GK1530X - Electric saw BLACK & DECKER - Free user manual and instructions
Find the device manual for free GK1530X BLACK & DECKER in PDF.
| Product Type | Electric Chainsaw |
| Brand | Black & Decker |
| Model | GK1530X |
| Guide Bar Length | 30 cm |
| Max Cutting Length | 30 cm |
| Rated Power | 1600 W |
| Supply Voltage | 230 V |
| Chain Speed (no load) | 8 m/s |
| Weight | 3.7 kg |
| Oil Tank Capacity | 180 ml |
| Safety Class | II (double insulation) |
| Chain Brake | Automatic kickback and inertia |
| Chain Type | 30 cm chain (ref. A6154) |
| Recommended Oil | Black & Decker chain oil (A6027) |
| Maintenance | Check chain tension every 10 min; clean guide bar and chain regularly |
| Warranty | 24 months |
Frequently Asked Questions - GK1530X BLACK & DECKER
User questions about GK1530X BLACK & DECKER
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Electric saw in PDF format for free! Find your manual GK1530X - BLACK & DECKER and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. GK1530X by BLACK & DECKER.
USER MANUAL GK1530X BLACK & DECKER
Warning! When using electric tools, basic safety precautions should always be taken to reduce the risk of fire, electric shock and personal injury.
Read this user manual carefully, observing all of the recommended safety instructions before, during and after use of your chainsaw. Maintain your chainsaw in good working order. Familiarise yourself with the controls on your chainsaw before attempting to operate it, but above all, be sure you know how to stop the tool in an emergency. Retain this user manual and all other literature supplied for future reference.
SAFETY INSTRUCTIONS
Know your chainsaw. Please read this user manual carefully and familiarise yourself with your chainsaw, in particular with regard to the sawing of round wood. We strongly recommend that first time users practice sawing logs on a saw horse or cradle.
Avoid dangerous environments. Keep your work area clean and remove clutter. Keep the work area well lit. We strongly recommend the use of a sawhorse or cradle whenever possible.
Do not saw wet wood or use your chainsaw when it is raining.
- Keep people away while your chainsaw is in use. Do not allow children, other people or animals near your chainsaw while you are using it.
Maintain your chainsaw when not in use. Do not store your chainsaw for any length of time without first removing the saw chain and guide bar which should be kept immersed in oil. Store all parts of your chainsaw in a dry, secure place out of reach of children. We recommend you drain the oil reservoir prior to storage.
Do not force your chainsaw. It will do the job better and more safely at the rate for which it was intended.
Protective clothing. Wear close fitting and protective clothing including a safety helmet with visor/goggles, ear protectors, safety shoes, protective bib trousers and strong leather gloves.
Do not abuse the cable. Never carry a chainsaw by the cable or jerk it to disconnect the plug from the socket. Keep the cable away from heat, oil or sharp edges. Check the cable frequently for damage.
Secure your work using clamps or chocks. Be sure that you use both hands when operating your chainsaw.
Remove the plug from the mains before changing the work location, adjusting, sharpening or cleaning, changing any accessory such as the chain, or if the cord becomes entangled or damaged.
Adjusting wrenches. Form a habit of checking to see that adjusting wrenches are removed from your chainsaw before starting.
Extension cables. Before use, inspect the extension cable and replace if damaged. When using the tool outdoors, only use extension cables intended for outdoor use. Up to 30m of Black & Decker extension cable can be used without loss of power.
Only use extension cable type HO7RN-F 2 x 1mm^2 as a minimum only.
Stay alert. Never operate your chainsaw when you are tired.
- Check damaged parts. Before further use of your chainsaw, a guard or other part that is damaged should be carefully checked to determine whether it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation.
A guard or other part that is damaged should be properly repaired or replaced by an authorised service agent. Do not use your chainsaw if the switch does not turn it on and off.
Repairs. This tool complies with relevant safety requirements. Repairs should only be carried out by qualified persons using original spare parts; otherwise this may result in considerable danger to the user.
Warning! The use of an accessory or attachment other than those recommended in this user manual may present a risk of personal injury.
For all types of cutting, always hold the saw firmly with both hands, with thumbs and fingers encircling the saw handles. Do not release your grip until your chainsaw has stopped moving.
