CPWD290X - Water dispenser CANDY - Free user manual and instructions

Product type	Water dispenser with filtration, UV sterilization, refrigeration, heating, and carbonation
Brand and model	Candy CPWD290X
Power supply	220-240 V ~ 50/60 Hz (typical value, not specified in the manual)
Required water pressure	2.0 to 3.5 bar
Maximum ambient temperature	45 °C
Types of water dispensed	Still water (room temperature), cold water (1-10 °C adjustable), hot water (50-85 °C adjustable), cold sparkling water
Filtration technology	Pre-filter (fabric) + composite filter (activated carbon, etc.) + UV lamp
Tank capacity	Not specified; typical estimate: 2-3 liters
Dispensing flow rate	Programmable from 1 to 30 seconds per dose (user adjustable)
Display and controls	LCD screen with touch keys; user programming
Integrated alarms	Low pressure, filter change, anti-overflow, refrigerator/boiler/carbonator probe
Maintenance and cleaning	Exterior cleaning with damp cloth and mild detergent; do not use abrasive products
Pre-filter replacement	Every 6 months (by user)
Composite filter replacement	Every 12 months (by technical service)
UV lamp replacement	Every 7000 hours or as indicated by alarm (by technical service)
Sanitization	Every 12 months or after 15 days of non-use (by technical service)
CO2 bottle replacement	When bubbles decrease (by user)
Child safety	Use by adults only; keep children away from the appliance
Anti-flood protection	Water leak sensor on the floor; automatic shut-off upon detection
Repairability	Repairs only by authorized technical service; use of original parts
Dimensions (W x H x D)	Not specified; estimate: 30 x 50 x 40 cm (check datasheet)
Weight	Not specified; estimate: approximately 15-20 kg

Frequently Asked Questions - CPWD290X CANDY

How to properly install the Candy CPWD290X dispenser?

Place the appliance on a stable horizontal surface, protected from frost and direct sunlight. Connect it to a drinking water supply with a pressure between 2.0 and 3.5 bar. Ensure good air circulation at the back. Plug into a 220-240 V outlet. For first use, purge the water for at least 5 minutes.

What types of water can I get with this dispenser?

You can get four types of water: still water at room temperature, cold water (adjustable from 1 to 10 °C), hot water (adjustable from 50 to 85 °C), and cold sparkling water (carbonated).

How to adjust the temperature of cold or hot water?

Press keys 2 and 3 simultaneously to enter programming mode. Then use the menu to adjust the refrigerator temperature (1 to 10 °C) or the heating temperature (50 to 85 °C). Confirm with the validation key.

How to change the pre-filter?

The pre-filter must be replaced every 6 months. Turn off the water supply and power. Unscrew the pre-filter housing, replace the cartridge, and screw back on. Restore water and power, then reset the hour counter in the programming menu.

What to do if the screen shows 'Filter Alert'?

This alarm indicates that the pre-filter has reached its maximum life (500 dispensing hours). Replace the pre-filter, then reset the operating hours in the programming menu (keys 2 and 3, then option 'Visualization / reset hours').

How to clean the dispenser?

Use a soft cloth dampened with warm water and a mild detergent. Never use abrasive products, steel wool, or sprays directed at the air intakes. Disconnect the appliance before any internal cleaning.

What to do in case of water leakage under the appliance?

The appliance is equipped with an anti-flood sensor. If it detects water, an audible alarm sounds and dispensing is blocked. Turn off the appliance, dry the area, and ensure the sensor is in contact with the floor. Turn back on to reset.

How often should I change the UV lamp?

The UV lamp must be replaced every 7000 hours of operation, or immediately if the message 'UV LIGHT OFF' appears during dispensing. This operation must be performed by an authorized technical service.

Why does the sparkling water lack bubbles?

This usually indicates that the CO2 bottle is nearly empty. Replace it with a new one. Also check that the water pressure is sufficient (between 2 and 3.5 bar) and that the carbonator is working correctly.

How to disable the audible alarm?

Most alarms can only be stopped by resolving the issue or turning off the appliance. For some alarms like 'Probe Alert', pressing a key may temporarily mute the sound. Refer to the alarm table in the manual for each case.

USER MANUAL CPWD290X CANDY

INSTALLATION, USE AND MAINTENANCE MANUAL

GB

WATER DISPENSER

PT

LIVRO DE INSTRUÇÉS PARA USO E MANUTENÇÃO

DE

Manufacturer is member of WATER QUALITY ASSOCIATION

It is fundamental that this instruction manual is stored together with the equipment for any future consultation. In case the equipment is sold or given to third parties, make sure that this instruction manual is given to the new user, in order to allow him/her to get all necessary information on the equipment operation and relevant notices.

Before using the equipment, carefully and thoroughly read this manual.

