TVLED32HDP - TV LED POLAROID - Free user manual and instructions

USER MANUAL TVLED32HDP POLAROID

ARS BEEN Rd! 210x140mm

First Time Installation

Please press MENU key to exit

0 Programme Do you want to skip ATV

CDD Please press MENU key to exit

Please press MENU key to exit

SAFETY PRECAUTIONS SAFETY PRECAUTIONS RISK OF ELECTRIC SHOCK DO NOT OPEN The warning sign showing a CAUTION: TO AVOID THE RISK OF The warning sign lightning bolt in a triangle ELECTROCUTION, DO NOT REMOVE THE | showing an exclamation indicates that this product COVER (OR THE BACK OF THE DEVICE). point in a triangle contains “dangerous indicates that this point electrical voltages". NO PARTS ARE REPLACEABLE BY THE of the manual requires USER. PLEASE CONTACT QUALIFIED special attention.

PERSONNEL IN CASE OF FAILURE.

CAUTION: - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR SERIOUS INJURY:

Read these safety instructions before using your device and store them for possible future reference.

This device must only be connected to a mains network whose characteristics are identical to those shown on the device identification plate.

©@The mains plug must always be easily accessible. lt serves as a mains disconnecting switch of the device.

@To disconnect the device from the mains, the plug must be disconnected. Hold the mains cable by its plug. Do not pull on the mains cable to disconnect the plug.

@The mains cables must be routed so that they are not trampled upon or pinched by objects placed on or against them.

@lfthe mains cable of the device is damaged, it must be replaced by the manufacturer, its after-sales service or a similarly qualified person to avoid any danger.

@The device must not be exposed to dripping or splashing water, moisture or liquids.

@Do not place the device near water, for example in a bathroom or near a sink.

@No objects filled with liquids such as vases should be placed on or above the device.

@Never touch the mains cable with wet hands, this could cause a short circuit or electric shock.

@To avoid the risk of fire, do not place sources of open flames, such as lighted candles, or heat sources such as radiators, on or near the device.

@The device is intended for use only in a temperate climate.

@lf smoke, an unusual odour or strange noise is emitted by the device: unplug the

mains cable from the electrical outlet and consult the after-sales service or repair center. Never attempt to make repairs yourself, this could be potentially dangerous.

@Do not attempt to open or disassemble the device. This would expose you to dangerous voltages.

@The slots and openings of the device are intended for ventilation and to ensure its operation. To prevent overheating, these openings must not be obstructed or covered in any way, such as by newspapers, tablecloths or curtains.

@Always leave a minimum distance of 10 cm around the device for sufficient ventilation.

@Never push any object into the device through one of its openings, as it may come into contact with electrical components, which can cause an electric shock or fire.

@ln case of thunderstorm or lightning, immediately unplug the mains cable from the wall outlet.

@Always turn off the device when not in use. Unplug the mains cable from the electrical outlet when the device will not be used for a long period of time.

@Unplug the device from the electrical outlet before cleaning. Do not use liquid or aerosol cleaners. Use a dry, soft cloth for cleaning.

@lfthe product does not bear the [El logo, it is a Class | device. It must then be connected to a mains socket with a protective earth connection.

elfitis a class | appliance, the user's protection is grounded. The appliance must be connected to a power supply base with a connection to the protective earth.

CAUTION -: TO AVOID RISK OF INJURY OR DAMAGE TO THE PRODUCT OR OTHER EQUIPMENT:

eThis product is intended for household and personal use only. Do not use this product for commercial, industrial or other purposes.

@eDo not subject the product to strong shocks, extreme temperatures or direct sunlight for prolonged periods.

@Keep the product away from magnetic objects, motors and transformers.

@Do not use the product outdoors, regardless of weather conditions.

@lnstall the device only on a stand (furniture, wall.…) that can support its weight safely.

@WARNING: never place a TV on an unstable location. This can fall, causing injuries or

even the death of a person. Many injuries, especially in the case of children, can be avoided by taking simple precautions such as:

- The use of furniture or stands recommended by the TV manufacturer.

- The exclusive use of furniture that can support the weight of the TV safely.

- Make sure that the device does not protrude from the edge of the furniture on which itis placed.

