GP 1100.1 - Water pump Güde - Free user manual and instructions

Product type	Garden water pump
Brand	Güde
Model	GP 1100.1
Rated voltage	220 - 240 V
Frequency	50 Hz
Motor power (P1)	1100 W
Insulation class	F
Protection degree	IP X4
Max. flow rate	4.600 l/h
Max. delivery head	46 m
Max. suction head	8 m
Max. water temperature	35 °C
Connection	IG 1"
Dry running protection	No
Net weight	10.6 kg
Gross weight	12.0 kg
Dimensions (L x W x H)	465 x 205 x 300 cm
Ambient humidity and temperature	0 °C to 40 °C
Number of pages in the manual	80 pages
Available languages	FR, CS, DE, EN, ES, HU, IT, NL, PL, SK
Maintenance	Regular cleaning of the foot valve and pre-filter; drain before winter; store frost-free
Safety	Use a 30 mA residual current device; do not pump drinking water; do not run dry

Frequently Asked Questions - GP 1100.1 Güde

What to do if the pump does not start?

First check the supply voltage. If the voltage is correct, the pump impeller may be blocked. Turn the motor shaft with a screwdriver through the fan cover after loosening the glued joint of the thrust washer.

Why does the pump not suck?

Possible causes are: missing, blocked or not immersed foot valve; pump body without water; suction head too high; air bubbles in the suction line; non-tight connections. Check and correct each point.

How to prime the pump before use?

Fill the pump body with water through the filling opening. Ensure the suction line is tight and the foot valve is immersed. The pump must be primed to operate correctly.

What is the maximum suction head of the pump?

The maximum suction head is 8 meters. Beyond that, the pump may not suck properly.

Can I use this pump for drinking water?

No, it is strictly forbidden to use this pump for pumping drinking water. It is designed only for clean water not intended for human consumption.

How to maintain the pump before winter?

Completely drain the pump and hoses to prevent frost damage. Store it frost-free. You can rinse the pump with vegetable oil to reduce sticking of the mechanical seals.

What to do if the water flow is insufficient?

Check the suction head (max. 8 m), clean the suction strainer of the foot valve, and check the water level. If the level drops quickly, lower the foot valve.

The pump stops after a while and overheats, what to do?

The thermal protection has cut off the power due to overheating. Let the pump cool down. Check that the power supply is correct and that no impurities block the suction opening.

What accessories are recommended for this pump?

Use a suction hose with non-return valve, a foot valve and a pre-filter. The manual mentions Teflon sealing tape for the connections.

Where can I find spare parts or the manual?

Go to www.guede.com in the Service section. Have the serial number, order number and year of manufacture (on the rating plate) ready.

USER MANUAL GP 1100.1 Güde

Translation of the original instructions

Blue industrial pump with black internal components and control panel (no visible text or symbols)

Blue industrial pump with black and white components (no visible text or symbols)

Illustration of a blue industrial pump connected to a metallic cylindrical tank (no text or symbols visible)

GP 1100.1

93905

HWA 1100.1 VF

93907

HWW 1100.1 VF

93906

HWW 1400.2 VF

93908

HWW 1400.3 VF INOX

93909

ENGLISH Please read the instructions carefully before starting the machine.

Blue industrial pump with control panel and pressure gauge (no visible text or symbols)

GP 1100.1

93905

Blue industrial pump with black internal components and control panel (no visible text or symbols)

HWA 1100.1 VF

93907

Illustration of a blue industrial pump and a metallic cylindrical tank (no text or symbols visible)

