significantly less current.
3. Be careful when handing the sharp cutting blades, emptying the bowl and during cleaning.
4. Be careful if hot liquid is poured into the food processor or blender as it can be ejected out of the appliance due to a sudden steaming.
5. Switch off the appliance and disconnect from supply before changing accessories or approaching parts that move in use.
6. This device is not intended for use by persons with reduced capacity on the physical, mental or sensory or lack of experience and knowledge (including children), unless they have had instructions to use the appliance by a person responsible for their safety use of the appliance and understand the hazards involved. Children should be supervised to ensure they do not play with the device.

7. Children should be supervised to ensure that they do not play with the appliance.

8. Type Y: If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.

9. The operating times and speed settings for accessories should be given (Details)
10. Always disconnect the blender from the supply if it is left unattended and before assembling, disassembling or cleaning;
11. Do not allow children to use the blender without supervision;
12. How to clean surfaces in contact with food. (Details);
13. Switch off the appliance and disconnect from supply before changing accessories or approaching parts that move in use.
14. Care shall be taken when handling the sharp cutting blades, emptying the bowl and during cleaning.
15. This appliance is intended to be used in household and similar applications such as:
16. staff kitchen areas in shops, offices and other working environments;
    -farm houses;
17. by clients in hotels, motels and other residential type environments;
18. bed and breakfast type environments.
19. The device must not be used if it has been dropped, it obvious signs of damage are visible or if it has leaks.

KNOW YOUR FOOD PROCESSOR

CONTROL PANEL

OFF: When you want to stop the appliance during operation or when the machine finishes processing or when the unit is not in use, always press the "OFF" button.

PULSE: Press and hold the button for short or delicate processing tasks. PULSE is used most frequently, as it gives greater control over food processing and fineness.

LO: low speed, it is suitable for kneading or mixing.

HI: high speed, it is suitable for chopping or slicing/chipping.

BEFORE FIRST USE

Before first use, carefully unpack the food processor and its attachments and remove any package material or label or stickers. Clean all the parts except the motor base following the instructions in CLEANING AND MAINTENANCE. Handle the "S" blade or circle blade assembly with extreme care as they are sharp.

USING YOUR FOOD PROCESSOR

CHOPPING

1. Firstly assemble the driving shaft into the motor base, make sure it is clipped into position.
2. Place the jar on the motor base and turn it clockwise until it locks into position. Make sure it is assembled in place correctly, otherwise the appliance will not operate.
3. Insert the "S" blade into the driving shaft in the jar securely.

Then place the prepared chopping food into the jar. The food must be cut into small size firstly (such as 2cm^ 2cm^ 6cm for beef). During chopping, you can add food through the feeding funnel with the pusher, never using food or finger to push the food into the feeding funnel. When chop fig, the proportion of fig to honey shall be 380g : 300g and the operation time shall not be more than 30S.

1. Place the lid onto the jar and turn it clockwise until the tab of the lid clicks into slot in the jar handle. Make sure it is locked in position correctly, otherwise the appliance will not operate.
2. Connect the appliance to power supply. Press the corresponding speed button according to your task. You can chop up to 400g of following foodstuff,

Hard substance: cheese, dried fruits, and certain vegetables (carrots, celery...),

Soft substance: certain vegetables (onions, spinach...)

Raw and cooked meat (boned and sliced)

CAUTION: The total operating time should not be more than 30 sec.
6. Press the "OFF" button and unplug the appliance after chopping. Grasp blade by its hub and remove. Unlock jar by turning it in anti-clockwise away from its base, and lift it off. Empty the processed food.

CAUTION: The "S" blade is extremely sharp, handle with care.

CLEANING

1. Disconnect the power supply before cleaning.
2. Empty the jar, dismantle all detachable parts and rinse them in warm soapy water. Extreme caution must be taken when handling blade as it is very sharp. All the accessories except motor base are dishwasher safe components, but the temperature setting shall not exceed 70^ . Then dry thoroughly.
3. Wipe the outside of base with damp cloth. Never immerse it in water as electric shock is possible to occur.

Then dry thoroughly. Ensure the interlock area is free of food particles

FOR A QUICK WASH UP

Between processing tasks, pour in some water into the jar, press and hold the PULSE button for several seconds for quick cleaning.

KNEADING/MIXING

1. Firstly assemble the driving shaft into the motor base, make sure it is clipped into position.
2. Place the jar on the motor base and turn it clockwise until it locks into position. Make sure it is assembled in place correctly, otherwise the appliance will not operate.
3. Insert the plastic blade into the driving shaft in the jar securely.
4. Measure the flour with measuring cup and put them into the jar. The maximum quantity of flour is 500g.
5. Place the lid onto the jar and turn it clockwise until the tab of the lid clicks into slot in the jar handle. Make sure it is locked in position correctly, otherwise the appliance will not operate.
6. Add one tablespoon oil into the appliance from the feeding funnel. Connect the appliance to power supply. Press down the HI button.
7. Then add water (the maximum water quantity is 300g ) with measuring cup from the feeding funnel slowly within 20s.
8. The proportion of the flour and water is 10:6. Make sure the quantity of the water shall not be more than the maximum specified water quantity.

