HATS9DS6BPLWI - Basket HAIER - Free user manual and instructions

USER MANUAL HATS9DS6BPLWI HAIER

CONFORMITY WITH DIRECTIVES

1INTRODUCTION Thank you for choosing this cooker hood. This instruction manual is designed to provide you with all required instructions related to the installation, use and maintenance of the appliance. In order to operate the unit correctly and safety, please read this instruction manual carefully before installation and usage. The cooker hood uses high quality materials, and is made with a streamlined design. Equipped with large power electric motor and centrifugal fan, it also provides strong suction power, low noise operation, non-stick grease filter and easy assembly installation. Hereby, Candy Hoover Group Srl declares that the radio equipment is in compliance with Directive 2014/53/EU and with the relevant Statutory internet address: www.candy-group.com SAFETY PRECAUTION Never let the children operate the machine. The cooker hood is for home use only, not suitable for barbecue, roast shop and other comme rcial purpose. The cooker hood and its filter should be clean regularly in order to keep in good working condition. Clean the cooker hood according to the instruction manual and keep the unit from danger of burning. Forbid the direct baking from the gas cooker. Please keep the kitchen room a good convection. Before connecting this appliance check that the power supply cord is not damaged. A damage supply cord must be replaced by qualified service personnel only. There shall be adequate ventilation of the room when the range hood is used at the same time as appliances burning gas or other fuels; The air must not be discharged into a flue that is use d for exhausting fumes from appliances burning gas or other fuels; Regulations concerning the discharge of air have to be fulfilled. Requirements (for the UKCA market). The full text of the declaration of conformity is available at the following 2Electrical Shock Hazard

Only plug this unit into a properly earthed outlet. If in doubt seek advice from a suitably qualified engineer.

Failure to follow these instructions can result in death, fire, or electrical shock. 5IFTFTIBMMCFBEFRVBUFWFOUJMBUJPOPGUIFSPPNXIFOUIFSBOHF IPPEJTVTFEBUUIFTBNF UJNFBTBQQMJBODFTCVSOJOHHBTPSPUIFS GVFMTOPUBQQMJDBCMFUPBQQMJBODFTUIBUPOMZEJTDIBSHFUIFBJSCBDL JOUPUIFSPPN UIFEFUBJMTDPODFSOJOHUIFNFUIPEBOEGSFRVFODZPGDMFBOJOH UIFSFJTBGJSFSJTLJGDMFBOJOHJTOPUDBSSJFEPVUJOBDDPSEBODFXJUIUIF JOTUSVDUJPOT EPOPUGMBNFVOEFSUIFSBOHFIPPE $"65*0/"DDFTTJCMFQBSUTNBZCFDPNFIPUXIFOVTFEXJUI DPPLJOHBQQMJBODFT - Children should be supervised to ensure that they do not play with the appliance. - Do not flambé under the range hood. The range hood is not intended to be installed over a hob having more than four hob elements The lamp used in this product is not suitable for use in the lighting of a room. The purpose of this lamp is to provide illumination for using the product. 3Direct Connection The appliance must be connected directly to the mains using an omnipolar circuit breaker with a minimum opening of 3mm between the contacts. The installer must ensure that the correct electrical connection has been made and that it complies with the wiring diagram. The cable must not be bent or compressed. Regularly check the power plug and power cord for damage. If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.

WARNING: This is a Class I appliance and MUST be earthed

This appliance is supplied with a 3 core mains cable coloured as follows: Brown = L or Live Blue = N or Neutral Green and Yellow = E or Earth The fuse must be rated at 3 Amps. Electrical Installation All installation must be carried out by a competent person or qualified electrician. Before connecting the mains supply ensure that the mains voltage corresponds to the voltage on the rating plate. 4Standard Installation Accessories List Spec. Qty Casing 1 Upper Chimney 1 Lower Chimney 1 Lower chimney bracket 1 Upper chimney bracket 1 Hanging Board 1 φ8 rawl plugs φ8×φ6 white color

If you have an outlet to the outside, your cooker hood can be connected as below picture by means of an extraction duct (enamel, aluminum, flexible pipe non flammabe with an interior diameter of 150mm)

1. Before installation, turn the unit off and unplug it from the outlet.

2. The cooker hood should be placed at a distance of 65~75cm above

the cooking plane for best effect.

