DDF470RF3J - Drill MAKITA - Free user manual and instructions

USER MANUAL DDF470RF3J MAKITA

34 ENGLISH ENGLISH (Original instructions)

Drilling capacities Steel 13 mm

Fastening capacities Wood screw 10 mm x 90 mm

Overall length 185 mm

Rated voltage D.C. 14.4 V Net weight 1.4 - 1.7 kg

• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange

• Theweightmaydi󰀨erdependingontheattachment(s),includingthebatterycartridge.Thelightestandheavi-

estcombination,accordingtoEPTA-Procedure01/2014,areshowninthetable.

Applicable battery cartridge and charger

WARNING: Only use the battery cartridges and chargers listed above.Useofanyotherbatterycartridges

andchargersmaycauseinjuryand/orre.

The tool is intended for drilling and screw driving in

wood, metal and plastic.

ThetypicalA-weightednoiseleveldeterminedaccord-

Sound pressure level (L

NOTE: The declared noise emission value(s) has

WARNING: Wear ear protection.

WARNING: The noise emission during actual

use of the power tool can di󰀨er from the declared

value(s) depending on the ways in which the

tool is used especially what kind of workpiece is

WARNING: Be sure to identify safety mea-

sures to protect the operator that are based on an

estimation of exposure in the actual conditions of

use (taking account of all parts of the operating

cycle such as the times when the tool is switched

o󰀨 and when it is running idle in addition to the

Vibrationemission(a

measured in accordance with a standard test method

NOTE:Thedeclaredvibrationtotalvalue(s)mayalso

beusedinapreliminaryassessmentofexposure.5 ENGLISH WARNING:

The vibration emission during actual

use of the power tool can di󰀨er from the declared val-

ue(s) depending on the ways in which the tool is used

especially what kind of workpiece is processed.

Be sure to identify safety measures

to protect the operator that are based on an estima-

tion of exposure in the actual conditions of use (tak-

ing account of all parts of the operating cycle such

as the times when the tool is switched o󰀨 and when

it is running idle in addition to the trigger time).

EC Declaration of Conformity

For European countries only

TheECdeclarationofconformityisincludedasAnnexA

to this instruction manual.

SAFETY WARNINGS General power tool safety warnings

WARNING: Read all safety warnings, instruc-

tions, illustrations and specications provided

with this power tool. Failure to follow all instructions

listedbelowmayresultinelectricshock,reand/or

Save all warnings and instruc-

Theterm"powertool"inthewarningsreferstoyour

mains-operated(corded)powertoolorbattery-operated

(cordless) power tool.

Cordless driver drill safety warnings

Safety instructions for all operations

1. Hold the power tool by insulated gripping

surfaces, when performing an operation where

the cutting accessory or fasteners may contact

hidden wiring. Cuttingaccessoryorfasteners

contactinga"live"wiremaymakeexposedmetal

parts of the power tool "live" and could give the

operator an electric shock.

2. Always be sure you have a rm footing. Be

sure no one is below when using the tool in

3. Hold the tool rmly.

4. Keep hands away from rotating parts.

5. Do not leave the tool running. Operate the tool

only when hand-held.

6. Do not touch the drill bit or the workpiece

immediately after operation; they may be

extremely hot and could burn your skin.

Some material contains chemicals which may be

toxic. Take caution to prevent dust inhalation and

skin contact. Follow material supplier safety data.

8. If the drill bit cannot be loosened even you

open the jaws, use pliers to pull it out. In such a

case,pullingoutthedrillbitbyhandmayresultin

injurybyitssharpedge.

Safety instructions when using long drill bits

1. Never operate at higher speed than the max-

imum speed rating of the drill bit.Athigher

speeds,thebitislikelytobendifallowedtorotate

freelywithoutcontactingtheworkpiece,resulting

2. Always start drilling at low speed and with the

bit tip in contact with the workpiece.Athigher

speeds,thebitislikelytobendifallowedtorotate

freelywithoutcontactingtheworkpiece,resulting

3. Apply pressure only in direct line with the bit

and do not apply excessive pressure. Bits can

bendcausingbreakageorlossofcontrol,resulting

SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity

with product (gained from repeated use) replace

strict adherence to safety rules for the subject

product. MISUSE or failure to follow the safety

rules stated in this instruction manual may cause

serious personal injury.