Being aware of all the information and prescriptions contained in this manual is of fundamental importance to correctly use the equipment.

These symbols will help you find in a quick way most important information.

Safety information Useful advices and suggestion

Information on environment protection

DECLARATION OF CONFORMITY

The equipment complies with the following standards

for parts that get in contact with food substances, it complies with the prescription of the EEC Directive 89/109 and of the law by decree n.108 of 25/01/92;
to what prescribed by the EEC Directives 73/23 (Low Tension), 89/336 (Electromagnetic Compatibility), including the latest modifications introduced by the EEC Directives 93/68, 90/396 and further modifications.

This equipment complies with the safety norm IMQ-CSv

This equipment is fitted with components complying with NSF norms ( Food products )

Manufacturer is member of WATER QUALITY ASSOCIATION

CE mark validity is subject to the product integrity and to the respect of the assembly conditions and use indicated in the installation, use and maintenance manual. Any unauthorized modifications will cause the lost of the CE marking.

FOR YOUR SAFETY

These notices have been issued for the safety of yourself and of anyone who could use your new electrical appliance (Water dispenser). For this reason we recommend to carefully read them before installing and using the equipment.

Children safety

• The Dispenser must be used only by adults. Make sure that children neither touch push buttons nor play with the Dispenser.

During the use i

• The Dispenser is for domestic use. Make sure not to use it for any other purpose. Any other use is considered as unsuitable. The manufacturer declines any responsibility for damages caused by a wrong or unsuitable use.
• Make sure to have a good air circulation around the Dispenser. Avoid to obstruct side and rear cooling air intake.
• Check that there are no leakages from the hydraulic system close to the Dispenser. These could cause a short circuit.

Cleaning and maintenance

• To carry out periodic cleaning use a soft moistened cloth with water and mild detergent or specific products for stainless steel
• Never use wire wools or blades to remove any possible scales.
• Always avoid to use abrasive products.
• Before carrying out any extraordinary maintenance, verify that the Dispenser is not connected to the electric main.
• Keep the Dispenser always perfectly clean.
• Pay particular attention when using spray cleaning products: always make sure not to spray towards the air intakes.
• In case of failure, never attempt to repair the Dispenser yourself. Repairs that are carried out by unqualified people could cause damages and accidents. Consult the content of this manual. In case you cannot find information of your interest, get in contact with the nearest service center. Service to the Dispenser must be carried out by an authorized service center. Do not have the equipment repaired by non specialized personnel
• Always require original spare parts. Only the use of original spare parts could guarantee the reliability and the best performance of the equipment.

Disposal - Packing

• All materials are compatible with the environment and can be recycled. We would like to ask you to contribute the environment protection by using the proper channels for the correct waste disposal.

EEC Directive 2002/96/CE

This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE).

By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.

The symbol on the product indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment

Disposal must be carried out in accordance with local environmental regulations for waste disposal.

For more detailed information about treatment, recovery and recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

• Before disposing of the Dispenser, cut the feeding cable in order to prevent any possible use of it.

The dispenser is designed to use only drinkable water coming from the water supply.

Such a water, after a treatment cycle, is delivered still, cold, sparkling or hot.

Attention: the manufacturer declines any responsibility in case of non drinkable water or of water not controlled by the water company. In such a case, every guarantee will cease.

The treatment cycle is divided in four stages:

(1) PRE-FILTRATION

The inlet water goes through a fabric filter that retains deposits and even rougher suspended solids that could quickly obstruct the second stage of the filtration system.

(2) FILTRATION

The water coming from the pre-filtration system goes through a composite filter that reduces the bacterial charge, eliminates suspended particles, chlorine and organic substances.

(3)STERILIZATION

Thanks to the ultra-violet rays emitted by a UV lamp, any residual bacterial charge in the water coming from the filtration process is eliminated.

(4) COOLING/HEATING/FIZZING

After going through the above mentioned treatment, the water is dispensed at the same inlet temperature (still water), or it can be dispensed cooled (cold still water) or a certain quantity of carbon dioxide is added (cold sparkling water) or it can be warmed (hot still water).