HWW1100.1 VF

93906

HWW1400.2VF

93908

HWW 1400.3 VF INOX

93909

Deutsch Technische Daten / Gerätebeschreibung / Sicherheitshinweise / Bestimmungs-gemäße Verwendung / Verhalten im Notfall / Symbole / Wartung / Entsorgung / Gewährleistung / Service ____ 19
English Technical Data / Device description / Safety Warnings / Specified Conditions of Use / Emergency procedure / Symbols / Maintenance / Disposal / Guarantee / Service 24
Français Caractéristiques techniques / Description du dispositif / Instructions De Sécurité Particulieres / Utilisation conforme aux prescriptions / Conduite en cas d'urgence / Symboles / Entretien / Elimination / Garantie / Service ____ 29
Italiano Dati tecnici / Descripción del dispositivo / Norme Di Sicurezza / Utilizzo conforme / Comportamento in caso d'emergenza / Simboli / Manutenzione / Smaltimento / Garanzia / Servizio ____ 34
Español Datos técnicos / Descripción del dispositivo / Indicaciones de seguridad / Aplicación de acuerdo a la finalidad / Comportamento in caso d'emergenza / Símbolos / Mantenimiento / Eliminación / Garantía / Servicio ____ 39
Nederlands Technische gegevens / Beschrijving van het apparaat /Veiligheidsadviezen / Voorgeschreven gebruik van het systeem / Handelswijze in noodgeval / Symbolen / Onderhoud / Afvoer / Garantie / Service ____ 44
Čeština Technická data / Popis zařízení / Speciální Bezpečnostní Upozornění / Oblast Využití / Chování v případě nouze / Symboly / Údržba / Likvidace / Záruka / Servis____49
Slovenský Technické údaje / Opis zariadenia / Špeciálne Bezpečnostné Pokyny / Použitie podľa predpisov / Správanie v prípade núdze / Symboly / Údrzba / Likvidácia / Záruka / Servi ____ 54
Polski Dane techniczne / Opis urządzenia / Instrukcje Dotyczące Bezpieczeństwa / Warunki użytkowania / Postępowanie w nagłym przypadku / Symbole / Utrzymanie I Konserwacja / Utylizacja / Gwarancja / Serwis ____ 59
Magyar Műszaki Adatok / Eszközleírás /Rendeltetés szerinti használat / Biztonsági utasítások / Karbantartás / Jótállás ____ 64

Inbetriebnahme

EN starting-up the device FR Mise en service IT Messa in funzione

ES Puesta en marcha NL Toestel in gebruik nemen cz Uvedení do provozu

HWA 1100.1 VFGP 1100W 1400.2 VF

HWW 1400.3 VF INOXHWW 1100.1 VF

1

Teflon-Dichtband

teflon sealing tape

Close-up of a hand holding a cylindrical mechanical component with an arrow indicating rotation (no text or symbols visible)

A

+

B

3

Suction hose with check valve

Green flexible hose with attached connectors (no text or symbols visible)

KA 4 P / 94440

KA 7 P / 94441

2

A

Diagram showing a black pipe with a valve and red X-shaped mark indicating a water level, next to a pressure vessel (no text or symbols present)

4

GP 1100.1

HWA 1100.1 VF

HWW 1100.1 VF

HWA 1100.1 VFGP HM0V11400.2 VF

HWW 1400.3 VF INOXHWW 1100.1 VF

HWA 1100.1 VFGP HM0V11400.2 VF

HWW 1400.3 VF INOXHWW 1100.1 VF

GP 1100.1

Diagram of a mechanical system with a pump connected to a tank, showing fluid flow and wiring (no text or labels)

HWA 1100.1 VF

Diagram of a water pump system with a blue motor and black piping, connected to a water tank (no text or labels)

Close-up of a blue industrial machine component with a red button labeled 'I' and a white arrow pointing to it (no readable text or symbols beyond labels)

HWW 1400.2 VF

HWW 1100.1 VF

Diagram of a pressure vessel connected to a pump via tubing, with a water tank at the bottom (no text or labels)

Close-up of a blue industrial machine control panel with a white arrow pointing to a red button (no visible text or symbols)

Diagram of a faucet with water droplets falling into the drain, showing a circular object above it (no text or symbols)

Simple black-and-white diagram of a faucet with a circular component above it, no text or symbols present.

