Jet Pressing Healthy Compact - Iron Di4 - Free user manual and instructions

USER MANUAL Jet Pressing Healthy Compact Di4

WE WOULD LIKE TO THANK YOU FOR CHOOSING DI4. WE WISH THE PRODUCT PERFORMS TO YOUR SATISFACTION AND PLEASURE.

WARNING

Please read the instructions for use carefully prior to using the product. store these in a safe place for future reference.

DESCRIPTION

1. "Calc'nClean" descaling button with indicator light
2. "on / off" button with indicator light
3. Energy saving "ECO" and "BOOST" button with indicator light / "HEALTHY/BOOST" button *
4. Supply hose
5. Mains cable
6. Supply hose and mains cable storage fixing
7. Water tank
8. Level mark for maximum filling
9. Filling opening
10. Iron lock
11. Soleplate
12. Steam release button
13. "Calc'nClean" container

* available depending on model

GENERAL SAFETY INSTRUCTIONS

The appliance must not be left unattended while it is connected to the supply mains.

Remove the plug from the socket before filling the appliance with water or before pouring out the remaining water after use.

The appliance must be used and placed on a flat, stable surface.

When placing the iron on its stand or on its heel, make sure that the surface on which the stand or heel is placed is stable.

The appliance should not be used if it has been dropped, if there are visible signs of damage or if it is leaking water. It must be checked by an authorised Technical Service Centre before it can be used again.

EN

With the aim of avoiding dangerous situations, any work or repair that the appliance may need, e.g. replacing a faulty mains cable, must only be carried out by qualified personnel from an Authorised Technical Service Centre.

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

Keep the appliance and its cord out of reach of children under 8 years of age when it is turned on or cooling down.

This appliance is designed only for household use up to 2000m above sea level.

CAUTION. Hot surface. Surface is liable to get hot during use.

IMPORTANT WARNINGS

Carefully read through the operating instructions for the appliance and safeguard them for future reference.

This appliance has been designed exclusively for normal household use in home environment.

This appliance must be used only for the purposes for which it was designed, i.e. as an iron. Any other use will be considered improper and consequently dangerous. The manufacturer will not be held responsible for any damage arising from misuse or improper use.

This appliance is to be connected and used in accordance with the information stated on its characteristics plate.

This appliance must be connected to an earthed socket. If it is absolutely necessary to use an extension cable, make sure that it is suitable for 16A and has a socket with an earth connection.

The appliance must never be placed directly under the tap to fill the water tank.

The electrical plug must not be removed from the socket by pulling the cable.

Never immerse the appliance in water or any other liquid.

Do not leave the appliance exposed to weather conditions (rain, sun, frost, etc.)

This appliance reaches high temperatures and produces steam during use, this could cause scalds or burns if not used properly.

Do not allow the power cable to come into contact with the soleplate when it is hot.

B&B TRENDS S.L. disclaims all liability for damages that may occur to people, animals or objects, for the non-observance of these warnings.

USING YOUR APPLIANCE

Filling the water tank

This appliance has been designed to use normal tap water.

IMPORTANT: Do not additive! Do not use additives! The addition of other liquids, such as perfume, vinegar, starch, condensation from tumble dryers or air conditioning systems, or chemicals will damage the appliance. Any damage caused by the use of the aforementioned products will he guarantee void!

Fill the water tank (7). Never fill beyond the level "max" (8)

Tip: To prolong the optimum steam function, you may mix tap water with distilled or demineralised water 1:1. If the tap water in your area is very hard, mix tap water with distilled or demineralised water 1:2.

Heating

1. Unwind the supply hose (4) and the mains cable (5). Plug mains cable into an earthed socket.
2. Press the button (2) to switch the appliance on. The indicator light (2) will flash indicating that the appliance is heating up.
3. When the iron is ready to use, the indicator light (2) will remain permanently lit. Two beeps will be heard.

Ironing

1. Press the steam release button (12) for ironing with steam.

IMPORTANT:

During first use: Press the steam release button for 40 seconds until steam comes out.

