L.450 X L.2.5 X H.1.4 M - Above-ground pool UBBINK - Free user manual and instructions

USER MANUAL L.450 X L.2.5 X H.1.4 M UBBINK

Exterior view of a wooden structure with ladder and support structure, surrounded by grass and shrubs (no signage or text visible)

Warning symbol image with exclamation mark inside triangle

• NOTEZ IMPERATIVEMENT CI-DESSOUS LES NUMEROS DE SERIE DE LA STRUCTURE ET DU LINER DE VOTRE PISCINE (exemple en page 8)
  • STRUKTUR UND SCHWIMMBADFOLIE IHRES POOLS (Beispiel auf Seite 8)
• CONSTRUCTIE EN FOLIE VAN UW POOL(voorbeeld op blz. 8)
  • STRUCTURE AND LINER OF YOUR POOL (example on page 8)
• ESTRUCTURA Y LINER DE SU PISCINA (ejemplo en la página 8)
  • STRUTTURA E DEL LINER DELLA PISCINA (esempio a pag. 8)

Serial number of the structure: ....

Please read carefully and keep for future reference

- Maintenance and Safety Notice

FOREWORD

Wood, which is the main element used in building UBBINK® swimming pools, is a living substance and is liable to becoming warped if stored in adverse conditions. Make sure that you store all the wooden parts flat in a cool, well ventilated place, out of the sun and protected from bad weather.

• Whilst assembling the pool, make sure you sand down the catches on the wooden parts with a file or sandpaper in order to get rid of any potential splinters.
• Any cracks, knots and small faults on the surface of the strips do not in any way affect the wood's resistance. It certainly shouldn't be necessary to claim a replacement. Do not fill the cracks with putty or any other material.
• It is recommended that you have professional help when assembling the pool.
• The coping is a finishing element. It is strictly forbidden to run or sit on it.
• It is essential that the filter is installed below the level of the water;

SAFETY

The safety of your children is entirely your responsibility! The risk is greatest with children under 5 years old.

Accidents do not just happen to other people! Be ready to deal with them!

be vigilant and take action:

• When using the swimming pool it is essential to comply with the safety procedures described in the handbook on maintenance and use. Failure to follow instructions regarding maintenance may endanger life, especially where children are concerned.
  • children should be closely supervised at all times;
• designate one person to be responsible for safety;
  • have extra supervision when the pool is being used by several children;
  • make sure that there is equipment to keep anyone who cannot swim afloat;
• tteach your children to swim as early as possible;
• wet your neck, arms and legs before getting into the water;
• learn life-saving techniques, especially those specifically used for children;
• do not allow diving or jumping in near young children;
• do not allow running or boisterous games around the edges of the pool;
• do not allow any child who is not a strong swimmer and is unaccompanied to get into the pool without a life jacket on;
• it is a good idea to remove the outside wooden ladder each time you have finished using your pool so that there is no unsupervised access;
• do not leave any toys near or in the pool if it is not being supervised;
• keep the water crystal clear and sanitised;
• store water treatment products out of reach of children;
• do not use any sharp or pointed object in the pool (which may damage the liner);
• never put treatment products directly into the water (this may cause staining on the liner);
• It is essential that the electrical appliances must be operated with an earth leakage circuit breaker (RCD) with a rated fault current of ≤ 30 mA.

• Do not allow anyone to go into the pool if the filtration system(s) is (are) not functioning properly.

• All the filters conform to safety standard EN 60335-2-41 (France : NF C15-100) which stipulates that all electrical appliances installed at less than 3.5m from the pool and freely accessible must run on a very low power supply 12V. All electrical appliances that run on 220-240 VAC must be situated at least 3.5m (appliance) and 2,00m (plug) from the edge of the pool. Seek advice from the manufacturer regarding any changes to one or more elements of the filtration system.

• A Replacement of the net cable is not possible. In order to avoid any hazards, the electrical appliance must be taken out of operation in case the connecting cable gets damaged.
• Where possible check the bolts and screws (e.g. for any signs of rust).
• During the excavation phase make sure that the side walls are secured.

In your planning:

• the telephone should be positioned near the pool so that you can supervise your children whilst you are on the phone;
• an Inflatable ring and a pole should be kept near the pool;
• moreover, certain types of equipment may contribute to safety;

a) there should be a protective barrier with the gate always kept shut (e.g. a hedge cannot be regarded as a barrier); b) a manual or automatic cover should be correctly in place and secured;

c) an electronic detector which picks up anyone going in or falling in should be fitted and operating

but this does not in any way replace close supervision;

If an accident occurs:

• get the child out of the water as fast as possible;
- call for help immediately and follow the advice you are given;
- remove wet clothing and wrap in warm blankets;
- memorise emergency numbers and put them on a notice near the pool :
- European emergency no: 112
- National Poisons Information Service

Leer atentamente y conservar para su consulta ulterior

- Aviso

PRÓLOGO

GARANTIES PISCINES UBBINK®

Piscine 250x450 - H140 cm Urban Pool

Close-up of a textured surface with horizontal dark bands (no visible text or symbols)

Fentes

Close-up of a wooden surface with a small metallic object and a circular hole, no visible text or symbols.

Résine

Close-up of a wooden surface with horizontal grooves and grainy texture (no text or symbols)

A plain beige surface with a single horizontal brown line across the center (no text or symbols)

Close-up of a wooden surface with visible grain patterns and texture (no text or symbols)

Noeuds ronds

Close-up of a wooden surface with visible grain patterns and texture (no text or symbols)

Close-up of a wooden surface with horizontal striations and small white marks (no text or symbols visible)

Ref: J514009 Later 50/100 Size 300um H 120cm Blue Inner 50/100-365um H 120cm 10.0715924

FD FA MGE-D MGI-D B2 MGE-G R MGI-G MSE-1 JD MSE-2 2MSG-CF BR MS-CF P MSI-CF 2MSD-CF PS-1 PS-2 RC-1 RC-2 MRS M1 PJ MRS PA C B1 B2 MPI MSS MEP JAR JA PF R-C1 R-C2 PL ME PRG

Liste des pièces :

Close-up of a textured surface with horizontal dark bands (no visible text or symbols)

Close-up of a wooden surface with a small metallic object and a circular hole, no visible text or symbols.

Spalten

Close-up of a wooden surface with horizontal grooves and grainy texture (no text or symbols)

Farbunterschiede

A plain beige surface with a single horizontal brown line across the center (no text or symbols)

lange

Close-up of a wooden surface with visible grain patterns and texture (no text or symbols)

Runde Astlöcher

Close-up of a wooden surface with natural grain patterns (no text or symbols)

Close-up of a wooden surface with horizontal striations and small white marks (no text or symbols visible)

Oberflächenschimmel

DURCH DIE GARANTIE GEDECKT

Ref: J514009 Later 50/100 Size 300um H 120cm Blue Inner 50/100-365um H 120cm 10.0715924

FD FA MGE-D MGI-D B2 MGE-G R MGI-G MSE-1 JD MSE-2 2MSG-CF BR MS-CF P MSI-CF 2MSD-CF PS-1 PS-2 RC-1 RC-2 MRS M1 PJ MRS PA C B1 B2 MPI MSS MEP JAR JA PF R-C1 R-C2 PL ME PRG

Stückliste:

Close-up of a textured surface with horizontal dark bands (no visible text or symbols)

Groeven

Close-up of a wooden surface with a small metallic object and a hole, no visible text or symbols

Hars

Close-up of a wooden surface with horizontal grooves and grainy texture (no text or symbols)

Kleurverschillen

A plain beige surface with a single horizontal brown line across the center (no text or symbols)

Close-up of a wooden surface with natural grain patterns and no visible text or symbols

Ronde kwasten

Close-up of a wooden surface with natural grain patterns and no visible text or symbols

Close-up of a wooden surface with horizontal striations and small white marks (no text or symbols visible)

Oppervlakkige schimmels

After Sales service UBBINK®

Pool 250x450 - H140 cm UrbanPool

Ref: J514009 Later 50/100 Size 300um H 120cm Blue Inner 50/100-365um H 120cm 10.0715924

Nummer dat staat op de verpakkingsdoos

FD FA MGE-D MGI-D B2 MGE-G R MGI-G MSE-1 JD MSE-2 2MSG-CF BR MS-CF P MSI-CF 2MSD-CF PS-1 PS-2 RC-1 RC-2 MRS M1 PJ MRS PA C B1 B2 MPI MSS MEP JAR JA PF R-C1 R-C2 PL ME PRG

Warranty conditions:

• The pool must be assembled within 48 hours after opening the package. However, if you are forced to keep your pool unpacked for an indefinite period of time before installation (e.g. after-sales service request), it is essential to keep all wooden parts flat in a dry and ventilated area, and to restrap them firmly to maintain the benefit of the warranty.
• Assembly of the pool on a flat, smooth, level concrete slab in accordance with the dimensions indicated in the instructions is mandatory for the validation of the warranty.
• Our warranty is limited to the replacement of defective parts. It does not in any way imply a claim for compensation or damage and interest.
• The general warranty does not apply in the following cases:

- Use of equipment not in accordance with our instructions.

- Damage caused by improper handling during and after assembly or any modifications made to structural components without the manufacturer's consent.