HWW 1400.3 VF INOX

Diagram of a water pump system with a blue and silver cylinder connected to a water tank, showing pipe flow and a water outlet (no text or labels)

Close-up of a blue industrial machine control panel with a red square button and a white arrow pointing to it (no visible text or symbols)

Illustration of a faucet with water droplets falling into the mouth, above a wall (no text or symbols)

3

Automatic Mode

graph LR
    A["Power on"] --> B{Check}
    B --> C["Set"]
    B --> D["Mode"]
    E["Automatic Mode 4000 L/H"] --> F{Check}
    F --> G["Set"]
    F --> H["Mode"]

HWW 1400.3 VF INOX

graph LR
    A["Automatic Mode Check"] --> B["Check Water"]
    B --> C{Check}
    C --> D["DE Trockenlaufschutz aktiv"]
    C --> E["EN Dry run protection active"]
    C --> F["FR Protection contre le fonctionnement à sec active"]
    C --> G["IT Protezione contro l'avviamento a secco attivo"]
    C --> H["ES Protección contra marcha en seco activa"]
    C --> I["NL Droogloopbeveiliging actief"]
    J["CZ Ochrana proti suchémuchodu aktivní"] --> K["SK Ochrana pred behom nasucho aktívna"]
    J --> L["PL Aktywne zabezpieczenie przed pracą na sucho"]
    J --> M["HU A szárazon futás ellení védelem aktiv"]

HWW 1400.3 VF INOX

Time Now

graph TD
    A["Automatic Mode Check"] --> B["Time Now 00:00"]
    B --> C["Next"]
    C --> D["Time Now 12:00"]
    D --> E["Next"]
    E --> F["Time Now 12:15"]
    F --> G["Save Set Exit"]

HWW 1400.3 VF INOX

Ever on

graph TD
    A["Time Mode\n12:19:32"] --> B["Check"]
    A --> C["Set"]
    A --> D["Mode"]
    E["Time Mode\n12:19:32"] --> F["Check"]
    E --> G["Set"]
    E --> H["Mode"]
    I["Ever on"] --> J["Check"]
    I --> K["Set"]
    I --> L["Mode"]
    M["Ever on"] --> N["Check"]
    M --> O["Set"]
    M --> P["Mode"]

Ever on - Stop

Close-up of a blue industrial machine control panel with a red indicator light and an arrow pointing to the button (no text or symbols visible)

HWA 1100.1 VFGP HM0V11400.2 VF

HWW 1400.3 VF INOXHWW 1100.1 VF

Diagram of a water pump system with pipe connections and a water tap (no text or labels)

Close-up of a blue industrial machine with a red control panel and circular button (no visible text or symbols)

Diagram of a pressure pump system with tubing and a water tank, no text or symbols present

Mechanical assembly diagram showing a cylindrical component with a blue housing and a rotating knob, alongside a close-up view of the knob's rotation (no text or symbols present)

Mechanical setup showing a metallic cylindrical tank connected to a pressure gauge and a vertical support (no text or symbols visible)

Mechanical assembly diagram showing a cylindrical component with mounting holes and a directional arrow indicating rotation (no text or symbols)

HWA 1100.1 VFGP HM0V11400.2 VF

HWW 1400.3 VF INOXHWW 1100.1 VF

HWA 1100.1 VFGP HM0V11400.2 VF

HWW 1400.3 VF INOXHWW 1100.1 VF

Illustration of a mechanical device being processed with a tool, showing fluid flow and component placement (no text or symbols)

Technische Daten

Garden pump GP 1100.1
Art. No 93905
Rated voltage 220 - 240 V
Frequency 50 Hz
Motor power P1 1100 W
Insulation class F
Degree of protection IP X4
Qmax Max. delivered quantity 4.600 l/h
H min min. Head height 2 m
H max Max. head of delivery 46 m
Max. suction head	8 m
Max. Water temperature 35 °C
Service connection IG 1"
Dry run protection	No
Net/gross weight	10,6 / 12,0 kg
Dimensions L x W x H	465 x 205 x 300 cm