During the first seconds of use the amount of steam will be lower and it will increase progressively. Drops of water may leak out while there is still air in the circuit.

WARNING: Ironing with an excessive amount of steam may produce condensation of the hot water and dripping from the ironing board or through any other permeable surface.

"Steam Turbo Shot" function

This appliance has a special function for tackling difficult creases.

1. Press the steam release button (12) two times in quick succession (double-click). Powerful shots of steam will be released.

Vertical steam

Can be used to remove creases from hanging clothes, curtains, etc.

1. Hold the iron in an upright position 15 cm away from the garment to be steamed.

2. Press the steam release button (13) repeatedly with pauses of at least 5 seconds.

WARNING: Never point the steam jet at garments being worn, or at people or animals.

Energy saving (available depending on model)

If the energy saving setting is selected, you can save energy and water and still achieve good results when ironing most of your garments.

1. Press the energy saving button "ECO/BOOST" (3). The indicator light will come on.
2. To switch back to the normal energy setting, press the "ECO/BOOST" button again. It is advisable to use the normal energy setting to get optimum results on thick and very wrinkled fabrics.

EN

Tips to help you save energy:

If you tumble dry your fabrics before ironing them, set the tumble drier on the iron dry programme.

Try to iron the fabrics while they are still damp and reduce the steam setting. Steam will be generated from the fabrics rather than the iron.

The most efficient way to iron with steam generators is to use the steam function in a forward direction (the steam permeates the fabric and gives volume back to it) and in a backwards direction without steam (fixing the fabric).

Healthy Program (available depending on model)

If the “Healthy” program is activated, it provides a special combination of temperature and steam application intervals to obtain a hygienic effect without using chemical additives. It can be used on all types of fabrics and is extremely efficient on both thick and delicate fabrics.

1. Press the "HEALTHY / BOOST" button (3). The indicator lamp will illuminate.
2. To return to normal mode, press the "HEALTHY / BOOST" button again. Normal mode is recommended for best results on thick and heavily wrinkled garments.

Tips for efficient use:

• Place the iron on the garment or fabric you want to disinfect, or vertically in front of the garment keeping a certain distance.
• Press the steam release button continuously. Powerful blows of hygienic steam will be emitted. Slowly slide the iron over the garment or up and down vertically for best results.

Maximum power mode

For garments that need more powerful steam, you can activate the “Boost” mode to obtain the maximum steam quantity.

1. Press and hold down the button "ECO/BOOST" (3) during 5 seconds. The indicator light will flash.
2. To switch back to the normal energy setting, press the "ECO/BOOST" button again.

Auto switch off

For your safety and to save energy, the appliance switches off automatically when it has not been used for 8 minutes.

Three beeps will be heard, and all indicator lights (1, 2, 3) will flash.

1. To switch the steam station back on, press the steam release button (12) again.

CLEANING & MAINTENANCE

1. Descaling process

This appliance is equipped with an automatic clean warning indicator, which indicates that scale particles must be removed from inside the steam chamber.

When activated, three beeps will be heard and the "Calc'nClean" indicator light (1) will flash, indicating that the process should be performed.

You may continue ironing for a time. Once this time has passed, you will only be able to dry iron (without steam).

To start steam ironing again, follow this descaling process:

1. Fill the tank (7) with water.
2. Plug in the mains cable (5) and press the button (2) to switch the appliance on.
3. Press the descaling button (1) for 2 seconds. Its indicator light will remain permanently lit.
4. Wait until the indicator light (2) stops flashing and remains lit permanently. Two beeps will be heard.
5. Place the iron on the "Calc'nClean" container (13). Make sure that the surface on which the container is placed is stable.

WARNINGS:

Do not remove the iron from the container until the process has finished. Boiling water and steam will be released through the soleplate, removing limescale and/or deposits that may be inside.

The container must only be used to perform the descaling process. It must not be used as a stand for the iron while ironing.

1. Press the steam release button (12) for 2 seconds. The descaling process will start automatically. During this process, short beeps will be heard.
2. After approximately 3 minutes, the iron will stop releasing steam. A long beep will be heard, indicating that descaling process has finished. The appliance will switch off automatically.
3. To clean the soleplate (11), immediately rub off any residue by running the hot iron over a wet cotton cloth. Wipe the housing of the iron with a cloth.