The pump:

UNDER WARRANTY

NOT UNDER WARRANTY

- Electrical problem: 2 years under normal use conditions (from the date of purchase of the consumer)

- Deterioration by abrasion or corrosion (particularly in the context of water treatment by salt electrolysis)- Damage due to faulty connection or improper replacement of the cable and/or power plug- Equipment dismantled or reassembled by a third party- Breakage of parts (pump base, prefilter cover, fluted tip...) - use of the dry pump- Damage to the pump due to its immersion (flooding of the technical room for example) - damage due to freezing

The liner:

UNDER WARRANTY

NOT UNDER WARRANTY

- 2-year warranty: Sealing and holding of welds under normal use conditions (from the date of purchase by the consumer)Example of warranty coverage

- Deformations of the liner that has been without water for more than 24 hours (never completely drain your pool) - tasks related to algae growth- Tasks related to the decomposition of foreign bodies in contact with the liner- Stains and discolourations resulting from the action of oxidising products- Colour stability and wear due to friction of the material on various surfaces- Liner tears below the hung rail resulting from liner movement or poor water line maintenance- Holes, snags, tears or cuts- Tasks resulting from overdosing or improper handling of treatment products (poured directly into the water)- Folds or damage resulting from improper installation of the liner

Filtration:

UNDER WARRANTY	NOT UNDER WARRANTY
- 2-year warranty on: tank, drain plug, collar, multi-way valve, pump-filter connection pipe (from the date of purchase of the consumer)	- Leakage problems due to operating pressure exceeding the maximum permissible pressure (see filter instructions)- If sand with grain size less than 0.6 mm is used- Damage or inconvenience resulting from improper assembly or failure to comply with our assembly instructions- frost damage

Wood is a material that remains natural.

Wood is a natural material; it can have imperfections. A number of them are normal and superficial. They are excluded from the warranty because they do not affect the strength and durability of your pool.

Close-up of a textured surface with horizontal dark bands (no visible text or symbols)

Cracks

Close-up of a wooden surface with a small metallic object and a circular hole, no visible text or symbols.

Resin

Close-up of a wooden surface with horizontal grooves and grainy texture (no text or symbols)

Shade differences

A plain beige surface with a single horizontal brown line across the center (no text or symbols)

Longitudinal ribs and knots

Close-up of a wooden surface with visible grain patterns and texture (no text or symbols)

Round knots

Close-up of a wooden surface with natural grain patterns (no text or symbols)

Retention of oven products

Close-up of a wooden surface with horizontal striations and small white marks (no text or symbols visible)

Surface mould

Cracks, splits and tears

Wood is subject to dimensional variations depending on humidity and temperature. When it dries, it retracts irregularly, causing cracks to appear. These can be impressive, but they do not affect the mechanical characteristics and strength of the product.

Resin upwelling

During the autoclave treatment of resinous species, the alternation of vacuum and pressure can lead to sticky resin residues on the surface of the wood. To remove them, simply scratch them gently with a suitable tool.

Colour differences

All wood species have variations in colour. Exposure of wood to UV rays will significantly attenuate them.

Presence of knots

The knots correspond to the trace of the branches of the tree. Our woods are selected to limit the quantity and size as much as possible.

Retention of oven products

Autoclave treated wood often shows greenish or whitish traces on the surface that disappear over time.

Surface mould

Woods are prone to mould caused by microscopic fungi. This surface phenomenon, reinforced by heat, humidity and lack of ventilation, is characterised by spots ranging from light blue to black blue. A simple wiping or exposure of the wood to the outside makes it easy to remove them. It should be remembered that treated woods in class 4 are of course protected against fungal attack.

Additional processing

No additional treatment or application of a wood preservative for your Ubbink® pool is required. When exposed to UV rays, the wood will turn grey over time without affecting its durability. However, you can apply a microporous stain compatible with the autoclave treatment to preserve its original colour if you wish.

Storage and assembly of your pool

If you do not wish to install your pool immediately, it is necessary to store your package properly, without unpacking it, in a cool and well-ventilated place, or failing that, protected from the elements and the sun. If, however, you are forced to unpack your pool, it would be imperative to recondition the package, flat beams, and restrap it firmly. Once unpacked, the structure must be assembled within 48/72 hours.

UNDER WARRANTY

- 15-year warranty against rot and attack by wood-boring insects (from the date of purchase by the consumer) when installed on a smooth, level concrete slab

- Changes in wood colour due to climatic effects- Natural deformations (cracks, splits, and knots that do not affect the mechanical resistance of the wood in any way)- Imperfections that do not affect the solidity of the structure: resin build-up, difference in colour of the beams, retention of proofer products giving the wood a greenish appearance and grey/black surface mould resulting from a lack of ventilation of the packaged structure- Assembly or storage defects resulting in deformation of the wall slats (assembly carried out long after opening the package without restraining)- Deformation of the beams caused by water pressure, which does not alter the mechanical resistance of the pool in any way- Deformation of the structure resulting from non-compliant slab assembly- Deterioration of the structure resulting from semi-underground or non-compliant underground installation (waterproofing sheet and gravel backfill mandatory)- Structural degradation resulting from treatment of the wood with aquaphobic products that do not allow the wood to breathe: tar, varnish, glaze....- Breaks or missing tabs of less than 30 cm that do not affect the mechanical resistance of the pool- Slight deformations that do not prevent the interlocking of the beams

UBBINK® After-Sales Service

Swimming pool 250x450 - H140 cm UrbanPool

IMPORTANT: After-sales service will only be processed with points of sale.

- Mandatory parts to apply the warranty:

√ Checkout ticket/proof of purchase
√ Photo of the damaged part or problem encountered
√ Warranty form below duly completed
√ Serial number

Example of a structural problem:

360 - H200 GB N° 123

No. appearing on notice

1231950

No. appearing on white tarpaulin

Example of a liner problem:

Ref: 7514009 Later 50/100 Size 300um H 120cm Blue Inner 50/100-365um H 120cm 10.0715924

No. appearing on packaging board

Store:	Client:
City:	Address:
Contact:	City:
Direct phone:	Tel:

FD FA MGE-D MGI-D B2 MGE-G R MGI-G MSE-1 JD MSE-2 2MSG-CF BR MS-CF P MSI-CF 2MSD-CF PS-1 PS-2 RC-1 RC-2 MRS M1 PJ MRS PA C B1 B2 MPI MSS MEP JAR JA PF R-C1 R-C2 PL ME PRG

Parts list:

Code	Ref.	Designation	Service Qty	SAV Qty
PL	7100201	Pair of rungs for wooden ladder H120/130 cm	1
M1	7514854	Beam 45 x 145 x 145 x 1310 mm	52
M2	7514855	Beam 45 x 145 x 145 x 1980 mm	14
MSE-1	7514856	Upper beam 45 x 135 x 1310 mm	6
MSE-2	7514857	Upper beam 45 x 135 x 1980 mm	1
MSS	7514871	Upper skimmer beam 45 x 135 x 1980 mm	1
MSI	7514872	Lower skimmer beam 45 x 145 x 1908 mm	1
MS-CF	7514873	Upper counter flow beam + skimmer discharge 45 x 145 x 1980 mm	1
2MSD-CF	7514874	1/2 straight beam swims against the current 45 x 145 x 852.5 mm	1
2MSG-CF	7514875	1/2 left beam swims against the current 45 x 145 x 852.5 mm	1
MSI-CF	7514876	Lower beam swims against the current 45 x 145 x 1980 mm	1
MRC	7514877	Beam with brush socket 45 x 145 x 1310 mm	1
MRS	7514878	Pool spotlight beam 45 x 145 x 145 x 1310 mm	1
PA	7514260	Corner post P1 100x115x1288 mm	4
PJ	7504340	Connecting post P2 100x120x1288 mm	4
B-1	7514879	Notched basting 45 x 170 x 2428 mm	2
B-2	7514880	Notched basting 45 x 170 x 2214 mm	4
BR	7514882	Bottom basting for wall reinforcement 45 x 170 x 1745 mm	2
P	7514881	Reinforcing post 45 x 135 x 1350 mm	4
PS-1	7504346	Galvanised steel support plate 300 x 255 mm	4
PS-2	7504380	Galvanised steel support plate 300 x 255 x 1153 mm	4
R-C1	7514944	Wooden covering, side part 1218 x 145 x 22 mm	8
R-C2	7514945	Wooden covering, central part 1218 x 115 x 22 mm	4
JA	7504347	Corner joint galvanised steel 100 x 1312 mm	4
JAR	7514258	Corner connection reinforcement galvanised steel 119 x 1288 mm	4
JD	7504348	Right-hand connection galvanised steel 118 x 1312 mm	4
PF	7504358	Finishing profile 850 x 60 x 60 x 10 mm	4
PRG	7514889	Galvanised reinforcement profile	2
MEP	7514883	Outer edge small 27 x 145 x 2478 mm	2
MIP	7514884	Small inner edge 27 x 145 x 145 x 2188 int.	2
MGE-D	7514885	Outer edge right 27 x 145 x 2239 mm 45° angle	2
MGE-G	7514886	Outer edge left 27 x 145 x 2239 mm 45° angle	2
MGI-D	7514887	Right inner edge 27 x 145 x 2094 mm 45° angle	2
MGI-G	7514888	Left inner edge 27 x 145 x 2094 mm 45° angle	2
R	7514016	Hung hanging rails 2.06 ml	6
C	7514048	Bracket 45 x 230 x 145 x 170 mm	17
ME	7514052	Step 28x145x600 mm	4
PM	7514114	Martyr piece 45x135x280 mm	2
	7514149	Sand bag (25 kg)	3
	7514750	Stainless steel ladder 3 steps	1

