RS002G - Saw MAKITA - Free user manual and instructions

USER MANUAL RS002G MAKITA

Cordless Rear Handle Saw INSTRUCTION MANUAL 9

• Specicationsmaydi󰀨erfromcountrytocountry.

• Theweightmaydi󰀨erdependingontheattachment(s),includingthebatterycartridge.Thelightestandheavi- est combinations, according to EPTA-Procedure 01/2014, are shown in the table. Applicable battery cartridge and charger Batterycartridge BL4020 / BL4025 / BL4040 / BL4050F* / BL4080F* *:Recommendedbattery Charger DC40RA / DC40RB / DC40RC

• Someofthebatterycartridgesandchargerslistedabovemaynotbeavailabledependingonyourregionof residence.

WARNING: Only use the battery cartridges and chargers listed above.Useofanyotherbatterycartridges

WARNING: Wear ear protection.

WARNING: The noise emission during actual

use of the power tool can di󰀨er from the declared value(s) depending on the ways in which the tool is used especially what kind of workpiece is processed.

WARNING: Be sure to identify safety mea-

sures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched o󰀨 and when it is running idle in addition to the trigger time). Vibration Thevibrationtotalvalue(tri-axialvectorsum)deter- mined according to EN62841-2-5: Work mode: cutting wood Vibrationemission(a h,W ):2.5m/s

NOTE:Thedeclaredvibrationtotalvalue(s)hasbeen measured in accordance with a standard test method andmaybeusedforcomparingonetoolwithanother. NOTE:Thedeclaredvibrationtotalvalue(s)mayalso beusedinapreliminaryassessmentofexposure.10 ENGLISH

WARNING: The vibration emission during

actual use of the power tool can di󰀨er from the declared value(s) depending on the ways in which the tool is used especially what kind of workpiece is processed.

WARNING: Be sure to identify safety mea-

sures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched o󰀨 and when it is running idle in addition to the trigger time). Declarations of Conformity For European countries only TheDeclarationsofconformityareincludedinAnnexA to this instruction manual. SAFETY WARNINGS General power tool safety warnings WARNING Read all safety warnings, instruc- tions, illustrations and specications provided with this power tool. Failure to follow all instructions listed belowmayresultinelectricshock,reand/orserious injury. Save all warnings and instruc- tions for future reference. Theterm"powertool"inthewarningsreferstoyour mains-operated(corded)powertoolorbattery-operated (cordless)powertool. Cordless circular saw safety warnings Cutting procedures

DANGER: Keep hands away from cutting

area and the blade. Keep your second hand on auxiliary handle, or motor housing. If both handsareholdingthesaw,theycannotbecutby the blade.

2. Do not reach underneath the workpiece. The

guardcannotprotectyoufromthebladebelowthe workpiece.

3. Adjust the cutting depth to the thickness of

the workpiece. Less than a full tooth of the blade teeth should be visible below the workpiece.

4. Never hold the workpiece in your hands or

across your leg while cutting. Secure the workpiece to a stable platform. It is important to supporttheworkproperlytominimisebodyexpo- sure, blade binding, or loss of control. ►Fig.1

5. Hold the power tool by insulated gripping

surfaces, when performing an operation where the cutting tool may contact hidden wiring. Contact with a “live” wire will also make exposed metal parts of the power tool “live” and could give the operator an electric shock.

6. When ripping, always use a rip fence or

straight edge guide.Thisimprovestheaccuracy of cut and reduces the chance of blade binding.

7. Always use blades with correct size and shape

(diamond versus round) of arbour holes. Blades that do not match the mounting hardware ofthesawwillruno󰀨-centre,causinglossof control.

8. Never use damaged or incorrect blade wash-

ers or bolt. The blade washers and bolt were speciallydesignedforyoursaw,foroptimum performanceandsafetyofoperation. Kickback causes and related warnings — kickback is a sudden reaction to a pinched, jammedormisalignedsawblade,causingan uncontrolled saw to lift up and out of the workpiece toward the operator; — whenthebladeispinchedorjammedtightlybythe kerf closing down, the blade stalls and the motor reactiondrivestheunitrapidlybacktowardthe operator; — if the blade becomes twisted or misaligned in the cut, the teeth at the back edge of the blade can dig into the top surface of the wood causing the blade toclimboutofthekerfandjumpbacktowardthe operator. Kickbackistheresultofsawmisuseand/orincorrect operating procedures or conditions and can be avoided bytakingproperprecautionsasgivenbelow.

1. Maintain a rm grip with both hands on the

saw and position your arms to resist kickback forces. Position your body to either side of the blade, but not in line with the blade.Kickback couldcausethesawtojumpbackwards,but kickbackforcescanbecontrolledbytheoperator, if proper precautions are taken.

2. When blade is binding, or when interrupting a

cut for any reason, release the trigger and hold the saw motionless in the material until the blade comes to a complete stop. Never attempt to remove the saw from the work or pull the saw backward while the blade is in motion or kickback may occur. Investigate and take corrective actions to eliminate the cause of blade binding.

