R 224 TC - Pan ZIBRO - Free user manual and instructions

Frequently Asked Questions - R 224 TC ZIBRO

USER MANUAL R 224 TC ZIBRO

Exterior view of a Zibro heat exchanger with cooling fan and control panel (no visible text or symbols)

guarantee

4

YEARS

F	MANUEL d’UTILIsATIoN	2
D	GEBrAUCHsANWEIsUNG	14
DK	BrUGsANVIsNING	26
E	INsTrUCCIoNEs dE Uso	38
FIN	KÄYTTÖoHJE	50
GB	oPErATING MANUAL	62
I	IsTrUZIoNI d’Uso	74
N	BrUKsANVIsNING	86
NL	GEBrUIKsAANWIJZING	98
S	BrUKsANVIsNING	110

PAGE PLIANTE
D AUFFALTBLATT
DK FoLdEUdsIdE
E HoJA dEsPLEGABLE
FIN AUKI TAITETTU sIVU
GB FoLd-oUT PAGE
PIEGHEVoLE
N UTBrETTsIdE
NL UITVoUWBLAd
S UTVIKNINGssIdA

Chère Madame, Cher Monsieur,

LE COMBUSTIBLE APPROPRIÉ

Exploded view diagram of a kitchen appliance showing internal components and directional arrows (no text or labels)

Hand holding a tool with an upward arrow, next to a grid-patterned object (no text or symbols)

Diagram of a mechanical press or pressure testing setup with hands holding a component (no text or symbols visible)

Line drawing of a portable air conditioner unit with a door and vent, showing internal components and a black arrow indicating direction (no text or symbols)

Diagram of a food oven with labeled parts and a label 'E' indicating the component.

F

G

MANUEL

A INSTALLATION DE L'APPAREIL

Illustration of a hand pressing down on a block with an arrow indicating upward motion (no text or symbols)

Line drawing of a gas storage bottle connected to a delivery tube (no text or symbols)

vide plein

Hand holding a circular object with an arrow indicating rotation, no text or symbols present

Hand pointing at a circular object with an arrow labeled 'L' (no text or symbols on the object itself)

F

B REMPLISSAGE DU COMBUSTIBLE

Hand holding a circular object with a curved arrow indicating rotation (no text or symbols)

D FONCTIONNEMENT DE L'APPAREIL

Hand holding a ball with an arrow pointing to the ball, against a horizontal surface and a curved line (no text or symbols)

Line drawing of a hand inserting a small object into a device inside a window (no text or symbols)

Diagram of a hand inserting a cup into a device, showing mechanical components and a downward arrow (no text or symbols)

Bouchon de transport

K CONDITIONS DE GARANTIE

Illustration of a hand using a tool to press or install a device on a tray (no text or symbols visible)

Diagram showing a mechanical or electrical component with polarity markings (+/-) and an identifier '2' in the corner.

Illustration of a hand inserting a component into a cylindrical device (no text or symbols visible)

Illustration of a hand holding a circular device with a gear and directional arrow (no text or symbols)

Hand holding a tool with a circular button, no visible text or symbols

Line drawing of a device rear panel with a button and label '5b' (no text or symbols on the main diagram)

Illustration of a hand holding a portable air purifier with a scroll, showing airflow direction (no text or symbols)

Line drawing of a hand pressing a button on a mechanical component (no text or symbols)

Mechanical assembly diagram showing a presser pressing a component with an arrow indicating motion (no text or symbols present)

8a 15

Technical line drawing of a mechanical device with motion lines and a directional arrow (no text or symbols)

Mechanical assembly diagram showing a rotating component with a curved arrow indicating rotation (no text or symbols)

10 Pin Handle arm

Illustration of a hand holding a curved object with a small inset showing a hand holding the part (no text or symbols present)

LE CHANGEMENT DE LA MÈCHE

L AVANT DE COMMENCER A CHANGER LA MECHE, L'APPAREIL DOIT ÊTRE ETEINT ET TOTALEMENT REFROIDI.

Hand holding a tool with an upward arrow, no visible text or symbols

Diagram of a mechanical press or pressure testing setup with hands holding a component (no text or symbols visible)

Diagram of a device with a left-side arrow indicating direction, no text or symbols present

Diagram of a kitchen appliance with labeled parts and a label 'E' indicating a section.

F

G

Illustration of a hand pressing down on a mechanical component with an arrow indicating upward motion (no text or symbols)

▶ Rauch und/oder Geruch

A DIE INSTALLATION DES kAMINofENS

Exploded view diagram of a microwave oven system with cooling unit and internal components (no text or labels)

Hand holding a circular object with an arrow indicating rotation, no text or symbols present

Hand pointing at a circular dial with an arrow labeled 'L' (no text or symbols on the dial itself)

Hand holding a circular object with an arrow indicating rotation, no text or symbols present

Hand pointing at a surface with a compass needle and a small circle labeled 'N' (no text or symbols on the diagram itself)

E DAS AUSSCHALTEN DES kAMINofENS

DIE fLAMME DES kAMINofENS BRENNT ZU HoCH.

Line drawing of a device interior with a handle and base, no text or symbols present

Diagram of a hand inserting a small object into a device, showing internal components and a downward arrow (no text or symbols)

Transportverschluß

Line drawing of a hand using a tool to press or install a device on a tray (no text or symbols)

Diagram showing a mechanical or electrical component with polarity markings (+/-) and an identifier '2' in the corner.

Illustration of a hand inserting a textured device into a cylindrical component (no text or symbols visible)

Diagram showing hand holding a circular component with a gear-like inset, labeled with Chinese character '国' (country)

Hand holding a tool with a circular knob, no visible text or symbols

Simple line drawing of a mechanical component with a base and mounting bracket (no text or symbols)

Illustration of a portable air purifier with a hand operating it, showing airflow direction (no text or symbols)

Illustration of hands operating a mechanical switch with a knob (no text or symbols)

Mechanical assembly diagram showing a presser pressing a component with a mesh chamber (no text or symbols)

Mechanical assembly diagram showing a hand operating a tool with a spring scale (no text or symbols)

Technical line drawing of a mechanical device with an arrow indicating motion (no text or symbols)

Mechanical assembly diagram showing a rotating component with no visible text or symbols

10 Pin Handle arm

Simple line drawing of a hand holding a curved object with a label '11' (no text or symbols on the diagram itself)

WECHSELN DES DOCHTES

L DER ofEN MUSS GANZ ABGEKÜHLT SEIN, BEVoR SIE MIT DEM DoCHTWECHSEL BEGINNEN.

Illustration of a hand holding a rolled-up sheet of paper or paper, with no visible text or symbols.

12b UP 21 Pin

13a Pin Handle arm

Mechanical assembly diagram showing a rotating component with a handle and housing (no text or symbols)

Diagram of a mechanical device with a hand holding a tool, showing motion and assembly (no text or symbols)

Illustration of a hand using a tool to adjust or install a mechanical component (no text or symbols visible)

Mechanical assembly diagram showing a presser pressing a component with a downward arrow indicating motion (no text or symbols present)

Illustration of a hand holding a small mechanical component, no text or symbols present

17a

Line drawing of a hand holding a car seatbelt with an arrow indicating motion (no text or symbols)

18a

Line drawing of a device component with a button and label '18b' (no readable text or symbols beyond the label)

18c

Line drawing of a portable air purifier with a handle and label '18d' (no text or symbols on the device itself)

19a

19b

HVAD MAN F∅RST SKAL VIDE

S∅RG ALTID FOR TILSTRÆKKELIG VENTILATION

Hand holding a tool with an upward arrow, no visible text or symbols

Illustration of hands operating a mechanical press or press device with arrows indicating movement (no text or symbols present)

Line drawing of a portable air conditioner unit with a cooling fan and directional arrow (no text or symbols)

Diagram of a portable air fryer with labeled parts and a label 'E' indicating the device.

