GS29NVWE0N - Freezer SIEMENS - Free user manual and instructions

Product type	Freezer
Brand	Siemens
Model	GS29NVWE0N
Installation type	Freestanding (not built-in)
Energy efficiency class	A++ (estimated)
Annual consumption	Approximately 250 kWh/year (estimated)
Noise level	42 dB(A) (estimated)
Dimensions (H x W x D)	185 x 60 x 65 cm (estimated)
Weight	Approximately 80 kg (estimated)
Power supply	220-240 V, 50 Hz
Interior lighting	Removable and replaceable LED
Ice maker	Integrated, removable and replaceable
Frozen food drawer	Removable and replaceable
Door gasket	Removable and replaceable (requires a hair dryer for optimal adjustment)
Door handle	Replaceable (standard or easy-open)
Hinges	Upper and lower replaceable (Torx TX20)
Shelves	Tool-free removable
Repairability	Spare parts available: gasket, handle, hinges, lighting, drawer, ice maker. Repairs possible by the consumer with appropriate tools.
Safety	Unplug the appliance 60 seconds before any repair. Wear protective gloves. Use only original parts.
Required tools	Torx TX20 bit, flathead screwdriver (2.4 mm and 10 mm), Phillips screwdriver PH2, protective cloth

Frequently Asked Questions - GS29NVWE0N SIEMENS

How to replace the door gasket?

Remove the old gasket by pulling it out of the groove at the corners. To install the new gasket, gently warm it with a hair dryer or hot water to reshape it, then push the corners into the groove and gradually press it in all the way.

How to remove the door handle?

First remove the two screw caps, then unscrew the two screws with a Torx TX20 bit. The handle can then be removed. Reassembly is in reverse order.

Can I replace the LED lighting myself?

Yes, after unplugging the appliance and removing the upper interior fittings. Use a flathead screwdriver (2.4 mm blade) to slide the lighting to the left, disconnect the electrical connection, release the hooks, and remove it from the front. Installation is the reverse.

What tools are needed for common repairs?

Recommended tools include a Torx TX20 bit (6.3 mm), a flathead screwdriver (2.4 mm and 10 mm blades), a Phillips screwdriver PH2, and a protective cloth. Some repairs also require a hair dryer.

What safety precautions should I take before a repair?

Unplug the appliance from the mains at least 60 seconds before starting. Wear protective gloves against sharp edges. For heavy appliances, secure them against falling and get help if needed. Use only original spare parts.

How to remove the frozen food drawer?

Open the door and fully pull out the drawer outward. Lift it to remove. Installation is simple: insert it and push until it stops.

How to replace the ice maker?

First, pull out the drawer containing the ice bucket and ice maker. Unhook the hooks of the ice maker, then remove it. Install the new one by reversing the steps.

Is the easy-open handle replaceable?

Yes. Remove the cover and unscrew the two screws with a Phillips screwdriver PH2. Before reassembly, ensure the mechanism (rod, toothed quadrants, spring, and stop) is correctly adjusted according to the diagram in the manual.

Where can I find spare parts for this freezer?

Contact Siemens after-sales service or an authorized dealer. Use the references provided in the manual (e.g., [00340865] for the Torx TX20 bit, [00342013] for the protective cloth). Use only original parts.

What should I do if the door does not close properly?

First check if the door gasket is deformed. You can warm it with a hair dryer and reposition it. If the problem persists, check the hinges: they can be adjusted or replaced (see sections 4.4 to 4.6 of the manual).

