PROMIX220U - Mixer HQ Power - Free user manual and instructions
Find the device manual for free PROMIX220U HQ Power in PDF.
| Product type | Mixing console |
| Brand | HQ Power |
| Model | PROMIX220U |
| Power supply | 100-240 VAC, 50/60 Hz |
| Power consumption | 30 W |
| Dimensions | 290 x 226 x 117 mm |
| Frequency response | 20 Hz - 20 kHz |
| Signal-to-noise ratio (LINE) | 85 dB |
| Signal-to-noise ratio (PHONO) | 75 dB |
| Signal-to-noise ratio (MIC) | 70 dB |
| Harmonic distortion (LINE/PHONO) | < 0.02% |
| Crosstalk | > 15 dB |
| Per-channel equalizer | HI +12/-24 dB (13 kHz), MID +12/-24 dB (1 kHz), LOW +12/-24 dB (70 Hz) |
| Microphone equalizer | HI +12/-12 dB (10 kHz), MID +12/-12 dB (1 kHz), LOW +12/-12 dB (100 Hz) |
| Inputs | 2 x LINE (RCA), 1 x PHONO (RCA), 1 x MIC (Combo 6.35 mm), 1 x USB |
| Outputs | Master XLR, Master RCA, Booth RCA, Rec RCA, Headphones (6.35 mm) |
| Main features | Trim, peak meter, talk-over, crossfader (2 curves), headphone Cue/Master balance, 3-band equalizer per channel and microphone |
| Maintenance | Disconnect before cleaning, damp lint-free cloth, no alcohol or solvents |
| Safety | Indoor use, avoid moisture and splashes, do not block vents |
| Repairability | No user-serviceable parts, contact dealer |
| Warranty | 24 months for consumer use (conditions in manual) |
Frequently Asked Questions - PROMIX220U HQ Power
User questions about PROMIX220U HQ Power
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Mixer in PDF format for free! Find your manual PROMIX220U - HQ Power and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. PROMIX220U by HQ Power.
USER MANUAL PROMIX220U HQ Power
To all residents of the European Union
Important environmental information about this product
This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialized company for recycling. This device should be returned to your distributor or to a local recycling service. Respect the local environmental rules.
If in doubt, contact your local waste disposal authorities.
Thank you for choosing HQPower™! Please read the manual thoroughly before bringing this device into service. If the device was damaged in transit, don't install or use it and contact your dealer.
2. Safety Instructions
Be very careful during the installation: touching live wires can cause life-threatening electroshocks.
Always disconnect mains power when device not in use or when servicing or maintenance activities are performed. Handle the power cord by the plug only.
Keep this device away from children and unauthorized users.
There are no user-serviceable parts inside the device. Refer to an authorized dealer for service and/or spare parts.
• Make sure that the available voltage does not exceed the voltage stated in the specifications of this manual.
- Do not crimp the power cord and protect it against damage. Have an authorised dealer replace it if necessary.
3. General Guidelines
Refer to the Velleman® Service and Quality Warranty on the last pages of this manual.
Indoor use only. Keep this device away from rain, moisture, splashing and dripping liquids. Never put objects filled with liquid on top of or close to the device.
Keep this device away from dust and extreme heat. Make sure the ventilation openings are clear at all times. For sufficient air circulation, leave at least 1" (± 2.5 cm) in front of the openings.
Protect this device from shocks and abuse. Avoid brute force when operating the device.
- Familiarise yourself with the functions of the device before actually using it. Do not allow operation by unqualified people. Any damage that may occur will most probably be due to unprofessional use of the device.
- All modifications of the device are forbidden for safety reasons. Damage caused by user modifications to the device is not covered by the warranty.
- Only use the device for its intended purpose. All other uses may lead to short circuits, burns, electroshocks, lamp explosion, crash, etc. Using the device in an unauthorised way will void the warranty.
- Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the dealer will not accept responsibility for any ensuing defects or problems.
• A qualified technician should install and service this device. - Do not switch the device on immediately after it has been exposed to changes in temperature. Protect the device against damage by leaving it switched off until it has reached room temperature.
- This device is designed for professional use on stage, in discos, theatres, etc. It should only be used indoors with an alternating current of 230 VAC/50 Hz.