F

G

Illustration of a hand pressing down on a mechanical component with an arrow indicating upward motion (no text or symbols)

Exploded view diagram of a kitchen appliance showing internal components and assembly (no text or labels)

Gem kassen og emballagematerialet (fig. A) til opbevaring eller transport.

Diagram of a water safety device with labeled components and a connected bag, showing internal compartments with 'water' symbols.

Two identical oval electronic components with pins, labeled 'Tom Fuld' below (no additional text or symbols)

Hand holding a knob with a curved arrow indicating rotation (no text or symbols)

Diagram showing a hand pressing a circular dial on a surface with an arrow indicating direction, labeled 'L' in the corner.

F

DK

Hand holding a circular object with an arrow indicating rotation, no text or symbols present

Hand holding a ball near a surface with an arrow and a small circle, no text or symbols present

Line drawing of an air conditioner unit with a vent and fan (no text or symbols)

Diagram of a hand inserting a small object into a container, with an arrow indicating direction (no text or symbols present)

transportprop

TRANSPORT

Line drawing of a mechanical device with an upward arrow indicating motion (no text or symbols)

Diagram showing a mechanical or electrical component with polarity markings (+/-) and an identifier '2' in the corner.

Illustration of a hand inserting a filter into a device (no text or symbols visible)

Diagram showing hand holding a circular device with a gear and directional arrow, labeled with number 4

Hand holding a tool with a circular knob, no visible text or symbols

Line drawing of a device rear panel with a button and label (no readable text or symbols)

Illustration of a hand holding a portable air purifier with a scroll, showing airflow direction (no text or symbols)

Line drawing of a hand pressing a button on a mechanical component (no text or symbols)

Mechanical assembly diagram showing a presser pressing a component with a checkered mesh and directional arrow (no text or symbols)

8a

Technical line drawing of a mechanical device with an arrow indicating motion (no text or symbols)

Mechanical assembly diagram showing a rotating component with a curved arrow indicating rotation (no text or symbols)

10 Pin Handle arm

Illustration of a hand holding a curved object with a small arrow pointing to it, no text or symbols present.

UDSKIFTNING AF VÄGEN

L INDEN Du påBEGyNDER uDSKIFTNINGEN AF VÄGEN, SKAL KAMINEN VÄRE SLuKKET OG HELT AFKÖLET.

Illustration of a hand holding a rolled-up sheet of paper or paper, with no visible text or symbols.

12b UP 21 Pin

13a Pin Handle arm

Mechanical assembly diagram showing a rotating component with a handle and housing (no text or symbols)

Mechanical assembly diagram showing a hand pressing a component with a curved arrow indicating motion (no text or symbols)

Illustration of a hand using a tool to adjust or install a mechanical component (no text or symbols visible)

Mechanical assembly diagram showing a presser pressing a component with a downward arrow indicating motion (no text or symbols present)

Illustration of a hand holding a small mechanical component, no text or symbols present

17a

Line drawing of a hand holding a car seatbelt with an arrow indicating motion (no text or symbols)

18a

Line drawing of a device component with a 18b label and a button, no readable text or symbols present.

18c

Line drawing of a portable air conditioner unit with cooling tower and handle (no text or symbols)

19a

19b

Exploded view diagram of a cleaning machine with labeled components (no text or symbols)

Illustration of a hand pressing down on a mechanical component with an arrow indicating upward motion (no text or symbols)

Diagram of a water tank with labeled components and a gas cylinder, showing internal compartments with recycling symbols.

Hand holding a circular object with an arrow indicating rotation (no text or symbols)

Hand holding a circular dial with an arrow labeled 'L' pointing to it (no text or symbols on the dial itself)

B LLENAR DE COMBUSTIBLE

Hand holding a circular object with an arrow indicating rotation, no text or symbols present

Hand holding a ball with an arrow pointing to it, against a horizontal surface and a curved line above (no text or symbols)

G

Technical diagram showing two steps of a kitchen appliance with labeled parts O and P, including a hand pressing a cup.

Tapón de transporte

Line drawing of a hand using a tool to press or install a device on a tray (no text or symbols)

Diagram showing a mechanical or electrical component with polarity markings (+/-) and an identifier '2' in the corner.

Illustration of a hand inserting a component into a cylindrical device (no text or symbols visible)

Diagram showing hand holding a circular device with a gear and directional arrow, labeled with number 4

Hand holding a tool with a circular button, no visible text or symbols

Line drawing of a device component with a handle and base (no text or symbols)

Illustration of a hand holding a portable air conditioner unit with a scroll, showing airflow direction (no text or symbols)

Line drawing of a hand pressing a button on a mechanical component (no text or symbols)

Mechanical assembly diagram showing a presser pressing a component with a checkered mesh and directional arrow (no text or symbols)

8a

Technical line drawing of a mechanical device with an arrow indicating motion (no text or symbols)

Mechanical assembly diagram showing a rotating component with a curved arrow indicating rotation (no text or symbols)

10 Pin Handle arm

Illustration of a hand holding a coiled object with a tool, no text or symbols present

CAMBIAR LA MECHA

L ANTES DE COMENZAR A CAMBIAR LA MECHA, LA ESTUFA TIENE QUE ESTAR APAgADA Y COMPLETA - MENTE FRÍA.

Illustration of a hand holding a rolled-up sheet of paper or paper, with no visible text or symbols.

12b UP 21 Pin

13a Pin Handle arm

Mechanical assembly diagram showing a rotating component with a handle and housing (no text or symbols)

Mechanical assembly diagram showing a hand pressing a component with a curved arrow indicating motion (no text or symbols)

Illustration of a hand using a tool to adjust or install a mechanical component (no text or symbols visible)

Mechanical assembly diagram showing a presser pressing a component with a downward arrow indicating motion (no text or symbols present)

Illustration of a hand holding a small mechanical component, no text or symbols present

17a

Line drawing of a hand holding a car seatbelt with an arrow indicating motion (no text or symbols)

18a

Line drawing of a device component with a 18lb mark and a button, no text or symbols present

18c

Illustration of a cylindrical device with a mesh grille and a handle, no visible text or symbols

19a

19b

Hand holding a tool with an upward arrow, no visible text or symbols

Diagram of a mechanical press or pressure testing setup with hands holding a component (no text or symbols visible)

Diagram of a microwave oven with a door and vent, showing internal components and an arrow indicating direction (no text or symbols)

Diagram of a portable air purifier with labeled parts and component E

F

G

Diagram showing a hand pressing down on a device labeled 'H' with an upward arrow, likely illustrating a process or operation.

Technical diagram of a blender with labeled components and directional arrows indicating assembly or operation.

Diagram of a water tank with labeled components and a connected device, showing recycling symbols and a valve mechanism.