Be sure of your footing and pre-plan a safe exit from a falling tree or branches.
Use wedges to help control felling and prevent binding the guide bar and saw chain in the cut.
Keep all parts of your body and clothing away from the saw chain when running your chainsaw. Before you switch on make sure your chainsaw is not contacting anything. Do not touch or try to stop a moving saw chain with your hand.
Carry your chainsaw carefully with the mains supply disconnected and with the guide bar and saw chain to the rear and the blade sheath fitted.
Keep your chainsaw clean. Do not allow dirt, oil or sawdust to build up on your chainsaw. Pay particular attention to the air inlet and outlet slots; these must not become clogged. Clean your chainsaw with a dry cloth but do not use any solvents or cleaning fluids.
Saw chain care. Keep the saw chain sharp and snug on the guide bar. Ensure the saw chain and guide bar are clean and well oiled.
Beware of kickback. Kickback is upward/ backward motion of the guide bar that may occur when the nose of the saw chain unexpectedly comes in contact with an object. Hold your chainsaw firmly with both hands when the motor is running.
Use a firm grip with thumbs and fingers encircling the handles and watch carefully what you cut.
Kickback can be caused by:
Striking branches or other objects accidentally with a tip of the saw while the saw chain is moving.
Striking metal, cement or any other hard material near the wood, or buried in the wood.
A dull or loose chain.
Cutting above shoulder height.
Lack of attention when holding or guiding the saw while cutting.
Over-reaching. Keep proper footing and balance at all times and do not overreach.
Do not try to insert into a previous cut, as this could cause kickback. Make a fresh cut every time.
We strongly recommend you do not attempt to operate your chainsaw while in a tree, on a ladder or on any other unstable surface. If you decide to do so, be advised that these positions are extremely dangerous.
- When cutting a branch that is under tension, be alert for spring back so that you will not be struck when the tension is released.
Avoid cutting:
Prepared timber.
Into the ground.
Into wire fences, nails, etc.
Into small sized brush and saplings because slender material may catch the saw chain and be whipped towards you, or pull you off balance.
Do not use your chainsaw above shoulder height.
Ensure someone is nearby (but at a safe distance) in case of an accident.
If for any reason you have to touch the chain, make sure your chainsaw is disconnected from the mains.
- The noise from this product can exceed 85 dB(A). We therefore recommend you take appropriate measures for the protection of hearing.
Warning symbols on your chainsaw
Read all of this manual carefully.
ENGLISH
Do not use your chainsaw in wet conditions or expose it to rain.
Always wear ear and eye protection.
Always remove the plug from the socket before inspecting a damaged cable. Be careful not to use your chainsaw if the cable is damaged.
To ensure continued safe operation, check the chain tension as described in this manual after every 10 minutes of use, and adjust back to 3mm as required.
Double insulation
Your chainsaw is double insulated. This means that all external metal parts are electrically isolated from the power supply. This is achieved by placing an extra insulation barrier between the electrical and mechanical parts. Double insulation means greater electrical safety and obviates the necessity of having the machine earthed.
Electrical safety
Make sure your chainsaw is correct for your supply. The voltage can be found on the rating plate.
Technical data
| Bar length 30 cm 35 cm 40 cm | |||
| Supply voltage (V) 230 230 230 | |||
| Rated input (W) 1600 1600 1600 | |||
| Max. cutting length (cm) 30 35 40 | |||
| Chain speed (no load m/s) 8 8 8 | |||
| Weight (kg) | 3.7 | 3.8 | 3.9 |
| Oil capacity (ml) | 180 | 180 | 180 |
| Safety class | II | II | II |
OVERVIEW (fig. A)
- On/off switch
- Lock-off button
- Oil cap
-
Oil level indicator
-
Front guard/chain brake
- Chain cover
- Control knob
- Guide bar
- Chain
- Chain sheath
ASSEMBLY
Before assembly, make sure that the tool is switched off and unplugged.
Oiling the chain (fig. A)
You must do this whenever you use a new chain for the first time. Take the new chain out of its plastic bag and soak it in chain oil for at least an hour before using it. Use Black & Decker chain oil (cat. no. A6027).
