AS2300 - Vacuum Cleaner UFESA - Free user manual and instructions

USER MANUAL AS2300 UFESA

bagless vacuum cleaner

aspirateur sans sac

aspirador sem saco

uS 100

A

B

C

Estimado cliente!

Congratulations on your choice of our appliance, and welcome among the users of ufesa products. Please read these instructions carefully. Pay your special attention to important safety instructions. Keep this User's Guide for future reference.

Important safety instructions

DANGER! / WARNING! Health hazard

Do not operate the appliance if the cord, the housing or the handle is visibly damaged. In such a case, return the appliance to a service center.

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

The appliance can only be repaired by qualified service personnel. Improper servicing may cause a serious hazard to the user. In case of defects please contact a qualified service center.

Always the plug must be removed from the socket-outlet before cleaning, maintaining, assembling or dismantling the appliance.

Turn off the device and unplug it from an outlet before replacing the equipment or approaching moving parts during use.

Do not use the vacuum cleaner to clean people or animals, pay special attention to keep the nozzles away from eyes and ears.

• Do not use the vacuum cleaner to clean liquids or other damp dirt.

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

Only use the appliance indoors at room temperature and up to 2000 m above sea level.

CAUTION! Not observance can result in damage to possessions

Connect the vacuum cleaner only to a 220-240 V mains supply equipped with a 16 A fuse. Do not unplug by pulling on cord.

Do not run the vacuum cleaner or the brushes over the cord, it may cause damage to the cord insulation.

Do not use the vacuum cleaner without the filters installed in the vacuum cleaner or if the filters are damaged.

Do not pick up: matches, cigarette butts, hot ash.
Avoid picking up sharp objects.

Check the suction hose, the tubes and the nozzles -remove the dirt from the inside.

Do not vacuum fine dust such as: flour, cement, gypsum, toners for printers and copy machines etc. It is forbidden to cover up the air holes of the vacuum cleaner while it is working. Otherwise, the hot air has no way of exiting the vacuum cleaner, and this may lead to motor overheating causing a failure or a deformation of the plastic parts.

SUGGESTION Information on the product and suggestions for its use

This appliance is intended for domestic use only. Operate the appliance only in indoor spaces and vacuum only dry surfaces. Before vacuuming dry the carpets that were wet cleaned.

Vacuum cleaner is a universal device with a switchable sucking brush nozzle, which is used for vacuuming hard floors and carpets.

Technical parameters

The type of the vacuum cleaner and the technical parameters are indicated on the rating label. Mains protection 16 A.

Does not cause interferences with audio/video devices. Noise level: 83 dB(A).

Static electricity

In the process of vacuuming of some surfaces in areas of low air humidity the device may become electrically charged. It is a natural phenomenon - it does not damage the device, and it is not considered to be a fault. In order to minimize the phenomenon, we recommend you to:

• discharge the device by touching metal items in the room with the pipe,
• increase air humidity in the room,
• use widely available antistatic agents.

Appliance elements

1 Outlet filter cover
Suction brush fastening clip
3 Plug and cord
4 "CYCLONE" dust container fastening clip
5 ON/OFF button
6 Cord rewind button
7 Handle (for "CYCLONE" dust container)
8 Slider - mechanical regulator of the suction power
9 Suction hose
10 Telescopic suction tube
11 Outlet filter "Microfilter" (fitted inside the vacuum)
12 Basic EPA E10 filter (fitted inside "CYCLONE" dust container)
13 Basic EPA E10 filter (fitted inside "CYCLONE" dust container) shield
14 "CYCLONE" dust container (vacuum's removable module)
15 Upper lid of the "CYCLONE" dust container
16 Bottom lid of the "CYCLONE" dust container
17 Combination suction brush
18 Crevice nozzle
19 Small brush
20 Small nozzle

Preparing vacuum cleaner for operation

Insert the end of the suction hose in the vacuum's opening. Make sure that the splines on the hose's end fit into the special slots in the vacuum's inlet opening.
Turn the hose end clockwise until it clicks into place.
3 Connect the other end of the hose (handle) with the suction tube. In order to do it, press latch "A" and insert the tube into the hose's handle so that latch "A" is blocked in opening "B".
4 Adjust the telescopic suction tube to the desired length by sliding the slider according to the arrow and pull the tube out/in.
5 Attach the selected nozzle or brush to the other end of the suction tube.
Combination suction brush may be used to vacuum hard flooring and carpets. In order to vacuum hard surfaces - wooden, plastic floors, ceramic tiles,

etc. pull the brush out by pressing the switch on the suction brush according to the drawing when vacuuming carpets, hide the brush (set the switch on the suction brush to "")
7 Grab the plug (3) and pull the cord out.