USER MANUAL GS29NVWE0N SIEMENS

4.3 Replacing the easy opening handle 11

4.3.1 Removing the easy opening handle 11 4.3.2 Installing the easy opening handle 11

4.4 Replacing the door panel and the door 12

4.4.1 Removing the door panel 12 4.4.2 Installing the door panel 14

4.5 Replacing the top door panel (door with display) 15

4.5.1 Removing the door panel 16 4.5.2 Installing the door panel 17

4.6 Replacing the bottom door panel 18

4.6.1 Removing the bottom door panel 18 4.6.2 Installing the bottom door panel 19

4.7 Replacing the handle 20

4.7.1 Removing the handle 20 4.7.2 Installing the handle 20

4.8 Replacing the container for contaminated food products 21

4.8.1 Removing the container for contaminated food products 21 4.8.2 Installing the container for contaminated food products 21

4.9 Replacing the defroster 22

4.9.1 Removing the defroster 22 4.9.2 Installing the defroster 22

4.10 Replacing the LED lighting 23

4.10.1 Connecting the LED lighting 23 4.10.2 Mounting the LED lighting, second part 24

ABOUT THIS DOCUMENT

1.1 Important information

1.1.1 Purpose

This guide is intended to help the installer to install the device in accordance with the regulations for environmentally friendly design of devices (from 03.2021).

It contains information on how to replace certain spare parts, including warnings and risks.

If you have any questions, please contact our customer service department. We are not responsible for damages if the repair instructions have not been followed correctly.

1.2 Explanation of symbols

1.2.1 Danger symbol

The warning symbol is a triangle with an exclamation mark. The exclamation mark indicates the severity of the danger.

Ниво на п dedурждени 3начени
ОПАСHОCT	Еспаразы新股у на п dedурждени.TО сбоб Shedени по Смьт ини сернони наразяваим.
ПРEDУПЕЖДЕНЕ	Еспаразы新股у на п dedурждени.TOTСбоб Shedени по Смьт ини сернони наразяваим.
ВИМATEЛНО	Еспаразы新股у на п dedурждени.TOTСбob Shedени по Смьт ини наразяваим.
ВИМАМЕЛ	Еспаразы新股у на п dedурждени.TOTСбob Shedени по Смьт ини смьз. БЕТВЕНI.YE.TN.

Table 1: Danger symbol

1.2.2 Danger symbols

Danger symbols are symbolic images that provide information about the type of danger.

The following danger symbols are used in this document:

Electrical danger

Immediately inform about danger/prevention

Measures taken to prevent danger.

A specific example shows a warning that warns of electric shock, which can occur on parts under voltage. The warning label for danger is placed.

DANGER

Risk of electric shock from parts under voltage!

Electric shock

Disconnect the electrical equipment from the power supply before opening or servicing.

1.2.4 General symbols

The following general symbols are used in this document:

Оьш симвов Зачени
I	Иденихицаре на спесиален сьвет (TEKCT w/ллграфика)
I	Иденихицаре на постс сьвет (само TEKCT)
I	Иденихицаре на врьзka Кьм Вideо урок
I	Иденихицаре на необхочимite И-стру金融市场
I	Иденихицаре на необхочимite поедырпелейн усповия
I	Иденихицаре на усю病变 (ako ..., Тогава ... )
I	Иденихицаре на рezупат
[Стар]	Иденихицаре на Клиочни睁�能он
[00123456]	Иденихицаре на Каталожен Homep
[Статус]	Иденихицаре на по��аизая СЕСТ/празорец (на диспега на урEDA)

Table 3: General symbols

Safety

2.1 General safety instructions

2.1.1 For all household appliances

Risk of electric shock from parts under voltage!

• During repairs, including electrical components, there is a risk of electric shock!
• Check the electrical connection for about 60 seconds before starting work. Before installation, safety must be checked according to VDE 0701 or in accordance with the country-specific regulations.

Risk of injury from sharp edges!

Wear protective gloves.

Risk of injury during repair, maintenance, and disassembly of the device. Moving components.

Wear protective shoes. Secure the components so they do not fall. Do not allow contact of body parts with moving components.

Safety risk for people and equipment! - Use only original spare parts. Risk of damage to electrostatic sensitive components (ESD) from improper handling, including cables and connectors.

Tools and aids

Installation of the device.

Repair

4.3 Removing the easy opening handle

Special tools:

Cross-head screwdriver PH2

Removal:

The device is disconnected from the power supply. The door is open.

4.3.1 Removing the easy opening handle

1. Cibanete kanaeTo Ha easy opening handle (1).
2. Pa3BnIe DaBaTa BnHTa (2).

Easy opening handle e cbaneHa.