We recommend that you use only one brand of oil during the lifetime of your chainsaw because mixtures of different oils could lead to the oil becoming degraded, which can drastically shorten the lifetime of the saw chain.
- Never use waste oil, thick oil or very thin sewing machine oil. These may damage your chainsaw.
Fitting the guide bar and chain (fig. B & C)
Always wear protective gloves when working on your chainsaw and ensure that the plug is not in the electrical outlet.
Fit the saw chain (9) over the guide bar (8), making sure that the cutters are the right way round and that the slider tensioner (11) is facing towards you (fig. B).
With the tool horizontal on a stable surface, put the bar and chain onto the bar mounting studs (13), ensuring the chain is around the drive sprocket (12). Make sure that the cutters on the upper part of the guide bar face towards the front (fig. B).
Before fitting the chain cover check that the cam (18) is in the correct position. If necessary, press and turn the control knob (7) clockwise to rotate the cam into the correct position.
Fit the chain cover by locating the bolt and using the control knob (7) to tighten the chain cover finger tight. To tension the chain, loosen the control knob one full turn, press in firmly and rotate clockwise. As the bar moves forward make sure that the chain links feed into the guide bar. When the control knob stops rotating apply further light pressure. Do not over-tension. Allow the control knob to spring back to the "out" position and rotate further clockwise to tighten the guide bar. Apply moderate pressure to tighten.
Checking and adjusting the chain tension (fig. D)
Before use and after every 10 minutes of use, you must check the chain tension.
Check the chain tension. The tension is correct when the chain snaps back after being pulled 3mm away from the chain bar with light force from the middle finger and thumb. There should be no "sag" between the guide bar and chain on the underside.
Note: Do not over-tension the chain as this will lead to excessive wear and will reduce the life of the bar and chain.
Note: When the chain is new, check the tension frequently (after disconnecting from the mains) during the first 2 hours of use as a new chain stretches slightly.
USE
Let the tool work at its own pace.
Do not overload.
Filling oil into the reservoir (fig. E)
Remove the oil cap (3) and fill the reservoir with the recommended chain oil. You can see the oil level in the indicator slot (4). Refit the oil cap.
Periodically switch off and check the oil in the indicator; if it is less than a quarter full, disconnect your chainsaw from the mains and refill with the correct oil.
Auto-stop chainbrake (fig. F & G)
This tool is fitted with an auto-stop chainbrake which will stop the chain within 150 ms each time you release the rear trigger, or if kickback should occur. This brake should be tested before every use.
How to set the chainbrake
Make sure that the tool is disconnected from the mains supply.
Pull the front guard (5) back into the "set" position
The tool is now ready to use.
How the anti-kickback chainbrake works
In the event of kickback, your left hand comes in contact with the front guard, pushing it backwards, and stops the tool within 150 ms.
How the inertia activated chainbrake works
The chainbrake is activated when the front hand guard is pushed forward, either manually, by the back of the users hand or by its own weight. The advantage of the inertia brake is that it is activated by a severe kickback, eg. when the chain hits metal, even if the users hand does not contact the front guard, ie. when the saw is in the felling position.
How to test the anti-kickback chainbrake
Grip the tool firmly in both hands on a firm surface - make sure the chain is clear of the ground and switch on (see „How to switch your chainsaw on").
- Rotate your left hand forward around the front handle so that the back of your hand comes in contact with the front guard and pushes it backwards (fig. G). The chain should stop within a few fractions of a second.
To reset after the operation of the chainbrake
Follow the instructions for setting the chainbrake.
Notes:
- It will not be possible to switch the tool on if the front guard is not in the "set" position.
Avoid re-starting the tool until you hear the motor come to a complete rest.
ENGLISH
If the chain does not come to rest immediately then this indicates that it needs tensioning (see „Fitting the guide bar and chain").
How to switch the tool on (fig. A)
Grip your chainsaw firmly with both hands. Push the lock-off button (2) forward and then push the on/off switch (1) to start.
- When the motor starts, remove your thumb from the lock button and grip the handle firmly. Do not force the tool - allow it to do the work. It will do a better and safer job at the speed for which it is designed. Excessive force will stretch the chain.