Two identical electrical connector pinouts with terminal symbols, labeled 'leeg vol' below (no additional text or symbols)

Hand holding a knob with a curved arrow indicating rotation (no text or symbols)

Hand holding a circular dial with an arrow pointing to it, against a plain background (no text or symbols)

Illustration of a hand holding a circular object inside a cage-like structure, with arrows indicating direction (no text or symbols)

Hand holding a circular object with an arrow indicating rotation, no text or symbols present

D LÄMMITTIMEN POLTTAMINEN

Hand holding a ball with an arrow pointing to it, against a background with a north arrow and bubbles (no text or symbols)

G

EPÄSÄÄNNÖLLINEN LIEKKI JA/TAI NOKI JA/TAI HAJU

Two-panel diagram showing a hand inserting a small plant into a container, labeled O and P (no text or symbols on the diagrams themselves)

kuljetuskorkki

I KULJETUS

Line drawing of a mechanical device with an upward arrow indicating motion (no text or symbols)

Diagram showing a battery with polarity labels (+/-) and negative charges, likely illustrating electrochemical or electrochemical process.

Illustration of a hand inserting a component into a cylindrical device (no text or symbols visible)

Diagram showing hand holding a circular device with a gear and directional arrow, labeled with number 4

Line drawing of a hand turning a valve on a car surface (no text or symbols)

Line drawing of a device rear panel with a button and label (no readable text or symbols)

Illustration of a hand holding a portable air conditioner unit with a scroll, showing airflow direction (no text or symbols)

Line drawing of a hand pressing a button on a mechanical component (no text or symbols)

Mechanical assembly diagram showing a presser pressing a component with a checkered base (no text or symbols visible)

8a

Technical line drawing of a mechanical device with an arrow indicating motion (no text or symbols)

Mechanical assembly diagram showing a rotating component with a curved arrow indicating rotation (no text or symbols)

10 Pin Handle arm

Illustration of a hand holding a curved object with a tool, no text or symbols present

SYDÄMEN VAIHTAMINEN

VARMISTA, ETTÄ LÄMMITIN ON SAMMUTETTU JA TÄYSIN JÄÄHTYNYT, ENNEN KUIN ALOITAT SYDÄMEN VAIHTAMISEN.

Illustration of a hand holding a rolled-up sheet of paper or paper, with no visible text or symbols.

12b UP 21 Pin

13a Pin Handle arm

Mechanical assembly diagram showing a rotating component with a handle and housing (no text or symbols)

Mechanical assembly diagram showing a hand pressing a component with an arrow indicating motion (no text or symbols)

Illustration of a hand using a tool to adjust or install a mechanical component (no text or symbols visible)

Mechanical assembly diagram showing a presser pressing a component with a downward arrow indicating motion (no text or symbols present)

Illustration of a hand holding a small mechanical component, no text or symbols present

17a

Line drawing of a hand holding a tool with an arrow indicating direction (no text or symbols)

18a

Line drawing of a device component with a 18lb mark and a button, no text or symbols present

18c

Line drawing of a portable air conditioner unit with cooling fan and handle (no text or symbols)

19a

19b

Congratulations with your purchase of the Zibro, the number one brand among movable heaters. You have purchased a first-class quality product, which will serve you for many years to come. This, of course, provided you use the heater correctly. Please read these Directions for Use first, to ensure maximum lifetime for your Zibro.

Your heater comes with a 48-month manufacturer's warranty on all defects in material or workmanship.

We wish you much warmth and comfort with your Zibro.

Yours sincerely,

PVG Holding b.v.

Customer Service Department

1 READ THE DIRECTIONS FOR USE FIRST.

2 IN CASE OF ANY DOUBT, CONTACT YOUR DEALER.

3 BEFORE YOU START READING, FOLD OUT THE LAST PAGE. ▶▶▶▶▶▶▶▶▶▶

GENERAL DIRECTIONS FOR USE

Below you will find the main steps to be taken for using your heater. For more details, please refer to the MANUAL (pages 53 ff.).

1 Remove all packaging materials (refer to Section A, Fig. A).
2 Fill the removable tank ⑨ and wait 30 minutes before you ignite the heater (refer to Section B, Fig. 1).
3 Insert the batteries into the battery holder ⑫ (refer to Section A, Fig. G).
4 Check whether the combustion chamber ④ is fully upright (refer to Section A, Fig. F).
5 Ignite the heater by turning the knurled wick adjustment knob ② as far to the right as possible and then gently push the ignition button ③ (refer to Section C, Fig. K and L).
6 After igniting the heater it will take 10 to 15 minutes before you can check if the heater burns well (refer to Section D).
7 Switch off the heater (refer to Section E).

- The first time you ignite your heater it will smell like 'new' for a short time.

- Store your fuel in a cool and dark place.

- Fuel has a limited shelf life. Start every heating season with new fuel.

- The right quality of fuel will be assured, when you use Zibro Premium Quality Fuels for your heater.

- If you change to another brand and/or type of paraffin oil, you must first finish up all the remaining fuel in the heater.

- Avoid any contact with the top plate and grille.

MAIN COMPONENTS

① OFF - button
② Knurled wick adjustment knob
③ Ignition button
4 Combustion chamber
⑤ Combustion chamber handle
6 Fuel indicator
7 Grill
⑧ Lid for removable tank
9 Removable tank
10 Fuel gauge removable tank
⑪ Ignition coil
12 Battery holder

WHAT YOU NEED TO KNOW IN ADVANCE

ALWAYS MAKE SURE THAT THERE IS SUFFICIENT VENTILATION

Read this user manual carefully before using the appliance and keep it for future reference. Install this device only when it complies with local/national legislation, ordinances and standards. This product is intended to be used as a heater in residential houses and is only suitable for use in dry locations, in normal household conditions, indoors in living room, kitchen and garage.

For comfortable and safe heating ensure that there is sufficient ventilation.

Note: To avoid unexpected shut off, we recommend to put a door or window ajar when the heater is operating.

For each model the minimum size of space is specified in which you can use the heater safely, without additional ventilation (refer to Section J). If a particular room is smaller than the specified space, always leave a window or door slightly ajar ( ± 2.5 cm). We also recommend doing this in highly insulated or draught-free rooms and/or at altitudes above 1,500 metres. Do not use your heater in cellars or other underground areas.

No modifications to the safety system are allowed, as that will invalidate the guarantee that the air probe will work properly. Consult your dealer in case of doubt.

Only the use of the correct fuel will ensure safe, efficient, and comfortable use of your heater.

SAFE TOP

The heater is supplied with a safe top. This application decreases the temperature of the top plate. In this way, the risk of harmful accidents at accidentally touching the top plate is considerably decreased. However, be aware that the top plate still becomes hot.

Avoid any contact with the top plate and grille.

ESPECIALLY FOR FRANCE: Your heater was designed to operate exclusively on fuel for liquid fuel-operated mobile heaters in accordance with the Decrees of 18-07-2002 and 25-06-2010. The use of other fuels is forbidden. Ask your dealer or check our website for the addresses of our retailers. The liquid fuel-operated mobile heater is intended as an extra heater, and not as a continuous source of heat.

ESPECIALLY FOR UNITED KINGDOM: Only use Class C1 paraffin fuel in accordance with BS2869; Part 2, or equivalent.