- Never place the device on a tall piece of furniture (e.g. cabinets or bookcases) without attaching both the furniture and the device to a suitable stand.

- Do not place the device on a trolley or on a stand that is not stable. Do not install the device on any fabric or other materials placed between its base and the supporting furniture. The device could fall and be damaged or seriously injure à

- Do not use or watch the TV while driving. This is dangerous, and illegal in some countries.

- Explain to children the dangers they face when climbing on the furniture to reach the device or its controls.

- If you keep this device and change the location, you should apply the same considerations.

-__ CAUTION: to avoid accidents, this device must be securely attached to the floor or wall according to the installation instructions.

CAUTION: TO AVOID EYE HAZARDS:

@lt is best to have soft indirect lighting to watch TV. Avoid completely dark environments and any reflection on the screen, as these can cause eyestrain.

À USE AND HANDLING OF BATTERIES:

©@CAUTION: danger of explosion if the batteries are not inserted correctly or if they are replaced by a non-similar or incompatible model.

eReplace the batteries only with batteries of the same type or equivalent type.

Batteries must not be exposed to excessive heat such as that from the sun, fire or similar origin.

@Never throw batteries into fire and never expose them to heat sources.

@Do not mix different types of batteries, or new and used batteries.

The batteries must be inserted according to the polarities indicated on the battery and in the battery case of the remote control.

@Used batteries must be removed from the remote control.

The batteries must be disposed of safely at the assigned specific collection points to preserve the environment. Follow the disposal instructions indicated on the batteries and at the collection points.

©Keep batteries out of the reach of children and animals. Only adults are capable of handling the batteries.

For installation, handling, cleaning and disposal of the device, refer to the following chapters of the user manual.

General Description Specifications and Accessories Overview

External connection Troubleshooting

Picture defects and the reason Warranty conditions

Auto tuning and fine tuning

One mini YPbPr input socket

Two HDMI inputs socket (HDMI 1.4) One mini AV input socket

Support USB One Coaxial output

Wide range voltage input

1. In case of any design change, a notice wil not be released.

Specifications and Accessories

Reference TVLED32HDPRO01

Tuner HD DTV (receives digital channels, satellite, TV guide, teletext

AC 100-240V- 50/60Hz 1.5A Consumption

<65W Dimensions 731.5mm (L)x207.2mm (D)x475.5mm (H) Weight 4.05kg Base Removable, in 2 parts

Operating temperature

0°C to 40°C Remote control power supply 3V —— (2 x LROS/AAA 1.5 V batteries, not supplied)

USB ports with voltage and current | 5V == 0.5A Hotel lock Yes

Speaker Built-in 2xBW Inputs Antennas (T2 and S2), HDMI, Mini YPbPr, Mini AV, USB, CI+ Outputs Coaxial

Functions via USB PVR (digital video recorder)

Multimedia playback formats via

SB Video: MPG, AVI, TS, MOV, MKV, DAT, MP4, VOB Music: MP3, AAC, WMA, M4A Photos: JPEG, BMP, PNG Text: TXT These characteristics are subject to change without notice.

"The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI logo are trademarks of HDMI Licencing LLC in the United

States and other countries.

HIGH DEFINITION MULTIMEDIA INTERFACE ACCESSORIES: Stand 2 pieces Remote control a ne a 1 piece User Guide … nr PIECE confirmation.

PRODUCT DATA SHEET RELATING TO ENERGY Brand POLAROID

felerence Quoi KORSAMLSNAATS 2

Energy efficiency class A+

Visible screen diagonal 80 cm; 31.5 inches

Power consumption in On mode (W) 29W Energy consumption (KWh per year), based on the power consumption of a TV operating four hours a day for three hundred 41 KWniyeer and sixty-five days. The actual consumption depends on the “ conditions of use of the TV.

Power consumption in Standby mode (W) <0.5W Power consumption in Off mode (W) ow Screen resolution (pixels) 1366 x 768

TV Terminal Connections

HDMI/HDMI2: Connect to the HDMI jack of a device with an HDMI output YPbPr: Connect Component video

ANT: Connect to an antenna or cable TV system.

USB: Connect to USB flash driver to play supported multimedia content.