Note: Add some more water if the processing speed slows down during operating so as to make the motor run smoothly, otherwise the motor may be damaged. During kneading/mixing, to avoid shaking, press the lid with one hand, and the other hand is holding the handle.

1. Stop the process by pressing the OFF button as soon as the pastry starts to form a ball.

CAUTION: The total operation time is not more than 90 seconds.

1. Unplug the appliance, detach the cover, firstly remove the plastic blade, then remove the dough.

CLEANING

1. Disconnect the power supply before cleaning.
2. Empty the jar and remove the lid, the plastic blade, pusher, then immerse them in water and clean them with a damp cloth or soft brush.
3. Wipe the outside of base with a damp cloth. Never immerse the motor base in water as electric shock is possible to occur. Then dry thoroughly. Ensure the interlock area is free of food particles.

SLICING/CHIPPING

1. Firstly assemble the driving shaft into the motor base, make sure it is clipped into position.
2. Place the jar on the motor base and turn it clockwise until it locks into position. Make sure it is assembled in place correctly, otherwise the appliance will not operate.
3. Insert the circle blade assembly into the driving shaft in the jar securely.

Note: if you want to slice, make the surface with slicing blade upward during assemble the circle blade assembly; if you want to chip, make the surface with chipping hole upward.

1. Place the lid onto the jar and turn it clockwise until the tab of the lid clicks into slot in the jar handle. Make sure it is locked in position correctly, otherwise the appliance will not operate.
2. Press the corresponding speed button according to your task.
   Note: the slicing/chipping blade can slice/chip thickly-potatoes, onions, thinly-cucumbers, boot root, apples, and carrots...
3. Use the pusher to feed food into the feeding funnel. The food shall be cut into proper size to suitable for the feeding funnel (the length of food shall be less than 120mm ). You can slice/chip up to 500g of food.
4. The total operating time should not more than 60s.
5. Press the "OFF" button and unplug unit after processing. Remove the circle blade ass' by its hub Unlock jar by turning it in anti-clockwise away from its base, and lift it off. Empty the processed food.

CAUTION: The circle blade assembly is extremely sharp, handle with care.

CLEANING

1. Disconnect the power supply before cleaning.
2. Empty the jar, dismantle all detachable parts and rinse them in warm soapy water. Extreme caution must be taken when handling disks as they are very sharp. Then dry thoroughly.
3. Wipe the outside of base with cloth. Never immerse it in water as electric shock is possible to occur. Then dry thoroughly. Ensure the interlock area is free of food particles.

Note: Some food may discolor the circle blade disk. This is normal and will not harm the plastic or affect the flavor of food. Rub with cloth dipped with vegetable oil to remove discoloration.

WARRANTY

The warranty period for our products is 2 years, unless otherwise stated, starting from the date of initial purchase or the date of delivery.

If you have any problems or questions, you can easily access our help pages, troubleshooting tips, FAQ, and user manuals on our service site: https://sav.hkoenig.com.

By typing the reference name of your device in the search bar, you can access all available online support, designed to best meet your needs.

If you still cannot find an answer to your question or problem, then click on "Did the answer solve your problem?" This will direct you to the Customer Support Request Form, which you can fill out to validate your request and get help.

WARRANTY CONDITIONS

The warranty covers all failures occurring under normal use, in accordance with the usage and specifications in the user's manual.

This warranty does not apply to packaging or transportation problems during shipment of the product by the owner. It also does not include normal wear and tear of the product, nor maintenance or replacement of consumable parts.

EXCLUSION OF WARRANTY

• Accessories and wearing parts () .
• Normal maintenance of the device.
• All breakdowns resulting from improper use (shocks, failure to comply with power supply recommendations, poor conditions of use, etc.), insufficient maintenance or misuse of the device, as well as the use of unsuitable accessories.
• Damage of external origin: fire, water damage, electrical surge, etc.
• Any equipment that has been disassembled, even partially, by persons other than those authorized to do so (notably the user).
• The products whose serial number would be missing, deteriorated or illegible that would not allow its identification.
• The products subjected to leasing, demonstration, or exhibition.

(*) Some parts of your device, called wear parts or consumables, deteriorate with time and frequency of use of your device. This wear and tear are normal but can be accentuated by poor conditions of use or maintenance of your device. These parts are therefore not covered by the warranty.

The accessories supplied with the device are also excluded from the warranty. They cannot be exchanged or refunded. However, some accessories can be purchased directly through our website: https://sav.hkoenig.com/.

ENVIRONMENT

CAUTION:

Do not dispose of this product as it has with other household products. There is a separation of this waste product into communities, you will need to inform your local authorities about the places where you can return this product. In fact, electrical and electronic products contain hazardous substances that have harmful effects on the

environment or human health and should be recycled. The symbol here indicates that electrical and electronic equipment should be chosen carefully, a wheeled waste container is marked with a cross.

FRANÇAIS

CONDITIONS DE GARANTIE

KENNEN SIE IHRE KÜCHENMASCHINE

BEDIENFELD

EEN SNELLE SCHOOLMAAK