3. When restarting a saw in the workpiece, centre

the saw blade in the kerf so that the saw teeth are not engaged into the material. If a saw blade binds,itmaywalkuporkickbackfromthework- piece as the saw is restarted.

4. Support large panels to minimise the risk of

blade pinching and kickback. Large panels tend to sag under their own weight. Supports must be placed under the panel on both sides, near the line of cut and near the edge of the panel. ►Fig.2 ►Fig.3

5. Do not use dull or damaged blades.

Unsharpenedorimproperlysetbladesproduce narrow kerf causing excessive friction, blade binding and kickback.

6. Blade depth and bevel adjusting locking levers11 ENGLISH

must be tight and secure before making the cut.Ifbladeadjustmentshiftswhilecutting,itmay cause binding and kickback.

7. Use extra caution when sawing into existing

walls or other blind areas. The protruding blade maycutobjectsthatcancausekickback.

8. ALWAYS hold the tool rmly with both hands.

NEVER place your hand, leg or any part of your body under the tool base or behind the saw, especially when making cross-cuts. If kickback occurs,thesawcouldeasilyjumpbackwardsover yourhand,leadingtoseriouspersonalinjury. ►Fig.4

9. Never force the saw. Push the saw forward at a

speed so that the blade cuts without slowing. Forcing the saw can cause uneven cuts, loss of accuracy,andpossiblekickback. Lower guard function

1. Check the lower guard for proper closing

before each use. Do not operate the saw if the lower guard does not move freely and close instantly. Never clamp or tie the lower guard into the open position.Ifthesawisaccidentally dropped,thelowerguardmaybebent.Raisethe lower guard with the retracting handle and make sureitmovesfreelyanddoesnottouchtheblade oranyotherpart,inallanglesanddepthsofcut.

2. Check the operation of the lower guard spring.

If the guard and the spring are not operating properly, they must be serviced before use. Lowerguardmayoperatesluggishlydueto damagedparts,gummydeposits,orabuild-upof debris.

3. The lower guard may be retracted manually

only for special cuts such as “plunge cuts” and “compound cuts”. Raise the lower guard by the retracting handle and as soon as the blade enters the material, the lower guard must be released. For all other sawing, the lower guardshouldoperateautomatically.

4. Always observe that the lower guard is cover-

ing the blade before placing the saw down on bench or oor. An unprotected, coasting blade will cause the saw to walk backwards, cutting whatever is in its path. Be aware of the time it takes for the blade to stop after switch is released.

5. To check lower guard, open lower guard by

hand, then release and watch guard closure. Also check to see that retracting handle does not touch tool housing. Leaving blade exposed is VERY DANGEROUS and can lead to serious personalinjury. Additional safety warnings

1. Use extra caution when cutting damp wood,

pressure treated lumber, or wood containing knots. Maintain smooth advancement of tool with- out decrease in blade speed to avoid overheating the blade tips.

2. Do not attempt to remove cut material when

blade is moving. Wait until blade stops before grasping cut material.Bladescoastafterturno󰀨.

3. Avoid cutting nails. Inspect for and remove all

nails from lumber before cutting.

4. Place the wider portion of the saw base on

that part of the workpiece which is solidly supported, not on the section that will fall o󰀨 when the cut is made. If the workpiece is short or small, clamp it down. DO NOT TRY TO HOLD SHORT PIECES BY HAND! ►Fig.5

5. Before setting the tool down after completing a

cut, be sure that the guard has closed and the blade has come to a complete stop.

6. Never attempt to saw with the circular saw

held upside down in a vise. This is extremely dangerous and can lead to serious accidents. ►Fig.6

7. Some material contains chemicals which may

be toxic. Take caution to prevent dust inhala- tion and skin contact. Follow material supplier safety data.

8. Do not stop the blades by lateral pressure on

9. Do not use any abrasive wheels.

10. Only use the saw blade with the diameter that

is marked on the tool or specied in the man- ual.Useofanincorrectlysizedblademaya󰀨ect the proper guarding of the blade or guard opera- tionwhichcouldresultinseriouspersonalinjury.

11. Keep blade sharp and clean. Gum and wood

pitch hardened on blades slows saw and increasespotentialforkickback.Keepbladeclean byrstremovingitfromtool,thencleaningitwith gum and pitch remover, hot water or kerosene. Never use gasoline.

13. Always use the saw blade intended for cutting

the material that you are going to cut.

14. Only use the saw blades that are marked with

a speed equal or higher than the speed marked on the tool.

15. (For European countries only)

Always use the blade which conforms to EN847-1, if intended for wood and analogous materials.

16. Place the tool and the parts on a at and stable

surface.Otherwisethetoolorthepartsmayfall andcauseaninjury. SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity

with product (gained from repeated use) replace strict adherence to safety rules for the subject product. MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. Important safety instructions for battery cartridge

1. Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery.

2. Do not disassemble or tamper with the battery

cartridge.Itmayresultinare,excessiveheat,12 ENGLISH or explosion.

3. If operating time has become excessively

shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion.