COAX: Connect Coaxial out.

REMOTE CONTROL OUTLOOK & FUNCTION KEY DEFINITION

Turns the television on from the stand-by mode.

(R Button for displaying the source and information about channels.

7. Numerical buttons 0-9

Press 0-9 to directly select a TV channel while watching the TV. In teletext mode enter the page number, etc.

Itis used to enter channel numbers with various digit counts, e.g. for 1- 11-111.

Button for switching to the previously watched channel.

Press in the TV mode to enter/exit the favourites menu.

Switching between the television and radio modes.

Set the automatic shut off time for the television.

Press to show/hide the electronic program guide.

15. A/VI4IDIENTER buttons

Used for navigating in a menu on the screen and for setting up the television according to your preferences.

Function for exiting a menu or a screen.

Press to increase/decrease the volume.

Press to switch between individual channels.

Button of displaying the source and information about channels.

Press to mute the sound. Press it again to renew the sound or press VOL +.

22. HOLDMB-1I button

HOLD button: hold the current display

In the MEDIA mode: Playback/pause or start a time shift recording.

23. REVEAL/44 button

REVEAL button: Press REVEAL to display or

hide hidden teletext information (depends on the broadcast).

SIZE button: Press SIZE to change the size of the screen in the MEDIA mode.

>> button: fast forward.

INDEX button: call up a teletext content page.

m button: Stop recording/playback.

In the MEDIA mode: skip to the previous track

27. S.PAGER>1 button

S.PAGE button: Press S.PAGE to enter a teletext subpage.

B-B1 button: skip to the next track.

Turn teletext on or off.

Note: The teletext function is optional and the availabiliy of buttons depends on the model. Teletext information fully depends on the operator of the channel.

Itis used to start recording with a time shift (i.e. time shift. Function is only available in the DTV mode. 30. AUDIO button

DTV/MEDIA mode: select a background sound, if available.

ATV mode: select a sound mode: Stereo/Dual I Mono.

Other sources: select the leftright channel

Button for showing/hiding subtities in the bottom part ofthe screen, if they are available.

AUTO button: Used for automatic configuration in the PC mode.

REC button: Press Lo start recording. (only in the DTV mode.)

Itis used to enter/exi the PVR setting menu.

Note: Remove battery during storage or when you are not using the device for a long time.

To control the device using the remote control, point the remote control at the device and then press the button with the required function. The maximum range of the remote control is about 5 meters with a deviation of up to +/- 30° from the perpendicular direction to the reception sensor of the remote control on the front side of the device. The falling capacity of the batteries gradually reduces the remote control range. There must be no solid obstacles in the area between the remote control and the device when the remote control is being used.

During standard use the lifetime of batteries in the remote control is about 1 year.

When the effective range of the remote control is substantially reduced, or when there are problems with its use, change both the batteries in the remote control.

If you will not be using the remote control for

a longer period of time, take out both batteries from it - in this way you will prevent potential damage caused by their leakage.

Avoid strong impact of light (e.g. sunlight or light from strong fluorescent/saving sources) which can reduce the effectiveness and reliabilty of IR remote control.

Connecting a TV aerial or satellite dish to your TV To use with a satellite dish (for Freesat or other DVB-S/S2 channels) Connect your dish to the TVS input marked “ANT (S2)-

To use with an aerial (for Freeview, Saorview etc. or other DVB-T2 channels) Connect a TV Aerial to the TVS input marked *ANT (T2).

First Time Installation

When you first turn your TV on you will see the First Time Installation screen, you can also start the first time installation procedure by pressing the menu button and using the 4 buttons to move to the setup menu and then use the W/A buttons to select ‘First Time Installation” and press ENTER.

Select Language Press 4 button to select the language to be used for menus and messages.

Select Country Press W/A button to highlight country menu.

Press 41» button Lo select the country you are in. Press the ENTER button.

First Time Installation

Select Connection Type

Press W/A button to highlight TV Connection menu

Press 4 button to select the type of connection you are using

Antenna for use with a TV antenna (Freeview, Saorviewr etc.)

Satellite for use with a satellite dish (Freesat or other free-to-air satellite TV) Cable for a cable television service.

Set Tune Type to DTV Press the ENTER button.