WARNING: The container gets hot during the descaling process.

1. Let it cool down and then empty the container.

2. Cleaning the appliance

Regularly clean your appliance for properly maintenance.

ATTENTION! Burn risk!

If the appliance is only slightly soiled, wipe it with a damp cotton cloth only, and then dry it.

To keep the soleplate smooth, you should avoid contact with hard metal objects. Never use a scouring pad, or chemicals to clean the soleplate.

3. Storing the appliance.

1. Unplug the appliance and let it cool down. Empty the water tank (7).
2. Place the iron on the steam station, standing on its heel, and lock the iron with the fixing lever (10).
3. Roll up the mains cable (5) and the supply hose (4) in the storage fixing (6). Do not wrap the cords too tight.

Troubleshooting

Problem Possible cause Solution
The iron begins to smoke when switched on	During first use: certain components on the appliance have been lightly greased at the factory and may produce a small amount of smoke when initially heated	This is completely normal and will stop after a short while
The iron does not produce any steam	During first use, water has not filled the hose (4) completely	Press and hold the steam release button (12) until steam comes out
	The “Calc’nClean” indicator light (1) will flash. The descaling process has not been completed	Perform a cleaning cycle (see the “Descaling process” section)
Dirt comes out through the soleplate	There is a build-up of lime scale or minerals in the iron	Carry out a cleaning cycle (see the “Descaling process” section)
	Chemical products or additives have been used	Never add products to the water (see the “Filling the water tank” section). Clean the soleplate with a damp cloth
The “Calc’nClean” indicator light (1) does not turn off	The iron descaling process has been stopped before being completed	Restart and complete the iron descaling process
The appliance makes a pumping sound	Water is being pumped into the iron	This is normal
	The water tank is empty Fill the water tank
There is too much steam coming out of the iron	Mode “Boost” is turned on	Activate the normal mode by pressing the “ECO/BOOST” button
The iron produces little steam	The iron has been switched on recently	It is normal, the iron produces steam gradually until it is stabilized

If the above tips do not solve the problem, get in touch with our customer service.

ADVISE ON DISPOSAL

Our goods come in optimized packaging. This basically consists in using non-contaminating materials which should be handed over to the local waste disposal service as secondary raw materials. Your local town council can give you information about how to dispose of obsolete appliances.

This product complies with European Directive 2012/19/EU on electrical and electronic devices, known as WEEE (Waste Electrical and Electronic Equipment), provides the legal framework applicable in the European Union for the disposal and reuse of waste electronic and electrical devices. Do not dispose of this product in the bin, instead going to the electrical and electronic waste collection centre closest to your home.

We hope that you will be satisfied with this product.

NOUS TENONS À VOUS REMERCIER D'AVOIR CHOISI DI4. NOUS ESPÉRONS QUE VOUS SEREZ PLEINEMENT SATISFAIT DE CE PRODUIT ET QU'IL RÉPONDRA À VOS ATTENTES.

ATTENTION

B&B TRENDS, SL. guarantees compliance of this product for the use for which it is intended for a period of three years. In the case of breakdown during the term of this warranty, users are entitled to repair or else the replacement of the product at no charge if the former is unavailable, unless one of these options proves impossible to fulfill or is disproportionate. In this case, you can then opt for a reduction in price or cancellation of the sale, which must be dealt with directly with the sales vendor. This also covers replacement of spare parts provided that the product has been used according to the recommendations specified in this manual for both cases, and has not been tampered with by any third party that is not authorised by B&B TRENDS, SL. The warranty will not cover any parts subject to wear and tear. This warranty does not affect your rights as a consumer in accordance with the provisions in Directive 1999/44/EC for member states of the European Union.

USE OF WARRANTY

Customers must contact a B&B TRENDS, SL., authorised Technical Service for repair of the product. Since any tampering of the same by anyone not authorised by B&B TRENDS, SL., or the careless or improper use of the same shall render this warranty null and void. The warranty must be fully completed and delivered along with the receipt or delivery docket for the effective exercise of rights under this warranty.