	7504297	Poolmax TP50 pump - 0.37 kw - 0.50 HP - Qmax 12,600 l/h	1
	7514704	PoolFilter Sand filter ø400 mm- flow 17m3/h - 3.5 bar - cap. 50kg - 6 ways	1

Code	Ref.	Designation	Service Qty	SAV Qty
S	7514019	Skimmer wide vent incl. discharge nozzle	1
	7514024	Protective felt pool wall 170gr/m2 - L 1.35 x W 15.3 m	1
	7514822	Floor protection felt for swimming pool 200gr/m2 - L 2.00 x W 5.0 m	1
	7514147	Brush plug assembly for wide and narrow skimmer vents	1
FA	7514758	4-piece aluminium 45d coping stone finishing kit incl. hardware for fixing - rectangular pool	4
FD	7514829	Straight anodised aluminium rectangular pool edge finish	2
	7514753	Set of 2 anchors for rectangular pool ladder support	1

	7514891	Mounting plate for jetstream	1
	7514892	Jetstream housing unit	1
	7514894	Jetstream pump, 2.5HP, 230 V AC~50Hz	1
	7514893	Jetstream control unit	1
	7514896	Urban Pool® electrical box	1
	7504615	Pool spotlight 350 LED Plus	1
	7505523	Heatermax INVERTER 20	1
	7514895	PVC jetstream plumbing kit + Heatermax INVERTER 20	1
	7514208	Plumbing kit	1
	7514302	PVC pipes, ∅ 50 mm, 1 m	8
	7514673	Finishing profile for liner rails (m)	19
	7514129	Hose, 25 m, ∅ 50 mm	1

	7514831	Hardware kit	1
Code	Réf.	DETAIL OF THE KIT QUNCAILLERIE	Service Qty	SAV Qty
A1	7514516	Bracket bag + reinforcements - 6 x 90 Torx screws	3
A3	7514638	Bracket bag + reinforcements - 6 x 90 Torx screws	1
C2	7514639	Rail bag - hung - 4 x 40 screws	1
DMP2	7514618	Bag of coping stone screws - 5 x 50 Torx screws	2
J1	7504411	Bag for fixing posts - bolts + nuts 12 x 160	1
K3	7514847	Bag for fixing posts - bolts + nuts 12 x 120	1
P1	7514273	Metal shoe fixing bag - anchoring studs 20 x 160 + caps	1
P3	7514938	Metal shoe fixing bag - anchoring studs 8 x 90 + caps	1
N	7514275	Wooden ladder bag	1
M	7514276	Fastening bag for wooden cover boards - nails 2.3 x 45	1
T1	7514935	Bag of galvanised reinforcement profile screws - screws 5 x 40 Torx	2

	7514833	Liner 75/100 blue 250 x 450 - H140 cm	1
or
	7514907	Liner 75/100 beige 250 x 450 - H140 cm	1
or
	7514908	Liner 75/100 grey 250 x 450 - H140 cm	1

GARANTÍA DE LAS PISCINAS UBBINK®

Piscina 250x450 - A140 cm UrbanPool

Close-up of a textured surface with horizontal dark bands (no visible text or symbols)

Ranuras

Close-up of a wooden surface with a small metallic object and a circular hole, no visible text or symbols.

Resina

Close-up of a wooden surface with horizontal grooves and grainy texture (no text or symbols)

A plain beige surface with a single horizontal brown line across the center (no text or symbols)

Close-up of a wooden surface with visible grain patterns and texture (no text or symbols)

Nudos redondos

Close-up of a wooden surface with natural grain patterns (no text or symbols)

Close-up of a wooden surface with horizontal striations and small white marks (no text or symbols visible)

FD FA MGE-D MGI-D B2 MGE-G R MGI-G MSE-1 JD MSE-2 2MSG-CF BR MS-CF P MSI-CF 2MSD-CF PS-1 PS-2 RC-1 RC-2 MRS M1 PJ MRS PA C B1 B2 MPI MSS MEP JAR JA PF R-C1 R-C2 PL ME PRG

Lista de piezas:

Close-up of a textured surface with horizontal dark bands (no visible text or symbols)

Fessurazioni

Close-up of a wooden surface with a small metallic object and a circular hole, no visible text or symbols.

Resina

Close-up of a wooden surface with horizontal grooves and grainy texture (no text or symbols)

Discromie

A plain beige surface with a single horizontal brown line across the center (no text or symbols)

Close-up of a wooden surface with natural grain patterns and small dark inclusions (no text or symbols)

Nodi rotondi

Close-up of a wooden surface with natural grain patterns (no text or symbols)

Close-up of a wooden surface with horizontal striations and small white marks (no text or symbols visible)

Muffe superficiali

FD FA MGE-D MGI-D B2 R MGE-G MGI-G MSE-1 JD MSE-2 2MSG-CF BR MS-CF P MSI-CF 2MSD-CF PS-1 PS-2 RC-1 RC-2 MRS M1 PJ MIP C PA MRC MSS MEP B1 MSI MFI PF R-C1 R-C2 PL ME PRG - 28 -

Elenco dei pezzi:

• Dalle Béton - Ep: 200 mm

• Bodenplatte - 200 mm stark

- betonnen - Dikte: 200 mm

• concrete slab - Thickness 200 mm

Architectural diagram of a two-story building with vertical slats and two vertical posts, set against a grassy background (no text or symbols)

• Installation hors-sol (sur dalle béton)
  • Montage auf Grund (auf Betonbodenplatte)
• Bovengrondse installatie (op betonnen bodemplaat)
• Out-of-ground installation (on concrete slab)
• Instalación sobre suelo (en hormigón)
• Installazione fuori terra (su lastra in cemente)

Simple line drawing of a wooden structure with vertical supports and grass at the base (no text or symbols)

• Installation semi-enterrée (sur dalle béton)
  ATTENTION : Dispositif de sécurité obligatoire (bâche, alarme, barrière...)
• Halb versenktes Schwimmbad (auf Betonbodenplatte)
  ACHTUNG: Obligatorische Sicherheitsvorrichtung (Plane, Alarm, Absperrung, ...)
• Halfingebouwde installatie (op betonnen bodemplaat)
  LET OP: veiligheidsvoorziening verplicht (afdekzeil, alarm, hek...)
  • Half-buried installation (on concrete slab)
  NOTE: Compulsory safety equipment (tarpaulin, alarm, barrier...)
• Instalación semienterrada (en hormigón)
  ATENCIÓN: Dispositivo de seguridad obligatorio (toldo, alarma, barrera...)
• Installazione semi-interrata (su lastra in cemente)

Simple line drawing of a flatbed structure with two vertical posts on top, set against a grassy background (no text or symbols)

• Installation enterrée (sur dalle béton)
  ATTENTION : Dispositif de sécurité obligatoire (bâche, alarme, barrière...)
• Eingebautes Schwimmbad (auf Betonbodenplatte)
  ACHTUNG: Obligatorische Sicherheitsvorrichtung (Plane, Alarm, Absperrung, ...)
• Ingebouwde installatie (op betonnen bodemplaat)
  LET OP: veiligheidsvoorziening verplicht (afdekzeil, alarm, hek...)
• In-ground installation (on concrete slab)
  NOTE: Compulsory safety equipment (tarpaulin, alarm, barrier...)
• Instalación enterrada (en hormigón)
  ATENCIÓN: Dispositivo de seguridad obligatorio (toldo, alarma, barrera...)
• Installazione interrata (su lastra in cemente)

3D rendering of a small rectangular enclosure with a tiled roof and arched entrance, set on grassy ground (no text or symbols visible)

3D rendering of a small rectangular enclosure with a tiled roof and arched entrance, set on grassy ground (no text or symbols visible)

3D rendering of a small rectangular enclosure with a tiled roof and arched entrance, set on grassy ground (no text or symbols visible)

• Key points on the partially sunk swimming pool or on the inground installation

Before you begin to assemble the pool, make sure that you have all the necessary parts.

IMPORTANT: If you choose to partially sink your swimming pool, make sure that you embed the pump and the filtration unit at the same level as the pool in an enclosed, waterproof place. To ensure that the filtration unit works efficiently, it must always be positioned below the level of the water.

CAUTION: In the case of a partially sunk swimming pool, before you put any water into the pool, you must have a safety system in place for the prevention of drowning, which complies with your national safety standards

During the excavation phase make sure that the side walls are secured.

3D rendering of a small rectangular enclosure with a tiled roof and arched entrance, set on grassy ground (no text or symbols visible)

1 wooden structure of the pool 2 crushed gravel all around the pool 3 Dimpled sheet HDPE 4 Concrete plate under pool 7504635

• Install the waterproofing sheet (not provided) on the outer sides of the pool to drain off rainwater. The height of the liner must correspond to the level of the bank of gravel.

- The dimpled side is to be placed against the pool structure, leaving an air gap between the wet slope and the pool walls. The dimpled structure provides for a convenient distribution of the slope pressure, und at the same time for a low point load (compresive strength: 250kN / m^2 )

- Fill the pool with water before backfilling the circumference with gravel. Fill the circumference of the pool with gravel. Be careful not to destort the structure when backfilling.