To use with a satellite dish (DVB-S2 eg. Freesat.)

Load the preset channel database On the “Satellite Auto Tuning Settng' menu leave the Scan Mode set to Normal Scan and press ENTER.

Press 4} button to select the satellite to use, eg. ASTRA 2E, 2F, 26 for the UK Freesat service.

Move down to Scan Mode and use the 4/à button to select Preset.

Move down to Search and press the ENTER button.

When you see the message “Do you want to start Satellite Autoscan" press the left arrow button to confirm. Wait for the Database to be imported, when finished the TV enters viewing mode.

Press ENTER to view the channel list.

Press the GREEN button to select the satellite list, highlight the satellite you wish to view channels for and press ENTER.

To use with an aerial (DVB-T2 eg. Freeview, Saorview etc.)

Wait for tuning to finish and then the TV enters viewing mode. Press ENTER to view the channel list.

Please press MENU key to exit

DTV: Digital TV with an aerial (DVB-T2 eg. Freeview, Saorview etc.)

Cable: For cable TV services outside the UK Satellite: For use with a satellite dish (DVB-S2 eg. Freesat.)

ATV: Analogue TV with an aerial

AV: For connection of a composite video and audio signal to the Mini AV socket. YPbPr: For connection of a component video signal to the Mini Y/Pb/Pr socket. HDMH: For the HDMI 1 socket.

HDMI2: For the HDMI 2 socket.

Media: For playback of media connection to the USB socket on the side of the TV.

1. Press W/A button to highlight the option that you want to adjust in the CHANNEL menu! 2. Press ENTER button to select the highlighted option. 3. After finishing your adjustment, press Menu button to save and return to the previous menu.

To skip ATV tuning and move straight on to DTV tuning, press the MENU button followed by the left arrow Channel Tuning

0 Programme Do you want to skip ATV

tuning? 0 Programme g

= CDD Please press MENU key to exit

Storage to Set the channel number.

Sound System Select the sound system

Colour System Select the colour system (Available System: AUTO, PAL, SECAM)

Fine-Tune Adjust the frequency of the channel finely.

4 ONE Digital First press V/A to highlight the channel you want to select, then:

The three colored keys are shortout keys for programming the channel

Press the Red button to delete the program in the list Press the Yellow button to move the channel in favourite list.

Press the Blue button to skip the selected channel.

Press Fav button to add or remote the channel to your favourite list

(Your TV set will skip between these channels automatically when using CH#/ to view the channels.)

Satellite: Select an available satellite. Channel Type: Select a channel type. Service Type: Select a service type. Scan Mode: Select your scan mode. Unicable: Select Off

Please press MENU key to exit

Press Y/A button to select Satellite Edit then Highlight the satellite to edit and press ENTER. Select press ENTER button to enter. the field to change and the 4/ buttons to change the settings:

1. Press W/A button to select the option that you want to adjust in the PICTURE menu 2. Press ENTER button to adjust. 3. After finishing your adjustment, press MENU button to save and return back to the previous menu

Press Y/A button to select Picture Mode, then press ENTER button to enter sub-menu. Press 4} to cycle through the modes Standard, Dynamic, Mild and User.

Note: You can change the value of contrast, brighiness, saturation, tint and sharpness manually when set to Standard mode.

Contrast/Brightness/Saturation/Sharpness/Tint

Press V/A Button to select option, then press 4 button to adjust

Contrast Adjust the highlight intensity of the picture, but the shadow of the picture is invariable. Brightness Adjust the optical fiber output of the entire picture, it will effect the dark region of the picture. Saturation Adjust the saturation of the colour based on your own like:

Sharpness Adjust the peaking in the detail of the picture.

Tint (NTSC only) Use in compensating color changed with the transmission in the NTSC code.

TIP: In viewing mode you can press PMODE button to cycle through the picture modes quickly.

Color Temp Change the overall color cast of the picture.

Press /A button to select Colour Temperature, then 4 to cycle through the options:

Normal No adjustment

Cold Increase the blue tone for the white. Warm Increase the red color for the white. Aspect Ratio

Manually change the aspect ratio of the picture Press w/A button to select Aspect Ratio, then 4 to cycle through the options: 16:9 (default), Zoomi, Zoom2, Auto, 4:3

Noise Reduction To filter out and reduce image noise and improve picture quality. Press W/A button to select Noise Reduction, then 4 to cycle through the options:

off Select to turn off video noise detection.