When pulling the power cord out, beware of the yellow stripe signaling the end of the cord. Persistent pulling (pulling on), may damage the cord.

Insert the plug into the power outlet.

Before starting the vacuum, make sure that both "CYCLONE" dust container has been fitted with the basic EPA E10 filter and the outlet filter has been installed.
Switch the vacuum cleaner on by pressing ON/OFF button.
10 Your vacuum cleaner is fitted with mechanical suction regulator located on the hose handle. You may use it to temporarily and slightly correct the suction power.

Dismantling/attaching "CYCLONE" dust container

Your vacuum cleaner comes with a removable "CYCLONE" dust container (vacuum's removable module) that collects and holds the dirt. When "CYCLONE" is full, you need to empty it.

Your vacuum cleaner is equipped with safety valve located inside the vacuum's

compartment. It opens automatically, when the suction hose or any of the elements attached to it get choked or "CYCLONE" dust container is overfull. Once the valve opens, you will hear a distinctive "whirring" sound coming out of the machine.

Switch the vacuum off by pressing ON/OFF button (5).
2 Remove the plug from the power outlet.
Turn the suction tube end counterclockwise and remove it from the inlet opening.
4 Disconnect "CYCLONE" dust container from the vacuum. In order to do it, press the dust container clip and swerve it away by holding the handle in the upper lid of the dust container.
5 Move "CYCLONE" over the dust bin and press the clip on the bottom lid and empty the container.

Now you should check EPA E10 basic filter and if necessary, clean or replace it.

6 Close the bottom lid of the "CYCLONE" dust container until you hear the click.

"CYCLONE" must be tightly closed. Otherwise, the suction power may be reduced.

7 Attach the emptied "CYCLONE" dust container to the vacuum until you hear the click.

It is necessary to empty "CYCLONE" dust container when you notice that:

a) your vacuum cleaner is vacuuming less effectively, b) dust container is full.

Filter disassembly

Your vacuum cleaner comes with "CYCLONE" dust container with cyclone filtration enabling you to vacuum without the need to use traditional bag. Characteristically, cyclone filter uses the phenomena of the spinning stream of air in order to separate solid contaminants. Contaminants are separated in the circular part of the container, where the spinning air throws them at the container's wall; later they are moved to the container's next chamber. Pre-cleaned air is directed to EPA E10 filter that picks up and holds the finest dust fractions. This washable EPA E10 filter has been fitted with a special filtering material to enable rinsing the dirt under running water and reusing the filter. The vacuum's outlet is fitted with "Microfilter" outlet filter.

In case both filters: EPA E10 basic filter (12) and "Microfilter" (11) get dirty, you can replace them with the new ones, clean or rinse them under running water

You may not wash your filters in the washing machine or dishwasher.

Filters may be dried only naturally.

You may not blow dry your filters or place it on the heaters or radiators.

Before you replace the filters, make sure the vacuum is switched off and the plug is removed from the power outlet.

EPA E10 BASIC FILTER

It is necessary to clean EPA E10 basic filter from the fine dust fractions.

Dismantle "CYCLONE" dust container according to item C.

Turn the upper lid of "CYCLONE" container to position open and remove the lid. If the container is full, empty it in accordance with item C.
2 Undo EPA E10 filter, removing it from the upper lid of "CYCLONE" towards "the symbol and the direction marked by an arrow are located next to the basic filter EPA E10 handle).
3 Remove the shield from the filter.
4 Clean, wipe and dry the shield thoroughly.

• Clean the basic filter's belts (12), if your filter is damaged, you must replace it with a new one. If EPA E10 (12) has been soiled, you may replace it with a new one, clean or rinse it under running water. Remember to dry the filter before you reattach it.

For safety reasons, attaching damp or damaged EPA E10 filter (12) is not acceptable.

Insert the cleaned shield into the new/rinsed EPA E10 filter.
Make sure the slides on the protective flange are fitted into the slots on filter hosing.
6 Reattach EPA E10 basic filter to its previous position in the upper lid of the dust container (symbol "along with the direction marked by an arrow is provided next to EPA E10 handle.
Place the upper lid back over "CYCLONE" dust container and turn it to the position closed
8 Attach "CYCLONE" container to the vacuum until you hear the click.