Crushed gravel for drainage Crushed gravel for drainage Anti root tissue Concrete slab Layer of gravel and crushed stone Plastic nubbed membran, HDPE Drainage pipes Natural soil

Wood frame Plastic nubbed membran, HDPE Crushed gravel for drainage Anti root tissue Concrete slab Release film Drainage pipes Layer of gravel and crushed stone ① Wood frame ② Plastic nubbed membran, HDPE ③ Crushed gravel for drainage

3D rendering of a small rectangular enclosure with a tiled roof and arched entrance, set on grassy ground (no text or symbols visible)

3D rendering of a small rectangular enclosure with a tiled roof and arched entrance, set on grassy ground (no text or symbols visible)

Collection of various hand tools including hammers, pliers, screwdriver, and cutting tool (no text or labels visible)

• Hors mise en eau et dalle béton
• Ohne Wasserbefüllung und Bodenplatte
- Aanleg betonnen fundering en vullen niet inbegrepen
- Excluding filling with water and installation of concrete slab
- Fuera de puesta en agua y base de hormigón
- Escluso immersione in acqua e lastra in cemento

3D rendering of a rectangular mechanical component with flanges and mounting holes (no text or symbols)

Illustration of a hand using a hammer to cut a metal structure with a cross mark (no text or symbols)

Illustration of a hand hammering a wooden structure with a hilt (no text or symbols)

• Vous trouverez dans votre colis une pièce de bois à utiliser en intermédiaire entre la masse et les madriers de votre piscine. Celle-ci permet d'éviter l'écrasement des rainures du bois, c'est pourquoi on l'appelle "pièce martyre".
• In der Verpackung finden Sie ein Holzstück, das zwischen den Holzhammer und die Holzbohlen des Schwimmbeckens zu setzen ist, damit die Nuten des Holzes nicht beschädigt werden, deshalb wird es „Schlagholz“ genannt.

• In het geleverde pakket zult u een stuk hout/offerblok vinden dat op de planken van het bad geplaatst moet worden zodra u er met de moker op gaat slaan. Zo wordt voorkomen dat de groeven van het hout beschadigd raken.

• In the package you receive, you will find a piece of wood for using as a protective wedge between the hammer and the planks of your swimming pool. This enables you to avoid crushing the grooves in the wood, which is why it is called a “sacrifice piece”.

• En el embalaje encontrará un trozo de madera que lo pondrá entre el martillo de goma y los tablones de la piscina para no dañar las ranuras de la madera. Por tal razón se le llama “madera protectora contra golpes”.
• Nella vostra scatola troverete un pezzo di legno da utilizzare tra la mazza e le assi della vostra piscina. Ciò permette di evitare lo schiacciamento delle scanalature del legno e per questo motivo viene chiamato “pezzo martire”.

• Comment interpréter cette notice • So ist diese Anleitung zu lesen
• Uitleg bij deze handleiding • How to interpret this notice

• Interpretación de estas instrucciones • Come interpretare il foglietto illustrativo

• Opération de montage à effectuer
  • Durchzuführende Montagearbeiten
  • Te verrichten montagehandeling

• Assembly to be carried out
• Operación de montaje a realizar
• Come effettuare il montaggio

Isometric line drawing of a rectangular industrial or laboratory structure with structural supports and a 15 cm scale indicator (no text or symbols present)

• Sachet quincaillerie à utiliser
• Beutel mit den zu verwendenden Eisenwaren
• Te gebruiken zakje ijzerwaren
• Hardware kit to be used
• Bolsa de tornillería que se ha de utilizar

• Sacchetto degli attrezzi da utilizzare

• Outillage

• Werkzeuge
  • Gereedschap
• Tools
• Herramientas
• Utensileria

SOMMAIRE :

Before starting the assembly, make sure that you have all the necessary parts by taking an inventory from the parts list provided on page 9.

- Installation on concrete slab is mandatory and imperative for warranty validation. Thickness: 20 cm minimum. Make sure that the slab is perfectly flat, smooth and level.

SUMMARY:

1 - Wall assembly	All the instructions in the present operating manual that refer to electrical installations (electrical box, counter-current system, filtration system, swimming pool spotlight and heat pump) must be performed only by a qualified electrician.
2 - Installation of reinforcements and brackets
3 - Preparation of the walls
4 - Installation of bottom felt and liner
5 - Cutting out the jetstream installation
6 - Cutting out the discharge nozzles, brush and skimmer plugs
7 - Cutting and installing the spotlight
8 - Installing the coping stones and anodised aluminium finish
9 - Ladders
10 - Connecting the jetstream system
11 - Connecting the filter system
12 - Connecting the heat pump
13 - Connecting the automatic pool floor vacuum cleaner (The pool vacuum cleaner is optional. It is not included in the equipment provided.)
14 - Electrical cabinet
15 - Using the jetstream installation

Wall assembly

- Align the pool so as to position the entrance of the skimmer(s) facing the prevailing winds in order to optimise the evacuation of surface particles.

Ia - Place the wooden posts in the metal bases. There are short (PS1) and long (PS2) metal bases, make sure they are in the right positions!

Ib - Retrofit the first row of beams. The tabs are intended to correctly align the beams when they are interlocked; their absence or small breaks do not in any way affect the mechanical resistance of the wood, the solidity and the assembly of the pool.

1c - Secure these beams in place using the metal studs (corner and right). Fasten with the bottom bolt 12x160 loosely. Position the assembly of the bolts of the J and K bag: 12 x 160 for the metal bases and 12 x 120 in the upper part of the posts.

Id - Continue assembling the beams using the martyr piece provided for this purpose.

1e - 1f - Place the jetstream beams on rows 6/7/8 in front of the skimmer. Place the lower and upper skimmer beams on the 9/10 rows in front of the jetstream. Place the pool spotlight beam in the 6th row on a wall to the left or right of the skimmer. Place the beam in the 8th row on a wall to the left or right of the skimmer.

Ig - Put the remaining beams in place.

Ih - Check the alignment of the lower and upper skimmer beams as well as those of the jetstream.

Ii - Check the alignment of the shoes (chalk line) and diagonals (10 m tape); A = B

Ij - Tighten all bolts on all posts.

Ik - Prepare the drilling of the upper beams, respecting the dimensions.

II - Drill the central hole (diam. 8 mm), strike the first anchor pin 8 x 90 and tighten. Drill the remaining holes (diam. 20 mm), strike the 20 x 160 anchor bolts and tighten. Repeat the operation on each base.

Im - Nail the finishing boards to the posts. Do the same for RC-1 and RC-2 wood flooring.

Installing reinforcements and brackets

2a - Start by fixing the supplied PRG metal plate below the support boards with the screws. Position the horizontal reinforcements flush with the top edge to the outside of the structure. Level and screw in from inside the pool until the screw heads are drowned.

2b - Pre-drill 3 holes diameter 6 mm (on the corners).

2c - Enlarge the holes to a depth of 45 mm using a 12 mm diameter flat drill bit and screw in using 3 6x90 screws.

2d - Pre-drill 3 holes of diameter 6 mm and screw to the junctions using 3 screws 6x90.

2e - Position the brackets in the up-down direction, draw their positions, drill and screw until the screw heads are drowned.

2f - Screw the horizontal reinforcement with the brackets.es.

Preparation of the walls

3a - Screw the skimmer vent into the upper beam using 2 round head screws to be removed from the screw bag provided in the skimmer box.

3b - Install the skimmer square outer seal and the skimmer body.

3c - Secure the assembly with the 8 round head screws to be removed from the screw bag provided in the skimmer box, tightening effectively for a good waterproofing. (Screw in by hand).

3d - Seals. Place a rectangular joint on the skimmer frame, making sure it adheres well. At the outlet and the brush socket, install the cork seal (A) in contact with the wall and then superimpose one of the 2 white round joints (B), making sure that they adhere well.

3e - Screw the jetstream installation fixing plate fully onto the milléd frame using the 24 4 x 35 mm stainless steel screws provided.

3f - Drill the rails to size (3 cm from the ends and then every 20 cm approximately). The rail of a wall can be composed of several segments placed end to end.

3g - Unroll the wall felt.

Before the next step, carefully clean the concrete slab and remove shards or splinters from the walls with abrasive paper to make all supports clean and smooth.

3h - Attach the plastic rail to the felt underlay of the top plank.

3i - Screw on the first liner rail using the 4x40 stainless steel screws.

3j - At the corners, partially cut into the rail in a "V" shape, so that the profile can be folded. Screw at 3 cm from the corner on both sides, then screw on all the rails.

3k - Cut the felt on the outside of the frame.

31 - Do the same with the return flow, vacuum point and counter-current swimming system frame.

3m - Install the counter-current swimming system body on the mounting plate using the 5x20 stainless steel screws, washers and nuts supplied.

Note: The counter-current system housing must be installed such that the outlet of 75 mm is positioned higher and the suction of 90 mm is positioned lower. 10C page 52.

4 Felt and liner installation

4a - Install the protective felt for the floor.
4b - Cut the protective felt with a cutter or a pair of scissors.
4c - Place the liner in place at an outside temperature between 20 and 25°C.
4d - Match the corners of the liner with the bottom corners of the pool.
4e - Hang the liner in the lip of the rail.
4f - Position the locking ring all around the pool. Start in the middle of the wall.
4g - Stretch the liner to the maximum.
4h - Put in 2 cm of water.
4i - Remove existing folds and fill the pool with water up to 5 cm below the jetstream installation.