Low Detect and reduce low video noise.

Middle Detect and reduce moderate video noise (default). High Detect and reduce enhanced video noise.

1. Press W/A button to select the option that you want to adjust in the SOUND menu 2. Press ENTER button to adjust. 3. After finishing your adjustment, Press ENTER button to save and return lo the previous menu

Press Y/A button to select Sound Mode, then 4/R to cycle through the options: Standard Produces a balanced sound in all environments:

Music Preserves the original sound. Good for musical program: Movie Enhances treble and bass for a rich sound experience. Sports Enhances vocals for sports.

User Select to customise sound settings

Press Y/A button to select option, Press 4 button to adjust

Auto Volume level This reduces the difference between channel and programme volumes automatically. Press Y/A button to select Auto Volume Level, then press 4/2 button to select On or Off

SPDIF Mode Press /A button to select SPDIF Mode, then press 4 button to select Off/PCM/Auto.

AD Switch (Audio Description) Press W/A button to select AD Switch, then press 4

button to select On or Of. AD Volume (Audio Description Volume)

Clock Press Y/A button to select Clock and then press ENTER to open the submenu. Press Y/A button to select each entry, then 4 to adjust the date, month, year, hour and minute.

Off Time The TV will automatically enter standby mode at this time Press Y/A button to select Off Time and then press ENTER to open the submenu.

Press Y/A button to select Off Time and then 4/ to cycle through the options: Once, Every Day, Mon.-Fri. Mon.-Sat., Sat.-Sun., Sunday.

Press V/A button to select Hour, then 4 to adjust the hours. Press /A button to select Minute, then 4 to adjust the minutes.

On Time The TV will automatically turn on from standby mode at this time. Press Y/A button to select Off Time and then press ENTER to open the submenu.

Press Y/A button to select Off Time and then 4/ to cycle through the options: Once, Every Day, Mon.-Fri. Mon.-Sat., Sat.-Sun., Sunday.

Press V/A button to select Hour, then 4 to adjust the hours. Press /A button to select Minute, then 4} to adjust the minutes.

Press Y/A button to select the source, then 4/à to choose the source to turn on. Press V/A button to select Channel, then 4 to select the channel to tune to. Press /A button to select Volume, then 4} to set the volume used when the TV is tumed on

The TV will tum off after the set time has passed

Press W/A button to select Auto Standby, then 4 to cycle through the options: Off, 3 H, 4 H, 5 H The TV will automatically turn off after the preset time if no remote control buttons are pressed. Pressing a button will reset the timer.

Æ select Le ECC Return

OSD Timer Press W/A button to select OSD Timer, then 4 to cycle through the options: 5, 10, 15, 20, 25, 30, Always.

This controls how long the OSD (On Screen Displays) menus will stay on screen after a button is pressed. If set to Always, the OSD will remain on screen until you press the Exit button.

Press MENU button to display the main menu. Press 4} button to select SETUP in the main menu.

OSD Language Select a language for {ne OSD (On Screen Display) menus. The default language is English

Press W/A button to select OSD Language and then ENTER to open the submenu

Press Y/A/4R button to select the language and then Menu to return to the Option menu

Press W/A button to select TT Language, then 4 to cycle through the options: West, East, Russian, Arabic, Persian.

PVR File System Settings for the Personal Video Recorder (PVR) function. A USB device (USB stick/humb drive or hard drive must be connected to the TV, maximum size 1TB formatted in FAT32 or NTFS)

Format Press V/A button to select Format, then press ENTER button to enter sub-menu

This will show you the maximum recording time for SD and HD recordings and allow you to format (wipe clean) the device.

CAUTION: Formatting the device will permanently delete ALL files from the device not just TV recordings.

The Time Shift Size sets how much disk space will be allowed to be used for time shift recordings, ie. how long you can pause or rewind a live recording for.

Press /A button to select Time Shift Size, then press ENTER button to enter sub-menu.