4. If electrolyte gets into your eyes, rinse them

out with clear water and seek medical atten- tion right away. It may result in loss of your eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any con- ductive material. (2) Avoid storing battery cartridge in a con- tainer with other metal objects such as nails, coins, etc. (3) Do not expose battery cartridge to water or rain. A battery short can cause a large current ow, overheating, possible burns and even a breakdown.

6. Do not store and use the tool and battery car-

tridge in locations where the temperature may reach or exceed 50 °C (122 °F).

7. Do not incinerate the battery cartridge even if

it is severely damaged or is completely worn out. The battery cartridge can explode in a re.

8. Do not nail, cut, crush, throw, drop the battery

cartridge, or hit against a hard object to the battery cartridge.Suchconductmayresultina re,excessiveheat,orexplosion.

9. Do not use a damaged battery.

10. The contained lithium-ion batteries are subject

to the Dangerous Goods Legislation require- ments. Forcommercialtransportse.g.bythirdparties, forwarding agents, special requirement on pack- aging and labeling must be observed. For preparation of the item being shipped, consult- inganexpertforhazardousmaterialisrequired. Pleasealsoobservepossiblymoredetailed national regulations. Tapeormasko󰀨opencontactsandpackupthe batteryinsuchamannerthatitcannotmove around in the packaging.

11. When disposing the battery cartridge, remove

it from the tool and dispose of it in a safe place. Follow your local regulations relating to disposal of battery.

12. Use the batteries only with the products

specied by Makita. Installing the batteries to non-compliantproductsmayresultinare,exces- siveheat,explosion,orleakofelectrolyte.

13. If the tool is not used for a long period of time,

the battery must be removed from the tool.

14. During and after use, the battery cartridge may

take on heat which can cause burns or low temperature burns. Pay attention to the han- dling of hot battery cartridges.

15. Do not touch the terminal of the tool imme-

diately after use as it may get hot enough to cause burns.

16. Do not allow chips, dust, or soil stuck into the

terminals, holes, and grooves of the battery cartridge.Itmaycauseheating,catchingre, burstandmalfunctionofthetoolorbatterycar- tridge,resultinginburnsorpersonalinjury.

17. Unless the tool supports the use near

high-voltage electrical power lines, do not use the battery cartridge near high-voltage electri- cal power lines.Itmayresultinamalfunctionor breakdownofthetoolorbatterycartridge.

18. Keep the battery away from children.

SAVE THESE INSTRUCTIONS. CAUTION: Only use genuine Makita batteries. Use of non-genuine Makita batteries, or batteries that havebeenaltered,mayresultinthebatterybursting causingres,personalinjuryanddamage.Itwill alsovoidtheMakitawarrantyfortheMakitatooland charger. Tips for maintaining maximum battery life

1. Charge the battery cartridge before completely

discharged. Always stop tool operation and charge the battery cartridge when you notice less tool power.

2. Never recharge a fully charged battery car-

tridge. Overcharging shortens the battery service life.

3. Charge the battery cartridge with room tem-

perature at 10 °C - 40 °C (50 °F - 104 °F). Let a hot battery cartridge cool down before charging it.

4. When not using the battery cartridge, remove

it from the tool or the charger.

5. Charge the battery cartridge if you do not use

it for a long period (more than six months). Important safety instructions for wireless unit

1. Do not disassemble or tamper with the wire-

2. Keep the wireless unit away from young chil-

dren. If accidentally swallowed, seek medical attention immediately.

3. Use the wireless unit only with Makita tools.

4. Do not expose the wireless unit to rain or wet

5. Do not use the wireless unit in places where

the temperature exceeds 50 °C (122 °F).

6. Do not operate the wireless unit in places

where medical instruments, such as heart pace makers are nearby.

7. Do not operate the wireless unit in places

where automated devices are nearby. If oper- ated,automateddevicesmaydevelopmalfunction or error.

8. Do not operate the wireless unit in places

under high temperature or places where static electricity or electrical noise could be generated.

9. The wireless unit can produce electromagnetic

elds (EMF) but they are not harmful to the user.

10. The wireless unit is an accurate instrument. Be13 ENGLISH

careful not to drop or strike the wireless unit.

11. Avoid touching the terminal of the wireless

unit with bare hands or metallic materials.

12. Always remove the battery on the product

when installing the wireless unit into it.

13. When opening the lid of the slot, avoid the

place where dust and water may come into the slot. Always keep the inlet of the slot clean.

on the wireless unit too hard and/or press the button with an object with a sharp edge.

17. Do not remove the wireless unit from the slot

while the power is being supplied to the tool. Doingsomaycauseamalfunctionofthewireless unit.

18. Do not remove the sticker on the wireless unit.

19. Do not put any sticker on the wireless unit.

20. Do not leave the wireless unit in a place where

static electricity or electrical noise could be generated.

21. Do not leave the wireless unit in a place sub-

ject to high heat, such as a car sitting in the sun.

22. Do not leave the wireless unit in a dusty or

powdery place or in a place corrosive gas could be generated.

23. Sudden change of the temperature may bedew

the wireless unit. Do not use the wireless unit until the dew is completely dried.

24. When cleaning the wireless unit, gently wipe

with a dry soft cloth. Do not use benzine, thin- ner, conductive grease or the like.