Important safety instructions for

Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery char-

ger, (2) battery, and (3) product using battery.

2. Do not disassemble or tamper the battery

cartridge.Itmayresultinare,excessiveheat,

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

4. If electrolyte gets into your eyes, rinse them

out with clear water and seek medical atten-

tion right away. It may result in loss of your

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any con-

(2) Avoid storing battery cartridge in a con-

tainer with other metal objects such as

(3) Do not expose battery cartridge to water

A battery short can cause a large current

ow, overheating, possible burns and even a

6. Do not store and use the tool and battery car-

tridge in locations where the temperature may

reach or exceed 50 °C (122 °F).

7. Do not incinerate the battery cartridge even if

it is severely damaged or is completely worn

out. The battery cartridge can explode in a re.

8. Do not nail, cut, crush, throw, drop the battery

cartridge, or hit against a hard object to the

battery cartridge.Suchconductmayresultina

re,excessiveheat,orexplosion.

9. Do not use a damaged battery.6 ENGLISH

The contained lithium-ion batteries are subject to

the Dangerous Goods Legislation requirements.

Forcommercialtransportse.g.bythirdparties,

forwarding agents, special requirement on pack-

agingandlabelingmustbeobserved.

Forpreparationoftheitembeingshipped,consult-

ing an expert for hazardous material is required.

Pleasealsoobservepossiblymoredetailed

national regulations.

Tapeormasko󰀨opencontactsandpackupthe

batteryinsuchamannerthatitcannotmove

around in the packaging.

11. When disposing the battery cartridge, remove

it from the tool and dispose of it in a safe

place. Follow your local regulations relating to

disposal of battery.

12. Use the batteries only with the products

specied by Makita.Installingthebatteriesto

non-compliantproductsmayresultinare,exces-

siveheat,explosion,orleakofelectrolyte.

13. If the tool is not used for a long period of time,

the battery must be removed from the tool.

14. During and after use, the battery cartridge may

take on heat which can cause burns or low

temperature burns. Pay attention to the han-

dling of hot battery cartridges.

15. Do not touch the terminal of the tool imme-

diately after use as it may get hot enough to

16. Do not allow chips, dust, or soil stuck into the

terminals, holes, and grooves of the battery

cartridge.Itmayresultinpoorperformanceor

breakdownofthetoolorbatterycartridge.

17. Unless the tool supports the use near

high-voltage electrical power lines, do not use

the battery cartridge near high-voltage electri-

cal power lines.Itmayresultinamalfunctionor

breakdownofthetoolorbatterycartridge.

18. Keep the battery away from children.

SAVE THESE INSTRUCTIONS.

CAUTION: Only use genuine Makita batteries.

Useofnon-genuineMakitabatteries,orbatteriesthat

1. Charge the battery cartridge before completely

discharged. Always stop tool operation and

charge the battery cartridge when you notice

2. Never recharge a fully charged battery car-

tridge. Overcharging shortens the battery

Charge the battery cartridge with room tempera-

ture at 10 °C - 40 °C (50 °F - 104 °F). Let a hot

battery cartridge cool down before charging it.

4. When not using the battery cartridge, remove

it from the tool or the charger.

5. Charge the battery cartridge if you do not use

it for a long period (more than six months).

FUNCTIONAL DESCRIPTION CAUTION: Always be sure that the tool is

switched o󰀨 and the battery cartridge is removed

before adjusting or checking function on the tool.

Installing or removing battery cartridge

CAUTION: Always switch o󰀨 the tool before

installing or removing of the battery cartridge.

CAUTION: Hold the tool and the battery car-

tridge rmly when installing or removing battery

cartridge.Failuretoholdthetoolandthebattery

cartridgermlymaycausethemtoslipo󰀨yourhands

andapersonalinjury.