SINCE 1983 PREMIUM QUALITY FUELS ACTIVE PROTECTION FORMULA

The user must comply with the following instructions for proper use: DO NOT

• use the liquid fuel-operated mobile heater in caravans, boats, and vehicle cabins;
• use the liquid fuel-operated mobile heater in insufficiently ventilated rooms (consult the table of properties for the minimum dimensions of the room to be heated), underground rooms and / or at a height of over 1500 metres;
• modify the heater safety features.

The use of this type of heating in public rooms is subject to prior regulatory permission. Obtain proper information on this in advance.

This transportation cap is packed separately in the box. Only this cap ensures trouble-free transportation of the heater after use. Store it well!

THE RIGHT FUEL

Only use Class C1 paraffin fuel in accordance with BS2869 Part two, or equivalent. Your heater has been designed for use with high-quality water-free pure paraffin oil, such as Zibro Premium Quality Fuels. Only fuels of this kind will ensure clean and proper burning. Lower quality fuel may result in:

▶ excessive tar deposits on the glass fibre wick
▶ incomplete burning
▶ reduced heater lifetime
▶ smoke and/or smells
▶ deposits on the grid or mantle

Using the right fuel is therefore essential for safe, efficient, and comfortable use of your heater.

Damage and/or malfunctions of the heater due to the use of other than high quality water-free pure paraffin oil is not covered by the warranty.

Always refer to your local Zibro dealer for the right fuel for your heater.

MANUAL

A INSTALLING THE HEATER

1 Carefully remove your heater from the box and check the contents. In addition to the heater you also need to have:

▶ a transportation cap
▶ these directions for use
▶ a manual fuel pump

Exploded view diagram of a blender with internal components and directional arrows indicating assembly (no text or labels)

Keep the box and the packaging materials (Fig. A) for storage and/or transportation.

2 Remove the other packaging materials:

▶ Release the right side of the grill ⑦ from the two slots by pulling the right side of the grill to the left and then pull it forward (Fig. B).
▶ Pull both ends of the packaging to the rear and at the same time slightly downwards (see Fig. C).
▶ Remove the combustion chamber ④ from the heater and remove the packaging underneath (see Fig. D).
▶ Put the combustion chamber back into its place. The combustion chamber is positioned correctly when it can be smoothly moved a little to the left and to the right by its handle ⑤ (Fig. F). Close the grill: Slightly lift it to reposition it in its slot.
▶ Open the lid of the removable tank ⑧ and remove the piece of cardboard.

If the left side of the grill has been removed, first insert the flattened upper left end of the grill into the upper left slot and then insert the other flattened end into the lower left slot (Fig. E).

3 Fill the removable tank as indicated in Section B.
4 Insert the batteries into their holder ⑫ at the back of the heater (Fig. G). Ensure that the positive and negative poles match the + and - marks indicated on the battery housing. It is best to use new alkaline batteries (2x D-size).
5 The floor should be firm and completely level. Reposition the heater, when it is not level. Do not correct the situation by placing books or other goods under the heater.
6 Your heater is now ready for use.

B FILLING FUEL

Do not fill the removable tank in the living room, but in a more suitable place (there can always be some spillage). Follow the procedure below:

Illustration of a hand pressing down on a mechanical component with an arrow indicating upward motion (no text or symbols)

Diagram of a water tank with labeled components and a gas bag, showing recycling symbols and piping connections.

Two identical oval-shaped electronic connectors with pin headers, labeled 'empty full' below (no text on connectors)

Hand holding a knob with a curved arrow indicating rotation (no text or symbols)

Hand pointing at a circular dial with an arrow indicating direction (no text or symbols)

GB

1 Make sure that the heater is switched off.
2 Open the lid ⑧ and lift the removable tank ⑨ out of the heater (Fig. H). Note: Some drops may leak from the tank. Put down the removable tank (cap pointing upwards) and screw off the fuel cap.
3 Take the manual fuel pump and insert the smooth, most rigid tube into the jerrycan. Make sure that it is in a higher position than the removable tank (Fig. I). Insert the ribbed hose into the opening of the removable tank.
4 Lock the valve on top of the pump (turn clockwise).
5 Squeeze the pump a few times, until fuel starts flowing into the removable tank. As soon as this happens, there is no need to press any longer.
6 Check the removable tank fuel gauge 10 while filling the tank (Fig. J). Stop filling by loosening the valve on top of the pump (turn anti-clock-wise), once the gauge indicates that the tank is full. Never overfill the tank, especially not when the fuel is very cold (fuel expands when it heats up).
7 Let the remaining fuel in the pump flow back into the jerrycan and carefully remove the pump. Carefully screw the fuel cap back on the tank. Clean off any spilled fuel.
8 Check whether the fuel cap is straight and tightened properly. Reinstall the removable tank in the heater (cap down). Close the lid.

C IGNITING THE HEATER

A new heater may give off some smells for a short while, when it is used for the first time. You should therefore provide extra ventilation or ignite the heater outside the living room.

When you use the heater for the first time, first put the filled removable tank into place, and then wait approximately 30 minutes before you ignite the heater. This allows the glass fibre wick to soak up the fuel. Follow the same procedure when you have completely burnt up all fuel from the tank, and after the glass fibre wick has been replaced.

Before igniting the heater, always check the fuel indicator ⑥ to see whether the removable tank needs filling up.

Always ignite the heater with the ignition coil ⑪. Never use matches or a cigarette lighter.

Follow the procedure below:

1 Turn the knurled wick adjustment knob ② clockwise to its stop (Fig. K). If you apply more pressure you may turn it slightly further; however, it will automatically return to the startposition.
2 Push in the ignition button ③ (Fig. L), but do not apply too much force.

F

Release the ignition button as soon as a flame is visible in the combustion chamber 4.

When you have ignited the heater and it shuts off again shortly after, the batteries need to be replaced. It is best to use new alkaline batteries (2x D-size).

If the heater has been used only a few times and the wick adjustment knob is not locked, first turn the wick adjustment knob (Fig. M) completely left, before putting the wick in the highest position for ignition (Section C).

Hand holding a circular object with an arrow indicating rotation, no text or symbols present

After having ignited the heater, always check whether the combustion chamber ④ is level, by sliding it slightly to the left and the right by its handle ⑤ (Fig. F). This should be a smooth movement. If the combustion chamber is not level, this will cause smoke and soot to develop.

d BURNING OF THE HEATER

After you have ignited the heater, it will take 10 to 15 minutes before you can check whether the heater is burning well. Too high a flame may cause smoke and soot, whereas too low a flame causes smells. The page opposite the folding page shows the minimum and maximum permissible burning heights of the flame (Fig. Q). The flame can be slightly adjusted with the knurled wick adjustment knob ② (Fig. M).

Burning that is too low may be caused by:

▶ insufficient fuel (fill the tank)
▶ poor fuel quality (contact your dealer)
▶ insufficient ventilation (put window or door ajar)
▶ wastage of the wick (contact your dealer or replace the wick, refer to section L)

When there is insufficient ventilation in the room, the heater shuts off automatically. After improving the ventilation of the room (e.g. by opening a door or window a little more), the heater can be ignited again.

Hand holding a ball with an arrow pointing upward, against a horizontal surface and a circular object (no text or symbols)

This heater is equipped with a safety mechanism which switches off the heater when the removable fuel tank is taken out of its compartment. To re-ignite the heater, place the removable fuel tank back in the heater and follow the instructions as described in chapter C.