- Use high-quality shielded cables with low capacitance throughout the system.
- Avoid using excessively long cables. Make sure all plugs and jacks are in perfect working order to avoid hum, noise and popsthat could damage speakers.
-
Route one cable at the time. Pay attention to the labelled audio input and output jacks.
-
Always begin with the master faders, volume controls and the amplifier volume at minimum position. Gradually turn up the volume after connection is completed.
• Use the controls with restraint. Rapid movements may damage the speakers due to amplifier clipping.
• Use the original packaging if the device is to be transported. - Keep this manual for future reference.
4. Features
• outputs: 2 Master (XLR and RCA), 1 Rec (RCA) and booth monitor output (RCA)
- inputs: 1 Phono (RCA), 2 Line (RCA) and 1 MIC (Combi)
- trim: gain for each input channel
- peak level meter: allows the user to instantly determine the source input condition for each channel
- talk over: mutes -14dB all levels apart from the microphone
• cross fader curve: choose from two types of cross fader start-up options
- headphone monitor balance between cue and master out
• gain control with 3-fold sound control (+12/-24dB) per channel
- MIC channel 1 with 3-fold sound control (+12/-12dB), gain, cue and talk-over
• ultra high-performance headphones output, 1-way equalizer, cue-master-mix.
5. Overview
Refer to the illustrations on page 2 of this manual.
| 1 | power switch: turn the mixer on or off. |
| 2 | POWER SUPPLY INPUT: connect to 230VAC/50Hz power source |
| 3 | Balanced master outputs: audio output signal connectors (XLR, symmetrical) |
| 4 | Master RCA output: RCA connection to an auxiliary amplifier (not included) |
| 5 | BOOTH: RCA connection for booth monitor (not included) |
| 6 | REC: RCA connection to recording device (not included) |
| 7 | CONTROL A/ B: CD player inputs |
| 8 | USB: USB input |
| 9 | Input connectors (CH2-CH1): connect an external device (not incl., e.g. turntable, CD player...) to these RCA (cinch) connectors. |
| 10 | GND (ground) connection: when buzzing occurs, connect to turntables to create earth connection. |
| 11 | PHONES OUT: plug a headphone into this jack for audio monitoring |
| 12 | 6.35mm microphone input (microphone not incl.)MIC LEVEL: adjust the microphone input levelHI/ MID/ LOW: microphone equalizer |
| 13 | Input channel controls (CH1/CH2)Input selector switches:Channel 1: LINE or PHONO. Set to PHONO if a turntable (not incl.) is connected to the input; otherwise set to LINE.Channel 2: LINE or USB. Set to USB if an input device is connected via the USB port [8]; otherwise set to LINE.TRIM: adjust the input signal levelHI/ MID/ LOW: channel equalizer |
| 14 | LED meter: indicates the master output level |
| 15 | TALK OVER: press this button to decrease the sound level for everything other than the main microphone to 14dB. Press again to restore original status. |
| 16 | Headphones controlsPHONES LEVEL: adjust the output level of the headphonesCUE: mixing adjustment knob. Turn to the left to hear channel 1. Turn to the right to hear channel 2. At the centre position, the levels for both channels are even. |
| 17 | Cross fader: moving the slider from left to right will fade in channel 2 (louder) while fading out channel 1 (more quiet). In the middle position, both channels are played at equal volume. |
| 18 | MASTER BALANCE: adjust the left-right balance of the master output |
| 19 | Channel fader: set level of the channels with these sliders. |
| 20 | Master fader: master volume control |
| 21 | Cross fader curve selector: select one of the cross fader start-up curves (abrupt or smooth transition). |
| 22 | BOOTH MONITOR: adjust the level of the booth monitor |
6. Cleaning and maintenance
- All screws should be tightened and free of corrosion.
- The housing, visible parts, mounting supports and the installation location (e.g. ceiling, suspension, trussing) should not be deformed, modified or tampered with e.g. do not drill extra holes in mounting supports, do not change the location of the connections.
- Moving mechanic parts must not show any signs of wear and tear.
- The electric power supply cables must not show any damage. Have a qualified technician maintain the device.