This warranty should be retained by the user as well as the invoice, receipt or the

delivery docket to facilitate the exercise of these rights. For technical service and after-sales care outside the Spanish territory, please submit your query to the point of sale where you purchased the item.

BOLETIM DE GARANTIA

ANTHONY ALLEN ASHMORE

RODRIGUEZ (ELECT.MON-TESINOS)

C/ORIHUÉLA, 43

966703505

[e-mail]

ALMERIA

04867 MACAEL

POL.INDR."DOMENYS I"

NAVE 9

938904852

[e-mail]

SUREDAI ASSOCIATS, S.C.

FRANCESCA ARTAU, 2

972236588

[e-mail]

17200 PALAFRUGELL

NEW MERESA

DE LA SURERA BERTRAN.

23

972304454

[e-mail]

17300 BLANES

FRANCISCO PORTILLO

PEIRO

ASIAS MARC 1

972331249

[e-mail]

17740 VILAFANT

ELECTRONICA VILAFANT

- SAT

NAVATA, 13

972506515 / 615090154

electronicavilafant@hotmail.

com

GRANADA

18015 GRANADA

LUNSOL, S.L.

AVDA. VIRGEN DE LA CON-

SO 4, LOCAL 2

958292565

[e-mail]

18007 GRANADA

ELECTRICIDAD MORENO

C/ PALENCIA, 3

95 881 05 35

morenotorres@carretero200.

com

GUADALAJARA

19004 GUADALAJARA

FERRETERIA AL-YE

AVDA, EJERCITO,11-D POS-

TERIÓR

949218662

[e-mail]

GUIPUZCOA

20014 SAN SEBASTIAN (no oficial)

SANTIAGO ESTALAYO

URBISAT (BALEAR SERVICE)

C/MATEU OBRADOR,8

971-733886/733879

[e-mail]

7740 MENORCA

ES MERCADAL

SERVEIS MENORCA, S.L.

CARRER NOU N° 53

971375380

[e-mail]

JAÉN

23400 UBEDA

MAGOCA UBEDA

GRANADA 7

953751838

[e-mail]

23001 JAEN

CARRIL DE LAS FLORES, 34-B

982242015

[e-mail]

27400 MONFORTE DE

LEMOS

RAUL E HIJOS.S.L.

CAMPO DE LA COMPAÑÍA, 19

982400711

[e-mail]

27850 VIVERO (CASCO

SERVICIO TECNICO SILDO

101, S.L.U.

LODEIRO, 26

982061819

MADRID

28931 MOSTOLES

REPARACIONES RAGON

S.L.

BURGOS 4-6

916147898

[e-mail]

28044 MADRID

REPARACIONES PIMAR

Valle Inclan 32 Local

917054624

[e-mail]

28047 CARABANCHEL

REPARACIONES CARLOS

(CARLOS GOMEZ YUSTE)

GUABAIRO.2

914665369

JESUS MANUEL MONSALVO

MENDO

ANGUSTIAS,42

983810205

[e-mail]

47002 VALLADOLID

ELECTRICIDAD RINCON, S.A.

LABRADORES, 9 Y 11

983297133

administracion@electricida-

drincon.es

VIZCAYA

48004 BILBAO

SERTEK

C/ PADRE PERNET, 8

944112282

[e-mail]

48013 BILBAO

REPARADOMESTICOS, JOSU

URKIXO ZUMARKALEA,79

944 90 41 66

[e-mail]

48011 BILBAO

R.E. ABAD MANUEL GON-

ZALEZ HERVERA

GREGORIO DE LA REVILLA, 34

944215271

[e-mail]

48980 SANTURCE

JULEN SAT

LAS VIÑAS 20-22

944617193

[e-mail]

ZAMORA

49010 ZAMORA

TERESA PEREZ

DIEGO DE LOSADA, 10

980671386

[e-mail]

ZARAGOZA

50001 ZARAGOZA