If the saw chain or bar becomes jammed:
Switch the tool off.
Disconnect the tool from the mains supply.
Open the cut with wedges to relieve the strain on the guide bar. Do not try to wrench the saw free. Start a fresh cut.
Felling (fig. H-J)
Pre-plan a safe exit from falling trees or branches.
Cut one third of the diameter of the tree (Fig. H). Then cut down from above to make a notch of about 45^ . This way you will avoid pinching the saw.
Make a single felling cut from the other side but stop before you cut through to the notch (fig. 1).
Drive a wedge or wedges into the felling cut to open it and drop the tree (fig. J).
Logging (fig. K - M)
How you should cut depends on how the log is supported. Use a saw horse whenever possible. Always start a cut with the chain running and the spiked bumper (17) in contact with the wood (fig. K). To complete the cut use a pivoting action of the spiked bumper against the wood.
When supported along its whole length
Make a downward cut, but avoid cutting the earth as this will blunt your saw quickly.
When supported at both ends
First, cut one third down to avoid splintering and second, cut again to meet the first cut.
When supported at one end
First, cut one third up to avoid splintering and second, cut down to prevent splintering.
When on a slope (fig. L)
Always stand on the uphill side.
When using a saw horse (fig. M)
This is strongly recommended whenever possible.
Position the log in a stable position. Always cut on the outside of the saw horse arms.
MAINTENANCE (fig. N)
Regular maintenance ensures a long effective life for the tool. We recommend you make the following checks on a regular basis.
TROUBLESHOOTING
If the tool does not operate correctly, check the following.
Fault Possible cause Action
Tool will not start. Blown fuse. Replace fuse.
Tripped RCD. Check RCD.
Mains lead not connected. Check mains supply.
Tool will not start
button will not slide. Front guard in the brake position Reset front guard.
Chain does not stop instantly
when the tool is switched off. Chain tension is too slack. Check chain tension.
Bar/chain appear hot/smoking. Oil tank empty. Check oil tank level.
Chain tension is too tight. Check chain tension.
Guide bar sprocket nose needs greasing.
Oil level
The level in the reservoir should not be allowed to fall below a quarter full.
Chain and guide bar
After every few hours of use, remove the guide bar and chain and clean thoroughly.
Ensure the hole between the tensioning/oil hole (18) and the bar groove is clear.
On reassembling, the guide bar should be turned through 180^ and the sprocket nose greased via the sprocket lubrication hole (19). This ensures an even distribution of wear around the guide bar rails.
To turn the guide bar through 180^ remove the small screw from the slider and re-fasten to the opposite side of the bar.
Saw chain sharpening
If you are to get the best possible performance from the tool it is important to keep the teeth of the saw chain sharp. Guidance for this procedure is found on the sharpener package. For this purpose we recommend the purchase of the Black & Decker saw chain sharpening kit (available from Black & Decker service agents and selected dealers).
Replacing worn out chains
Replacement chains are available through retailers or Black & Decker service agents. Always use genuine spare parts.
Saw chain sharpness
The cutters will blunt immediately if they touch the ground or a nail whilst cutting.
Saw chain tension
Regularly check the chain tension.
Oil level
Topupiflow.
What to do if your chainsaw needs repair
Your chainsaw is in accordance with the relevant safety requirements. Repairs should only be carried out by a qualified persons using original spare parts, otherwise this may result in considerable danger to the user.
We recommend you keep this user manual in a safe place.
ACCESSIONS
Cat. no. Description
A6154 300mm / 12 chain
A6155 350~mm / 14" chain
A6156 400 mm / 16" chain
A6039 Sharpening kit
A6027 0.5 l chain oil
Protecting the environment
Separate collection. This product must not be disposed of with normal household waste.
Should you find one day that your Black & Decker product needs replacement, or if it is of no further use to you, do not dispose of it with household waste. Make this product available for separate collection.
Separate collection of used products and packaging allows materials to be recycled and used again. Re-use of recycled materials helps prevent environmental pollution and reduces the demand for raw materials.
Local regulations may provide for separate collection of electrical products from the household, at municipal waste sites or by the retailer when you purchase a new product.