►Fig.1: 1. Red indicator 2. Button 3.Batterycartridge

Toremovethebatterycartridge,slideitfromthetool

whileslidingthebuttononthefrontofthecartridge.

withalittleclick.Ifyoucanseetheredindicatoronthe

uppersideofthebutton,itisnotlockedcompletely.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen. If not,

itmayaccidentallyfalloutofthetool,causinginjuryto

youorsomeonearoundyou.

CAUTION: Do not install the battery cartridge

forcibly.Ifthecartridgedoesnotslideineasily,itis

notbeinginsertedcorrectly.

Indicating the remaining battery capacity

Only for battery cartridges with the indicator

►Fig.2: 1. Indicator lamps 2.Checkbutton

Pressthecheckbuttononthebatterycartridgetoindi-

catetheremainingbatterycapacity.Theindicatorlamps

light up for a few seconds.

Indicator lamps Remaining capacityLighted O󰀨 Blinking75% to 100%50% to 75%25% to 50%0% to 25%Charge the battery.Thebatterymayhavemalfunctioned.7 ENGLISH NOTE: Depending on the conditions of use and the

ambienttemperature,theindicationmaydi󰀨erslightly

fromtheactualcapacity.

NOTE:Therst(farleft)indicatorlampwillblinkwhen

thebatteryprotectionsystemworks.

Tool / battery protection system

Thetoolisequippedwithatool/batteryprotectionsys-

underoneofthefollowingconditions:

This protection works when the tool is operated in a

mannerthatcausesittodrawanabnormallyhighcur-

rent.Inthissituation,turnthetoolo󰀨andstoptheappli-

cationthatcausedthetooltobecomeoverloaded.Then

turn the tool on to restart.

capacitygetslow.Inthissituation,removethebattery

fromthetoolandchargethebattery.

Indicating the remaining battery

Whenyoupulltheswitchtrigger,theLEDdisplayshows

theremainingbatterycapacity.Theremainingbattery

capacityisshownasthefollowingtable.

►Fig.3: 1.Batteryindicator

Battery indicator status Remaining battery

minute after releasing the switch trigger.

►Fig.4: 1. Switch trigger

CAUTION: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the "OFF" position when released.

Tostartthetool,simplypulltheswitchtrigger.Tool

speedisincreasedbyincreasingpressureontheswitch

trigger. Release the switch trigger to stop.

Lighting up the front lamp

CAUTION: Do not look in the light or see the

source of light directly.

Pulltheswitchtriggertolightupthelamp.Thelamp

keepsonlightingwhiletheswitchtriggerisbeingpulled.

Thelampgoesoutapproximately10secondsafter

releasing the switch trigger.

NOTE: When the tool is overheated, the tool stops

automaticallyandthelampstartsashing.Inthis

the lamp. Be careful not to scratch the lens of lamp, or

Reversing switch action

►Fig.6: 1. Reversing switch lever

CAUTION: Always check the direction of

rotation before operation.

CAUTION: Use the reversing switch only after

the tool comes to a complete stop. Changing the

directionofrotationbeforethetoolstopsmaydam-

CAUTION: When not operating the tool,

always set the reversing switch lever to the neu-

This tool has a reversing switch to change the direction

of rotation. Depress the reversing switch lever from the

AsideforclockwiserotationorfromtheBsideforcoun-

terclockwise rotation.

When the reversing switch lever is in the neutral posi-

►Fig.7: 1. Speed change lever

CAUTION: Always set the speed change lever

fully to the correct position.Ifyouoperatethe

toolwiththespeedchangeleverpositionedhalfway

betweenthe"1"sideand"2"side,thetoolmaybe

CAUTION: Do not use the speed change lever

2 High Low Light loading

Tochangethespeed,switcho󰀨thetoolrst.Select

the"2"sideforhighspeedor"1"forlowspeedbuthigh

torque. Be sure that the speed change lever is set to the

correctpositionbeforeoperation.

