00137427 - Power bank HAMA - Free user manual and instructions

USER MANUAL 00137427 HAMA

Thank you for choosing a Hama product. Take your time and read the following instructions and information completely. Please keep these instructions in a safe place for future reference. If you sell the device, please pass these operating instructions on to the new owner.

1. Explanation of Warning Symbols and Notes

Warning This symbol is used to indicate safety instructions or to draw your attention to specic hazards and risks. Note This symbol is used to indicate additional information or important notes.

• Wireless Charge Power Pack, 6000 mAh

• These operating instructions

• The product is intended for private, non-commercial use only.

• Protect the product from dirt, moisture and overheating, and only use it in a dry environment.

• Keep this product, as all electrical products, out of the reach of children!

• Do not drop the product and do not expose it to any major shocks.

• Do not operate the product outside the power limits given in the specications.

• Do not open the device or continue to operate it if it becomes damaged.

• Dispose of packaging material immediately according to locally applicable regulations.

• Since the battery is integrated and cannot be removed, you will need to dispose of the product as a whole. Do this in compliance with the legal requirements.

• Do not modify the product in any way. Doing so voids the warranty.

4. Getting started and Operation

4.1 Charging the Power Pack

• Start charging the power pack by connecting the integrated USB connecting cable to a suitable USB charger.

• Please refer to the operating instructions for the USB charger used.

• Charging begins and ends automatically.

• Charge the Power Pack fully before using it for the rst time. Note – Capacity

• The capacity is always shown when the Power Pack is charging.

• Each status LED corresponds to 25% of the capacity. When an LED is permanently illuminated, this indicates that this capacity level has already been reached. The Power Pack is charged to at least 75% if three LEDs are illuminated, and the fourth is ashing.

• If all four status LEDs light up, the full capacity is available.

• All LEDs switch off when charging is complete. Warnung – Battery

• Only use suitable charging devices or USB connections for charging.

• As a rule, do not charge devices or USB connections that are defective and do not try to repair them yourself.

• Do not overcharge the product or allow the battery to completely discharge.

• Avoid storing, charging or using batteries in extreme temperatures.

• When stored over a long period of time, batteries should be charged regularly (at least every three months). G Operating instruction3 4.2. Charging terminal devices via USB connecting cable

• Connect the integrated Micro-USB connecting cable (OUT 5 V/2.1 A) to the Micro-USB port of your terminal device (mobile phone, smartphone, etc.).

• The integrated connecting cable may not be suitable for the USB port of your terminal device. In this case, use the USB cable that was included with your terminal device.

• To start charging, press the button on the power pack. The status LEDs show the remaining capacity when the power pack is charging.

• The current battery status of your terminal device will appear on this device.

• Press the button on the power pack to stop charging and to switch it off. The status LEDs will go out.

• The power pack will automatically switch off after a few seconds if it is not connected to a terminal device. Warning – Connecting terminal devices

• Before connecting a terminal device, check whether the power output of the charger can supply sucient power for the device.

• Ensure that the total power consumption of all connected terminal devices does not exceed 2100 mA.

• We recommend that you always use just one of the two USB ports.

• Please refer to the instructions in the operating manual of your terminal device.

• It is essential that you observe these specications and the safety instructions regarding the power supply of your devices. 4.3. Charging terminal devices via inductive charging plate

• Set your terminal device with the back on the charging plate.

• Charging starts as soon as an effective induction eld has been generated. The current charging status appears on your terminal device.

• If no connection can be established through induction, you may have to change the position of your terminal device.

• Charging stops automatically once your device’s battery is fully charged.

• Remove your terminal device from the charging plate. Note

• For charging a terminal device with the induction charger, your terminal device has to be compatible with the induction charging technology. Please read the operating instructions of your device.

• Please note that mobile phone sleeves, covers, etc. and other materials between the induction charger and the backside of your terminal device disturb or prevent actually the charging process.

5. Care and Maintenance

Only clean this product with a slightly damp, lint-free cloth and do not use aggressive cleaning agents.

6. Warranty Disclaimer

Hama GmbH & Co. KG assumes no liability and provides no warranty for damage resulting from improper installation/mounting, improper use of the product or from failure to observe the operating instructions and/ or safety notes.4

7. Service and Support

Please contact Hama Product Consulting if you have any questions about this product. Hotline: +49 9091 502-115 (German/English) Further support information can be found here: www.hama.com

• Wireless Charge Power Pack, 6000 mAh