Black & Decker provides a facility for the collection and recycling of Black & Decker products once they have reached the end of their working life. To take advantage of this service please return your product to any authorised repair agent who will collect them on our behalf.
ENGLISH
You can check the location of your nearest authorised repair agent by contacting your local Black & Decker office at the address indicated in this manual. Alternatively, a list of authorised Black & Decker repair agents and full details of our after-sales service and contacts are available on the Internet at: www.2helpU.com
Guarantee
Black & Decker is confident of the quality of its products and offers an outstanding guarantee. This guarantee statement is in addition to and in no way prejudices your statutory rights.
The guarantee is valid within the territories of the Member States of the European Union and the European Free Trade Area.
If a Black & Decker product becomes defective due to faulty materials, workmanship or lack of conformity, within 24 months from the date of purchase, Black & Decker guarantees to replace defective parts, repair products subjected to fair wear and tear or replace such products to ensure minimum inconvenience to the customer unless:
The product has been used for trade, professional or hire purposes;
The product has been subjected to misuse or neglect;
The product has sustained damage through foreign objects, substances or accidents;
Repairs have been attempted by persons other than authorised repair agents or Black & Decker service staff.
To claim on the guarantee, you will need to submit proof of purchase to the seller or an authorised repair agent. You can check the location of your nearest authorised repair agent by contacting your local Black & Decker office at the address indicated in this manual. Alternatively, a list of authorised Black & Decker repair agents and full details of our after-sales service and contacts are available on the Internet at: www.2helpU.com
Please visit our website
www.blackanddecker.co.uk to register your new Black & Decker product and to be kept up to date on new products and special offers.
Further information on the Black & Decker brand and our range of products is available at www.blackanddecker.co.uk
EC DECLARATION OF CONFORMITY
GK1640T/GK1635T/GK1630T series
Black & Decker declares that these products conform to:
98/37/EC, 89/336/EEC, EN 50144, EN 55014
2000/14/EC, Chainsaw ≤ 1600 W, Annex V
Level of sound pressure, measured according to 2000/14/EC:
L_pA (sound pressure) dB(A) 88
L_WA (acoustic power) dB(A) 101
L_WA (guaranteed) dB(A) 103
Always wear ear protection if the sound pressure exceeds 85 dB(A).
Hand/arm weighted vibration value according to EN 50144:
3.5 m/s²
Kevin Hewitt
Director of Consumer Engineering
Spennymoor, County Durham DL16 6JG,
United Kingdom
KETTENSÄGE
Director of Consumer Engineering
Spennymoor, County Durham DL16 6JG
United Kingdom
TRONCONNUSE
Spennymoor, County Durham DL16 6JG, United Kingdom
KETTINGZAAG
Ken uw hettingzaag
(onbelast, m/s) 8 8 8
Director of Consumer Engineering
Spennymoor, County Durham DL16 6JG,
United Kingdom
MOTOSIERRA
Spennymoor, County Durham DL16 6JG
United Kingdom
ELECTROSSERRA
Spennymoor, County Durham DL16 6JG
United Kingdom
KEDJESAG
Kevin Hewitt
Director of Consumer Engineering
Spennymoor, County Durham DL16 6JG, United Kingdom
KJEDESAG
VEDLIKEHOLD (fig. N)
Director of Consumer Engineering
Spennymoor, County Durham DL16 6JG
United Kingdom
KAEDESAV
Kend din kaedesav
Reservedele / reparationer
98/37/EØF, 89/336/EØF,
EN 50144, EN 55014,
2000/14/EØF, kaedesav ≤ 1600 W, Annex V
Lydniveauet malt i henhold til 2000/14/EØF:
L_pA (lydniveau) dB(A) 88
L_W (akustisk styrke) dB(A) 101
L_WA (garanteret) dB(A) 103
Director of Consumer Engineering
Spennymoor, County Durham DL16 6JG
United Kingdom
KETJUSAHA
Tunne ketjusahasi
Kevin Hewitt
Director of Consumer Engineering
Spennymoor, County Durham DL16 6JG, United Kingdom
AAYΣΟΠΡΙΝΟ
VwpiTe to aluonpiovoc
Poooxn!KaTaTnXpOnnNkiv
epyaIaw,0a npEnI navta va laabovvra
oi Baikc npoUalaEic aopaaliaic, yia
Tov nepiopioTou kivduvou npkayiac,
nEKTponlIac kalomegaTKwBaaWv.