Domestic water supply system	HWA1100.1 VF
Art. No	93907
Rated voltage	220 - 240 V
Frequency	50 Hz
Motor power P1	1100 W
Insulation class	F
Degree of protection	IP X4
Qmax Max. delivered quantity	4.600 l/h
Hmin min. Head height	2 m
Hmax Max. head of delivery	46 m
Max. suction head	8 m
Max. Water temperature	35 °C
Service connection	IG 1 “
Dry run protection	Yes
Net/gross weight	16,65 kg / 18,90 kg
Dimensions L x W x H 465 x 205 x 300 cm

Domestic water supply unit	HWW 1100.1 VF	HWW 1400.2 VF	HWW 1400.3 VF INOX
Art. No	93906 93908 93909
Rated voltage	220 - 240 V	220 - 240 V	220 - 240 V
Frequency	50 - 60 Hz	50 Hz	50 Hz
Motor power P1	1100 W 1400 W 1400 W
Insulation class	F	F	F
Degree of protection	IP X4	IP X4	IP X4
Qmax Max. delivered quantity	4.600 l/h	4.800 l/h	4.800 l/h
H min min. Head height	2 m	2 m	2 m
H max Max. head of delivery	46 m	48 m	48 m
Max. suction head	8 m	8 m	8 m
Max. Water temperature	35 °C	35 °C	35 °C
Service connection	IG 1 "	IG 1 "	IG 1 "
Tank capacity	24 l	24 l	24 l
Dry run protection No Yes	Yes
Net/gross weight	16,64 kg / 18,90 kg	16,85 kg / 19,10 kg	16,85 kg / 19,10 kg
Dimensions L x W x H	500 x 265 x 600 cm	500 x 265 x 600 cm	500 x 265 x 600 cm

Read and understand the operating instructions before using the appliance. Abide by all the safety measures stated in the service

manual. Act responsibly toward third parties. In case of any doubts about connection and operation refer please to our customer center

Specified Conditions of Use

The pump is designed for pumping clean water only to supply the home with water and to use it at home, in garden, courtyard and for fields. Respecting technical data and safety precautions.

Do not use this product in any other way as stated for normal use. Not observing general regulations in force and instructions from this manual does not make the manufacturer liable for damages.

The pump is not suitable for long-term operation (e.g. as a circulating pump in ponds or for brooks). If this type of operation is carried out, the service life will be reduced accordingly.
Do not leave the pump unattended while in operation in order to prevent subsequent damages caused by eventual malfunctions. Make sure to disconnect the device from the grid if you do not plan on using it.
⚠ Do not use the pump for drinking water!
The pump must not be connected to the existing water-supply network as a pressure-boosting device.
⚠️ Never use the pump as a pool circulation pump.

Safety Warnings

WARNING! Electric shock! There is a risk of an injury caused by electric shock!

This appliance is not intended for use by persons (including children) with limited physical, sensory or mental capabilities or insufficient experience and/or knowledge unless they are supervised by a person who is responsible for their safety or have been instructed by them in the safe use of the appliance.

Children should be supervised in order to ensure that they do not play with the tool. Always keep children and unauthorised persons out of reach of the appliance.

Operation is only allowed with a safety switch against stray current (RCD max. stray current of 30mA).

Before putting into operation, a qualified electrician must check whether electric safety measures required are in place. Any national regulations in this regard must be complied with.

Electric connection to a socket.

Do not expose tools to rain. Do not use tools in damp or wet locations.

It is necessary to make sure the connecting socket was not near water and humidity and the plug was protected against humidity.

Avoid installing the appliance in wet shafts (risk of short circuit, corrosion effects)!

Check the voltage. Technical data given on the type label must correspond with electric network voltage.

Only use splash proof extension cables approved for outdoor purposes.