5 Cutting the liner and jetstream installation

5a - Install the gasket and jetstream frame using the stainless steel screws provided.
5b - Cut the liner inside the jetstream frame.
5c - Connect the air mixing hose to the front and rear parts of the jetstream box. Insert the hose into the air inlet socket. Secure with a hose clamp. Cut the air hose to the correct length.
5d - Attach the pneumatic hose to the opening provided for this purpose in the jetstream system and connect it to the socket of the PN button (switching the pump on and off). Tighten the hose by hand on the pneumatic switch and on the jetstream housing.
5e - Insert the entire front cover into the jetstream housing and screw in the unit with the 4 stainless steel screws provided.

6 Cutting of discharge nozzle, brush and skimmer socket

6a - Position the discharge nozzle and brush plug from inside the pool.
6b - Cut the liner at the discharge nozzle and brush socket, leaving a gap of about 2 mm. Insert the white seals (B), the nozzle and the brush plug.
6c - Tighten the outer nuts of the discharge nozzle and brush plug sufficiently to ensure tightness by means of the trick, if necessary mentioned on the diagram
6d - Cover the threaded part of the end caps with Teflon tape in a counter-clockwise direction.
6e - Screw the end caps onto the delivery and brush socket.
6f - Example of pipe positioning at the skimmer and brush socket
6g - Brush socket - discharge nozzle Glue the elbow, shut-off valve, corresponding connection and PVC pipes cut to length according to the ground configuration.
6h - Glue the previously assembled assembly to the outlet of the brush socket and discharge nozzle. Close the shut-off valves.
6i - After covering the Teflon threaded part, screw the threaded stop valve into the skimmer body.
6j - Glue the rigid PVC pipe and elbow to the stop valve. Close the valve after the gluing has set and refill the basin to 5 cm below the beams.
6k - Install the gasket and skimmer frame.
6l - Screw the skimmer assembly together using the 18 flat head screws to be removed from the screw bag provided in the skimmer box.
6m - Cut the liner inside the skimmer frame. Finally, place the flange cover by clipping it into place.
6n - Correct water level at mid-height of the skimmer.

7 Mounting the spotlight

7a - Insert the screws into the 4 holes in the front of the assembly frame and slide the silicone gaskets over the screws on the back.
7b - After drilling the liner and beam with a ∅ 25 mm drill bit, screw the assembly frame vertically at a distance of 50 mm to the right or left of the hole, ensuring that the silicone seals are correctly positioned.
7c - Unscrew the fixing nut of the cable bushing and remove it from the cable.
7d - Insert the lamp cable into the liner hole and pull it out. Then carefully push the cable feed-through into the liner hole and push it as far as it will go, making sure that the white seal is in contact with the liner.
7e - Then slide the fixing nut onto the lamp cable and screw it onto the cable feed-through. If you are using a universal wrench or pliers, make sure that you do not overtighten or damage the nut.
7f - Wind the necessary length of cable to pull the spotlight out of the water.
7g - Unscrew the black nut and tighten the cable outside the pool. Position the pool spotlight so that the word «TOP» on the front ring is above and insert the fixing screw into the top hole. Then tighten the lower screw at the bottom of the spotlight.

Be sure to follow the instructions for use given in the instructions accompanying the spotlight.

8 Installation of the pine coping stones.

the coping stone is a finishing element. It is strictly forbidden to walk, run or sit on it. Are not covered by warranty: colour changes, deformations (cracks, fissures, checks, knots or splinters) natural or resulting from improper installation.

8a - Pre-drill the inner coping stones approximately every 70 cm and screw them in. Start at least 3 cm from the ends.
8b - Pre-drill the outer edges.
8c - Screw in the outer coping stones.
8d - Position the corner and straight plates. Pre-drill and screw in using 6x30 screws.

9 Ladders

The use of ladders must be limited to access to the pool

The maximum weight allowed is 150 kg. The pool ladder must be placed in a safe position when not in use..

9a - Retrofit the ladder. To do this, flush the air below the steps if necessary.
9b - Mark the location of the ladder fasteners.
9c - Drill the coping stone and reinforcement with a ∅ 50 mm hole saw. Identify the location of the bracket fixing screws and drill holes.
9d - Place the bracket in the hole and secure with two 6x60 screws
9e - Position the wooden ladder against the horizontal reinforcement below the coping.
9f - Locate and drill the holes.
9g - Mark the locations of each bolt on each of the rungs and drill holes to lock the ladder.

10 Connecting and using the jetstream system

CAUTION!

The electrical connection of the pump and the jetstream control unit must be carried out by a qualified electrician. The power supply must be disconnected with the differential circuit breaker (FI) before any work is carried out on the unit.

10a - Mount the PVC pipes and fittings as shown in the illustration. Note: Before gluing, first proceed with a dry assembly to check that all parts fit together.

• Clean the hose and connecting parts with the paint stripper.
• Do not use abrasive paper to clean the smooth PVC pipe.
  • After cleaning, the surface must be matt. Do not touch the surface again as soon as it has been cleaned.
• Apply the adhesive along the longitudinal axis of the pipe and the connecting pieces.
• Assemble the two parts after applying the glue. Insert the parts fully into each other without turning them and hold them together for a few moments.
• Then remove the excess glue with a brush.
• Do not use the glue at temperatures below 5^ . The assembly must be done quickly.

10b - Connect the pneumatic hose to the electro-pneumatic box. Be careful not to bend the hose.

10c - Connect and fix the air hose to the outer housing of the jetstream using the hose clamp and mount its check valve to the wall outside the pool.

Be sure to follow the instructions for use given in the instructions accompanying the jetstream kit.

• The electrical connection of the filter pump must be made by a qualified electrician.

The power supply must be disconnected with the differential circuit breaker (FI) before any work is carried out on the unit.

I la - Mount the pool filter according to the instructions for use.
IIb - Example of sand filtration installation.

Be sure to follow the instructions for use given in the instructions accompanying the sand filtration kit.

Connecting the heat pump to the sand filtration kit

12a - Mount the PVC pipes and fittings as shown in the illustration. Note: Before gluing, first proceed with a dry assembly to check that all parts fit together.

• Clean the hose and connecting parts with the paint stripper.
• Do not use abrasive paper to clean the smooth PVC pipe.
  • After cleaning, the surface must be matt. Do not touch the surface again as soon as it has been cleaned.
• Apply the adhesive along the longitudinal axis of the pipe and the connecting pieces.
• Assemble the two parts after applying the glue. Insert the parts fully into each other without turning them and hold them together for a few moments.
• Then remove the excess glue with a brush.

12b - Set the by-pass for operation

• For operation with the heat pump: Open valves 1 and 3, close valve 2.
• For operation without the heat pump: Open valve 2, close valves 1 and 3, as shown in diagram 12b on page 54.

Be sure to comply with the operating instructions given in the instructions accompanying the heat pump.

Connection of the automatic bottom vacuum cleaner - the Poolcleaner vacuum cleaner is optional. It is not included in the equipment provided

13a - Insert the pressure regulator into the rubber adapter. Make sure the direction is correct.
13b - Reassemble the automatic brush hose and connect it to the free end of the pressure regulator. It is important to purge it of air. Plug in the assembly kept immersed in the brush socket. Open the shut-off valve of the brush socket and close the one of the skimmer. Switch on the pump. If the brush is not used, close the shut-off valve of the brush socket and open the one of the skimmer. Refer to the automatic broom manual for more details.

Electrical cabinet

CAUTION!

- The installation of the electrical box as well as the connection of the filtration pump, the heat pump, the control unit of the jetstream and the pool lighting must be carried out by a qualified electrician.

- The power supply to the box must be disconnected with the differential circuit breaker (FI) before any work is carried out on the unit.

- The electrical box must not be used as a junction box for connections outside the system.

14a - Have the filter pump, heat pump, jetstream control unit and lighting of the pool connected by a qualified electrician.
14b - Set the analogue timers for the filter pump and pool lighting to the hour by turning the minute hand in the direction of the arrow.
14c - The selection switch on both timers allows you to manually turn the filtration pump and pool lighting on and off or to order them by defining schedules. In the ring area, the times for which you want to set the times are displayed. Push the teeth whose power supply must be cut inwards, the remaining teeth on the outside now represent the time at which the power supply must remain active.

I	Illuminated
	timer
O	Off

In the ring area, the times for which you want to set the times are displayed. Push the teeth whose power supply is to be cut inwards, the remaining teeth on the outside now represent the time at which the power supply is to remain active.

Use of the jetstream installation

CAUTION!

- Only start up the system when the tank is full. It is essential to avoid any dry running of the pump.

15a - Fill the basin with water up to half the maximum skimmer height.
15b - Open both slides and switch on the system with the PN switch
15c - Adjust the water flow by turning the front inner nozzle. The maximum water flow is obtained by turning the nozzle to the left. Turn the nozzle to the right to reduce it.

maximum flow rate

minimum flow rate

15d - Adjust the air addition by turning the front outer nozzle.
15e - Adjust the nozzle to a jet so that the float is opposed to the maximum jet.