4.3.2 MoNTIpaHHe Ha easy opening handle

Mexaan3mbt Ha easy opening handle Tpa6ba Da 6bde npabnHn Hactpoen npenMOHTaKa. PpabnHTo paaonooKeHHe ha 6ytaHnna Ppbt (1), HaaBSeHnTe KaanpaTn (2) (3), npyKnHata (4) n orpaHnHnten (5) 3a MoHTax Ha BpTaTaTAt OtnBa e noKa3aHO Ha padkNata.

MoHTnpaTBeB6paTeHpei.

PemOH

4.4 CmHa Ha rohpHaTa nHa Ta HbpaTaTa

CneuaJIHHHnCTpymeHTN:

HakpaimHK Torx TX20 6,3 MM (1/4") [00340865]

IPEADYNPEXKDEHNE

Teekn, o6emncTuypeu!

IobpeHa HpyrHuactn Ha ypeHa NmB Doma Ha KHeHTa, HAp. DbHO

TC

3akpenete KOMnoHeHTa, Taka Ye Da Ha naHe.

N3nCKBaHe:

YpeBt en3KIOueHOT 3axpaHbHeTo. BbtpseHHTEΦHTHnHa ypeDa ca oTcTaHeHN.

4.4.1 CbAaHHe H aHaTata Ha BpaTaTa

PemOH

1. NocTabete ypea Jernan Ha 3aHaTa cn Ctpana.

2.1.HatncheTe kanaeTo Ha rohpHaTa naHTa ot DBeTe cTpaHn (1).

1. N3BaJeTe KanaeTo Ha roPHaTa naHTa (2).
2. CbaneTe kanaeTo Ha rohpHaTa naHTa (3).

PemOH

3.1.PaBmTeDbTaBNHTa(1).

1. Cbane teropnata naHTa (2).

Tophata naHTa Ha BpaTata e CBaneHa. 4.4.2 MoHTnpaHe Ha naHTaTa Ha BpaTaTa

MoHTnpaIteB06paTeH peI.

PpnnnB3BaHe Ha HkNoHEn ypeN!

KocTHnΦpakTypn/HapaHbAHHoT npema3BaHe

Keep the device away from children.

CAUTION

Risk of falling parts during loosening of screws!

Hold the right parts of the device firmly to prevent it from falling.

WARNING

Risk of falling parts during loosening of screws!

Damaged parts on the device may cause injury to the client.

TO.

Secure the component so that it does not fall.

DANGER

Risk of electric shock from live parts under voltage!

DANGER for life from electric shock in case of incorrect repair.

Electrical appliances must be repaired only by qualified electricians. After repair, a safety check must be carried out in accordance with VDE0701 and in accordance with the country-specific regulations.

DANGER

Risk of electric shock from live parts under voltage!

Disconnect the device from the electrical supply and wait 60 seconds before starting repairs.

Inspection:

Remove the device from the electrical supply. Replace the filter if necessary.

Repair

4.5.1 Replacing the door hinge

1. Place the device on the side opposite the hinge.

Mount the hinge.

Repair

4.6 Replacing the door hinge

Special tools:

Torx wrench TX20 6.3 mm (1/4") [00340865]

WARNING

Danger, electric shock!

Mount the hinge.

4.8 Removing the container for contaminated food products

Pull: The door is open.

4.8.1 Removing the container for contaminated food products

1. Grab the cover of the container for contaminated food products (1). 2. Pull out the container for contaminated food products (2)

The container for contaminated food products is removed.

4.8.2 Installing the container for contaminated food products

Install the container.

The generator is removed.

4.9.2 Installing the generator

Install the generator.

4.10 Removing the LED lighting

Special tools:

Flat screwdriver, 2.4 mm x 0.4 mm x 60 mm, in the kit [00341820]

The LED lighting is built-in and cannot be removed. The lighting can only be repaired by a specialist from the customer service or by the manufacturer.

DANGER

Risk of electric shock from damaged parts! Disconnect the power supply before touching the damaged parts.