G

E SWITCHING OFF THE HEATER

Push the OFF-button ①. The flame will extinguish after a little while (Fig. N).

F MALFUNCTION, CAUSES AND SOLUTIONS

If any malfunctioning cannot be solved from the directions below, please contact your dealer.

THE HEATER DOES NOT IGNITE

▶ The batteries are not positioned correctly in the holder.
Check (Fig. G).
▶ There is not enough power left in the batteries for the ignition.
Replace (Fig. G).

▶ You have run out of fuel from the tank or the wick has been replaced.

After having refilled and replaced the removable tank, wait for 30 minutes before igniting the heater.

▶ You are pushing the ignition button ⓣ with too much force. Push it in less forcefully (Section C).
▶ The ignition coil ⑪ is defective. Contact your dealer.

IRREGULAR FLAME AND/OR SOOT AND/OR SMELLS

▶ The combustion chamber ④ has not been positioned correctly.

Use the handle ⑤ to put it level, until you can easily slide it slightly to the left and to the right and the chamber is level.

▶ You are using fuel which is past its 'use by' date.

Start every heating season with fresh fuel.

▶ You are using the incorrect type of fuel.

Refer to THE RIGHT FUEL (See Section 'What you need to know in advance').

▶ Dust has gathered in the lower part of the heater.

Contact your dealer.

▶ The wick height is not correct.

Contact your dealer.

THE HEATER SLOWLY EXTINGUISHES

▶ The removable tank is empty.

See Section B.

▶ The lower reservoir is contaminated by moist.

Contact your dealer.

▶ The wick has hardened on the upper side.

Burn the heater until all fuel is used (Section G). Use the right fuel.

▶ You are using fuel which is past its 'use by' date.

Start every heating season with fresh fuel.

THE HEATER REMAINS BURNING LOW

▶ Wick position too low.

Contact your dealer.

▶ Before you refilled the tank, the heater had burnt up almost all the fuel.

After having refilled and replaced the removable tank, wait for 30 minutes before igniting the heater.

▶ You are using the incorrect type of fuel.

Refer to THE RIGHT FUEL (See Section 'What you need to know in advance').

▶ The room is insufficiently ventilated.

Leave a window or a door wide open for a while.

THE HEATER IS BURNING TOO HIGH

▶ You are using an incorrect, too volatile type of fuel.

Refer to THE RIGHT FUEL (See Section 'What you need to know in advance').

▶ Wick position too high.

Contact your dealer.

G MAINTENANCE

Your heater needs hardly any maintenance. It is, however, important that you remove dust and stains in time with a damp cloth, because otherwise these

broken ignition coil

may cause stains that are hard to remove. Under normal conditions, only three components are subject to wear:

1. THE BATTERIES

You may replace the batteries yourself. Do not dispose of old batteries along with the other domestic waste. Follow the locally applicable regulations regarding the disposal of domestic chemical waste.

2. THE IGNITION COIL

The ignition coil will have a longer life, if you ignite the heater in the correct manner. Replace the batteries in time and take care not to push in the ignition button with too much force. If the filament is broken, the ignition coil must be replaced.

3. THE WICK

To extend the glass fibre wick life, you must occasionally let the heater burn until the tank is completely emptied and the heater extinguishes by itself. Do this when you notice that the flame is weakening. The burn-out will cause some smells, so it is recommended that you take the heater outside of the living room.

Do not remove any heater components yourself. Always contact your dealer for repairs.

Let the heater cool down first, before you start any maintenance or service work.

H STORAGE (ENd OF THE HEATING SEASON)

We recommend that you burn up all the fuel in the fuel tank at the end of the heating season and store the heater properly. Follow the procedure on the next page:

1 Ignite the heater outside the living room and let it burn until all fuel is used.
2 Let the heater cool down.
3 Clean the heater with a damp cloth and then dry it with a dry cloth.
4 Remove the batteries from the holder ⑫ and store them in a dry place.
5 Clean the fuel filter (refer to section G).
6 Store the heater in a dust-free place, if possible in its original packaging. Unused fuel cannot be used for the next heating season. If there is still some fuel left, do not throw it away, but dispose of it in accordance with the local regulations for the disposal of domestic chemical waste. Always start the new heating season with fresh fuel. When you start re-using the heater, follow the instructions again (starting from Section A and as specified).

Line drawing of a device interior with a handle and base, no text or symbols present

Diagram of a hand pressing down on a mechanical device with a downward arrow indicating force or movement (no text or symbols present)

Transportation cap

GB

TRANSPORTATION

Take the following measures to avoid fuel leakage during the transportation of the heater:

1 Let the heater cool down.
2 Remove the removable tank ⑨ from the heater and remove the fuel filter (Fig. O). Some drops may leak from the filter; keep a cloth at hand. Store the fuel filter and the removable tank outside the heater.
3 Place the transportation cap into the position of the fuel filter (Fig. P). Press it tight.
4 Always move the heater in an upright position.

J SPECIFICATIONS

Ignition electrical Dimensions (mm) width 428
Fuel paraffin		(including base plate) depth	295
Capacity (kW)*	2.40		height 453
Suitable space (m3)**	40-85	Accessories:	transportation cap manual fuel pump
Fuel consumption (l/hr)*	0.250	Required batteries	2x LR20, MN 1300
Fuel consumption (g/hr)*	200		1.5V, size D
Burning time per tank (hr)*	16	Wick type	F
Capacity removable tank (litres)	4.0
Weight (kg)	7.5

* At maximum setting
** Specified values are indicative

K WARRANTY PROVISIONS

Your heater comes with a 48-month warranty starting on the date of purchase. Within this period all defects in material or workmanship will be repaired without any charge. The following provisions shall apply regarding this warranty:

1 We expressly dismiss all other claims for damages, including consequential damages.
2 Any repairs or replacements of components within the term of warranty will not result in an extension of the term of warranty.
3 The warranty will no longer apply, when the heater has been modified, non-original parts have been used, or when it is repaired by third parties.
4 The warranty will not apply to parts that are subject to normal wear, such as the batteries, the ignition coil, the wick and the manual fuel pump.
5 The warranty will only apply, when you present the original, dated proof of purchase, provided no changes have been made to it.

6 The warranty will not apply to damages caused by actions not in compliance with the Directions for Use, neglect, and the use of an incorrect type of fuel, or fuel past its use-by date. The use of incorrect fuel can even be dangerous*.
7 Transportation costs and the risks involved during the transportation of the heater or heater components will always be the responsibility of the purchaser.

In order to avoid unnecessary costs, we recommend that you always read the 'Directions for Use' carefully first. In case they offer no solution, please take the heater to your dealer for repair.

* Highly inflammable substances may induce uncontrollable burning, causing flames to break out. Should this happen, never try to move the heater, but always switch off the heater immediately (refer to Section E). In cases of emergency you may use a fire extinguisher, but only a type B extinguisher: a carbon dioxide or powder extinguisher.

14 TIPS FOR SAFE USE

100 cm 50 cm 20 cm 50 cm 150 cm

1 Children should be supervised to ensure that they do not play with the appliance.
2 Do not move the heater when it is burning or still hot. Do not refill nor service the heater when it is burning or still hot.
3 Position the front of the heater at a distance of minimum 1.5 metres from walls, curtains, and furniture.
4 Do not use the heater in dusty rooms. You will not have optimum burning in such rooms. Do not use the heater in the immediate surrounding of a bath, a shower or a swimmingpool.
5 Switch off the heater, before you leave or go sleeping. Unplug the heater as well, when you go away for a longer period of time (e.g. holidays).