Press the 4/} buttons to adjust the size between:

0GB Time shif is disabled

512 MB SD recording time of 14 min, HD recording time of 4 Min

1GB SD recording time of 28 min, HD recording time of 8 Min

Free Record Limit Press V/A button to select Free Record Limit, then press the 4 buttons to adjust the time for manual recording between 1 and 6 hours.

This will reset the TV to the factory defaults.

Press V/A button to select Reset, then press ENTER button to enter sub-menu. Press t to confirm you want to reset or u to cancel.

HDMI CEC Press V/A button to select HDMI CEC, then press ENTER button to enter the sub-menu.

HDMI CEC Press 4 button to turn the CEC Control on or off.

HDMI ARC Press 4/à button to turn the Audio Receiver Control on or off. Auto Standby Press 4/à button to turn the Device Auto Standby on or of. Auto TV On Press 4/à button to turn the Auto TV Power On on or off. Device control Press 4/à button to turn the Device control on or off.

Device List Press ENTER button to show list of device.

First Time Installation This allows you to restart the first time installation process. Press V/A button to select First time installation, then press ENTER button to start

Blue Screen When turned on, the screen will be blue if there is no signal, if turned off, the screen will be black. Press button to select Blue Screen, then press the 4/ buttons to select On or Of.

1. Press W/A button to select the option that you want to adjust in the LOCK SYSTEM menu. 2. Press ENTER/4/R button to adjust 3. After finishing your adjustment, press MENU button to return back to the previous menu

Press V/A button to select Set Password, then press ENTER button to enter sub-menu to set new password

Channel Lock Press V/A button to select Channel Lock, then press ENTER button to enter sub-menu to select. Press Green button to lock or unlock the channel

Parental Guidance Press V/A button to select Parental Guidance, then press the 4/ buttons to select the one that is suitable for your children.

Key Lock Press W/A button to select Key Lock, then press 4/à button to select Off or On. When Key Lock is turned on the buttons on the rear of the TV are disabled

1. Press W/A button on the remote control to select hotel mode in the Lock menu. 2. Press ENTER button on the remote control to enter the Sub-menu. 3. After finishing your adjustment, press MENU button to save and return back to the previous menu

Hotel Mode Press V/A button to select Hotel Mode, then press 4 button to select on or off.

Source Lock Press Y/A button to select Source Lock, then press ENTER button to enter sub-menu to select.

EPG Press EPG button on remote control to enter EPG menu page.

7 Day TV GUDE Press W/A navigation buttons to select preferred program: Press 41 navigation buttons to switch between left column and right column

When a program is highlighted Press RED button to record program.

Press GREEN button display information on the highlighted program. Press YELLOW button to recording schedule.

Press BLUE button to set a reminder. Favourite List

FAVOURITE LIST When viewing a channel, press the FAV button on the remote control to enter the Favorite List menu

79 Bec NEWS HD Press W/A navigation buttons to select your preferred channel Press ENTER button to confirm the selection. NOTE:

To add a favourite channel, please refer to the operations of*DTV Mode > Channel > Programme Edit”

Quick select When viewing an available channel, press ENTER button on remote control to enter Channel List menu page.

Press w/A navigation buttons to select preferred channel. 4 Gnanneï 4 Press 4 navigation buttons to select a channel group. É = > Press ENTER button to confirm the selection Tirvs 8 ex save

USB Note: Before operating Media menu, plug in USB device, then press INPUT button to set the Input Source to Media.

Press V/A button to select Media in the Source menu, then press ENTER button lo enter.

Press 4 button to select the option you want to adjust in the main Media menu, then press ENTER button to enter.

button to select PHOTO in the main menu, then press ENTER button to enter.

Press Exit button to retum to the previous menu and exit menu to quit.

Press 4} button to select the file you want to watch in the file selecting menu, then press media button to display picture.

When highlighting the option you select, the file information wi appear on the right and picture will be previewed in the center.

Press Exit button to retum to the previous menu and exit menu to quit.

Press 4 button to select MOVIE in the main menu, then press ENTER button to enter.

Press Exit button to retum to the previous menu and exit menu to quit.

Press 4} button to select drive disk you want to watch, then press ENTER button to enter.