It is recommended to replace EPA E10 basic filter (12) every 6 months of operation.

Damaged EPA E10 filter should always be replaced with a factory new and original item.

"MICROFILTER" OUTLET FILTER

In order to replace "Microfilter" (11) press the filter cover interlock and remove the outlet filter cover.
2 Remove the filter from the cover.

If the "Microfilter" (11) gets dirty, you can replace it with a new one, clean or rinse it. Remember to dry the filter before you reattach it.

For safety reasons, attaching damp or damaged "Microfilter" is not acceptable.

3 Carefully place the new/rinsed filter in the outlet filter cover according to the cutting.
Place the filter cover back making sure that the two slides located in the bottom part of the cover fit into the slots on the vacuum's hosing, press the cover in order for the clip to lock in the hosing. The click you hear confirms that the outlet filter cover has been correctly attached.

Damaged "Microfilter" should always be replaced with a factory new and original item.

End of operation, cleaning and maintenance

Switch the vacuum off by pressing ON/OFF button (5).
2 Remove the plug from the power outlet.
3 Wind the cord by pressing cord rewind button (6). While doing it, remember to hold the cord to make sure it does not get tangled and the plug does not hit the vacuum's hosing.
4 Disconnect the telescopic tube and the nozzle on the brush.
5 Disconnect the telescoping suction tube from the hose. In order to remove the telescopic handle from the hose handle, press latch "A" and pull the tube towards the arrow.
Turn the suction tube end counterclockwise and remove it from the inlet opening.
7 Your vacuum cleaner may be stored in horizontal position. Insert the fastening hook of the suction brush into the clip fastening the suction brush located on the back of the vacuum, next to the power cord outlet. The hose may stay fastened to the vacuum cleaner, but make sure that it is not bent too hard when stored.

If necessary, the vacuum's housing and compartment may be wiped with a wet cloth (it may be moistened with a detergent), dried or wiped until dry.

Do not use scouring agents or solvents.

Problems that may occur when operating the vacuum

PROBLEM WHAT TO DO

The vacuum switched off during the operation - thermal fuse turned on.
Until the vacuum cools down, do not attach "CYCLONE" dust container.

• Switch off the vacuum cleaner, remove the plug from the power outlet and wait for about 40 minutes until you switch it on again.
• Remove, empty and clean "CYCLONE" dust container, clean EPA inlet filter.
• Check and clean the accessories: suction hose, tubes, nozzles and brushes.
• Reassemble the vacuum and start it up again.
  If the thermal fuse keeps turning on way too often or if you are unable to switch the vacuum cleaner on again after it cooled down, please take the vacuum cleaner to the service.

You can hear the "whirring" sound.

• Check "CYCLONE" dust container and the fittings, remove the clog or empty and clean the "CYCLONE" dust container.
• Replace or clean the filters.

Your vacuum cleaner is not working efficiently enough.

Empty and clean "CYCLONE" dust container, replace or clean the filters, check the suction tube, hose and nozzle -remove the clog.

Power installation fuse went on.

Check whether there are other electric appliances plugged into the same electric circuit, if the fuse turns on repeatedly, take the vacuum cleaner to the service.

PROBLEM WHAT TO DO

Your vacuum cleaner fails to work, the housing is damaged or the power cord is damaged.

Take your vacuum cleaner to the service.

Disposal

Dispose of packaging in an environmentally-friendly manner. Our goods come in optimised packaging.

This basically consists in using non-contaminating materials which should be handed over to the local waste disposal service as secondary raw materials.

This appliance is labelled in accordance with European Directive 2012/19/EU concerning used electrical and electronic appliances (waste electrical and electronic equipment

• WEEE). The guideline determines the framework for the return and recycling of used appliances as applicable throughout the EU. Please ask your specialist retailer about current disposal facilities.

The manufacturer does not accept any liability for any damages resulting from unintended use or inappropriate handling. The manufacturer reserves his right to modify the product any time in order to adjust it to the law, standards, directives, or due to construction, trade, aesthetic or other reasons, without prior notice.

Cher client!