Ifthetoolspeediscomingdownextremelyduringthe

operation with "2", slide the lever to the "1" and restart

Adjusting the fastening torque

Beforeactualoperation,driveatrialscrewintoyourmaterialorapieceofduplicatematerialtodeterminewhich

torque level is required for a particular application.

Thefollowingshowstheroughguideoftherelationshipbetweenthescrewsizeandgraduation.

Graduation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

– ø3.5 x 22 ø4.1x 38 –

ASSEMBLY CAUTION: Always be sure that the tool is

switched o󰀨 and the battery cartridge is removed

before carrying out any work on the tool.

Installing or removing driver bit/drill bit

Turnthesleevecounterclockwisetoopenthechuckjaws.

Turn the sleeve clockwise to tighten the chuck. To remove

When installing the hook, always

secure it with the screw rmly.Ifnot,thehookmay

comeo󰀨fromthetoolandresultinthepersonalinjury.

Thiscanbeinstalledoneithersideofthetool.Toinstall

the hook, insert it into a groove in the tool housing on

either side and then secure it with a screw. To remove,

loosen the screw and then take it out.

Installing driver bit holder

►Fig.11: 1.Driverbitholder2.Driverbit

on either right or left side and secure it with a screw.

holders.Driverbits45mm-longcanbekeptthere.

all the way until it locks in place.Ifyoucanseethe

CAUTION: When the speed comes down

extremely, reduce the load or stop the tool to

avoid the tool damage.

Holdthetoolrmlywithonehandonthegripandthe

otherhandonthebottomofthebatterycartridgeto

control the twisting action.

Screwdriving operation

CAUTION: Adjust the adjusting ring to the

proper torque level for your work.

CAUTION: Make sure that the driver bit is

inserted straight in the screw head, or the screw

and/or driver bit may be damaged.

Placethepointofthedriverbitinthescrewheadand

applypressuretothetool.Startthetoolslowlyandthen

increasethespeedgradually.Releasetheswitchtrigger

as soon as the clutch cuts in.

NOTE: When driving wood screw, pre-drill a pilot hole

2/3thediameterofthescrew.Itmakesdrivingeasier

and prevents splitting of the workpiece.9 ENGLISH Drilling operation

First,turntheadjustingringsothatthearrowpointsto

the marking. Then proceed as follows.

Whendrillinginwood,thebestresultsareobtained

with wood drills equipped with a guide screw. The guide

hole, make an indentation with a center-punch and

drillbitintheindentationandstartdrilling.

Useacuttinglubricantwhendrillingmetals.Theexcep-

tionsareironandbrasswhichshouldbedrilleddry.

CAUTION: Pressing excessively on the tool

will not speed up the drilling. In fact, this excessive

pressurewillonlyservetodamagethetipofyourdrill

bit,decreasethetoolperformanceandshortenthe

service life of the tool.

CAUTION: Hold the tool rmly and exert care

when the drill bit begins to break through the

workpiece. There is a tremendous force exerted on

thetool/drillbitatthetimeofholebreakthrough.

CAUTION: A stuck drill bit can be removed

simply by setting the reversing switch to reverse

rotation in order to back out. However, the tool

may back out abruptly if you do not hold it rmly.

CAUTION: Always secure workpieces in a

vise or similar hold-down device.

CAUTION: If the tool is operated continuously

until the battery cartridge has discharged, allow

the tool to rest for 15 minutes before proceeding

with a fresh battery.

MAINTENANCE CAUTION: Always be sure that the tool is

switched o󰀨 and the battery cartridge is removed

before attempting to perform inspection or

NOTICE: Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or

Centers,alwaysusingMakitareplacementparts.

OPTIONAL ACCESSORIES CAUTION: These accessories or attachments

are recommended for use with your Makita tool

specied in this manual.Theuseofanyother

accessories or attachments might present a risk of

injurytopersons.Onlyuseaccessoryorattachment

for its stated purpose.

WAARSCHUWING: De trillingsemissie tij-

Vibrationsemission(a

Sikkerhedsadvarsler for akku