Troubleshooting instructions

Problem	Possible cause	Recommended action
The pump makes a lot of noise without providing normal power.	The engine is running in the wrong direction.	Reverse the motor poles by exchanging the phases
	The water level is not high enough.	Add water.
	The pump sucks in air.	Check that the connections do not leak.
	The slide is not fully open.	Open the slide.
	The suction pipe is not watertight.	Seal the suction pipe.
	The pump is blocked (by leaves etc.).	Clean the pump.
The pump makes a lot of noise and provides maximum power.	Friction of the engine cover.	Fix it correctly.
	The fan cover is too loose.	Fix it correctly.
The pump does not start or starts slowly and with difficulty.	A phase is missing.	Modify the power supply.
The FI switch reacts during ignition	Bad fuses	Use a 16A time delay fuse
	Have the installation checked by an electrician.
The engine safety switch turns off.	Incorrect setting.	Set the correct electrical value by +10%.
	The pump overheats.	Allow the engine to cool and restart it.
	A phase has been skipped.	Check the fuse.
The pump cannot be switched on from the tank.	The switch pipe is bent or jammed.	Check that the pump can be switched on from the electrical box.
	Switching hose too long.	Switching hose too short.
	Fuses/power supply/power supply/motor safety switch	Check the fuses/power supply/test the motor safety switch

RESUMEN:

3D rendering of a rectangular structure with horizontal bands and a vertical light beam, no visible text or symbols

PS1 PS2 PS2 PS1 PS1 PS2 PS2 PS1

la PS1(4x)

PS2 (4x)

Simple line drawing of a vertical pole with a triangular base and base plate, no text or symbols present.

Technical line drawing of a structural beam with vertical supports and diagonal braces (no text or symbols)

Isometric line drawing of a rectangular structure with vertical supports and horizontal beams (no text or symbols)

Ic J K

Technical line drawing of a window frame with an angled bracket and directional arrows indicating movement (no text or symbols)

Technical diagram of a structural support frame with labeled components J and K (no text or symbols beyond labels)

Pure mechanical assembly diagram showing two symmetrical components with no text or symbols

OK NO

Isometric line drawing of a rectangular structure with vertical supports and a central horizontal beam (no text or symbols)

Isometric line drawing of a box frame structure with no text or symbols

Illustration of a hand hammering a metal bracket with a havel, no text or symbols present

Isometric line drawing of a rectangular metal fence structure with supports at both ends (no text or symbols)

Isometric line drawing of a rectangular metal structure with horizontal supports and vertical railings (no text or symbols)

Isometric line drawing of a rectangular structure with horizontal slats and supports, mounted on a base platform (no text or symbols)

Isometric line drawing of a rectangular wooden structure with vertical supports and horizontal beams, no text or symbols present

li A B A B

• Contrôler impérativement l'alignement des sabots (cordeau) et les diagonales (ruban 10 m); A = B.
• Unbedingt die Richthilfe der Lagerböcke (Schnur) und die Diagonalen (10 m Band) kontrollieren; A = B.
• Het is noodzakelijk de uitlijning van de keggen (kalklijn) en diagonalen (snoer van 10 meter) te controleren: A = B
• To imperatively check alignment of wedges (chalk line) and diagonals (10 m ribbon); A = B
• Controle siempre el alineamiento de los calzos (cordel) y las diagonales (cinta 10 m); A = B.
• Controllare assolutamente l'allineamento dei ceppi (corde di fissaggio) e le diagonali (nastro 10 m); A = B

lj

Isometric line drawing of a rectangular structure with vertical supports and horizontal beams (no text or symbols)

1k 143 350 350 350 143 143 350 350 350 139 2 cm

Exterior view of a wooden modular structure with support pillars and concrete base, surrounded by grass and shrubs (no signage or text visible)

Technical line drawing of a mechanical device with a tool inserted, mounted on a stand (no text or symbols visible)

Technical diagram of a structural support system with diagonal hatching and a labeled point P (no text or symbols beyond label)

Technical line drawing of a structural bracket with diagonal braces and a base mount (no text or symbols)

Technical line drawing of a mechanical device mounted on a vertical support structure (no text or symbols)

Technical diagram showing a structural support structure with diagonal hatching and a labeled point P (no text or symbols beyond label)

Close-up of a metal structural bracket with bolts and a bolted joint (no text or symbols visible)

Technical line drawing of a structural bracket with diagonal braces and a base plate (no text or symbols)

Technical line drawing of a mechanical assembly with no visible text or symbols

lm PF

R-C2 R-C1

2

• Pose renforts et consoles • Montage der Wandverstärkungen und Konsolen
• Plaatsen van de versterkingsrand en de draagsteunen • Positioning the supports and the brackets
• Colocación de refuerzos y consolas • Posa dei rinforzi e delle mensole

170 2214 2214 2428

3998 (Inner dimension) 1998 (Inner dimension)

Isometric technical diagram of a rectangular structural frame with supports and beams, labeled '2a' and 'A' (no text or symbols on the diagram itself)

Technical line drawing of a mechanical component with grooves and mounting brackets (no text or symbols)

Illustration of a hand using a tool to install or install a wall-mounted component (no text or symbols visible)

2b ≈ 90mm

Worker using a tool to cut wooden beams on a construction site (no visible text or symbols)

2c ≈ 90mm A

2d A

2e 170 mm 230 mm Ø 6 mm 6 x 90 x2 A

Technical diagram of a structural frame with dimension annotations in millimeters

Architectural diagram showing a roof structure with screw fasteners and a labeled section (A), no readable text or symbols present.

Technical line drawing of a wall-mounted device with two rectangular enclosures mounted on a slatted floor (no text or symbols)

3c

Technical line drawing of a mechanical component with mounting flanges and a central rod (no text or symbols)

Close-up of a wooden panel with a rectangular recessed opening, showing wood grain and construction details (no text or symbols visible)

White plastic toilet or sink assembly mounted on a wooden floor, no visible text or symbols

A x2 B

Person installing or repairing a wooden panel on a wooden deck (no visible text or symbols)

Technical diagram of a mechanical assembly with screws and a housing, no visible text or symbols

3f 3cm +20cm 3cm

Architectural cross-section diagram showing layered construction with a cylindrical component and wall-mounted beams (no text or symbols)

Architectural cross-section diagram showing structural layers and a pipe (no text or symbols)

Technical illustration of a mechanical assembly with a hand using a tool, no visible text or symbols

OK NO

Ø 3 mm

3j A 2mm 45° 45° B C

Diagram showing a screw fastening into a bracket (no text or symbols present)

Technical diagram showing a screw fastening into a bracket (no text or symbols)

Isometric line drawing of a two-story building with structural beams and supports, no text or symbols present

Close-up of hands using a power tool on a metal bracket (no visible text or symbols)

Close-up of wooden deck and wall components with a warning triangle icon (no text or symbols)

Diagram showing a 3kx2 layout with a corner frame and a tool, no text or symbols present

Diagram showing a tool interacting with a surface, labeled 'x3' and '31' (no text or symbols on the diagram itself)

Line drawing of a hand using a tool to adjust or install a component on a tablet device (no text or symbols present)

3m

Close-up of hands holding a tool near a white surface, no visible text or symbols

Person installing or maintaining an open electrical outlet wall, no text or symbols visible

• Installation feutre de fond et liner • Installation von Vlies und Schwimmbadfolie
• Aanbrengen van vilt en folie • Installing the felt underlay and the liner
• Instalación del fieltro y del revestimiento • Installazione del feltro e del rivestimento

Diagram of a cylindrical object rolling down a textured surface inside a container (no text or symbols)

Cross-sectional geological or material cross-section diagram with two inset diagrams showing tool illustrations (no text or labels)

4c 20 et 25 °C

Isometric technical diagram of a mechanical or structural assembly with no visible text, numbers, or symbols.

Technical line drawing of a mechanical component or bracket assembly (no text or symbols)

Architectural diagram showing structural components with arrows indicating direction (no text or labels)

Close-up of hands holding a white plastic tube over a curved surface, with no visible text or symbols.

Technical diagram of a mechanical assembly with a cylindrical component inserted into a housing (no text or symbols visible)

Isometric line drawing of a rectangular structure with two hands placed on top, no text or symbols present

Isometric line drawing of a rectangular industrial or laboratory structure with slatted walls and supports (no text or symbols)

4h ± 2cm STOP !

Isometric line drawing of a rectangular structure with internal supports and a wavy interior (no text or symbols)

- Découpe de l'installation de contre-courant • Zuschnitt der Gegenstromanlage • Inpassen van de tegenstroominstallatie • Design of the counter flow system • Ajuste del sistema de contracorriente • Taglio dell'impianto per nuoto controcorrente

Close-up of a hand using a power drill to clean or install a circular metal component (no text or symbols visible)

5a ø 20 ø 18 ø 16 ø 14 ø 12 ø 10 ø 8 ø 6 ø 4 ø 2 ø 0

5b

Circular mechanical component with concentric rings and bolt holes, marked with an arrow pointing to a central hole (no text or symbols)

Close-up of a metallic mechanical component with circular features and a black arrow pointing to a feature (no text or symbols visible)

Close-up of a hand adjusting a small component inside a metallic mechanical housing (no visible text or symbols)

Technical line drawing of a mechanical assembly showing internal components and a separate view (no text or symbols)

Close-up of a white circular electronic device with ventilation slots and a small circular component on the left (no text or symbols visible)

• Découpe buse et skimmer • Zuschnitt der Düse und des Skimmers • Uitsnijden van instroomopening en skimmer
• Cutting the liner and fitting the backwash inlet nozzle and the skimmer • Recorte para tobera y skimmer
• Taglio per condotto e skimmer

Diagram of a threaded mechanical component with directional arrow and label (x2), no readable text or symbols beyond labels

6b x2

Close-up of a hand holding a small metallic object, possibly a tool or component, with no visible text or symbols.