6 Store and move fuel only in suitable tanks and jerrycans.

7 Make sure that the fuel is not exposed to heat or extreme temperature changes. Always store the fuel in a cool, dry and dark place (sunlight will affect the quality).
8 Never use the heater in places where harmful gasses or fumes may be present (e.g. exhaust gasses or paint fumes).
9 Beware that the grid of the heater becomes hot. If the appliance is covered there is a risk of fire.
10 Always make sure that there is sufficient ventilation.
11 This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
12 This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
13 Children shall not play with the appliance.
14 Cleaning and user maintenance shall not be made by children without supervision.

Line drawing of a hand using a tool to press or install a device on a tray (no text or symbols)

Diagram showing a mechanical or electrical component with polarity markings (+/-) and an identifier '2' in the corner.

Illustration of a hand pressing down on a mechanical component with no visible text or symbols

Diagram showing hand holding a circular device with a gear and directional arrow, labeled with number 4

Hand holding a tool with a circular button, no visible text or symbols

Line drawing of a device rear panel with a button and label (no readable text or symbols)

Illustration of a hand holding a portable air purifier with a scroll, showing airflow direction (no text or symbols)

Line drawing of a hand pressing down on a mechanical component (no text or symbols)

Mechanical assembly diagram showing a presser pressing a component with a valve (no text or symbols visible)

8a

Technical line drawing of a mechanical device with an arrow indicating motion (no text or symbols)

Mechanical assembly diagram showing a rotating component with a curved arrow indicating rotation (no text or symbols)

10 Pin Handle arm

Illustration of a hand holding a coiled object with a tool, no text or symbols present

REPLACEMENT OF THE WICK

L ENSURE THAT THE HEATER IS OFF AND COMPLETELY COOL BEFORE STARTING TO REPLACE THE WICK.

1 Open the lid and remove the removable tank.
2 Remove the batteries from the battery holder.
3 Open the front grill. Remove the combustion chamber from the heater. Close the grill.
4 Pull the knurled wick adjustment knob off the heater.
5 Unscrew the three cabinet screws on the back and sides of the heater. Pull the cabinet forward slightly, and then remove it from the base plate.
6 Unscrew the four wing nuts from the wick holder.
7 Lift the wick holder chassis up until the wick is visible. Place the burner bed next to the heater. (Ensure that the wiring does not become disconnected).
8 Remove the screw on the stem holding the bracket and remove the bracket.
9 Turn right the stem to the end and remove the wick sleeve (with wick).
10 Turn the wick sleeve counterclockwise and lift the wick sleeve up. Remove it from the primary air tube.
11 Squeeze the wick to loosen the three wick pins and remove the wick from the wick sleeve. Ensure that you are wearing gloves and that you have a container in which to put the old wick.

Illustration of a hand holding a rolled-up sheet of paper or paper, with no visible text or symbols.

12b UP 21 Pin

13a Pin Handle arm

Mechanical assembly diagram showing a rotating component with a handle and housing (no text or symbols)

Diagram of a mechanical device with a hand pointing to a component (no text or symbols visible)

Illustration of a hand using a tool to adjust or install a mechanical component (no text or symbols visible)

Mechanical assembly diagram showing a presser pressing a component with a downward arrow indicating motion (no text or symbols present)

Illustration of a hand holding a small object with motion lines, no text or symbols present

17a

Line drawing of a hand holding a mechanical component with an arrow indicating direction (no text or symbols)

18a

Line drawing of a device component with a button and label '18b' (no readable text or symbols beyond the label)

18c

Line drawing of a portable air conditioner unit with cooling fan and handle (no text or symbols)

19a

19b

12 Install the wick to the wick sleeve according to the allowed direction engraved on the wick sleeve.
13 Install the wick sleeve (with wick) to the primary air tube. And then turn the wick sleeve clockwise to set in the handle arm.
14 Install the bracket. Then tighten the screw which is holding the stem.
15 Put the wick holder chassis back into position.
16 Screw the four wing nuts hand tight.
17 Place the knurled wick adjustment knob on the wick mechanism. Turn the knob as far to the right as possible. Press the tip-over switch. Check that the wick can be lowered completely. Repeat this check a number of times. If the wick cannot be lowered completely it has not been placed correctly. If this is the case, repeat the procedure from No. 12. Pull the knurled wick adjustment knob off the heater.
18 Put the cabinet back into position and tighten the three screws. Put the knurled wick adjustment knob back into position. Now put the combustion chamber back into position. Check that it is level by sliding it slightly to the left and the right by its handle. Close the grill.
19 Put the filled removable tank into position. Put the batteries into the battery holder (ensure that the positive and negative poles match the + and - marks indicated on the battery housing). Wait 30 minutes after replacing the tank and batteries before using the heater.

Egregio Signore, Gentile Signora,

Hand holding a tool with an upward arrow, next to a grid-patterned object (no text or symbols visible)

Diagram of hands operating a mechanical press or press device with a perforated base and directional arrows (no text or symbols)

Diagram of a portable air purifier with a door and vent, showing internal components and airflow direction (no text or symbols)

Diagram of a kitchen appliance with labeled parts, showing numbered parts and a label 'E' in the corner.

Diagram showing a hand holding a test tube with arrows indicating force application, labeled 'F' in the corner.

G

Illustration of a hand pressing down on a block with an arrow indicating upward motion (no text or symbols)

Diagram showing a hand pressing down on a device labeled 'H' with an upward arrow, likely illustrating a process or operation.

Exploded view diagram of a kitchen appliance showing internal components and assembly (no text or labels)

Diagram of a water safety device with labeled components including 'water@' and 'water@'

Hand holding a knob with a circular dial, no text or symbols visible

Hand holding a circular dial with an arrow pointing to it, against a plain background (no text or symbols)

B RIFORNIMENTO DEL COMBUSTIBILE

C ACCENSIONE DELLA STUFA

Hand holding a circular object with an arrow indicating rotation, no text or symbols present

D LA COMBUSTIONE DELLA STUFA

Hand holding a ball with an arrow pointing to it, against a horizontal surface and a circular object (no text or symbols)

G

2. LA RESISTENZA DI ACCENSIONE

Diagram of a mechanical device with a container and directional arrow, no visible text or symbols

Diagram of a hand inserting a light bulb into a device component, with an arrow indicating the direction (no text or symbols present)

Line drawing of a hand using a tool to press or install a device on a tray (no text or symbols)

Diagram showing a mechanical or electrical component with polarity markings (+/-) and an identifier '2' in the corner.

Illustration of a hand pressing down on a mechanical component with no visible text or symbols

Diagram showing a hand holding a circular device with a gear and a labeled component, indicating rotation or adjustment.

