Compact 213100 - Food Processor PRINCESS - Free user manual and instructions

Frequently Asked Questions - Compact 213100 PRINCESS

USER MANUAL Compact 213100 PRINCESS

Ooyniecs xpnsncs EAnyivka 50

1

2

4

1

Algemeen

This attractive blender has been designed by Jan des Bouvrie. The appliance can be used to finely chop fruit and vegetables or to make delicious shakes and juices. It can also be used to grind pepper and herbs. Both the housing and the jugs are of a modern and luxurious design.

The Jan des Bouvrie Blender has a powerful motor with two speed settings and a pulse setting.

The jug has a lid with an opening through which it can be filled. Products can be added through this opening whilst blending without making a mess. The jug has a volume of 0.8 liters. Steel knives are integrated in the jug, so that the blender can easily chop and puree both large and small pieces of fruit and vegetables.

This model comes with one extra universal mill for grinding the harder sorts of food (such as peeled walnuts). This mill has a removable blade stand with integrated knives.

The device must be connected to the mains power supply.

Operation and controls

See figure 1.

The appliance consists of the following components:
1 Housing
2 Power cord and plug
3 Operation indicator light (orange)
4 On/Off indicator light (red)
5 Rotary button
6 Jug (volume 0.8 liters)
7 Filler cap
8 Lid
9 Universal mill
10 Mill blade stand (removable)

Before using for the first time

1 Remove all the packaging materials and stickers from the appliance.
2 Clean the appliance and all the accessories (see 'Cleaning and maintenance') and dry them thoroughly.

Blending products

See figure 2.

1 Place the housing on a stable surface.
2 Fit the jug to the housing. The three catches on the housing must fit precisely into the slots in the base of the jug.
3 Place the lid on the jug.
4 Place the filler cap in the lid and tighten the filler cap by rotating it a quarter of a turn.
5 Cut the fruit and/or vegetables into pieces. Do not make the pieces too large. They must be small enough to fit into the bottom of the jug.
6 Open the lid and put the pieces in the jug.
7 Place the lid back onto the jug to prevent splashing.
8 If the rotary button is in 0-position and pushed in, the button is locked. Push the rotary button to unlock it (see figure 2).
9 Switch the blender a few seconds to setting 1 or 2 or the pulse setting (P). This blender works very fast. In seconds the product will be chopped. The longer the blender is turned on, the finer the products will be chopped.

Note: Do not operate the blender more then 3 minutes to avoid overheating. Let the blender cool down for a few minutes before starting again.

10 If necessary, you can top up the jug by opening the filler cap. Unscrew it a quarter of a turn and remove it from the lid. If the pieces to be added do not fit through the filler opening, turn off the blender, remove the lid and place the pieces in the jug. Place the lid back on the jug before turning the blender back on.

11 Switch off the blender (position 0) once the required quantity of fruit and/or vegetables have been chopped.
12 Push the rotary button to lock it (see figure 2).
13 Remove the plug from the plug socket.

Grinding

See figure 4.

1 Place the housing on a stable surface.
2 Fit the mill to the housing. The three catches on the housing must fit precisely into the slots in the base of the mill.
3 Rotate the top plate of the mill clockwise to open the mill-jug.
4 Fill the mill jug with the product that you wish to grind.
5 Rotate the top plate of the mill anti-clockwise to close the mill-jug.
6 If the rotary button is in 0-position and pushed in, the button is locked. Push the rotary button to unlock it (see figure 2).
7 Switch the mill a few seconds to setting 1 or 2 or the pulse setting (P).

This mill works very fast. In seconds the product will be ground. The longer the mill is turned on, the finer the products will be ground.

Note: Do not operate the mill more than 50 seconds with max. 150g ingredients. Let the mill cool down for around 7 minutes before starting again.

8 Switch off the mill (position 0) once the required quantity has been ground.
9 Push the rotary button to lock it (see figure 2).
10 Remove the plug from the plug socket.
11 Wait until the blades stand still and remove the ground product.

Cleaning and maintenance

• Make sure the plug has been removed from the plug socket before cleaning the appliance.
• Make sure no moisture gets into the interior of the housing.
• Do not immerse the appliance in water or in other liquids. If this does happen, do not use the appliance again. For safety reasons, dispose of the appliance.

• Only the separate components may be cleaned in a dishwasher.

• Never use corrosive or scouring cleaning products.

• This blender uses sharp knives, which are located in the bottom of the container. Therefore, be very careful when emptying and cleaning the blender. Avoid cutting yourself on the knives.