3. Drill 3 x 8mm holes to accommodate the bracket. Screw and tighten

the bracket onto the wall with the screws provided. Wall plug Wall bracket 107.5mm Screw(4mm x 30mm)

64. Leave up the cooker hood and hang onto the wall bracket hook.

5. Fix the one-way-valve to the air outlet of the cooker hood. Then,

attached the exhaust pipe onto the one-way-valve as shown below. Exhaust pipe Cooker hood

i. Place the glass in appropriate position on the top the cooker

ii. Fix with 4 screws and washer. In order to avoid the glass

cracking, please do not tighten the screws too strongly.

i. By Put the inner chimney into outer chimney .Then pulling out

the inner chimney upwards. Adjust to reach the height required.

ii. Sliding the chimney to adjust the chimney height. When the

height you required is reached, then hang the fixing hole to the fixing screws as showed in below pictures. Inner chimney Outer chimney

i. Drill 2 x 8mm holes to accommodate the plate II. Screw and

tighten the plate II onto the wall with 2 screws provided.

ii. Assembly the chimney onto the unit and fix it with 2 screws.

i/PUF5IFQSPEVDUJTQSPWJEFEXJUIWGMBQBDDFTTPSZ5IJT BDDFTTPSZJTOPUNBOEBUPSZGPSJOTUBMMBUJPOPQFSBUJPOBOEVTFPG UIFQSPEVDUw 12INSTALLATION (VENT INSIDE) If you do not have an outlet to the outside, exhaust pipe is not required and the installation is similar to the one show in section “INSTALLATION (VENT OUTSIDE)”. Activated carbon filter can be used to trap odors. In order to install the activated carbon filter, the grease filter should be detached first. Press the lock and pull it downward. Plug the activated carbon filter into the unit and turn it in clockwise direction. Repeat the same on the other side. NOTE: o Make sure the filter is securely locked. Otherwise, it would loosen and cause dangerous. o When activated carbon filter attached, the suction power will be lowere 13Intended Use Please read this user manual thoroughly before attempting to use this plasma filter for the first time. This manual contains important information on safe installation, use and care of this filter. Retain these instructions for future reference and pass on to the next user. This plasma filter can only be used safely if it is correctly installed according to the safety instructions. The installer is responsible for ensuring that the appliance works correctly at its installed location. This plasma filter is intended for domestic use and household environment only. Do not use the plasma filter for other uses than its specific purpose. Do not leave the appliance unattended during operation. This plasma filter is intended to remove airborne dust particles, pollen, micro-organisms (house dust mites, bacteria, viruses and moulds), cigarette smoke and smells from the air. Presence of smell will still be present when you are cooking and can only be completely removed after you had finished your cooking. Harmful gases (carbon monoxide etc.) cannot be removed. The plasma filter produces ozone, the amount will depend on the time you use the filter. When the plasma filter is placed in a well ventilated room, the amount emitted is within the set safety limits and standard. A slight ionisation smell will be present during usage and do not indicate a faulty connection or device This appliance may be used by children over the age of 8 years old and by persons with reduced physical, sensory or mental capacity or by persons with a lack of experience or knowledge if they are supervised by someone who is responsible for their safety or have been instructed in how to use the appliance safely and have understood the risks involved in not using it properly. Children must not play with the appliance. Cleaning and user maintenance must not be performed by children unless they are over 15 years of age and are supervised. Keep children below the age of 8 years old at a safe distance from the appliance and power cable. Check the appliance for damage after unpacking it. Do not connect the appliance if it has been damaged during transport. Important This plasma filter is intended for use in combination with an extractor hood with metal grease filters The manufacturer is not liable for any damage which is caused by improper use or incorrect operation. 14Operating Instructions