Hand holding a tool with a circular knob, no visible text or symbols

Line drawing of a device rear panel with a button and label (no readable text or symbols)

Illustration of a portable air purifier with a hand holding the lid and a scroll, showing airflow direction (no text or symbols)

Line drawing of a hand pressing a button on a mechanical component (no text or symbols)

Mechanical assembly diagram showing a presser pressing a component with a checkmark and directional arrow (no text or symbols)

8a

Technical line drawing of a mechanical device with an arrow indicating motion (no text or symbols)

Mechanical assembly diagram showing a rotating component with a curved arrow indicating rotation (no text or symbols)

10 Pin Handle arm

Illustration of a hand holding a curved object with a tool, no text or symbols present

Hand holding a tool with an upward arrow, no visible text or symbols

Diagram of hands operating a mechanical press or press device with a perforated base and directional arrows (no text or symbols)

Diagram of a microwave oven with a door and vent, showing internal components and an arrow indicating direction (no text or symbols)

Diagram of a portable air purifier with labeled parts and component E

F

G

Diagram showing a hand pressing down on a device labeled 'H' with an upward arrow, likely illustrating a process or operation.

Diagram of a water pump system with labeled components and connections

leeg vol

Hand holding a knob with a curved arrow indicating rotation (no text or symbols)

Tenn alltid varmeovnen med tennspolen. Du må aldri bruke fyrstikker eller en sigarett.

Følg fremgangsmåten nedenfor:

1 Drei den riflede vekereguleringsbryteren ② med urviseren til den stopper (fig. K). Hvis du trykker hardere, kan du dreie den litt til, men den går automatisk tilbake til startposisjon.

Hand holding a circular dial with an arrow pointing to it, against a plain background (no text or symbols)

Illustration of a hand operating a birdcage with a circular grid structure and directional arrows (no text or symbols)

Hand holding a circular object with an arrow indicating rotation, no text or symbols present

Hand holding a ball above a surface with two bubbles and an arrow indicating motion (no text or symbols)

G

D SLIK SKAL VARMEOVNEN BRENNE

Diagram showing two steps of a hand pouring liquid into a container, labeled O and P, with arrows indicating flow direction.

Transportdeksel

H OPPBEVARING (SLUTT PÅ DEN KALDE ÅRSTIDEN)

Line drawing of a hand using a tool to press or install a device on a tray (no text or symbols)

Diagram showing a mechanical or electrical component with polarity markings (+/-) and an identifier '2' in the corner.

Illustration of a hand inserting a component into a cylindrical device (no text or symbols visible)

Diagram showing hand turning a gear with label '13' and directional arrow, likely illustrating a mechanical or electrical component.

Hand holding a tool with a circular button, no visible text or symbols

Line drawing of a device component with a handle and base (no text or symbols)

Illustration of a hand holding a portable air purifier with a scroll, showing airflow direction (no text or symbols)

Line drawing of a hand pressing a button on a mechanical component (no text or symbols)

Mechanical assembly diagram showing a presser pressing a component with a valve and housing (no text or symbols)

8a 15

Technical line drawing of a mechanical device with an arrow indicating motion (no text or symbols)

Mechanical assembly diagram showing a rotating component with a curved arrow indicating rotation (no text or symbols)

10 Pin Handle arm

Illustration of a hand holding a curved object with a tool, no text or symbols present

SKIFTE UT VEKEN

L PASS PÅ AT OVNEN ER AV OG HELT KALD F∅R DU BEGYNNER Å BYTTE VEKEN.

Illustration of a hand holding a rolled-up sheet of paper or paper, with no visible text or symbols.

12b UP 21 Pin

13a Pin Handle arm

Mechanical assembly diagram showing a rotating component with a handle and housing (no text or symbols)

Mechanical assembly diagram showing a hand pressing a component with an arrow indicating motion (no text or symbols present)

Illustration of a hand using a tool to adjust or install a mechanical component (no text or symbols visible)

Mechanical assembly diagram showing a presser pressing a component with a downward arrow indicating motion (no text or symbols present)

Illustration of a hand holding a small object with a circular arrow, no text or symbols present

17a

Line drawing of a hand holding a tool with an arrow indicating direction (no text or symbols)

18a

Line drawing of a device component with a button and label '18b' (no readable text or symbols beyond the label)

18c

Line drawing of a portable air conditioner unit with cooling fan and handle (no text or symbols)

19a

19b

WAT U VOORAF MOET WETEN

ALTIJD VOLDOENDE VENTILEREN

Hand holding a tool with an upward arrow, pointing to a vertical structure (no text or symbols visible)

Diagram of a mechanical press or clamping device with hands holding a component, no visible text or symbols

Line drawing of a portable air purifier with a door and vent, showing internal components and airflow direction (no text or symbols)

Diagram of a food oven with labeled parts and air filter, showing internal components and airflow path

F

G

Exploded view diagram of a kitchen appliance showing internal components and directional arrows (no text or labels)

Illustration of a hand inserting a component into a machine, with an arrow indicating direction (no text or symbols present)

Diagram of a water tank with labeled components and a gas bag, showing recycling symbols and connections.

Two identical oval electronic connectors with pin headers, labeled 'leeg vol' below (no additional text or symbols)

Hand holding a circular object with an arrow indicating rotation (no text or symbols)

Hand holding a circular dial with an arrow pointing to it, no text or symbols present

Illustration of a hand holding a cage-like object with arrows indicating movement or force (no text or symbols present)

Hand holding a circular object with an arrow indicating rotation, no text or symbols present

D HET BRANDEN VAN DE KAcHEL

Hand holding a ball above a surface with bubbles and an arrow indicating direction (no text or symbols)

Diagram of a hand inserting a small object into a container inside an air conditioner unit (no text or symbols)

Diagram of a hand inserting a small object into a container, with an arrow indicating direction (no text or symbols present)

Transportdop

VERVOER

Line drawing of a hand using a tool to press or install a device on a tray (no text or symbols)

Diagram showing a mechanical or electrical component with polarity markings (+/-) and an identifier '2' in the corner.

Illustration of a hand pressing down on a mechanical component with no visible text or symbols

Diagram showing hand holding a circular device with a gear and directional arrow, labeled with number 4

Hand holding a tool with a circular knob, no visible text or symbols

Line drawing of a device rear panel with a button and label (no readable text or symbols)

Illustration of a portable air purifier with a hand holding the lid and a scroll, showing airflow direction (no text or symbols)

Line drawing of a hand pressing a button on a mechanical component (no text or symbols)

Mechanical assembly diagram showing a presser pressing a component with a valve and housing (no text or symbols visible)

8a

Technical line drawing of a mechanical device with an arrow indicating motion (no text or symbols)

Mechanical assembly diagram showing a rotating component with a curved arrow indicating rotation (no text or symbols)

10 Pin Handle arm

Illustration of a hand holding a curved object with a small arrow pointing to it (no text or symbols present)

HET VERVANGEN VAN DE KOUS

L VOORDAT U BEGINT MET HET VERVANGEN VAN DE KOUs, DIENT DE KAcHEL UIT EN VOLLEDIG AfGEKOELD TE ZIJN.

Illustration of a hand holding a rolled-up sheet of paper or paper, with no visible text or symbols.

12b UP 21 Pin

13a Pin Handle arm

Mechanical assembly diagram showing a rotating component with a handle and housing (no text or symbols)

Diagram of a mechanical device with a hand holding a tool, showing motion lines and no readable text or symbols.