1 Clean the exterior of the housing with a soft, damp cloth.
2 Clean the jugs and the components with warm soapy water.
3 Thoroughly clean the rotating knives at the bottom of the jug, in particular, and make sure you remove all the food from them (see 'Removing and fixing the base with the rotating knives').
4 Remove the base from the mill (see removing mill base from mill).
5 Clean the mill-jug and the components of the mill with warm soapy water.
6 Thoroughly clean the rotating blades at the bottom of the jug, in particular, and make sure you remove all the food from them.
7 Dry the components thoroughly after they have been cleaned.

Removing and fixing the base with the rotating knives

See figure 3.

1 Fit the jug to the housing.
2 Hold the housing.
3 Rotate the jug anti-clockwise.
4 Remove the jug from the base with the rotating knives.
5 Remove the base with the rotating knives from the housing.
6 Reassemble the base with the rotating knives and the jug in the opposite order.

Removing the mill base from mill

See figure 5.

1 Hold the mil and rotate the mill base anti clockwise.
2 Remove the base from the mill-jug.
3 Reassemble the mill in the opposite order.

Safety

General information

• Please read these instructions carefully and keep them for future reference.
• Only use this appliance in accordance with these instructions.
• Only use this appliance for domestic purposes.
• The use of this appliance by children or persons with a physical, sensory, mental or motor limitation or persons who lack the necessary knowledge and experience may result in a dangerous situation. Persons responsible for their safety must give explicit instructions or supervise the use of the appliance.
• Make sure children do not play with the appliance.
• Repairs may only be carried out by a qualified service technician. Never try to repair the appliance yourself.

Heat and electricity

• Verify that the mains voltage is the same as that indicated on the appliance's type plate before use.
• Plug the appliance into an earthed plug socket.
  Always remove the plug from the plug socket when the appliance is not in use.
• Always remove the plug from the plug socket by pulling the plug, not the power cord.
• Do not use the appliance if the power cord or the appliance is damaged. For your own safety, return the appliance to our service department. A damaged power cord may only be replaced by our service department using the special tools required for the repair.
• Make sure the appliance and the power cord do not come in contact with heat sources, such as a hot hob or a naked flame.

• Make sure the appliance, the power cord and the plug do not come into contact with water.

• Do not pick up the appliance if it falls into water. Remove the plug from the plug socket immediately. Do not use the appliance anymore.

During use

• When using the blender continuously during a longer period, the electric motor will warm up. In this case, let the motor cool down before further use of the appliance.
• Never use the appliance outdoors.
• Never use the appliance in a humid room.
• Place the appliance on a flat, stable surface where it cannot fall.
• Never allow the power cord to hang over the edge of the draining board, worktop or table.
• Make sure your hands are dry when you touch the appliance, the power cord or the plug.
• Only turn on the appliance if a jug has been placed on the housing and a lid has been placed on the jug.
• Switch off the appliance and remove the plug from the plug socket in the event of a malfunction during use and before cleaning the appliance, fitting or removing an accessory, or storing the appliance after use.
• Never leave the appliance unattended when in use.
• After use, clean the appliance thoroughly (see 'Cleaning and maintenance').
• The blender works very quickly. The ingredients are ground within just a few seconds. The longer the blender is turned on, the finer the products will be ground.
• Hot liquids in the blender may result in the lid flying off due to the steam and pressure caused by the hot liquid. Prevent this from happening by holding the lid down with a cloth whilst the blender is in use.

U.K. WIRING INSTRUCTIONS

The wires in the mains lead are coloured in accordance with the following code:

As the colours of the wire in the mains lead of this appliance may not correspond with the colour markings identifying the terminals on your plug, proceed as follows:

• The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured black.
• The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured red.
• The wire which is coloured GREEN/YELLOW must be connected to the terminal which is marked with the letter E or (earth symbol) and is coloured GREEN or GREEN/YELLOW

WARNING: THIS APPLIANCE MUST BE EARTHED

The environment

Dispos of packaging materials, such as plastic and boxes, in the appropriate containers.

If you wish to dispose of the appliance whilst it still works properly or can be easily repaired, ensure that the appliance is recycled.

When the appliance reaches the end of its useful life, it must be disposed of in a responsible manner, thereby ensuring the reuse of the appliance or its parts. Do not dispose of the appliance with normal household waste, but hand it over to a recycling collection point. Contact your local authority for

information about available disposal and collection systems in your area.