B x2

6c x2

Isometric line drawing of a rectangular industrial or structural housing with pipes and support structures (no text or symbols)

6g Cleanerplug

6h • Pompe • Pumpe • Pomp • Bomba • Pompa

Technical line drawing of a mechanical assembly with a tool and base component (no text or symbols)

6j Pompe Pumpe Pomp Bomba Pompa

6k 5 cm

61

Close-up of hands installing or adjusting a white plastic component on a metal frame (no visible text or symbols)

6m

Diagram showing a vehicle on a road with overhead power lines and a dashed line indicating distance (no text or symbols)

Exterior view of a rectangular recessed light fixture with mounting holes (no text or symbols)

• Découpe et montage du Pool Spot • Zuschnitt und Montage des Pool Spots
• Inpassen en monteren van de poolspot • Design and assembly of the pool spot
• Ajuste y montaje del foco de piscina • Taglio e montaggio del faretto da piscina

Close-up of hands assembling a white plastic mechanical component with a screw (no visible text or symbols)

White plastic mechanical component with mounting holes and a central cutout (no text or symbols visible)

Hand holding a power tool next to an open electrical socket (no text or symbols visible)

Close-up of hands holding a white plastic threaded component against a dark background (no text or symbols visible)

Hand holding a black cable connecting a white plastic bracket (no text or symbols visible)

Hand holding a cable with a connector, no visible text or symbols

Close-up of a white PVC plug inserted into a wooden panel, connected to a black cable (no text or symbols visible)

Close-up of a hand using a power tool to connect a cable on a wooden surface (no text or symbols visible)

Top-down view of a circular electronic device with a black cable wrapped around it, no visible text or symbols.

Close-up of hands installing a black cable on a wooden surface, no text or symbols visible

Close-up of a hand giving a thumbs-up gesture near a wall, no visible text or symbols

Person applying adhesive to a wall, no visible text or symbols

• Installation margelles pins
- Installation der Randplatten aus Kiefernholz
- Aanbrengen van de zwembadrand uit vurenhout
• Installing pine coping
- Instalación de bordes de pino
- Installazione dei bordiin abete

4478 2478

8a 5-8 mm 70 cm DMP

8b Ø4mm 5-8 mm

8c Ø 5 - 50mm DMP

Technical diagram of a structural assembly with diagonal beams and support posts (no text or symbols)

Diagram of a structural joint or connection with layered materials and fasteners (no text or symbols)

Diagram of a double-hinged ladder with three horizontal bars and circular base (no text or symbols)

Line drawing of a hand holding a mechanical component with directional arrows indicating motion (no text or symbols)

Simple line drawing of a hammer and string with a ball, no text or symbols present

PFFF! !

Technical diagram of a ladder assembly with pipes and a valve, no text or symbols present

Technical diagram of a mechanical assembly with pipes and a clamp, no visible text or symbols

9c • MARGELLE RENFORT • VERSTÄRKUNGSRANDPLATTE • BOVENRAND VERSTERKINGSRAND • BORDE DE REFUERZO • BORDO RINFORZO

Technical illustration of a drill bit and screw assembly (no text or symbols)

Diagram showing two circular components with screw holes and a cylindrical component inserted into a rectangular area (no text or symbols)

Close-up of two metallic U-shaped metal railings mounted on a white surface, no text or symbols visible.

Ø 5 - 50 mm N

Technical line drawing of a ladder structure with two arches above it, no text or symbols present

Mechanical switch mechanism diagram with lever and mounting bracket (no text or symbols)

Architectural line drawing of a structural framework with beams and supports (no text or symbols)

Technical diagram of a mechanical assembly with a central shaft and mounting bracket (no text or symbols)

• Raccordement de l'installation de la nage à contre courant • Anschluss der Gegenstromanlage
• Aansluiten van de tegenstroominstallatie • Connection of the counter flow system
• Conexión del sistema de contracorriente • Collegamento dell'impianto per nuovo controcorrente

10a P4 C3 P5 C3 P2 C2 V2 P4 P3 P1 C2 VI P1

Close-up of hands adjusting a small object on a cylindrical device (no visible text or symbols)

Industrial piping system mounted on a wooden wall, no visible text or symbols

10b Control switch

Close-up of a hand adjusting a white plastic pump with a hose and coiled tubing (no visible text or symbols)

Technical line drawing of a mechanical assembly with mounting bracket and wiring (no text or symbols)

M M DM FM C I.N. C ENGINE

S T M DM FM C I.N. C ENGINE

Laboratory apparatus diagram showing a gas cylinder connected to a pump and condenser, with no visible text or labels.

Industrial piping system mounted on a wooden structure, no visible text or symbols

Outdoor industrial equipment setup with pressure vessels and a control unit, no visible text or symbols

graph TD
    A["HeaterMax IN"] --> B["P8"]
    B --> C["PI0"]
    C --> D["T1"]
    D --> E["V3"]
    E --> F["P9"]
    F --> G["PI0"]
    G --> H["T1"]
    H --> I["P10"]
    I --> J["V4"]
    J --> K["P8"]
    K --> L["CI"]
    L --> M["HeaterMax OUT"]
    N["P10"] --> O["C1"]
    O --> P["P9"]
    P --> Q["T1"]
    Q --> R["P10"]
    R --> S["V4"]
    S --> T["P8"]
    T --> U["CI"]
    U --> V["HeaterMax OUT"]
    W["FI"] --> X["Pool IN"]

Mechanical assembly diagram showing a threaded component with a directional arrow indicating motion (no text or symbols)

Technical diagram of a mechanical assembly with directional arrows indicating motion or force (no text or symbols present)

• Coffret électrique • Elektrischer Schaltkasten • Elektrische schakelkast • Electrical control box
• Caja de distribución eléctrica
• Scatola di comando elettrica

14a Contre courant Gegenstrom Tegenstroom Counter Flow Contra la corriente Contro corrente 230V+T 305mm 163mm N L N 1 EADJ TEST FOM-40-000 N 2 Molium Molium D7-30-10 B7-30-10 230V+T Eclairage Beleuchtung Verlichtung Luminaire Illuminación Illuminazione Tension nominale Netzspannung Nominale spanning Power supply Tensión nominal Tensione nominale T N L Pompe à chaleur Wärmepumpe Warmtepomp Heat pump Bomba de calor Pompa di calore T N L Pompe de filtration Filterpumpe Filterpomp Filter pump Bomba de filtración Pompa de filtro Câble Kabel Kabel Cable Cabo Cable 3x2,5mm² (30m max) 230V 3x1,5mm² (30m max) 3x1,5mm² (30m max)

14b 14:21

14c 0 = OFF 1 = ON 1 0 0 = OFF 1 = ON

• Annexe Notice de montage - Kit Plomberie
• Anhang Montageanleitung - Rohrleitungssatz
• Bijlage bij de montagehandleiding - Leidingenset
• Appendix to construction notes - Plumbing kit
• Anexo Instrucciones de montaje - juego de tubeiras

• Allegato Avvertenza di montaggio - Kit impianto idraulico

• Montage skimmer

• Montage des Skimmers
• Montage skimmer
• Skimmer assembly
• Montaje del skimmer
• Montaggio skimmer

Pure mechanical assembly diagram showing a component with a shaft and housing, no text or symbols present

• Montage prise balai • Montage der Saugeraufnahme • Vanne 1/4 de tour • Absperrhahn • Ventiel 1/4 omwenteling • 1/4 turn valve

• Montage prise balai
  • Montage der Saugeraufnahme
  • Montage vuilzuigeraansluiting
• Sweeping attachment assembly
• Montaje de la toma de aspiración
• Montaggio presa spazzola

Pure mechanical pipe connection diagram without any text, numbers, or symbols

• Vanne 1/4 de tour
• Absperrhahn
• Ventiel 1/4 omwenteling
• 1/4-turn valve
• Válvula de corte

• Valvola 1/4 di giro

• Sortie WASTE = Égouts
  • Austritt WASTE = Abwasser

• Uitgang WASTE = afvalwater
• WASTE outflow = sewer
• Salida WASTE = Desagües
  • Uscita WASTE = Scarichi
• Sortie WASTE = Égouts
• Austritt WASTE = Abwasser
• Uitgang WASTE = afvalwater
• WASTE outflow = sewer
• Salida WASTE = Desagües
• Uscita WASTE = Scarichi

• Montage buse de refoulement • Montage der Staudüsen • Montage instroomopening • Delivery nozzle assembly • Montaje de la boquilla de retorno • Montaggio condotti di mandata • Raccordement de l'installation de contre-courant • Montage der Gegenstromanlage • Aansluiten van de warmtepomp • Connection of the counter flow system • Conexión del sistema de contracorriente • Collegamento dell'impianto per nuovo controcorrente • Raccordement de la pompe à chaleur • Montage der Wärmepumpe • Aansluiten van de tegensstroominstallatie • Connection of the heat pump • Conexión de la bomba de calor • Collegamento della pompa di calore

• Montage buse de refoulement
• Montage der Staudüsen
• Montage instroomopening
• Delivery nozzle assembly
• Montaje de la boquilla de retorno
• Montaggio condotti di mandata

UTILISATION ET ENTRETIEN DES PISCINES BOIS

① Failure to comply with the maintenance instructions may lead to serious risks to health, particularly where children are concerned.