Electrical equipment must only be repaired by qualified electricians. After repair, a safety check must be carried out in accordance with VDE 0701 or in accordance with the national regulations.

DANGER

Risk of electric shock from damaged parts!

Electric shock

Disconnect the device from the power supply before opening it for repair.

CAUTION

Sharp edges!

Risk of injury

Wear protective gloves.

Removal:

The device is disconnected from the power supply. The cover is removed and the internal components are accessible.

4.10.1 Replacing the LED lighting

1. Replace the LED lighting.

Disconnect the appliance from the electrical supply before replacing the LED lighting.

2. Release the LED lighting clip.

Repair

3. Pull the LED lighting, holding it by the clip.

The LED lighting is released. 4.10.2 Mounting the LED lighting from the mounting bracket.

4.3 Replacing the easy opening handle 34

4.3.1 Removing the easy opening handle 34 4.3.2 Installing the easy opening handle 34

4.4 Replacing the upper door hinge 35

4.4.1 Removing the door hinge 35 4.4.2 Installing the door hinge 37

4.3 Replacing the Easy opening handle 56

4.3.1 Removing the Easy opening handle 56 4.3.2 Installing the Easy opening handle 56

4.4 Replacing the upper door hinge 57

4.3 Replacing the Easy opening handle

Special tools:

Make sure to secure the devices against slipping.

Danger of falling parts due to loose screws!

Risk of injury from falling parts. Make sure to secure the component against falling.

NOTE!

Danger of falling parts due to loose screws!

Make sure to secure the component against falling.

Presetting:

Make sure to secure the devices against slipping.

Danger of falling parts due to loose screws!

Risk of injury from falling parts. Make sure to secure the component against falling.

NOTE!

Danger of falling parts due to loose screws!

Make sure to secure the component against falling.

DANGER

Make sure to secure the appliance against slipping.

CAUTION

Danger of falling parts due to loose screws!

Risk of injury from falling parts. Make sure to secure the component against falling.

NOTE!

Danger of falling parts due to loose screws!

Make sure to secure the component against falling.

Presetting:

Repair hints - Freezer

1 Concerning this document. 116

1.1 Important information 116

1.1.1 Purpose 116 1.2 Explanation of symbols 116 1.2.1 Danger levels.. 116 1.2.2 Hazard symbols 116 1.2.3 Structure of the warnings 117 1.2.4 General symbols 117

Safety. 118

2.1 General Safety instructions 118

2.1.1 All domestic appliances 118

Tools and aids. 119

Repair 120

4.3 Replacing easy opening handle 124

4.3.1 Removing easy opening handle 124 4.3.2 Installing easy opening handle 124

4.4 Replacing door upper hinge 125

4.5 Replacing door upper hinge (door with display) 128

4.7 Replacing shelf. 133

4.7.1 Removing shelf 133 4.7.2 Installing shelf 133

4.8 Replacing frozen food container 134

4.8.1 Removing frozen food container 134 4.8.2 Installing frozen food container 134

4.9 Replacing ice maker 135

4.9.1 Removing ice maker 135 4.9.2 Installing ice maker 135

4.10 Replacing LED top light 136

4.10.1 Removing LED light. 136 4.10.2 Installing top LED light 137

Concerning this document

1.1 Important information

1.1.1 Purpose

These repair hints support consumers in repairing appliances themselves, in accordance with the applicable eco-design regulation (as of 03/2021).

They contain information on how to exchange defined spare parts, including warnings and risks.

In case of questions, please contact our customer service. We will only be liable for damages if the repair hints have been followed properly.

1.2 Explanation of symbols

1.2.1 Danger levels

The warning levels consist of a symbol and a signal word. The signal word indicates the severity of the danger.

Table 1: Danger levels

Warning level Meaning
Danger	Non-observation of the warning message will result in death or serious injuries.
Warning	Non-observation of the warning message could result in death or serious injuries.
Caution	Non-observation of the warning message could result in minor injuries.
Notice	Non-observation of the warning message could result in damage to property.

1.2.2 Hazard symbols

Hazard symbols are symbolic representations that give an indication of the kind of danger.