25. When storing the wireless unit, keep it in the

supplied case or a static-free container.

26. Do not insert any devices other than Makita

wireless unit into the slot on the tool.

damaged. SAVE THESE INSTRUCTIONS. FUNCTIONAL DESCRIPTION CAUTION: Always be sure that the tool is switched o󰀨 and the battery cartridge is removed before adjusting or checking function on the tool. Installing or removing battery cartridge CAUTION: Always switch o󰀨 the tool before installing or removing of the battery cartridge. CAUTION: Hold the tool and the battery car- tridge rmly when installing or removing battery cartridge.Failuretoholdthetoolandthebattery cartridgermlymaycausethemtoslipo󰀨yourhands andresultindamagetothetoolandbatterycartridge andapersonalinjury. CAUTION: Do not use the battery adapter with the circular saw. The cable of the battery adapter may hinder the operation and result in personal injury. ►Fig.7: 1. Red indicator 2. Button 3.Batterycartridge Toremovethebatterycartridge,slideitfromthetool while sliding the button on the front of the cartridge. Toinstallthebatterycartridge,alignthetongueonthe batterycartridgewiththegrooveinthehousingandslip itintoplace.Insertitallthewayuntilitlocksinplace withalittleclick.Ifyoucanseetheredindicatoras showninthegure,itisnotlockedcompletely. CAUTION: Always install the battery cartridge fully until the red indicator cannot be seen. If not, itmayaccidentallyfalloutofthetool,causinginjuryto youorsomeonearoundyou. CAUTION: Do not install the battery cartridge forcibly.Ifthecartridgedoesnotslideineasily,itis notbeinginsertedcorrectly. Tool / battery protection system Thetoolisequippedwithatool/batteryprotectionsys- tem.Thissystemautomaticallycutso󰀨powertothe motortoextendtoolandbatterylife.Thetoolwillauto- maticallystopduringoperationifthetoolorbatteryis placed under one of the following conditions. Overload protection Whenthetool/batteryisoperatedinamannerthat causesittodrawanabnormallyhighcurrent,thetool automaticallystops.Inthissituation,turnthetoolo󰀨 and stop the application that caused the tool to become overloaded. Then turn the tool on to restart. Overheat protection Whenthetool/batteryisoverheated,thetoolstops automatically.Inthissituation,letthetoolcooldown before turning the tool on again. Overdischarge protection Whenthebatterycapacitybecomeslow,thetoolstops automatically.Iftheproductdoesnotoperateeven when the switches are operated, remove the batteries from the tool and charge the batteries.14 ENGLISH Indicating the remaining battery capacity Pressthecheckbuttononthebatterycartridgetoindi- catetheremainingbatterycapacity.Theindicatorlamps light up for a few seconds. ►Fig.8: 1. Indicator lamps 2. Check button Indicator lamps Remaining capacity Lighted O󰀨 Blinking 75% to 100% 50% to 75% 25% to 50% 0% to 25% Charge the battery. Thebattery mayhave malfunctioned. NOTE: Depending on the conditions of use and the ambienttemperature,theindicationmaydi󰀨erslightly fromtheactualcapacity. NOTE:Therst(farleft)indicatorlampwillblinkwhen thebatteryprotectionsystemworks. Adjusting depth of cut CAUTION: After adjusting the depth of cut, always tighten the lever securely. Loosen the lever on the depth guide and move the base up or down. At the desired depth of cut, secure the base bytighteningthelever. For cleaner, safer cuts, set cut depth so that no more thanonebladetoothprojectsbelowworkpiece.Using proper cut depth helps to reduce potential for danger- ousKICKBACKSwhichcancausepersonalinjury. ►Fig.9: 1. Lever Bevel cutting CAUTION: After adjusting the bevel angle, always tighten the lever securely. CAUTION: Remove the side grip (handle) when operating bevel cutting. ►Fig.10: 1.Sidegrip(handle) Loosentheleverandsetforthedesiredanglebytilting accordingly,thentightentheleversecurely. ►Fig.11: 1. Lever Positive stopper The positive stopper is useful for setting the designated anglequickly.Turnthepositivestoppersothatthe arrowonitpointsyourdesiredbevelangle(around 22.5°/45°/56°).Loosentheleverandthentiltthetool base until it stops. The position where the tool base stopsistheangleyousetwiththepositivestopper. Tighten the lever with the tool base at this position. ►Fig.12: 1. Positive stopper Sighting For straight cuts, align the 0° position on the front of the basewithyourcuttingline.For45°bevelcuts,alignthe 45° position with it. ►Fig.13: 1.Cuttingline(0°position)2. Cutting line (45°position) Switch action

WARNING: Before installing the battery car-

tridge into the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released.

WARNING: NEVER defeat the lock-o󰀨 button

by taping down or some other means. A switch with anegatedlock-o󰀨buttonmayresultinunintentional operationandseriouspersonalinjury.