Warning: Only use the plasma filter in combination with an extractor unit with metal

grease filters. Always ensure that the plasma filter is in a location with good oxygen supply and good permanent ventilation. Please refer to your extractor hood user manual. Operating the Plasma Filter on the Extractor Hood Touch the sensor buttons gently on the control panel on the extractor to operate this appliance. To achieve better air extraction, it is advisable to switch on the extractor hood a few minutes before starting to cook and leave it on for approximately 15 minutes after cooking or at least all cooking smell is completely removed. The plasma filter uses a sensor switch that reacts to the air flow from the extractor hood. When the extractor hood is switch ON, the air pass through a sensor to activate the plasma filter automatically. It may take approximately 20 to 30 seconds to activate the plasma filter depending on the type of extractor hood. The indicator lamp on the plasma filter will light up and an audio signal will sound to indicate that the plasma filter is now switch ON. Cleaning the Plasma Filter Little maintenance is needed as the plasma filter is cleaned automatically as soon as it is put into operation. The electrodes exhibit a very long lifetime and are nearly indestructible in destined operation. The activated carbon filter is regenerated at each process, keeps its pores clean and is expected to last for not less than 6 years if the activated carbon filter is use for not more than 4 hours a day. Usage of more than 4 hours a day will reduce the lifespan of the activated carbon filter. Note: It is important to follow the maintenance instructions of your extractor hood. The grease filter must be clean regularly and/or replace at appropriate intervals to prevent contamination. Periodic Maintenance for Plasma Filter To ensure that your plasma filter is in satisfactory working condition, contact your local After Sales Center once every 5 years to do periodic inspection on the plasma filter. 15Trouble Shooting Problem Possible Cause Solution The Plasma Filter Does Not Work No electricity supply Check power plug is connected properly and main power switch is turned on Faulty Fuse Check the fuse box of the plasma filter to ensure fuse is not blown Power Trip Check if other electrical appliance are working The Indicator Lamp on the Plasma Filter Did Not Light Up Air Sensor Switch might be faulty Please contact your local After Sales Center PCB Board Failure 16Wi-Fi Connection Long press WiFi icon and enter into connecting mode: the backlit of WiFi icon keep flashing indicate the connection is under connecting, the backlit of WiFi icon is light on indicate it is connected, same for standby mode; long press WiFi icon again and the connection will be stopped;

DESCRIPTION OF COMPONENTS

OPERATION Boost 1(speed 4) Press speed b button 1, the backlit of speed B button is on, and the cooker hood is working at boost mode ; Boost 2(speed 5) Press speed b button 2, the backlit of speed B

button is on, and the cooker hood is working at boost mode ; Light Short press for lighting on & off Quick timer: Long press the light button hold for 3 seconds, fan speed buttons will flashing & into 5minutes count down, after 5 minutes motor & light will turn off automatic with three Buzzer sound. Medium Speed button Airflow speed is ideally for ventilation in standard cooking operation. High Speed button When high density of smoke or steam produced, press high-speed button for high effective ventilation. CONFIGURATION 1 Low Speed button It’s used for Ventilation on the kitchen. It is suitable for simmering and cooking which do not make much steam. 17STANDBY MODE. After plug in, all lighting, system in STANDBY MODE

Medium Speed button Airflow speed is ideally for ventilation in standard cooking operation.

High Speed button When high density of smoke or steam produced, press high-speed button for high effective ventilation. Booster function This hood has a booster function. To activate the booster, Press to speed 4, enter into highest speed while the hood is in use and it will increase speed for 5 minutes, before slowing down again. Light Short press for lighting on & off Quick timer: Long press the light button hold for 3 seconds, fan speed buttons will flashing & into 5minutes count down, after 5 minutes motor & light will turn off automatic with three Buzzer sound. CONFIGURATION 2 Wi-Fi Connection Long press WiFi icon and enter into connecting mode: the backlit of WiFi icon keep flashing indicate the connection is under connecting, the backlit of WiFi icon is light on indicate it is connected, same for standby mode; long press WiFi icon again and the connection will be stopped; Low Speed button It’s used for Ventilation on the kitchen. It is suitable for simmering and cooking which do not make much steam. 18Download hOn App First of all, you should download hOn APP and install to your portable device. Then enroll your hood. NOTE

ENROLLMENT HAIER HOOD

1- Press the WiFi button until the icon starts blinking When the pairing is

completed the WiFi icon will be on. The image of the hood has the only purpose of presenting it. May not be perfectly representative. 19MAINTENANCE Before cleaning switch the unit off and pull out the plug.

