Vapore Stiro 3000 - Iron Di4 - Free user manual and instructions

USER MANUAL Vapore Stiro 3000 Di4

WE WOULD LIKE TO THANKS YOUR FOR CHOOSING DI4, WE WISH THE PRODUCT PERFORMS TO YOUR SATISFACTION AND PLEASURE.

WARNING

PLEASE READ THE INSTRUCTIONS FOR USE CAREFULLY PRIOR TO USING THE PRODUCT. STORE THESE IN A SAFE PLACE FOR FUTURE REFERENCE.

DESCRIPTION

A-Spray button

B-Shot of steam button

C-Steam regulator

D- Cover for filling opening

E- Output water spray

F-Self-cleaning button*

G-Temperature Control

H-Temperature indicator light

1-Level mark for maximum filling

J-Power cord

K-Soleplate

*Depends of the model you can find the special button Self-cleaning or you can find this function in the control of the steam.

SAFETY INSTRUCTIONS

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

If the supply cord is damaged it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

The iron must not be left unattended while it is connected to

the supply mains.

The plug must be removed from the socket-outlet before the water reservoir is filled with water.

The iron must be used and rested on a flat, stable surface

When placing the iron on its stand, ensure that the surface on which the stand is placed is stable.

The iron is not to be used if it has been dropped, if there are visible signs of damage or if it is leaking.

Keep the iron and its cord out of reach of children less than 8 years of age when it is energized or cooling down.

CAUTION Hot surfaces. Surfaces are liable to get hot during use.

IMPORTANTWARNINGS

This appliance is designed for home use and should never be used for commercial or industrial use under any circumstances. Any incorrect use or improper handling of the product shall render the warranty null and void.

Prior to plugging in the product, check that your mains voltage is the same as the one indicated on the product label.

If you use one adaptor make sure it can reach 16 A and is provided with earth socket

The mains connection cable must not be tangled or wrapped around the product during use.

Do not use the device, or connect and disconnect to t supply mains with the hands and / or feet wet.

Do not pull on the connection cord in order to unplug it or use it as a handle

Do not direct steam at people and animals.

Do not place the appliance under the tap to fill the water tank, or immerse it in water or other liquids. Unplug the product immediately from the mains in the event of any breakdown or damage and contact an official technical support service. In order to prevent any risk of danger, do not open the device. Only qualified technical personnel from the brand's Official technical support service may carry out repairs or procedures on the device. Only an official technical support service centre may carry out repairs on this product.

Proceed according to maintenance and cleaning section of this manual for cleaning

B&B TRENDS SL. disclaims all liability for damages that may occur to people, animals or objects, for the non-observation of these warnings.

BEFORE THE FIRST USE

Before using the steam iron, please ensure you read the user manual and understand all parts and features of the Steam Station. Be sure to remove any packaging material and labels before using for the first time.

In the first use they can break off odors or fumes that sent quickly. Do not spray for the first time on clothes and there may be traces of dirt on the soleplate

HOW TO USE

Always check whether a label with ironing instructions is attached to an article to be ironed. Follow these instructions in all cases.

Turn the temperature control dial round to set the appropriate temperature indicated in ironing instructions or in fabric label.

Marking Material, for example
·(1 dot) Acetate, elastane, polyamida, polypropylene
·(2 dots) Cupro, polyester, silk, triacetate, viscose, wool
·(3 dots) Cotton, linen

Insert the main plug into the wall socket. The indicator light will turn on.

When the indicator light goes out you may start ironing.

WATER TANK FILLING

Unplug the iron before filling the water tank.

Open the cover for filling.

Slowly pour water through the water inlet.

Do not fill higher than mark on the water tank, in order to avoid spilling out of water.

NOTE: Your steam iron is designed to use tap water, however, if the water is very hard, it is advisable to use distilled water.

The water tank should be emptied after each use.

SPRAYING

As long as there is enough water in the water tank, you may use the spray button at any temperature setting during steam or dry ironing.

Press the spray button several times to activate the pump while you are ironing.

STEAM IRONING

Set the temperature control dial to the desired position in accordance with the manufacturer's label.

Set the variable steam control to the desired position.

CAUTION: Avoid coming in contact with ejected steam.

DRY IRONING

The steam iron can be used on the dry setting with or without water in the water tank, it is best to avoid having the water tank full while dry ironing.

Turn the variable steam control to the minimum position.

Select the setting on the temperature control dial best suited for the fabric to be ironed.

CAUTION: If the steam iron has been used for a long time, it is hot and there is no water. Do not refill it with water until the steam iron cools down.

SHOT OF STEAM

The shot of steam feature provides additional steam for removing stubborn wrinkles.

Turn off the variable steam control to the min position

Press the powerful steam button to release the burst of steam.

NOTE: To prevent water leakage from the soleplate, do not keep the powerful steam button in continuously and wait almost 5 seconds between pressures.

VERTICAL IRONING

By pressing the shot-steam button at intervals you can also iron vertically (curtains, hung garments, etc.)