WARNING: NEVER use the tool if it runs when

you simply pull the switch trigger without press- ing the lock-o󰀨 button. A switch in need of repair mayresultinunintentionaloperationandserious personalinjury.ReturntooltoaMakitaservicecenter for proper repairs BEFORE further usage. CAUTION: The tool starts to brake the cir- cular saw blade rotation immediately after you release the switch trigger. Hold the tool rmly to respond the reaction of the brake when releasing the switch trigger. Sudden reaction can drop the tool o󰀨yourhandandcancauseapersonalinjury. Topreventtheswitchtriggerfrombeingaccidentally pulled,alock-o󰀨buttonisprovided.Tostartthetool, depressthelock-o󰀨buttonandpulltheswitchtrigger. Release the switch trigger to stop. ►Fig.14: 1. Switch trigger 2.Lock-o󰀨button NOTICE: Do not pull the switch trigger hard without pressing in the lock-o󰀨 button. This can cause switch breakage. Electric brake This tool is equipped with an electric blade brake. If the toolconsistentlyfailstoquicklystopthecircularsaw blade after switch lever release, have tool serviced at a Makita service center. CAUTION: The blade brake system is not a substitute for blade guard. NEVER USE TOOL WITHOUT A FUNCTIONING BLADE GUARD.

SERIOUS PERSONAL INJURY CAN RESULT.15 ENGLISH

Electronic function Thetoolsequippedwithelectronicfunctionareeasyto operatebecauseofthefollowingfeature(s). Soft start feature Soft start because of suppressed starting shock. ASSEMBLY CAUTION: Always be sure that the tool is switched o󰀨 and the battery cartridge is removed before carrying out any work on the tool. O󰀨set wrench storage Whennotinuse,storetheo󰀨setwrenchasshownin theguretokeepitfrombeinglost. ►Fig.15: 1.O󰀨setwrench Removing or installing circular saw blade CAUTION: Be sure the circular saw blade is installed with teeth pointing up at the front of the tool. CAUTION: Use only the Makita o󰀨set wrench to install or remove the circular saw blade. To remove the circular saw blade, press the shaft lock fullysothatthecircularsawbladecannotrevolveand usetheo󰀨setwrenchtoloosenthehexbolt.Then removethehexbolt,outerange,circularsawblade andring(countryspecic). ►Fig.16: 1. Shaft lock 2.O󰀨setwrench3. Loosen

BOLT COUNTERCLOCKWISE SECURELY. Also be careful not to tighten the bolt forcibly. Slipping your hand from the hex wrench can cause a per- sonal injury.

WARNING: Make sure that the protrusion "a"

on the inner ange that is positioned outside ts into the saw blade hole "a" perfectly. Mounting the circular saw blade on the wrong side can result in the dangerous vibration. For tool with the inner ange for a

15.88 mm hole-diameter saw blade

BOLT COUNTERCLOCKWISE SECURELY. Also be careful not to tighten the bolt forcibly. Slipping your hand from the hex wrench can cause a per- sonal injury.

WARNING: If the ring is needed to mount the

circular saw blade onto the spindle, always be sure that the correct ring for the blade's arbor hole you intend to use is installed between the inner and the outer anges. Use of the incorrect arborholeringmayresultintheimpropermountingof the circular saw blade causing blade movement and severe vibration resulting in possible loss of control duringoperationandinseriouspersonalinjury. Blade guard cleaning When changing the circular saw blade, make sure to also clean the upper and lower blade guards of accu- mulated sawdust as discussed in the Maintenance section.Suche󰀨ortsdonotreplacetheneedtocheck lower guard operation before each use.16 ENGLISH Installing side grip (handle) CAUTION: Always be sure that the side grip is installed securely before operation. CAUTION: Remove the side grip (handle) when operating bevel cutting. If you operate bevel cutting with the side grip (handle), it may touch the workpiece or your body and cause kickback or personal injury. CAUTION: Be careful not to hit your ngers against the side grip (handle) when opening/clos- ing the lower guard. Thesidegrip(handle)ishelpfulforholdingandcarrying the tool. Toinstallthesidegrip(handle),screwthesidegrip securelyonthepositionofthetoolasshowninthe gure. ►Fig.22: 1.Sidegrip(handle) Connecting a vacuum cleaner Optional accessory CAUTION: Be careful not to let the hose entangled with the workpiece.Itmayresultinseri- ouspersonalinjuryduetokickback. NOTE: To prevent the rubber cap from being lost, store it on the front of the tool. NOTE: When not using the vacuum cleaner, attach therubbercapontothedustnozzle. Removetherubbercapfromthedustnozzleandcon- nect the vacuum cleaner's hose as illustrated. ►Fig.23: 1. Rubber cap ConnectaMakitavacuumcleanertoyourtool. ►Fig.24: 1. Rubber cap 2. Vacuum cleaner 3. Hose 4.Dustnozzle OPERATION Thistoolisintendedtocutwoodproductsonly. RefertoourwebsiteorcontactyourlocalMakitadealer for the correct circular saw blades to be used for the material to be cut. Checking blade guard function Removethebatterycartridge. Set the bevel angle to 0°, and then retract the lower guardmanuallytotheendandreleaseit.Thelower guardisproperlyfunctioningif; — itisretractedabovethebasewithoutanyhin- drance and; — itautomaticallyreturnsandcontactswiththe stopper. ►Fig.25: 1. Upper guard 2. Lower guard 3. Base