Press media button to play the selected movie

Press display button to select menu in the bottom you want to run, then press ENTER button to operate. Press Exit button to back to the previous menu and exit button to quit the entire menu.

Press 4/> button to select TEXT in the main menu, then press Enter button to enter.

Press Exit button to retum to the previous menu and exit menu to quit.

Press 4/> button to select drive disk you want to watch, then press Enter button to enter.

Press 4/> button to select return option to back to the previous menu:

1. Assemble the stand

Before attaching/detaching the stand, make sure to turn off the TV.

-_ Before performing work spread cushioning over the base area to lay the LED TV on. This will prevent it from being damaged

Stand installation instruction

If you have any problem, check the couter measures for each symptom listed below. The following symptoms may have been caused by inappropriate adjustment rather than actual malfunction of the unit. f the trouble persists, contact the Customer Care Centre, see back page for contact details.

Symptoms Possible solutions

Please check the power cord plugged in and that the power outlet works.

No power Unplug the power cord and plug it in after 60 seconds and restart the TV.

Please check antenna connection. No picture Station may be experiencing problems, please tune to another station. Please adjust the settings of contrast and brighiness.

Please increase the volume. Please check TV is under mute mode, press MUTE button on the remote control. Please check sound settings

If external devices are being used, check their volumes are not set 100 low or tumed Good picture but of.

nosound If using AVI or Component inputs, please make sure cables are connected properly

and not loose. If using DVI to HDMI cable, a separate audio cable is required. Make sure a headphone jack is not connected.

Good sound but Please check antenna connection and antenna condition. If using Component input, abnormal color or | please check Component connections, incorrect or loose connections may cause no picture colour problems or cause the screen to be blank.

Batteries of remote control may have exhausted, if necessary, please change the batteries.

Clean the remote control lens. The distance between LED TV and remote control should be within 8m, within recommended operating angle and path is free of obstructions.

No response to remote control

Although the LED screen is made with high-precision technology and 99.99% or more Colored dots may be | of the pixels are effective, black dots may appear or bright points of light (red, blue, or present on the screen | green) may appear constantly on the LED screen. This is a structural property of the LED screen and not a malfunction.

Keep the TV away from noïsy electrical sources such as cars, hair dryers, welders, and all optional equipment.

Electrical atmospheric interference such as local or distant lighining storms may cause picture to break up.

When installing optional equipment, leave some space between the optional equipment and the TV.

Check the antenna and connection:

Keep the antenna away from any power or input/output cables.

Picture is breaking up

Check your area is covered by Digital Video Broadcasts. Try re-tuning or manually

After Auto Tuning only Some channels are > |'Uning missing channels. Salt Check that you are using the correct antenna type - please see pg. 16 ‘Antenna

Check if the channel has been blocked in the main menu settings. selected

Please check connecting USB cable and power supply is connected. Hard drive has USB not playing not been formatted. Please make sure USB disk is compatible and the multimedia data formats are supported.

Picture is distorted, macroblock, Compression of video contents may cause distortion especially on fast moving small block, dots, pictures such as sports and action movies.

Check cable connections, make sure a video cable is not connected to an audio input.

Noise from speaker | Lu cional level may cause sound distortion.

Check if the Off Timer or Sleep timer is turned on. automatically

Check if the On Timer is set to On in the Setup menu. automatically

Picture is not shown | First check if it is caused by the input signal. Then try to adjust Zoom in Function in full screen menu.

Picture defects and the reason

Snowy picture is usually due to weak signal. Adjust antenna or install an antenna amplifier.

Double Image or Ghosts

Double images are usually caused by reflections from tall buildings. Adjust the direction of the antenna or raise it.

Ghosting may also occur when stil pictures are displayed continuousiy. It may disappear after a few moments.

Radio Wave Interference

Wave patterns are moving on the screen, which are usually caused by nearby radio transmitters or short-wave receiving equipment.

High Temperature Electrothermal Interference

5 Diagonal or herringbone patterns appear on the screen or part of picture is missing. This is probably caused by high temperature electrothermal equipment in a nearby hospital.

OPERATING MANAGEMENT:

Your product is guaranteed 2 years.

To request support, contact the customer service at 0811 482 202.