AiaBaOTe npooekTiká auto To EvyEipidio Xpnoç, akoLouθwVtac oLec TIC ouviotwuevEc odnyiec aoapaaleiac npiv, KaTa TnV diApkeia kai μeTa TnV xpnon Tou aluooPiovou. DiatnpeiTe to aluooPiovocac oK kaln kaTaoan. Vwpiote kaLuTepa Touc diakontec oTo aluooPiovo npiv npoonahtse va To λeIToupynoTe, aλa npo navtoc va yywiTe πwC va To θeote ektoC λeIToupyiaC oε npiTTwoN ektaTnc avayKnC. DuλaEte auto To Evyepilo xpnoc kai ola ta aλla eyypapa nou napexovtal μe auto yia μeAiovTkni avapopá.
O△HΓIEΣAΣΦΑΛΕΙΑΣ
Vwpiote to aUoonpiovo oac. AiaBaoTe npooektiká auto to eYxepidio xphongkai yywpiote kautepa to aUoonpiovo, iiaitepa oov apopa stnv konn otpoyyuau Eulou. Suotnvctai ooi xpnoiopoiouv aUoonpiovo yia npwn pfopa va eEaoknOouv stnv konn Kopuw navw oe KabaAeTo n ikipwa.
AIOpeUyTe ENIkivduva NepiBaALovTa.
DiatnpTe Tov Xwpo EpyaiaC kaHapo KaI
ΦpovTiOTe va mnu unapxouv Emuδia.
ΦpovTiTe o xwpoEpyaiaC va eiva KaLa
ΦwTouEvoc. ZuOtnVetai va xpnoJonoiete
Eva KaBaaTo n Ikpiwa onote evai duvaTo.
Mnv KOBETe BpEymuo Kai myn Xpnouoite To aUosopiovo otav Bpexi.
Mny apnve ta aToa va nnaouv otav To aauoipovo evai eIoupyia.
Mny eitpenei ta e naia, aaaa atoana n zwa kovta oTo aauooppioo otav to xpoioie.
AtnpieTo aauoonpiovo oac 0ka n kaataoOn otavdelta To xpoaumoiite. Otav pfalaosTe to aauoonpiovo oac yia eya lo xpvikó diaoTma npenla va apaipeite Tnv aluaia kai tnv mnapa obnyou kai va t a pfalaosTe meoa e ae lai. DuAeTe oLa taepn tou aauoonpiovou e Enpo, aoaaln xwpo maekia ano naia. Suviotatai va otpayyioet To doxieio laio npiv ano tnv pfala.
Mny zoipzETo aUooonpiovo oac. Oa
AeIoupynoeI kautepa kai aopaaleoTepa eav
XpoaipoonoiOe i ouqwva u TNC
PpOdiaypapcTou.
PpOToTaTeUtiKa poUxa. Na pOpaTe OTeVakai PpOToTaTeUTiKa poUxaounepiauBavovou KpavoucaoaIiaC ME npooWnIDa/ npOToTeUTiKa yuaia, wtaonidc, unoHmuataaoaIiaC, npOToTaTeUTiKec fOpuec kai Yepa dEprativa yavTia.
Mn kaoketaxeipzoeTo kaiwio. Note m np Taepet To aauoonpiovo KpatwtaC To ano To kaiwio kai mV To Tpaatae ano To kaiwio yia va to byaTe ano mV npizc. Povtiote To kalwo va napaevi maekia ano tn thepouTt, ta laia kai ano aixnpes c akec. EeyTe To kaiwio ouxva yia tuxov opec.
Σηριξετο τεμαχIo xρησιμοιωντac σφιγκτήρες ἡκους. Bεβαιωθείτε ὄτι xρησιμοιείτε και τα δύo χέρia ὄταν xειρίζεστε το αλυσοπρiovo.