The following hazard symbols are used in this document:

Hazard symbol Meaning
!	General warning message
	Danger from electrical voltage
	Risk of explosion
	Danger of cuts
	Danger of crushing

Concerning this document

Hazard symbol Meaning
	Danger from hot surfaces
	Danger from strong magnetic field
	Danger from non-ionizing radiation

Table 2: Hazard symbols

1.2.3 Structure of the warnings

Warnings in this document have a standardized appearance and a standardized structure.

Danger

Type and source of danger!

Possible consequences of ignoring the danger / warning.

Measures and prohibitions for preventing the danger.

The following example shows a warning that warns against electric shock due to live parts. The measure for avoiding the danger is mentioned.

Danger

Risk of electric shock due to live parts!

Death by electrocution

• Disconnect appliances from electrical supply at least 60 seconds before starting repairs.

1.2.4 General symbols

The following general symbols are used in this document:

Gen. symbol Meaning
1	Identification of a special tip (text and/or graphic)
i	Identification of a simple tip (only text)
	Identification of a link to a video tutorial

Table 3: General symbols

Gen. symbol Meaning
	Identification of required tools
	Identification of required preconditions
	Identification of a condition (if ..., then ...)
	Identification of a result
[Start] Identification of a key or button
[00123456] Identification of a material number
Status Identification of displayed text / window (in the appliance's display)

Safety

2.1 General Safety instructions

2.1.1 All domestic appliances

Risk of electric shock due to live parts!

Errors by repairs involving electrical components can lead to electrical shock! - Disconnect the appliance from the mains for at least 60 seconds before starting work. After the repair have a safety test according VDE 0701 or country-specific regulations performed.

Risk of injury from sharp edges!

Wear protective gloves.

Risk of crushing during repair, maintenance, troubleshooting and service due to heavy and moving components

Wear protective shoes. - Secure heavy components from falling down. - Do not stick body parts into moving components.

Risk to the appliance's safety / function! Only use original spare parts. Risk of damage to electrostatically sensitive components (ESDs)! - Do not touch the modules, including connections and conductor paths.

Tools and aids

Designation Details Images
Protection cloth [00342013]	60 cm x 50 cm	###
Phillips screwdriver PH2
Torr Bit TX20 [00340865]	6.3 mm (1/4")
Slotted screwdriver	Blade 2.4 mm x 0.4 mm x 60 mm, in the kit [00341820]	①

Prerequisite: Door is open.

1. Release door gasket from the groove on right and left corner.

1. Pull out door gasket from groove.

Door gasket is removed.

	Thickness of new door gasket may deviate slightly from thickness of old door gasket. This will not affect closing behavior and long-term function.
	If your appliance has adjustable hinges or hinge attachments, you can optimize the closing behavior subsequently.
	Small side holes in door gasket are functional (required for ventilation). These are not production faults.

Repair

1. Check groove for gasket for damage.

1. If the groove for the gasket is damaged,
2. contact customer service.
3. Slight deformation of the door gasket is normal and does not affect its function. It is recommended to straighten the door gasket before inserting it into the appliance.

Heat the door gasket with a hair dryer or hot water and manually reshape it.

1. Push the corners of the gasket at the top and bottom into the groove.

Repair

1. Press the whole gasket step by step into the groove.

Door gasket is installed.

Slotted screwdriver Blade 10 mm x 1.6 mm x 200 mm

Prerequisite:

Appliance is disconnected from power supply. Door is open.

4.2.1 Removing door handle

1. Remove two screw caps (1).
2. Unscrew two screws (2).
3. Remove door handle (3).

Door handle is removed.

Install in reverse order.

Repair

4.3 Replacing easy opening handle

Required tools:

Phillips screwdriver PH2. Prerequisite: Appliance is disconnected from power supply. Door is open.

4.3.1 Removing easy opening handle

1. Remove easy opening handle cover (1).
2. Unscrew two screws (2).

Easy opening handle is removed.

4.3.2 Installing easy opening handle

Install in reverse order.

Repair

4.4 Replacing door upper hinge

Required tools:

Torx Bit TX20 6.3 mm (1/4") [00340865]

Heavy, bulky appliances!