Do not grab the feeder cable, plunge the pump, lift or carry it while it is connected to the grid!

Check the cable and/or socket for damages before the appliance putting into operation.

To avoid danger, a damaged mains supply pipe must be replaced by the manufacturer. Do not under any circumstances attempt any repair yourself.

Protect the feeder cable from excessive temperatures, oil and sharp edges.

⚠️ If the pump is in operation, neither people nor animals can be present or plunged in the pumped liquid (e.g. pools, cellars, etc.).
⚠️ The pump must not in any case run without fillings

Do not leave the pump unattended while in operation in order to prevent subsequent damages caused by eventual malfunctions. Make sure to disconnect the device from the grid if you do not plan on using it.

The temperature of the drained liquid must not exceed +35 °C.

When using the pump for domestic water supply, always observe the local regulations of water management authorities and the waste water drainage.

If the pump is used in ponds, wells, etc. and appropriate pumping stations, standards valid for pumps in the given country must unconditionally be observed.

Do not use pump at outside temperatures over 40 °C or under 0 °C

In cold weather, the pumping body motor should not be wrapped in a blanket or another piece of textile with intent to prevent the water freezing.

The user is responsible to third parties if pump (dumping stations, etc.) is used.

Water escapes between the motor and pump, mechanical seal leaks (approx. 35 drops of water per day is considered insignificant, this leakage is functional with a mechanical seal).

Requirements for operating staff

The operating staff must carefully read the Operating Instructions before using the appliance.

Qualification: Apart from the detailed instructions by a professional, no special qualification is necessary for appliance using.

Minimum age: Persons over 16 years of age can only work on the appliance. An exception includes youngsters trained in order to reach knowledge under supervision of the trainer during occupational education.

Training: Using the appliance only requires corresponding training by a professional or the Operating Instructions. No special training is necessary.

Emergency procedure

Conduct a first-aid procedure adequate to the injury and summon qualified medical attendance as quickly as possible. Protect the injured person from further harm and calm them down. For the sake of eventual accident, in accordance with DIN 13164, a workplace has to be fitted with a first-aid kit. It is essential to replace any used material in the first-aid kit immediately after it has been used. If you seek help, state the following pieces of information

1. Accident site
2. Accident type
3. Number of injured persons
4. Injury type(s)

Maintenance

⚠️ Before any adjustment, cleaning and maintenance work, switch off the device and disconnect it from the power supply.

Prior to every use, visually check the machine to rule out any defects, in particular on the power cable and the plug.

The appliance must not be used if damaged or safety equipment is defective. Replace any worn-out and damaged parts.

Repairs and works specified in these Instructions may only be performed by qualified authorised staff. Use only original accessories and original spare parts.

Caution! Depending on the design, water that is left standing for a longer period of time may cause corrosion in the pump housing! (Brown colouration)

For winter storage, ensure that there is no water in the device. Otherwise, frost exposure may cause irreparable damage to the device. The pump must be stored in a completely empty and frost-proof state. You can reduce the chance of the mechanical seals sticking by flushing out the pump with suitable oil (e.g. vegetable oil).

Only a regularly maintained and treated appliance can serve as a satisfactory aid. Insufficient maintenance and care can lead to unforeseen accidents and injuries.

Guarantee

Warranty period of 12 months applies to commercial use and 24 months applies to private use and commences on the day of purchase of the device.

The guarantee solely covers inadequacies caused by material defect or manufacturing defect. Original payment voucher with the sales date needs to be submitted for any claim in the guarantee period.

The guarantee does not cover any unauthorised use such as appliance overloading, use of violence, damage as a result of any unauthorised interference or caused by foreign items. Failing to follow the operating and assembly instructions and common wear are also not included in the guarantee.

GÜDE cannot be held responsible for damages incurred in consequence of unqualified installation or unskilled handling of the pump.

The device has to be checked on a regular basis to ensure perfect functioning.