PRECAUTIONS FOR INSTALLATION

• The product must be always installed downstream the autoclave or the water meter and downstream any water filtration or treatment devices (a filtration system is already built-in).
• Always verify that the inlet water is of a controlled origin (drinkable).
• Verify that the main pressure is between 2,0 and 3,5 bar: in case the main pressure is higher than the maximum allowable value, the fizzing procedure could be compromised (in such a case, install a pressure reducer); should the main pressure be lower than the minimum value, the electrical appliance would produce an alarm signal indicating a non sufficient pressure.
• For a correct operation of the refrigerator unit, it is necessary to grant a good air circulation in the back of the equipment and to have a room temperature not exceeding 45^ . Place the equipment in a perfectly horizontal position in order to allow the anti-flood feeler, very useful in case of a possible water leakage, to operate in a correct way (to activate the alarm, the feeler must be completely immersed in water).
• The Dispenser installation and the connection to the electric main, including any modification to the hydraulic system, if required, must be carried out only by qualified personnel.
• Secure the cabinet that holds the water machine to the wall. This will prevent the cabinet from falling forward when pulling out the machine on its guides.
• The Dispenser is heavy; move it very carefully.
• Handle with care, by making sure never to turn it upside down.
• It is forbidden to modify or to attempt to modify the features of the Dispenser.
• The manufacturer declines any responsibility for possible damages caused to people or objects because of possible modifications, accessories or devices of any type installed on the equipment and not expressly foreseen in this manual.
• Make sure to grant a good air circulation around the Dispenser: ask a technician to check that air intakes allow a good air circulation and that they are not obstructed.

STARTUP

WARNING - it is necessary that this operation is carried out by qualified technical people.

• When starting up the unit for the first time, it is necessary to eliminate every type of produced water (still, cold, hot and sparkling) for the first 5 minutes of production in order to eliminate the protection anti-bacterial agent introduced at the end of the testing cycle.

During this stage, the produced water could have an unpleasant smell and/or an altered colour: such symptoms will disappear after the supply of 2 or 3 litres of water that needs to be eliminated.

Warning: in case the equipment is first used in a selling point or during an exhibition, carry out a complete sanitization cycle before installing it for a private user.

TECHNICAL SERVICE

Before calling the Technical Service

In case the equipment would not operate, we suggest to:

• verify that the plug is correctly connected;
• verify that the connection to the hydraulic main is not interrupted and/or obstructed.

In case the causes for the malfunctioning cannot be found, switch off the equipment, do not tamper with it and call the Technical Service.

It is important to communicate the Authorized Technical Service the product model and its serial number (16 digit starting by number 3) that can be found on the guarantee certificate or on the nameplate. In this way, you can contribute to avoid useless transfers of the technician, thus saving relevant costs.

STARTING

After switching the unit on by means of the switch ON/OFF (pag. 37) the following messages appear on the display:

After 3 seconds the following messages are alternatively displayed:

By pressing button

"ON / OFF BOILER" the boiler heating element is activated and the following message is displayed:

Boiler 50 C Filter Change 500 h

The display indicates the temperature of the boiler and the temperature of the refrigerator in Celsius. In case the displayed value is not included in the reading range, 3 lines are displayed.

DRINK SUPPLY

The built-in system foresees 4 types of drinks, with programmable supply (see paragraph "user programming" - pre-set value 15 seconds per each drink):

To stop the supply, press any dosing button. During the supply, four LEDs are switched on.

DRINK	DOSING BUTTON	DISPLAY	NOTE
STILL WATER		Still water UV LIGHT ON	In case “UV LIGHT OFF” is displayed during the supply, this indicates an anomalous operation of the sterilizer. In such a case, get in contact with the technical assistance center.
SPARKLING WATER		Carbonated water UV LIGHT ON
COLD WATER		Cold water UV LIGHT ON
HOT WATER		Hot water UV LIGHT ON

ALARMS

Unless otherwise stated in the column HOW CAN YOU STOP IT, the audible alarm can be switched off only by switching off the appliance.

			HOW CAN YOU STOP ITDIS
Allarm Low Pressure	During the supply, whenever a lack of inlet water or a too low pressure from the main occur.	Intervalli di 0,5 secondi.	The unit will not supply until the problem that has caused the starting of the alarm is solved. By pressing the button, the alarm will be temporarily re-set to allow to solve the inconvenience.
Filter Allarm	Once the supply hours set on the display are reached.	Intervalli da 1 secondo.	This alarm warns the user that it is necessary to replace the pre-filter. After the filter replacement, in order not to have the same message displayed again, set at zero the operating hours (see paragraph user programming).
Anti- ooding Allarm	In case the anti-flood feelers sense a water presence.	Intervalli da 2 secondi.	The unit will not supply until the problem that has caused the starting of the alarm is solved. Switch the unit off and on to reset the alarm. Such an alarm, if leakages are not eliminated and if the inner sensor is not carefully dried, would not allow to start the unit.
Refrigerator probe allarm	In case the unit senses that one of the two feelers are disconnected or in short circuit.	Intervalli di 0,35 secondi.	By pressing a button, the acoustic alarm as well as the message on the LCD are re-set and the unit will not supply the drink associated with the feeler causing the alarm. The alarm is automatically disconnected when the malfunction is eliminated.
Boiler probe allarm
Charge Timeout Allarm	In case, after 180 seconds of filling, the maximum level feeler is not covered	Intervalli da 0,25 secondi.	By pressing a button, the acoustic alarm as well as the message on the LCD are disconnected, the unit will not supply sparkling water. When the unit is started again, the fillin

The system is fitted with components that are subject to periodic replacement and for which it is not possible to foresee the actual life: one of the most important parameter is the quality of the water (the higher the quality of the inlet water, the longer the average life of the component). The components to be replaced can be bought by the technical assistance.