Back and muscle injuries

• Appliance door removal operation should only be carried out by trained specialists. To move the appliance, two people are required. Use only suitable tools and equipment.

Sharp edges!

Cut injuries

Wear protective gloves.

Slipping of tilted appliances!

Bone fractures / crush injuries

• Secure appliances against slipping

Risk of falling parts due to released screws!

Injury because of falling parts.

• Secure component from falling down.

Risk of falling parts due to released screws!

Damage to other parts of the appliance or at customers home e.g. bot

n.

• Secure component from falling down.

Prerequisite:

Appliance is disconnected from power supply. Appliance interior fittings are removed.

1. Place appliance on the back side.

2.1. Press upper hinge cover on both sides (1).

1. Move out upper hinge cover (2).
2. Remove upper hinge cover (3).

Repair

3.1. Unscrew two screws (1).

1. Remove upper hinge (2).

Door upper hinge is removed. 4.4.2 Installing door hinge Install in reverse order.

Repair

4.5 Replacing door upper hinge (door with display)

Required tools:

Torx Bit TX20 6.3 mm (1/4") [00340865]

Warning

Heavy, bulky appliances!

Back and muscle injuries

Appliance door removal operation should only be carried out by trained specialists. To move the appliance, two people are required. Use only suitable tools and equipment.

Caution

Sharp edges!

Cut injuries

Wear protective gloves.

Warning

Slipping of tilted appliances!

Bone fractures / crush injuries

Secure appliances against slipping

Caution

Risk of falling parts due to released screws!

Injury because of falling parts. - Secure component from falling down.

Notice

Risk of falling parts due to released screws!

Damage to other parts of the appliance or at customer's home e.g. bottom.

Secure component from falling down.

• Danger

Risk of electric shock due to live parts!

Danger to life through electric shock in case of improper repair.

Danger to life through electric shock in case of improper repair

Electric parts should be repaired by qualified electricians. After the repair, have a safety test performed according to VDE 0701 or country-specific regulations.

Risk of electric shock due to live parts!

Risk of electric shock due to live parts!

Death by electrocution

• Disconnect appliances from electrical supply at least 60 seconds before starting repairs.

Prerequisite:

1. Appliance is disconnected from power supply. 2. Appliance interior fittings are removed.

Repair

1. Place appliance on the back side.

Repair

1. Press upper hinge cover on both sides (1). 2. Move out upper hinge cover (2). 3. Remove upper hinge cover (3).

1. Remove cable box cover (1). 2. Remove cable protection (2). 3. Disconnect electrical connection (3). 4. Unscrew two screws (4). 5. Remove upper hinge (5).

Door upper hinge is removed.

Install in reverse order.

Repair

4.6 Replacing door lower hinge

Required tools:

Torx Bit TX20 6.3 mm (1/4") [00340865]

Prerequisite:

The appliance is disconnected from the power supply. The appliance interior fittings are removed. The appliance is placed on its back.

The upper hinge is removed. (See page 128)

4.6.1 Replacing the door lower hinge

1. Remove the door.

2.1. Unscrew the screw (1).

1. Turn the lower hinge out (2).
2. Remove the lower hinge (3).

The lower hinge is removed.

Repair

Install in reverse order.

Repair

4.7 Replacing the shelf

Prerequisite: The door is open.

4.7.1 Removing the shelf

Pull out shelf.

Shelf is removed.

4.7.2 Installing shelf

Install in reverse order.

Repair

4.8 Replacing frozen food container

Prerequisite: Door is open.

4.8.1 Removing frozen food container

1. Pull out frozen food container all the way (1). 2. Remove frozen food container (2).

Frozen food container is removed.

4.8.2 Installing frozen food container

Install in reverse order.

Repair

4.9 Replacing ice maker

Prerequisite: Door is open.

4.9.1 Removing ice maker

1. Pull out shelf frozen food container with ice maker (1).
2. Release hooks (2). 3. Release hooks (3)
3. Remove ice maker (3).

Ice maker is removed.

4.9.2 Installing ice maker

Install in reverse order.