Illustration of a hand using a tool to adjust or install a mechanical component (no text or symbols visible)

Mechanical assembly diagram showing a presser pressing a component with a downward arrow indicating motion (no text or symbols present)

Illustration of a hand holding a small mechanical component, no text or symbols present

17a

Line drawing of a hand holding a tool with an arrow indicating direction (no text or symbols)

Illustration of a portable air conditioner unit with a hand operating it, showing airflow direction (no text or symbols)

Line drawing of a device component with a button and label '18b' (no readable text or symbols beyond basic labels)

18c

Illustration of a cylindrical device with a mesh grille and a handle, no visible text or symbols

19a

19b

SE ALLTID TILL ATT DET FINNS TILLRÄCKLIG VENTILATION

Hand holding a tool with an upward arrow, no visible text or symbols

Diagram of hands operating a mechanical press or press device with a perforated base and directional arrows (no text or symbols)

Diagram of a portable air purifier with a door and vent, showing internal components and airflow direction (no text or symbols)

Diagram of a food oven with labeled parts and a label 'E' indicating a specific component.

F

G

Diagram showing a hand pressing down on a device labeled 'H' with an upward arrow, likely illustrating a process or operation.

Technical diagram of a microwave oven with labeled components and directional arrows indicating assembly or operation.

Diagram of a water tank with labeled components and connected piping, showing internal compartments and a delivery bag.

Two identical oval electronic components with pins, labeled 'leeg vol' below (no additional text or symbols)

Hand holding a circular object with an arrow indicating rotation, no text or symbols present

Hand holding a dial indicator with an arrow pointing to it, no text or symbols present

Illustration of a hand holding a circular object inside a cage-like structure, with arrows indicating direction (no text or symbols)

Hand holding a circular object with an arrow indicating rotation, no text or symbols present

D VÄRMARENS FÖRBRÄNNING

Hand holding a ball above a surface with two bubbles and an arrow indicating motion (no text or symbols)

Simple line drawing of a door with a battery and two stacked compartments, labeled G (no text or symbols)

VÄRMAREN FORTSÄTTER ATT BRINNA SVAGT

Technical diagram showing two steps of a hand pouring liquid into a container, labeled O and P.

transportskydd

K WARRANTY PROVISIONS

Line drawing of a hand using a tool to press or install a device on a tray (no text or symbols)

Diagram showing a mechanical or electrical component with polarity markings (+/-) and an identifier '2' in the corner.

Illustration of a hand pressing down on a mechanical component with no visible text or symbols

Diagram showing a hand holding a circular device with a gear and a labeled component, indicating rotation or adjustment.

Hand holding a tool with a circular button, no visible text or symbols

Line drawing of a device rear panel with a button and label (no readable text or symbols)

Illustration of a hand holding a portable air purifier with a scroll, showing airflow direction (no text or symbols)

Line drawing of a hand pressing down on a mechanical component (no text or symbols)

Mechanical assembly diagram showing a presser pressing a component with a valve (no text or symbols visible)

8a

Technical line drawing of a mechanical device with an arrow indicating motion (no text or symbols)

Mechanical assembly diagram showing a rotating component with a curved arrow indicating rotation (no text or symbols)

10 Pin Handle arm

Illustration of a hand holding a coiled object with a tool, no text or symbols present

BYTE AV VEKEN

L KONTROLLERA ATT VÄRMAREN ÄR AVSTÄNGD OCH HELT AVSVALNAD INNAN DU BYTER VEKE.

Illustration of a hand holding a rolled-up sheet of paper or paper, with no visible text or symbols.

12b UP 21 Pin

13a Pin Handle arm

Mechanical assembly diagram showing a rotating component with a handle and housing (no text or symbols)

Diagram of a mechanical device with a hand holding a tool, showing motion lines and no readable text or symbols.

Illustration of a hand using a screwdriver to adjust a mechanical component (no text or symbols visible)

Mechanical assembly diagram showing a presser pressing a component with a downward arrow indicating motion (no text or symbols present)

Illustration of a hand holding a small mechanical component, no text or symbols present

17a

Line drawing of a hand holding a car seatbelt with a directional arrow indicating motion (no text or symbols)

18a

Line drawing of a device component with a 18lb mark and a button, no text or symbols present

18c

Line drawing of a cylindrical device with a mesh grille and handle, partially held by hands (no text or symbols)

19a

19b

3D rendering of a cylindrical industrial filter or vent with mesh pattern and mounting base (no text or symbols)

1-3 cm.

Illustration of a cylindrical industrial or filtration device with perforated internal structure and mounting base (no text or symbols)

Q

Technical diagram of a portable air heater with numbered parts and close-ups of internal components

zibro www.zibro.com

Distributed in Europe by PVG Holding B.V.

D Benötigen Sie weitere Informationen oder treten Probleme auf, besuchen Sie bitte unsere Website www.zibro.com, oder setzen Sie sich mit unserem Kundendienst in Verbindung (Telefonnummer auf www.zibro.com).
For alle yderligere oplysninger eller ved eventuelle problemer med apparatet henvises til www.zibro.com eller det lokale Kundecenter (telefonnumre findes i www.zibro.com).
Si necesita información o si tiene algún problema, visite nuestra página Web www.zibro.com, o póngase en contacto con el servicio cliente (hallará el número de teléfono en www.zibro.com).
Si vous souhaitez obtenir des informations supplémentaires ou si vous rencontrez un problème, rendez-vous sur notre site Web (www.zibro.com) ou contactez notre service client (vous trouverez l'adresse et numéro de téléphone sur www.zibro.com).
Jos haluat huoltoapua, lisätietoja tai laitteen kanssa tulee ongelmia, tutustu verkkosivustoon osoitteessa www.zibro.com tai kysy neuvoa PVG kuluttajapalvelukeskuksesta (www.zibro.com).
If you need information or if you have a problem, please visit the our website (www.zibro.com) or contact our sales support (you find its phone number on www.zibro.com)
Per informazioni e in caso di problemi, visitate il sito Web www.zibro.com oppure contattate il Centro Assistenza Clienti (per conoscere il numero di telefono, consultate www.zibro.com).
Hvis du trenger informasjon, eller hvis du har et problem med produktet, kan du gå til nettsidene www.zibro.com. Alternativt kan du kontakte med PVG' forbrukertjeneste (telefonnummeret i www.zibro.com).
Als u informatie nodig hebt of als u een probleem hebt, bezoek dan de onze website (www.zibro.com) of neem contact op met de afdeling sales support (adres en telefoon op www.zibro.com).
Se necessitar de informações ou se tiver problemas, visite o Web site www.zibro.com ou contacte o Centro de Assistência (número de telefone o www.zibro.com)
W przypadku problemów i w celu uzyskania szczegółowych informacji odwiedź stronę internetową Zibro dostępną pod adresem www.zibro.com lub skontaktuj się z Centrum kontaktów Zibro (www.zibro.com)
⑧ Om du behöver service eller information eller har problem med apparaten kan du besöka www.zibro.com eller kontakta Zibro kundtjänst (du hittar telefonnumret på www.zibro.com).
Če želite dodatne informacije, obiščite spletno mesto podjetja na naslovu www.zibro.com ali pokličite na teleforsko (www.zibro.com).
Daha fazla bilgiye ihtiyaç duyarsanız veya bir sorunla karşılaşırsanız, www.zibro.com adresindeki Zibro Internet sitesini ziyaret edin veya ülkenizde bulunan Zibro müşteri merkeziyle iletişim kurun (telefon numarasını; www.zibro.com).

Zibro® is registered trademark of TOYOTOMI Co., Ltd. for paraffi n heaters.

ZIBRO brand paraffin heaters are made in Japan and imported by PVG Holding B.V.