Applicable European guidelines:

2002/95/EC
2002/96/EC

Recipes

Browse the internet for delicious recipes to make with a blender. Below you'll find three of the recipes we have found for you.

Banana milkshake

Ingredients:

1 Banana

Vanilla ice

Milk

Cut the banana into slices and put these in the jug of the blender. Add some vanilla ice and some cold milk. Switch on the blender and let it blend for a few seconds. The result is a delicious banana milkshake!

Strawberry breakfast

Ingredients:

2 cups unsweetened whole strawberries
1 1/2 cup milk
1/2 cup plain yogurt
2 env. vanilla flavoured instant breakfast mix
2 tablespoon honey

Put the ingredients in the jug of the blender. Cover, blend until almost smooth, stop the blender and stir if necessary. Pour into 3 or 4 glasses. Serve immediately.

Creamy avocado lime dip

Ingredients:

1 ripe avocado

1 tablespoon freshly squeezed lime juice

1/2 teaspoon hot pepper sauce

1 garlic clove, finely chopped

salt & freshly ground black pepper

Peel, dice and de-pit the avocado and place the remainder in the blender. Add lime juice, hot pepper sauce and garlic.

Process until smooth and then season with salt and pepper.

Transfer to a bowl and cover by placing plastic wrap on top of the avocado mixture. Keep refrigerated until served.

Généralités

2002/95/EOF
2002/96/EOF

Opskrifter

2002/95/EF
2002/96/EF

Oppskrifter

Forsök en gang à lete etter deilige oppskrifter for mikseren pa Internett. Her fár du allerede tre oppskrifter vi har funnet til deg.

Bananmilkshake

Ingredienser:

1 banan

Vaniljeis

Melk

aL aL aL aL aL aL aL aL aL aL aL aL aL aL aL aL aL aL aL aL aL aL aL aL aL aL aL aL aL a L a L a L a L a L a L a L a L a L a L a L a L a L a L a L a L a L a L a L a L a L a L a L a L a L a L a L a L a L a L a L a L a L a L a L a L a L a L a L a L a L a L a L a L a L a L a L a L a L a L a

aai bai aiai bai aai bai aai bai aai bai

aaii aiee iieae iieae iieae iieae iieae iieae iieae iieae iieae iieae iieae iieae iieae iieae iieae iieae iieae iieae iieae iieae iieae iieae iieae iieae iieae iieae iieae iieae iieae iieae iieae iieae iieae iieae

JILW gIgog 1slo pluuiuIglcgaiuuaibiao (P) g21 gao jg 1 sIcUaIgai Jauai I aIi Jauai

aegbui 1o Lel jgl 1j 1s 1s 1s 1s 1s 1s 1s 1s 1s

S木弟形 COBD = S COD + S BDO = S BOC +

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

jLg31 j0 aJgJ1 JSLswJ g0 ocl4 dJlJ Ld1 1sLc9 gJgJ1 JSLswJ ocl4 gO31 OgL

S AOB = S COD + S_ BDO

J 100

1

g j 1111111111111111111111

L 1

Jll Jw Jsc Jc

j 1

L

jLw jLai 8 aIbJI cllw g JgJ

1 1

sU 1

J 1

jg 12 jlgj1 prsrig

aibb1 20 aibb1 acl3 aiji

a < 5 < 3

aaiabll oclal jaiabll

a < L 即

aihali sIcgo 0aclal

111 111 111 111 111 111 111 111

a051

alc CLogLeo

g 15

[ \Leftrightarrow \;{b}{1} = {b}{2} = \cdots = {b}_{n}]

plaiwiw 1

algo jaijai jiei 15 iui 1031 piaiui

jLd1 jJl i 0i jySll jgll

aofiwi 0L1

aagai 511 ySLo21 jLgai piai wae

a,b a jg jglj pssu wpe 8

logzwJl

gai 2gj a1e jhuw jhui Cawie

Jg

g j 11111111111111111111111

L

1c 1531 c1g j5 131 kaa jka jia

13.13.1 sIg Ic Cio 13.21g Jg

jai jia jia jia

a 1

jgl jz jg .Jj g 100

pL

pssss 1 s

gabwglj 10000000000000000000000000000

i: iLwai jLd1 2Lw! Jg8 8. Lgfo aoo

S OBC = S COD + S BOC - S BOC

p1111 1 j1j11

Lolao Joo jolld

S OBC = S COD + S_ BOC