4. Stopper 5. Open 6. Close

Ifthelowerguardisnotfunctioningproperly,checkif saw dust is accumulated inside of the upper and lower guards.Ifthelowerguardisnotfunctioningproperly evenafterremovingdust,haveyourtoolservicedata Makita service center. CAUTION: Wear dust mask when performing cutting operation. CAUTION: Be sure to move the tool forward in a straight line gently. Forcing or twisting the tool will result in overheating the motor and dangerous kickback,possiblycausingsevereinjury. NOTE:Whenthebatterycartridgetemperatureis low,thetoolmaynotworktoitsfullcapacity.Atthis time,forexample,usethetoolforalight-dutycutfor awhileuntilthebatterycartridgewarmsupashigh as room temperature. Then, the tool can work to its fullcapacity. ►Fig.26 Holdthetoolrmly.Thetoolisprovidedwithbothafront grip and rear handle. Use both to best grasp the tool. Ifbothhandsareholdingsaw,theycannotbecutby the circular saw blade. Set the base on the workpiece tobecutwithoutthecircularsawblademakingany contact. Then turn the tool on and wait until the circular sawbladeattainsfullspeed.Nowsimplymovethetool forwardovertheworkpiecesurface,keepingitatand advancingsmoothlyuntilthesawingiscompleted. Togetcleancuts,keepyoursawinglinestraightand yourspeedofadvanceuniform.Ifthecutfailstoprop- erlyfollowyourintendedcutline,donotattempttoturn orforcethetoolbacktothecutline.Doingsomaybind the circular saw blade and lead to dangerous kickback andpossibleseriousinjury.Releaseswitch,waitforcir- cular saw blade to stop and then withdraw tool. Realign tool on new cut line, and start cut again. Attempt to avoid positioning which exposes operator to chips and wooddustbeingejectedfromsaw.Useeyeprotection tohelpavoidinjury. Hook CAUTION: Always remove the battery when hanging the tool with the hook. CAUTION: Never hook the tool at high loca- tions or on the surfaces where the tool may lose the balance and fall.Otherwisefallingaccidentmay occurandcauseseriousinjury. CAUTION: Do not pull the tool downward when it is hooked. CAUTION: Use the hanging/mounting parts for their intended purposes only. Using for unin- tendedpurposemaycauseaccidentorpersonal injury. CAUTION: Never hook the tool if the hook is damaged.Otherwisefallingaccidentmayoccurand causeseriousinjury. Thehookisconvenientforhangingthetooltemporarily. Tousethehook,simplyliftuphookuntilitsnapsinto the open position. Whennotinuse,alwayslowerhookuntilitsnapsinto the closed position. ►Fig.27: 1. Hook 2. Open position 3. Closed position17 ENGLISH ►Fig.28 Rip fence (Guide rule) Optional accessory Thehandyripfenceallowsyoutodoextra-accurate straightcuts.Simplyslidetheripfenceupsnugly against the side of the workpiece and secure it in posi- tion with the clamping screw on the front of the base. It also makes repeated cuts of uniform width possible. ►Fig.29: 1.Ripfence(Guiderule)2. Clamping screw WIRELESS ACTIVATION FUNCTION What you can do with the wireless activation function The wireless activation function enables clean and com- fortableoperation.Byconnectingasupportedvacuum cleanertothetool,youcanrunthevacuumcleaner automaticallyalongwiththeswitchoperationofthetool. ►Fig.30 To use the wireless activation function, prepare follow- ing items:

• Awirelessunit(optionalaccessory)

• A vacuum cleaner which supports the wireless activation function The overview of the wireless activation function setting is as follows. Refer to each section for detail procedures.

1. Installing the wireless unit

2. Tool registration for the vacuum cleaner

3. Starting the wireless activation function

Installing the wireless unit Optional accessory CAUTION: Place the tool on a at and stable surface when installing the wireless unit. NOTICE: Clean the dust and dirt on the tool before installing the wireless unit. Dust or dirt maycausemalfunctionifitcomesintotheslotofthe wireless unit. NOTICE: To prevent the malfunction caused by static, touch a static discharging material, such as a metal part of the tool, before picking up the wireless unit. NOTICE: When installing the wireless unit, always be sure that the wireless unit is inserted in the correct direction and the lid is completely closed.

2. Insert the wireless unit to the slot and then close

the lid. Wheninsertingthewirelessunit,aligntheprojections with the recessed portions on the slot. ►Fig.32: 1. Wireless unit 2.Projection3. Lid

Whenremovingthewirelessunit,openthelidslowly. The hooks on the back of the lid will lift the wireless unit asyoupullupthelid. ►Fig.33: 1. Wireless unit 2. Hook 3. Lid After removing the wireless unit, keep it in the supplied case or a static-free container. NOTICE: Always use the hooks on the back of the lid when removing the wireless unit. If the hooks do not catch the wireless unit, close the lid completelyandopenitslowlyagain. Tool registration for the vacuum cleaner NOTE: A Makita vacuum cleaner supporting the wireless activation function is required for the tool registration. NOTE: Finish installing the wireless unit to the tool before starting the tool registration. NOTE: During the tool registration, do not pull the switch trigger or turn on the power switch on the vacuum cleaner. NOTE: Refer to the instruction manual of the vacuum cleaner, too. Ifyouwishtoactivatethevacuumcleaneralongwith theswitchoperationofthetool,nishthetoolregistra- tion beforehand.