Let us refer to the fact we do not assume any responsibility – according to standards in force – for damage eventually caused by our appliances in the below-mentioned cases: Unprofessional repairs executed by unauthorised service centres; Use in conflict with the designed purpose, or failure to observe the use as designed; Pump overload with a continuous run; Damage as a result of icing or any other fault caused by climatic influences; Identical regulations apply for accessory parts.

To prevent damage (such as flooded rooms, etc.) as a result of faulty pump operation (failure or fault) the owner (user) is obliged to take reasonable safety measures (alarm assembly, spare pump, etc.).

Service

Do you have any technical questions? Any claim? Do you need any spare parts or operating instructions? We will quickly help you and without needles bureaucracy at our web pages at www.guede.com in the Servicing part. Please help us be able to help you. In order to identify your device in case of claim we need the serial No., product No. and year of production. All this data can be found on the type label.

Serial No.:

Art. No:

Year of production:

SYMBOLS

Read the operating instructions to reduce the risk of injury.

Machine to be always unplugged before any adjustment and servicing work on it.

Insert the mains plug

Staying in the transportation medium prohibited

Warning against dangerous voltage

Warning about automatic start-up

Any damaged or disposed electric or electronic devices must be delivered to appropriate collection centres.

CE marking

TÜV / GS conformity mark

Inspection and maintenance plan

Time interval Description Any other details
As needed Clean the check valve and the prefilter. Check the check valve function.
As required	Check pressure pipe and intake pipe for leakage and seal if necessary	Check for any leaks
As required	Check and correct tank pressure See page 16;Tank pressure 1,5 – 1,8 Bar

Failure removal

Failures Causes Removal
Engine does not start No power supply. Blocked pump wheel		Turn the engine shaft with screwdriver through the fan cover (to release friction circles sealing that may be stuck together).
Pump does not suck Missing, loose or blocked check valve Check valve is not in water. No water in the pump shell. Too high suction head. Air bubbles in the suction pipeline. Connections not sealed, pump sucks air, pump is not deaerated. Prefilter clogged		Fix or clean the check valve. Immerse the check valve into water. Fill the pump shell with water. Check the suction head. Check the tighten of suction pipeline. Carefully repeat connection according to the chapter „Connection“! Clean the prefilter.→17
Thermal detector switching the pump off →4	Pump is overheated and switched off by the thermal overloading protection. No electric power supply. Impurity particles (e.g. pebbles) have settled down in the suction hole.	Let the device getting cool! Check power supply. Disassemble and clean the suction hose, prevent from suction of foreign substances.
Insufficient amount of water pumped	Too high suction head. Strainer of the check valve dirty Clean the strainer., Position the check valve lower. Water level quickly drops down Check water level	Check the suction head.
Reduced switching intervals	Air pressure in the receiver too low Seals on the pre-filter/non-return valve dirty	Control air pressure.→16 Clean the seals and grease them with Vaseline
Water is coming out of the tank valve	Membrane defective	Replace/repair (specialist workshop)

Translation of the EC-Declaration of Conformity

We, hereby declare the conception and construction of the below mentioned appliances correspond - at the type of construction being launched - to appropriate basic safety and hygienic requirements of EC Directives.

In case of any change to the appliance not discussed with us the Declaration expires.

Notified Body Name: No: Adress:

Type Ex. Cert.-No.:

2016/1628/EU_2018/989/EU

Emission No.:

2000/14/EC_2005/88/EC

Notified Body Name: No: Adress:

Type Ex. Cert.-No.:

2016/1628/EU_2018/989/EU

Emission No.:

2000/14/EC_2005/88/EC

Notified Body Name: No: Adress:

Type Ex. Cert.-No.:

2016/1628/EU_2018/989/EU

Emission No.:

2000/14/EC_2005/88/EC

Notified Body Name: No: Adress:

Type Ex. Cert.-No.:

2016/1628/EU_2018/989/EU

Emission No.:

2000/14/EC_2005/88/EC