- Disconnect the device from the mains prior to maintenance activities.
- Wipe the device regularly with a moist, lint-free cloth. Do not use alcohol or solvents.
- There are no user-serviceable parts.
-
Contact your dealer for spare parts if necessary.
-
Technical Specifications
| power supply 100-240Vac ~ 50/60Hz | ||
| power consumption 30W | ||
| input terminal LINE 400mV | ||
| PHONO | 15mV | |
| MIC | 10mV/ | |
| frequency response 20Hz-20KHz | ||
| S/N ratio LINE 85dB | ||
| PHONO | 75dB | |
| MIC | 70dB | |
| THD | LINE/PHONO | < 0.02% |
| crosstalk | > 15dB | |
| channel equalizer | HI +12dB, -24dB (13kHz) | |
| MID | +12dB, -24dB (1kHz) | |
| LOW +12dB, -24dB (70Hz) | ||
| MIC equalizer | HI +12dB, -12dB (10kHz) | |
| MID | +12dB, -12dB (1kHz) | |
| LOW +12dB, -12dB (100Hz) | ||
| dimensions | 290 x 226 x 117mm (11.4" x 8.9" x 4.6") | |
Use this device with original accessories only. Velleman nv cannot be held responsible in the event of damage or injury resulted from (incorrect) use of this device.
For more info concerning this product and the latest version of this manual, please visit our website www.hqpower.eu.
The information in this manual is subject to change without prior notice.
© COPYRIGHT NOTICE
The copyright to this manual is owned by Velleman nv. All worldwide rights reserved.
No part of this manual or may be copied, reproduced, translated or reduced to any electronic medium or otherwise without the prior written consent of the copyright holder.
Velleman® Service and Quality Warranty
Since its foundation in 1972, Velleman® acquired extensive experience in the electronics world and currently distributes its products in over 85 countries.
All our products fulfil strict quality requirements and legal stipulations in the EU. In order to ensure the quality, our products regularly go through an extra quality check, both by an internal quality department and by specialized external organisations. If, all precautionary measures notwithstanding, problems should occur, please make appeal to our warranty (see guarantee conditions).
General Warranty Conditions Concerning Consumer Products (for EU):
- All consumer products are subject to a 24-month warranty on production flaws and defective material as from the original date of purchase.
- Velleman® can decide to replace an article with an equivalent article, or to refund the retail value totally or partially when the complaint is valid and a free repair or replacement of the article is impossible, or if the expenses are out of proportion. You will be delivered a replacing article or a refund at the value of 100% of the purchase price in case of a flaw occurred in the first year after the date of purchase and delivery, or a replacing article at 50% of the purchase price or a refund at the value of 50% of the retail value in case of a flaw occurred in the second year after the date of purchase and delivery.
• Not covered by warranty:
- all direct or indirect damage caused after delivery to the article (e.g. by oxidation, shocks, falls, dust, dirt, humidity...), and by the article, as well as its contents (e.g. data loss), compensation for loss of profits;
- consumable goods, parts or accessories that are subject to an aging process during normal use, such as batteries (rechargeable, non-rechargeable, built-in or replaceable), lamps, rubber parts, drive belts... (unlimited list);
- flaws resulting from fire, water damage, lightning, accident, natural disaster, etc....;
- flaws caused deliberately, negligently or resulting from improper handling, negligent maintenance, abusive use or use contrary to the manufacturer's instructions;
- damage caused by a commercial, professional or collective use of the article (the warranty validity will be reduced to six (6) months when the article is used professionally);
- damage resulting from an inappropriate packing and shipping of the article;
- all damage caused by modification, repair or alteration performed by a third party without written permission by Velleman®.
- Articles to be repaired must be delivered to your Velleman® dealer, solidly packed (preferably in the original packaging), and be completed with the original receipt of purchase and a clear flaw description.
- Hint: In order to save on cost and time, please reread the manual and check if the flaw is caused by obvious causes prior to presenting the article for repair. Note that returning a non-defective article can also involve handling costs.
- Repairs occurring after warranty expiration are subject to shipping costs.
- The above conditions are without prejudice to all commercial warranties.
The above enumeration is subject to modification according to the article (see article's manual).