Use a soft cloth moistened with hand-warm mildly soapy water or household cleaning detergent. Never use metal pads, chemical, abrasive material or stiff brush to clean the unit.

II. Monthly Cleaning for Grease Filter

ESSENTIAL: Clean the filter every month can prevent any risk of fire. The filter collects grease, smoke and dust…... so the filter is directly affecting the efficiency of the cooker hood. If not cleaned, the grease residue (potential flammable) will saturate on the filter. Clean it with household cleaning detergent.

III. Annual Cleaning for Activated Carbon Filter

Apply SOLELY to unit that installed as a recirculation unit (not vented to the outside). This filter traps odors and must be replaced at least once a year depending on how frequent the cooker hood used.

IV. Changing a light bulb

Remove the screws on the glass, take off the hood glass. Find the bulb that requires replacement, you will find it located in the light fixture which is inside the exposed section of the canopy. Disconnect the light wiring point and remove the bulb holders and wiring from the hood. Important: It’s not possible to replace the bulbs individually, it will be necessary to obtain the bulbs, bulb holders and wiring as a complete part. (LED light: MAX 1.5W) Fit the replacement bulbs, bulb holders and wiring in the same manners as the originals. Then reconnect the light wiring point. 20Refit the hood glass and fasten the glass screws. Make sure the screws are fully tightened. TROBULESHOOTING Fault Cause Solution Light on, but fan does not work The fan blade is jammed. Switch off the unit and repair by qualified service personnel only. The motor is damaged. Both light and fan do not work Halogen light bulb burn. Replace the bulb with correct rating. Power cord looses. Plug in to the power supply again. Serious Vibration of the unit

The fan blade is damaged. Switch of the unit and repair by qualified service personnel only. The fan motor is not fixed tightly. Switch off the unit and repair by qualified service personnel only. The unit is not hung properly on the bracket. Take down the unit and check whether the bracket is in proper location. Too long distance between the unit and the cooking plane Readjust the distance to 65-75cm Suction performance not good Technology Wi-Fi Standard 802.11 b/g/n Frequency Band(s)[MHz] 2400 MHz - 2483.5 MHz Maximum Power[mW] 100 mW Product information for networked equipment power consumption of the product in networked standby if all wired network ports are connected and all wireless network ports are activated:

If the Hood has been enrolled with the APP, turn on the Hood to activate wireless network port. How to activate wireless network port: If the Hood has been enrolled with the APP, turn off the Hood to deactivate wireless network port. If the Hood hasn’t been enrolled with the APP, wireless network port will be deactivated even theHood is on. How to deactivate wireless network port: 21treatments, in order to remove and dispose properly all pollutants, and recover and recycle all materials. Individuals can play an important role in ensuring that WEEE does not become an environmental issue; it is essential to follow some basic rules: WEEE should not be treated as household waste; WEEE should be handed over to the relevant collection points managed by the municipality or by registered companies. In many countries, for large WEEE, home collection could be present. In many countries, when you buy a new appliance, the old one may be returned to the retailer who has to collect it free of charge on a one-to-one basis, as long as the equipment is of equivalent type and has the same functions as the supplied equipment.

CUSTOMER ASSISTANCE SERVICE

If you cannot identify the cause of the operating anomaly, switch off the appliance and contact the Assistance Service. PRODUCT SERIAL NUMBER. Where can I find it? It is important you to inform the Assistance Service of your product code and its serial number (a 16 character code which begins with the number 3); this can be found on the guarantee certificate or on the data plate located on the appliance. It will help to avoid wasted journeys to technicians, thereby (and most significantly) saving the corresponding callout charges. This appliance is marked according to the European directive 2012/1 9/EU on Waste Electrical and Electronic Equipment (WEEE). WEEE contains both polluting substances (which can cause negative consequences for the environment) and basic components (which can be re-used). It is important to have WEEE subjected to specific