ByaTe to uma ano TnV npiZa npiv aaaaTe 0eon epyaoiaac,putheta, akovioTe n kaapioTe, aalaTe kanoio eAptnua onwC Tnv aluoi da n av to kaawio mIeXtei n phapei.
EAAHNIKA
Kεiδia puθμiΩnc. Suvnθiσe va ελéγxετe ΘI Ta Kεiδia puθμiΩnc δεν βρικovtai navω ΘO aλuσοπpiovo πiv Εκινησε.
Kaawia npoektaonc. Piv Tn xpno, EiEwpoTTo Kaawio Eiunkuvoc Kai avikataoTto,av exe i 0apéi.Eav xpoumonoiTe Tn ouokun o unaiopio xwpo, xpoumonoiTe movo Kaawia eumukvoc kaatalanla yia xpno n o e unaiopio xwpo. Mnpoei va xpoumonoiTheta Kaawio npoektaonc Black & Decker ewc kai 30 utpwv xwpic va npokntheta anawla 1oxuc.
Spennymoor, County Durham DL16 6JG
United Kingdom
| België/Belgique Black & Decker (Belgium) N.V. Tel. 016 68 91 00Nieuwlandlaan 321 Fax 016 68 91 113200 Aarschot | ||||
| Danmark Black & Decker Tel. 70 20 15 10Sluseholmen 2-4, 2450 København SV Fax 70 22 49 10Internet: www.blackanddecker.dk | ||||
| Deutschland Black & Decker GmbH Tel. 06126/21 - 0Black & Decker Str. 40, D - 65510 Idstein Fax 06126/21 29 80 | ||||
| Ελλάδα Black & Decker (Ελλάς) A.E. Σηλ. 210 8981616Στράβωνος 7 & Αεωφ. Bouλιαγμένης 159Φαζ 210 8983285166 74 Γλυράδα - Αθήναwww.blackanddecker.eu | ||||
| EspanaParc de Negocis "Mas Blau"Edificio Muntadas, c/Bergadá, 1, Of. A608820 El Prat de Llobregat (Barcelona) | ||||
| FranceB.P. 21, 69571 Dardilly Cédex | Black & Decker (France) S.A.S.Fax 04 72 20 39 00 | Tel. | 934 797 400 | |
| HelvetiaGwerbezone Seeblick3213 Kleinössingen | ROFO AGFax 026-6749394 | Tel. | 026-6749391 | |
| ItaliaViale Elvezia 220052 Monza (MI)Numero verde 800-213935 | Black & Decker Italia SpAFax 039-2387592/2387594 | Tel. | 039-23871 | |
| NederlandJoulehof 12, 4622 RG Bergen op Zoom | Black & Decker BeneluxFax 0164 - 283100 | Tel. | 0164 - 283000 | |
| NorgePostboks 4814, Nydalen, 0422 OsloInternet: www.blackanddecker.no | Black & Decker (Norge) A/SFax 22 90 99 01 | TIf. | 22 90 99 00 | |
| ÖsterreichOberlaerstraße 246, A1100 Wien | Black & Decker Vertriebsges.m.b.H Tel. 01 66116-0Fax 01 66116-14 | |||
| PortugalRua Egas Moniz 173S. João do Estoril2766-651 Estoril | Black & DeckerFax 214667580 | Tel. | 214667500 | |
| SuomiKägelhamnen 3, 02150 Esbo | Black & Decker OyKeilasatama 3, 02150 EspooFax (09) 2510 7100 | Puh.FaksiTel. | 010 400 430(09) 2510 7100010 400 430 | |
| SverigeFabriksg. 7, 412 50 Göteborg | Black & Decker ABFax 031-68 60 80 | Tel. | 031-68 60 60 | |
| United Kingdom210 Bath RoadSlough, Berkshire SL1 3YD | Black & DeckerFax 01753 551155Helpline 01753 574277 | Tel. | 01753 511234 | |
| Middle East & AfricaPB 5420, Dubai, United Arab Emirates | Black & Decker (Overseas) A.G.Fax +971 4 2826466 | Tel. | +971 4 2826464 | |
Dealer address Date of purchase
Händleradresse Kaufdatum
Forhandier adress: Indkabsdato