NOTE: To prevent water leakage from the soleplate, do not keep the powerful steam button in continuously and wait almost 5 seconds between pressures.

WHEN YOU FINISHED IRONING

Set the temperature dial to the minimum position.

Remove the main plug from the wall socket.

Stand the iron on heel rest.

MANITENCE AND CLEANING

It is recommended to the self-cleaning every two weeks if the water in the area is hard or semi-hard if frequent use of the device is made

Before cleaning the steam iron ensure it is unplugged from the power supply and has completely cooled down.

Do not use abrasive cleaners.

To clean exterior surfaces, use a damp soft cloth and wipe dry. Do not use any chemical solvents, as these will damage the surface.

Cleaning the soleplate; do not use scouring pads or harsh cleaners on the soleplate as these will damage the surface. To remove burnt residue, iron over a damp cloth while iron is still hot. To clean the soleplate, simply wipe with soft damp cloth and wipe dry.

SELF-CLEANING

Fill the half of the water reservoir.

Set the temperature control to its maximum position.

Insert the main plug into the wall socket.

Allow the iron to heat up until the indicator light goes out.

Unplug the steam iron.

Holding the iron horizontally over the sink and press the button of self-clean, in case if not have this button change the steam control to the maximum position.

Boiling water and steam will be ejected from the holes in soleplate with impurities washed out Move the iron over an old (preferably) piece of cloth. This ensures that the soleplate will be dry during storage.

ANTI-CALC SYSTEM

A special resin filter inside the water reservoir softens the water and prevents scale build-up in the plate. The resin filter is permanent and does not need replacing.

Please note: Use tap water only. Distilled and/mineralized water makes the "Zero-Calc", anti-calc system ineffective by altering its physicochemical characteristics.

Do not use chemical additives, scented substances or decalcifies. Failure to comply with the above-mentioned regulations leads to the loss of guarantee.

ANTI-DRIP SYSTEM

With the anti-drip system, you can perfectly iron even the most delicate fabrics.

Always iron these fabrics at low temperatures. The plate may cool down to the point where no more steam comes out, but rather drops of boiling water that can leave marks or stains. In these cases, the Anti-drip system automatically activates to prevent vaporization, so that you can iron the most delicate fabrics without risk of spoiling or staining them.

AUTO SHUT-OFF

An electronic safety device will automatically switch the heating element off if the iron has not been moved more than 30 seconds in a horizontal position. If in a vertical position, this will happen after 8 minutes. To indicate that the heating element has been switched off, the auto-off pilot light will start blinking.

When picking up the iron again, the auto-off pilot light will turn off. The power pilot light will turn on. This indicates that the iron is heating up again.

Wait for the power pilot light to turn off. Then the iron is ready for use.

TROUBLESHOOTING

PROBLEM POSSIBLE	CAUSE Solution
SOLEPLATE IS NOT HEATING EVEN THOUGH IRON IS TURNED ON.	Connection problem Check main power	supply cable, plug and outlet.
	Temperature control is in MIN position	Select adequate temperature
IRON DOES NOT PRODUCE STEAM	Not enough water in tank Fill water tank
	Steam control is selected in non-steam position.	Set steam control between positions of minimum steam and maximum steam (see“iron chart”).
	Selected temperature is lower than that specified to use with steam.	Select a higher temperature
SPRAY FUNCTION DOES NOT WORK	Not enough water in tank Fill water tank	(see “getting started”, no 2).
STEAM JET AND VERTICAL STEAM JET FUNCTION DOES NOT WORK	Steam jet function was used very frequently within a short period.	Put iron on horizontal position and wait before using steam jet function.
	Iron is not hot enough Adjust to higher temperature to steam ironing. Put iron in vertical position and wait temperature indicator light turns off.
THE IRON LEAKING	The temperature setting is too low to produce steam.	The variable steam knob must be set on“0”position until the iron is hot.

PRODUCT DISPOSAL

This product complies with European Directive 2012/19/EU on electrical and electronic devices, known as WEEE (Waste Electrical and Electronic Equipment), provides the legal framework applicable in the European Union for the disposal and reuse of waste electronic and electrical devices. Do not dispose of this product in the bin, instead going to the electrical and electronic waste collection centre closest to your home.

We hope that you will be satisfied with this product.

FRANÇAIS

MERCI D'AVoir PLACÉ LEUR CONFIANCE EN DI4 ET NOUS ESPÉRONS QUE CE PRODUIT VOUS DONNERA ENTière SATISFACTION ET PLAISIR.

ATTENTION

VEUILLEZ LIRE ATTENTIVEMENT LE MANUEL D'UTILISATION AVANT D'UTILISER LE PRODUIT. CONSERVEZ CE MANUEL D'UTILISATION DANS UN ENDROIT SÜR EN VUE DE CONSULTATION FUTURE.