In case of a heavy use, the system will provide to inform the user about the need to replace a certain component subject to periodic replacement.

Instructions for component replacement are supplied together with the component itself.

			NOTEFREQUENCY WAT
6 MONTHS	PREFILTER	USER	By only treating drinkable water with suspended solids not bigger than 5 micron.
12 MONTHS	COMPOSITE FILTER	TECHNICAL ASSISTANCE	By only treating drinkable water with suspended solids not bigger than 5 micron..
12 MONTHS Or in case the unit has not been used for a period longer than 15 days.	SANITIZATION	TECHNICAL ASSISTANCE	The system sanitization must ALWAYS be carried out if the unit has not been used for a period longer than 15 days.
12 MONTHS	WATER SEAL CHECK	TECHNICAL ASSISTANCE	Ultraviolet rays could damage the hydraulic fitting gaskets installed on the sterilizer.
7000 hours	UV LAMP	TECHNICAL ASSISTANCE	The need to replace it is indicated by the system; even if it regularly turns on, it might not be in a position to grant the best sterilization of the discharged water any longer.
In case a remarkable lack of fizzing is noticed when dispensing the drink.	2 BOTTLE	USERCO	It is advisable not to wait the complete consumption.

WHC

USER PROGRAMMING

This paragraph indicates how to modify some parameters of the dispenser, such as the quantity of water to be supplied every time the buttons are pressed, the refrigerator temperature, and so on. Being very simple, these operations can be carried out very safely by the user.

To enter the programming functions, press buttons 2 and 3 at the same time.

User programming cycle Buttons and allow to scroll the menu. Button allows to modify the parameter. By pressing it for a second time, after modifying the value, it saves the datum.
	VISUALIZATION ON THE DISPLAY	OPERATIONMENU
Visualization / zero setting supplied doses of still water	Total supplied doses [XXXX]	Given value indicates the total number of supplied doses
Visualization / zero setting supplied doses of sparkling water	Still water doses [XXXX]	Given value indicates the total number of supplied doses of still water To set at zero press at the same time buttons
Visualization / zero setting supplied doses of sparkling water	Sparkling water doses [XXXX]	Given value indicates the total number of supplied doses of sparkling water To set at zero press at the same time buttons
Visualization / zero setting supplied doses of sparkling water	Cold water doses [XXXX]	Given value indicates the total number of supplied doses of cold water To set at zero press at the same time buttons
Visualization / zero setting supplied doses of sparkling water	Hot water doses [XXXX]	Given value indicates the total number of supplied doses of hot water To set at zero press at the same time buttons
	VISUALIZATION ON THE DISPLAY	OPERATIONMENU
Refrigerator unit temperature adjustment.	Refrigeration Temperature [5] => C°	“5” indicates the pre-set temperature, in degrees Celsius, of the refrigerator unit; the values can be set between 1 °C and 10°CPress button to allow the modification.Press button and to modify.Press button to save datum and exit.
Boiler temperature adjustment to produce hot water.	Boiler Temperature [85] => C°	“85” indicates the pre-set temperature, in degrees Celsius, of the boiler (to produce hot water); the values can be set between 50°C and 85°C.Press button to allow the modification.Press button and to modify.Press button to save datum and exit.
Still water dosing adjustment	Still water doses [15.0] => sec	“15.0” indicates the length (pre-set) in seconds of the water supply when pressing the supply button.Press button to allow the modification.Press button and to modify.Press button to save datum and exit
Sparkling water dosing adjustment	Sparkling water doses [15.0] => sec	“15.0” indicates the length (pre-set) in seconds of the water supply when pressing the supply button.Press button to allow the modification.Press button and to modify.Press button to save datum and exit
Cold water dosing adjustment	Cold water doses [15.0] => sec	“15.0” indicates the length (pre-set) in seconds of the water supply when pressing the supply button.Press button to allow the modification.Press button and to modify.Press button to save datum and exit
Hot water dosing adjustment	Hot water doses [15.0] => sec	“15.0” indicates the length (pre-set) in seconds of the water supply when pressing the supply button.Press button to allow the modification.Press button and to modify.Press button to save datum and exit

To exit the user programming stage, press buttons 1 and 2 at the same time.

ADVERTÉNCIAS GERAIS

Manufacturer is member of WATER QUALITY ASSOCIATION

WAARSCHUWINGEN VOOR DE INSTALLATIE

INSCHAKELING VAN HET APPARAAT

Manufacturer is member of WATER QUALITY ASSOCIATION

Directive 2002/96/CE

Eau chaude 50^