A. 5 J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J

e 1

y

"Microfilter"

3

JU 1

4

aalglgo wulutl bll no laaw jjg gag

Sauu Sui bai lce baoi pia aui Soal pgb 1e o2gol

JSSs Jss sss

.8joo gww

"Microfilter"

.

woll

"CYCLONE" jg 00000000000000000000000000000000000000000000000000000000000000000000000000000000000

EPA E10 25 111 111 111 111 111 111 111 111 111 111 111 111 111 111 111 111 111 1

a 1

J 1

Jc p2e no 25T clawrll Jdowl Jg 1111111111111

EPA E10

EPA E10 5 5

C C

ON/OFF jj bfaall 9 (J

baiol pao go aalgo cly aolll ay jy Sall aaiSoll 10
paoioll plaoai lcs. gab jll aay ygall sullsall
aagbg ao Jsw baaiil ab

Jy / CYCLONE

CL "CYCLONE" 15 aagglg0a yjyssll ssoll 15 15 15 15 15 15 15 15 15 15

Jolol plaoe ydoa aal aasall g 10
glsl sie 15ab plaaal g aasall o
dol zg 4 aenll g baiI pgb
"ogw gaww plaaal g jll gl
.aisall no

ON/OFF jj 1

aIbI J 2

4c jilg aclll bll c 05e bawb wB

CCLL 4
J 100000000000000000000000000000000000000000000000000000000

5 5

EPA E10 2n n 2n

CYCLONE" 6

yKoL CYCLONE" 1000000000000000000000000000000000000000000000

. 12) aaswll jy wss cbbj y 7
0

CYCLONE" yglalg 100
. JlJlJSyAaSsll Joc (
Jglal

"CYCLONE"

（J）ON/OFF

山

(CYCLONE)

baaJI aIbI gJlsO pbiio -aijoll

baaillgbs

Sulllb

(aissoll s)“Microfilter"

JELIJI 10

(CYCLONE)

Iaag baaal alw jglc gaoallglaal

cIaalb bfo 2joc)olfoal lfofofofofofofofofofofofofofofofofofofofofofofofofofofofofofofofofofofofofofofofofofofofofofofofofofofofofofofofofofofofofofo

"baaill blae jgogll

（3）

aal bai aai aai aai aai aai aai aai

y

gI gS Joll jll all oJg aJyRgSll aasoll Joos

aai 15

.1JLlI JIJI,JIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJIJ

.5allllblll

aillj p - algllg uullgl baaal gcb

Jd1110 1

j> j#ll. caiy) 1: Joo pcll lal

.

aill 151 aiiisolly 3gogall gagll clll lio

C

a 128 aaioll

aSwUJ1joggUbc Udo

1

Jg

(1)

jiooll pdo wiao jaoill 1
jaii bwl4 wsiog boi jioil jol jaoi i
Iy e laa bi pi y l aowll aai ay siil

a baa aog o2g jolc jge JySll aaiSoll

Jg

gll aai

a aaii

16 11

gall/gawgolljegy

(1)JUNDS 83:

a

jgl jg jybjlll lgl bliol gcbwll jae wssic

iL Lclauai oalll no sall j 1n .

U

a
.
.

jolol

C. = , =

baaill bawj ccaaa

aal

1

2

3

.

g

Jg jnnn n nn

.

8 8

J 1

aalllg aegwll glaowjll

JgddjIg

J 1

aaleeil pcl bcgl pde

jgljglg

jblolgogpfoio

y j 1.4 abjrol

poo j 1. jjlll JbJl

jIJI IiIgog JIbJl

.

.

2000 1

. 1

1

a

JUOW

g jyj yj 1

16gagraia240-220

LJ

lllglg jnojw all yg aIyRSLI gSsIg

J 1

y

gdoa aie 1000 jig liqaiol pJlui 1000

.UFESA

aolplaaalglg 4y jlll lglgco ool gj y Jaiu wJy aaiwU W Jlll lq bao. aalll

auiisol Joee

yo 0ooh olae

jIeJI|Jz JIoEoi IeBii

1/！

aall aill jbi

1

p 1110 .

.

gaioll 1j j

gA

uunnnn nn nnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn

.

J 1

e e .

Jus Jbs awwlaa Jbc 4os

.

Joo 1

1

. jie jie jie jie jie jie jie jie jie jie jie

Jd

J 1

. 110001 15 45 2 2 2 6

ufesa

BSH Electrodomesticos Espana S.A.

Ronda del Canal Imperial de Aragon, 18-20

50197 Zaragoza, SPAIN

C.I.F.: A-28-893550

51-16

9001270360