1. Install the batteries to the vacuum cleaner and the

3. Press the wireless activation button on the vac-

uum cleaner for 3 seconds until the wireless activation lamp blinks in green. And then press the wireless acti- vationbuttononthetoolinthesameway. ►Fig.35: 1. Wireless activation button 2. Wireless activation lamp If the vacuum cleaner and the tool are linked success- fully,thewirelessactivationlampswilllightupingreen for 2 seconds and start blinking in blue. NOTE:Thewirelessactivationlampsnishblinking in green after 20 seconds elapsed. Press the wireless activation button on the tool while the wireless acti- vation lamp on the cleaner is blinking. If the wireless activation lamp does not blink in green, push the wire- lessactivationbuttonbrieyandholditdownagain. NOTE: When performing two or more tool registra- tionsforonevacuumcleaner,nishthetoolregistra- tiononebyone.18 ENGLISH Starting the wireless activation function NOTE: Finish the tool registration for the vacuum cleaner prior to the wireless activation. NOTE: Refer to the instruction manual of the vacuum cleaner, too. After registering a tool to the vacuum cleaner, the vac- uumcleanerwillautomaticallyrunalongwiththeswitch operation of the tool.

1. Install the wireless unit to the tool.

2. Connect the hose of the vacuum cleaner with the

5. Turn on the tool. Check if the vacuum cleaner runs

while the tool is operating. To stop the wireless activation of the vacuum cleaner, push the wireless activation button on the tool. NOTE: The wireless activation lamp on the tool will stop blinking in blue when there is no operation for 2hours.Inthiscase,setthestand-byswitchonthe vacuum cleaner to "AUTO" and push the wireless activation button on the tool again. NOTE:Thevacuumcleanerstarts/stopswithadelay. There is a time lag when the vacuum cleaner detects a switch operation of the tool. NOTE: The transmission distance of the wireless unit mayvarydependingonthelocationandsurrounding circumstances. NOTE: When two or more tools are registered to onevacuumcleaner,thevacuumcleanermaystart runningevenifyoudonotturnonyourtoolbecause another user is using the wireless activation function. Description of the wireless activation lamp status ►Fig.39: 1. Wireless activation lamp The wireless activation lamp shows the status of the wireless activation function. Refer to the table below for the meaning of the lamp status. Status Wireless activation lamp Description Color

Blinking Duration Standby Blue 2 hours The wireless activation of the vacuum cleaner is available. The lampwillautomaticallyturno󰀨whennooperationisperformed for 2 hours. When the tool is running. The wireless activation of the vacuum cleaner is available and the tool is running. Tool registration Green 20 seconds Readyforthetoolregistration.Waitingfortheregistrationbythe vacuum cleaner. 2 seconds Thetoolregistrationhasbeennished.Thewirelessactivation lamp will start blinking in blue. Cancelling tool registration Red 20 seconds Readyforthecancellationofthetoolregistration.Waitingforthe cancellationbythevacuumcleaner. 2 seconds Thecancellationofthetoolregistrationhasbeennished.The wireless activation lamp will start blinking in blue. Others Red 3 seconds The power is supplied to the wireless unit and the wireless activa- tion function is starting up. O󰀨 - - The wireless activation of the vacuum cleaner is stopped. Cancelling tool registration for the vacuum cleaner Perform the following procedure when cancelling the tool registration for the vacuum cleaner.