DESCRIPTION

ÉLIMINATION DU PRODUIT

B&B TRENDS, SL. guarantees compliance of this product for the purpose for which it is intended for a period of two years for the entire Spanish territory. In the case of breakdown during the term of this warranty, you are entitled to repair or to the replacement of the product at no charge if the former is unavailable, unless one of these options prove impossible or disproportionate. In this case, you can then choose a reduction in price or cancellation of the sale, which must be dealt with directly with the sales vendor. This also covers replacement of spare parts provided that the product has been used according to the recommendations specified in this manual for both cases, and has not been tampered with by any third party that is unaccredited by B&B TRENDS, SL. This warranty does not affect your rights as a consumer in accordance with the provisions of Law 23/2003 dated 10 July 2003 on warranties on the sale of consumer goods in the Spanish territory.

USE OF WARRANTY

Consumers should contact a technical service centre authorised by B&B TRENS, SL. for repair of the product as any tampering thereof by persons not authorised by B&B TRENS, SL., as well as misuse or inappropriate use, will lead to the cancellation of this warranty. The warranty must be fully completed and delivered along with the receipt or delivery docket for the effective exercise of rights under this warranty.

Claims must take place within three years from delivery of the product according to the provisions of the warranty, and the consumer must inform the sales vendor of the lack of conformity, provided that such claim is made within the statutory period of warranty. This warranty should be retained by the user as well as the invoice, receipt or the delivery docket to facilitate the exercise of these rights. For technical service and after-sales care outside the Spanish territory, please submit your query to the point of sale where you purchased the item or by contacting B&B TRENS, SL.

BOLETIM DE GARANTIA

SUM. ELECT. DALMAU, S.C.P.

VILADOMAT,108

934539276

[e-mail]

08240 MANRESA

SERVICIO ELDE-JORGE MANERO

BRUCH,55

938728542

[e-mail]

08027 BARCELONA

SELAROM

PASSEIG MARAGALL, 102

933521805

[e-mail]

08020 BARCELONA

SAT MARINE, S.C.P.

C/HUELVA,67-69

932664697

[e-mail]

08620 SANT VICENQ DELS HORTS

SATJARO -

C/MALAGA,20-22

647054779

[e-mail]

08950 ESPLUGUES DE LLOBREGAT

SAT J. BAUTISTA

SUREDAI ASSOCIATS, S.C.

FRANCESCARTAU,2

972236588

[e-mail]

17200 PALAFRUGELL

NEW MERESA

DE LA SURERA BERTRAN, 23

972304454

[e-mail]

17300 BLANES

FRANCISCO PORTILLO PEIRO

ASIAS MARC 1

972331249

[e-mail]

17740 VILAFANT

ELECTRONICA VILAFANT-SAT

NAVATA, 13

972506515/615090154

[e-mail]

GRANADA

18015 GRANADA

LUNSOL, S.L.

SANTIAGO APOSTOL 18 Local

959283415/627349431

URBISAT (BALEAR SERVICE)

C/MATEU OBRADOR,8

971-733886/733879

[e-mail]

7740 MENORCA

ES MERCADAL

SERVEIS MENORCA, S.L.

CARRER NOU N°53

971375380

[e-mail]

JAÉN

23400UBEDA

MAGOCAUBEDA

GRANADA 7

953751838

[e-mail]

23001JAEN

corbega@ hotmail.com

LUGO

27002 LUGO

TELESERVICIO (JOSE ANTONIO)

CARRIL DE LAS FLORES, 34-B

982242015

[e-mail]

27400 MONFORTE DE LEMOS

RAULE HJOS.S.L.

CAMPO DE LA COMPANIA, 19

982400711

[e-mail]

27850 VIVERO (CASCO

SERVICIO TECNICO SILDO 101, S.L.U.

LODEIRO,26

982061819

MADRID

28931MOSTOLES

Valle Inclan 32 Local

917054624

[e-mail]

28047 CARABANCHEL

REPARACIONES CARLOS (CARLOS

GOMEZ YUSTE)

GUABAIRO,2

914665369

[e-mail]

VALENCIA

46600 ALZIRA

TALLERES MOYA

C/FAVARETA,49

962418587

[e-mail]

46011 VALENCIA

ROBERTO BARRACHINA ALIAGA

-VALENCIANA, SA TECNICA

C/FRANCISCO BALDOMA,86 Bajos

963554244/607304279

[e-mail]

46700 GANDIA

RELGAN-CAMILO GARCIA

MAGISTRADO CATALA, 16

962872810

[e-mail]

46005 VALENCIA

RELEVAN,S.L.

C/MATIASPERELLO,49

963222529

[e-mail]

46800 XATIVA

JOSE PASTOR DIEZ

C/ABUMASAIFA.6

962274794

[e-mail]

46680 ALGEMESI

JOSE A. LLACER SANGROS

ALBALAT,88

962423519

satllacer@ hotmail.com

46700 GANDIA

JOAOQUIN MAYOR ESTRUGO

(TECNOGAR)

PRIMER DE MAIG 41-B

962865335

[e-mail]

46470 CATARROJA