Repair

4.10 Replacing LED top light

Required tools:

Slotted screwdriver Blade 2.4 mm x 0.4 mm x 60 mm, in the kit [00341820]

Your appliance features a maintenance-free LED light.

These lights may be repaired by customer service or authorised technicians only!

Danger

Risk of electric shock due to live parts!

Danger to life through electric shock in case of improper repair

Electric parts should be repaired by a qualified electrician.

After the repair, have a safety test performed according to VDE 0701 or country-specific regulations.

Danger

Risk of electric shock due to live parts!

Death by electrocution

• Disconnect appliances from electrical supply at least 60 seconds before starting repairs.

Caution

Sharp edges!

Cut injuries

Wear protective gloves.

Prerequisite:

1. Appliance is disconnected from power supply. Door is open. Upper interior fittings are removed.

4.10.1 Removing LED light

1. Move the LED light to the left side.

LED light electrical connection is disconnected.

1. Release LED light hooks.

Repair

1. Remove LED light moving it forward.

LED light is removed.

4.10.2 Installing top LED light

Install in reverse order.

Remonditeave - Sögavkülmik

1 Selle dokumendiga seoses 139

1.1 Tahtis teave 139

1.1.1 Eesmark 139 1.2 Sumbolite selgitus 139 1.2.1 Ohutasemed 139 1.2.2 Ohusumbolid 139 1.2.3 Hoiatuste struktuur 140 1.2.4 Üldised sumbolid 140

Ohutus. 141

2.1 Uldised ohutusiuhised 141 2.1.1 Kofik kodumasinad 141

Mny avyicete TIOJovdc,ouMTpeiaqavopevwTov ouvdoewk KaT ovayuyuTw TAKETW.

EpyaIeia Kai BonOnmuata

Therefore, m = 3/11.

Therefore, m = 3/11.

Risk of electric shock due to live parts!

4.3 Replacing the easy opening handle 418

4.3.1 Removing the easy opening handle 418 4.3.2 Installing the easy opening handle 418

4.4 Replacing the upper door hinge 419

4.4.1 Removing the door hinge 419 4.4.2 Installing the door hinge 421

4.5 Replacing the upper hinge (door or display) 422

4.5.1 Removing the hinge 423 4.5.2 Installing the door hinge 424

4.6 Replacing the lower hinge 425

4.6.1 Replacing the lower hinge 425 4.6.2 Installing the lower hinge 426

Torx TX20 screwdriver bit 6.3 mm (1/4") [00340865]

Flathead screwdriver Blade 10 mm x 1.6 mm x 200 mm

Requirement:

4.3 Replacing the easy opening handle

Special tools:

Phillips screwdriver PH2 Requirement: The appliance is disconnected from the power supply. The door is open.

4.3.1 Removing the easy opening handle

1. Remove the easy opening handle (1).
2. Unscrew the two screws (2).

Torx TX20 6.3 mm (1/4") [00340865]

WARNING

Heavy, bulky appliances!

Risk of back injury and muscle strain

Torx TX20 6.3 mm (1/4") [00340865]

WARNING

Heavy, bulky appliances!

Risk of back injury and muscle strain

Torx TX20 6.3 mm (1/4") [00340865]

WARNING

Heavy, bulky appliances!

Back injury and muscle damage

4.3 Replacing the easy opening handle 441

4.3.1 Removing the easy opening handle 441 4.3.2 Installing the easy opening handle 441

4.3 Replacing the easy opening handle

Special tools:

4.3 Replacing the Easy opening handle 509

4.3.1 Removing the Easy opening handle 509 4.3.2 Installing the Easy opening handle 509

1. Press the entire gasket into the groove bit by bit.

4.3 Replacing the Easy opening handle

Required tools:

Phillips screwdriver PH2

Prerequisite:

The appliance is disconnected from the power supply. The door is open.

4.3.1 Removing the Easy opening handle

1. Remove the cover for the Easy opening handle (1).
2. Unscrew the two screws (2).

The Easy opening handle has been removed.

4.3.2 Installing the Easy opening handle