1. Install the batteries to the vacuum cleaner and the

3. Press the wireless activation button on the

vacuum cleaner for 6 seconds. The wireless activation lamp blinks in green and then become red. After that, press the wireless activation button on the tool in the sameway. ►Fig.41: 1. Wireless activation button 2. Wireless activation lamp Ifthecancellationisperformedsuccessfully,thewire- less activation lamps will light up in red for 2 seconds and start blinking in blue.19 ENGLISH NOTE:Thewirelessactivationlampsnishblinkingin red after 20 seconds elapsed. Press the wireless acti- vation button on the tool while the wireless activation lamp on the cleaner is blinking. If the wireless acti- vation lamp does not blink in red, push the wireless activationbuttonbrieyandholditdownagain. Troubleshooting for wireless activation function Beforeaskingforrepairs,conductyourowninspectionrst.Ifyoundaproblemthatisnotexplainedinthemanual, donotattempttodismantlethetool.Instead,askMakitaAuthorizedServiceCenters,alwaysusingMakitareplace- ment parts for repairs. State of abnormality Probable cause (malfunction) Remedy The wireless activation lamp does not light/blink. The wireless unit is not installed into the tool. Thewirelessunitisimproperlyinstalled into the tool. Installthewirelessunitcorrectly. The terminal of the wireless unit and/or theslotisdirty. Gentlywipeo󰀨dustanddirtontheterminalofthe wireless unit and clean the slot. The wireless activation button on the tool has not been pushed. Push the wireless activation button on the tool briey. Thestand-byswitchonthevacuum cleaner is not set to "AUTO". Setthestand-byswitchonthevacuumcleanerto "AUTO". Nopowersupply Supplythepowertothetoolandthevacuum cleaner. Cannotnishtoolregistration/can- cellingtoolregistrationsuccessfully. The wireless unit is not installed into the tool. Thewirelessunitisimproperlyinstalled into the tool. Installthewirelessunitcorrectly. The terminal of the wireless unit and/or theslotisdirty. Gentlywipeo󰀨dustanddirtontheterminalofthe wireless unit and clean the slot. Thestand-byswitchonthevacuum cleaner is not set to "AUTO". Setthestand-byswitchonthevacuumcleanerto "AUTO". Nopowersupply Supplythepowertothetoolandthevacuum cleaner. Incorrect operation Pushthewirelessactivationbuttonbrieyand perform the tool registration/cancellation procedures again. Thetoolandvacuumcleanerareaway fromeachother(outofthetransmission range). Get the tool and vacuum cleaner closer to each other. The maximum transmission distance is approximately10mhoweveritmayvaryaccording to the circumstances. Beforenishingthetoolregistration/ cancellation; - the switch of the tool is turned on or; - the power button on the vacuum cleaner is turned on. Pushthewirelessactivationbuttonbrieyand perform the tool registration/cancellation procedures again. The tool registration procedures for the tool or vacuum cleaner have not nished. Perform the tool registration procedures for both the tool and the vacuum cleaner at the same timing. Radiodisturbancebyotherappliances whichgeneratehigh-intensityradio waves. Keepthetoolandvacuumcleanerawayfromthe appliances such as Wi-Fi devices and microwave ovens.20 ENGLISH State of abnormality Probable cause (malfunction) Remedy The vacuum cleaner does not run along with the switch operation of the tool. The wireless unit is not installed into the tool. Thewirelessunitisimproperlyinstalled into the tool. Installthewirelessunitcorrectly. The terminal of the wireless unit and/or theslotisdirty. Gentlywipeo󰀨dustanddirtontheterminalofthe wireless unit and clean the slot. The wireless activation button on the tool has not been pushed. Pushthewirelessactivationbuttonbrieyandmake sure that the wireless activation lamp is blinking in blue. Thestand-byswitchonthevacuum cleaner is not set to "AUTO". Setthestand-byswitchonthevacuumcleanerto "AUTO". More than 10 tools are registered to the vacuum cleaner. Perform the tool registration again. If more than 10 tools are registered to the vacuum cleaner, the tool registered earliest will be cancelled automatically. The vacuum cleaner erased all tool registrations. Perform the tool registration again. Nopowersupply Supplythepowertothetoolandthevacuum cleaner. Thetoolandvacuumcleanerareaway fromeachother(outofthetransmission range). Get the tool and vacuum cleaner closer each other. The maximum transmission distance is approxi- mately10mhoweveritmayvaryaccordingtothe circumstances. Radiodisturbancebyotherappliances whichgeneratehigh-intensityradio waves. Keepthetoolandvacuumcleanerawayfromthe appliances such as Wi-Fi devices and microwave ovens. The vacuum cleaner runs while the tool is not operating. Other users are using the wireless activation of the vacuum cleaner with their tools. Turno󰀨thewirelessactivationbuttonoftheother tools or cancel the tool registration of the other tools. MAINTENANCE CAUTION: Always be sure that the tool is switched o󰀨 and the battery cartridge is removed before attempting to perform inspection or maintenance. CAUTION: Clean out the upper and lower guards to ensure there is no accumulated saw- dust which may impede the operation of the lower guarding system.Adirtyguardingsystemmaylimit the proper operation which could result in serious personalinjury.Themoste󰀨ectivewaytoaccomplish this cleaning is with compressed air. If the dust is being blown out of the guards, be sure the proper eye and breathing protection is used. CAUTION: After each use, wipe o󰀨 the saw dust on the tool.Finesawdustmaycomeinsidethe toolandcausemalfunctionorare. NOTICE: Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result. To maintain product SAFETY and RELIABILITY, repairs,anyothermaintenanceoradjustmentshould beperformedbyMakitaAuthorizedorFactoryService Centers,alwaysusingMakitareplacementparts. Adjusting 0°-cut accuracy Thisadjustmenthasbeenmadeatthefactory.Butifitis o󰀨,youcanadjustitasthefollowingprocedure.

3. Tighten the lever and then make a test cut to

check the verticalness. OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specied in this manual.Theuseofanyother accessories or attachments might present a risk of injurytopersons.Onlyuseaccessoryorattachment for its stated purpose. Ifyouneedanyassistanceformoredetailsregard- ingtheseaccessories,askyourlocalMakitaService Center.

WAARSCHUWING: ZORG ERVOOR DAT U

WAARSCHUWING: ZORG ERVOOR DAT U

rior 5. Perno hexagonal