1. TREATING THE WATER

Your swimming pool installation is complete! Before you get into the pool for the first time, it is essential to “prepare” the water. Bathing often leads to a good deal of pollution caused by things like vegetation, earth, dust, sweat, saliva, hair, grease, etc. The swimming pool water must be protected from these substances in order to avoid various micro-organisms developing.

In order to do this, a few simple rules may be applied:

- It is a good idea to have the filter running during the day, as it is bathing that causes most of the pollution. Regulate the timing of the filter according to the temperature of the water. The higher the temperature of the water, the more easily bacteria will grow.

Water Temperature	< 10°	10-12°	12-16°	16-24°	24-27°	27-30°
Filtration time	2h	4h	6h	8h	10-12h	-> 20h

Generally speaking, whatever type of system you have, any impurities should be removed if the pool is cleaned regularly using the filter.

The sand filter: When the amount of impurities in the sand increases, the circulation of the water becomes less efficient and consequently the pressure increases. Refer to the notes on maintaining the filtration unit for cleaning it.

• Analyse the water in your swimming pool: it is a worth checking the pH level (degree of acidity or alkalinity of the water) every week. It should always range between 7.2 and 7.6. An incorrect pH level may result in the water treatment products working less efficiently, may accelerate the development of chloramines (causing unpleasant odours and irritation of the mucous membranes...) and the corrosion of any metal parts..
• Treat the water regularly: a weekly disinfectant treatment (bromine, chlorine and active oxygen...) against bacteria will avoid all the problems caused by poor quality water. One treatment every fortnight with an algaecide effectively combats the initial appearance and further development of algae.

① Using and storing chlorinated products

Remember that these are dangerous products that must be stored and used only as directed by the manufacturers. Do not mix chemical products with each other. Store products in tightly closed containers in a cool and well ventilated place; do not expose to direct sunlight. If using a container for measuring out chemicals, rinse thoroughly after each use. Read the safety information and instructions provided on each label carefully. Keep all chemicals out of reach of children..

• Everyday remove as much dirty matter from the pool as possible with a fishing net (fallen leaves, dead insects...) and clean the surface of the water regularly to remove greasy deposits.
• Empty the pump container. Just like the skimmer container, it is a good idea to empty it regularly to maintain the optimum filtration level.

Annual treatment: In order to have clean water all the time, clean the filter, change about to 12 of the water in the pool and look after it properly through the winter. Change all the water in your pool every 3 to 4 years.

Problems and solutions :

PROBLEMS	CAUSES	SOLUTIONS
1. Water clear with greenish or brownish tint.Large number of brown stains on the sides of the pool.	Oxidation of metallic salts (iron or copper) present in the water used to fill the pool	Check the pH level. Put in a calcium and metal stabiliser when you fill the pool. Clean out the filter. Remove sediment and filter continuously.
	pH level too low. Corrosion of metal parts.
2. Water has a yellow or brownish tint	Water being used to fill the pool is high in iron or manganese	See 1.
3. Water milky and cloudy	Organic and colloidal impurities	Chlorinate thoroughly. Clean the filter. Remove sediment and filter well.
	Inorganic substancesincreasing the hardness of the water	Check the pH level. Put in a calcium and metal stabiliser when you fill the pool.
4. Slimy green deposits on the sides of the pool	Build up of algae	Chlorinate thoroughly. Treat with an algaecide
5. Sides of the pool have an uneven appearance	Calcium deposits caused by hard water	Check the pH level. Put in a calcium and metal stabiliser. If the pool is empty clean with a pool descaler.
6. Irritation to skin and eyes, unpleasant odour	Presence of combined chlorine (chloramine)	Adjust the pH level. Chlorinate thoroughly. Put in fresh water
7. Evidence of corrosion	pH level too low	Increase the pH level to 7.0 - 7.4

2. TAKING CARE OF THE STRUCTURE OF THE POOL

- The wood

Wood is a living substance which is subject to variations in humidity and temperature. Over the course of time wood is liable to swell, tiny cracks or splits may appear. Such occurrences do not in any way alter the wood's resistance or the durability of our materials.

Furthermore, a deformity in the sides of the pool caused by the pressure of the water may occur, mainly on the central and lower planks (under maximum water pressure) - this is normal.

On the understanding that the pool has been assembled according to the instructions provided, there is no cause for concern here regarding the stability of the structure.

The sterilising high pressure steam treatment of all the timber parts protects the wood from being attacked by insects and fungi. This treatment gives the timber a greenish hue which does not pose any danger to humans. At any rate, this colour will fade with time. According to how much it is exposed to direct sunlight, the wood will gradually take on a silvery grey appearance. This process can be slowed down by using a glaze or protective oil, which ideally should be applied a few weeks after the swimming pool has been installed (this will stabilise the structure and reduce the greenish tinge caused by the steam treatment...).

- The liner

The liner is a flexible PVC membrane and is exceptionally fragile. Therefore make sure that the water in the swimming pool is absolutely clean and that the pH level is not too high.

• The surface of the water is the most exposed to a variety of deposits so it must be cleaned regularly with the appropriate products (no solvents and no abrasives should be used).
• Never put any undiluted treatment product directly on to the liner as this may cause discoloration. The solid blocks of these products must be dissolved in a chlorine diffuser or ion the skimmer basket.
• When you pause the filtration system, particularly in winter, it is essential to treat the pool to prevent the build up of moss and calcium.

① Never completely drain the pool. You must never allow the liner to be left for more than 24 hours without water in the pool otherwise it may change shape, cracks may appear, etc.

Stains on the liner: causes and solutions

COLORS OF THE SPOTS	POSSIBLE CAUSES	WHAT SHOULD YOU DO
White	1. Discoloration of the material due to contact with a chemical (chlorine...)	1. No solution
White /grey	1. Calcium deposits	1. Drain the pool, have it cleaned by machine, refill the basin, get the water balance right and put in an anti-calcium treatment.
Pink	1. Migration of bacteria which have developed underneath the membrane as a result of an underlying humidity	1) Lower the pH level and the temperature of the water. Carry out a high- power cleaning treatment and run the filter for 48 hours non-stop. To prevent this recurring keep the pH level between 7 and 7.4
Green	1. Algae2. accelerated deterioration of the surface of the water due to sun and oxidising products	1. Correct the pH level, Carry out a high- power cleaning treatment and run the filter for 48 hours non-stop, have the pool cleaned by machine.2. Use a descaler, brush the stains then vacuum the deposits.
Orange/brown	1. Dead algae2. Water contains iron oxide or copper	1. Brush the sides of the pool and vacuum the deposits.2. Lower the pH level and the temperature of the water, brush the stains then vacuum the deposits.
Black	1. Migration of bacteria which have developed underneath the membrane as a result of an underlying humidity 2. Water contains heavy metals (iron, silver ...)	1. Lower the pH level and the temperature of the water. Carry out a high- power cleaning treatment and run the filter for 48 hours non-stop. To prevent this recurring keep the pH level between 6.8 and 7.02. Lower the pH level and the temperature of the water, brush the stains then vacuum the deposits
Liner is sticky or has grease deposits	1. Algae2. Water contains heavy metals (iron, silver ...)	1. Correct the pH level, Carry out a high- power cleaning treatment and run the filter for 48 hours non-stop, have the pool cleaned by machine.2. . Lower the pH level and the temperature of the water, brush the stains then vacuum the deposits

3. WINTER CARE AND SAFETY

Winter care is an essential element of maintaining the pool. The aim of this operation is to avoid the build up of too many algae and calcium deposits inside the basin during the winter. By adding a winter care product you will be protecting the water and your pool in winter, thus making it easier to clean at the start of the new season.

It is imperative that you do not completely drain the pool in the winter (or for a long period of time). In fact totally draining the pool does not improve the condition either of the liner or of the structure of the basin, since the water plays a dual role, providing thermal insulation and ballast. The pool is better protected from weather hasards, the water pressure prevents anything going through the sides of the pool (in case of ground movement) and offsets the pressure of soil and groundwater.

Details about winter care of the filter are given in the notes provided with the tank.

It is a good idea to remove the ladder and put it away in a safe place. For safety reasons, this ladder must only be used for accessing the pool. You should cover the swimming pool with a winter canvas cover or better still a tarpaulin safety cover certified according to safety standard NF P 90 308. In this case you will have to remove any snow from the cover regularly. But having a cover over the pool does not mean that you do not need to be vigilant. You will have to check the state of the water regularly and if the water is turning green you will have to treat it using a chlorine solution.

Finally, make sure that rainwater can drain away properly around the pool.

4. DISMANTLING THE POOL

Whilst it is possible to do so, dismantling the pool is not recommended. In fact, it may cause damage to the component parts and repositioning the liner when reassembling the pool is a very delicate operation.

Exterior view of a modern swimming pool with a wooden deck, surrounded by rocks and trees under a clear blue sky (no signage or text visible)

[e-mail]

(F) Outside Living Industries France SARL

(B) / (L) Outside Living Industries BeLux BVNR

Wondelgemkaai 10

B - 9000 Gent

Assembly Assistance - Only for France - Belgium - Luxembourg

Our assistance service is available from Monday to Saturday from 9am to 6pm, except on public holidays, at the indigo number:

www.outsideliving.com

Ref. 7524451