You wil then be asked the defective part and the original invoice stating the product regulation. We may ask you for photos of your appliance.

FAILURE TO PACKING: Ii appeared, after unpacking the product or device, a vice preventing the use of the product in its expected configuration, contact the customer service within 72 hours worked.

DISCLAIMER OF WARRANTY DISCLAIMER OF WARRANTY RELATED TO THE ORIGIN OF DAMAGES The guarantee does not apply in case of accidental physical damage, it does not cover such damage and failures that resulted:

+ improper installation (of a bad installation) or a misuse or poor maintenance of {he product

© improper use of the material or not complying with the instructions in the user manual.

© lighining, flood, fre, power surge, shock, poor ventilation, a fall, discoloration due to the action of light,

burning, humidity, excessive heating without humidifier, or irregular ground or insects.

+ repairs made and/or working on the hardware and/or opening of it by an unauthorized person by the manufacturer.

© maintenance, repair or replacement of parts due to normal usury or failure to maintain.

© modification of the construction and original features of the guaranteed product.

+ corrosion, oxidation, a bad connection nor an external power supply problem.

EXCLUSION OF WARRANTIES RELATING TO THE NATURE OF DAMAGES (INDIRECTS DAMAGES)

The guarantee covers only the right to repair or replace the guaranteed product. Consequently, the indirect

damage resulting from the failure or damage not covered by warranty, including:

© Commissioning costs, adjusting, cleaning:

+ Damage of any kind resulting from the unavaïlabiity of the product guaranteed during the period between deterioration and failure and repair or the replacement of the product guaranteed.

+ Damage and faults under specific exclusions in the warranty manufacture guaranteed product, as mentioned in the product instructions for use;

The aæesthetic damage:

e The products guarantee that the customer is not able to return or those who returned without their accessories.

© In accordance with the ISO 13406-2 norm, a product is considered defective when the number of dead or lit pixels is over 3.

SUPPORT Please refer you to the board below to find easily your alter sales number: COUNTRY PHONE NUMBER EMAIL WE FR || E www.mms-support.net (only for metopdtan | ("2270811 482 202 | sav@polaroic-France com nu polradiech France)

« Di — +352.26.11.00.90 | support BE@market-maker.fr

LL] DE == +49359127224626 | Service@letmerepair.com IT [| || 199 309 314 helpdesk@stitaly.it ES (ras) + 3495217094 79 | support_ES@market-maker.r PT Es (+34) 952 179 557 info@letmerepair.pt cH E3 0900 77 88 99 info@dstv.ch

Declaration of conformity El Market Maker Brand Licensing, hereby declares that this equipment, conforms to the essential requirements and other relevant provisions of Directive 2014/53/UE. The declaration of Conformity can be viewed al the following address:

http:/wmww.mms-support.netOTA/ECD_MMBL_TVLED32HDPRO01.pdf

E PLR IP Holdings, LLC, ils licensees and affliates, fully support all electronic waste initiatives. As responsible stewards of the environment, and to avoid violating established laws, you should properly dispose of this product in compliance with all applicable regulations, directives or other govemances in the area where you reside. Please check with local authorities or the retailer where you purchased this product to determine a location where you can appropriately dispose of the product.

THE DISPOSAL OF ELECTRICAL AND ELECTRONIC EQUIPMENT WASTE PRODUCTS ON THE PART OF FINAL USERS IN THE EUROPEAN UNION This symbol on the product or on the container indicates that this product cannot be eliminated with the general waste. The user is responsible for eliminating this kind of waste by throwing them away at a "recycling point" specifically for electrical and electronic waste. Selective collection and electrical equipment recycling contribute to preserve natural resources and warrant waste recycling to protect environment and health. In order to receive further information about electrical and electronic waste collecting and recycling, contact your Local Council, the service of household waste or the establishment where the product was acquired.

Polaroid, Polaroid & Pixel, Polaroid Classic Border Logo and

Instantiy recognizable. Instantiy Polaroïd Color Spectrum are trademarks of PLR IP Holdings. reassuring. The Polaroid Classic LLC, used under license. PLR IP Holdings, LLC does not Border lets you know youve manufacture this product or provide any Manufacturer's

purchased a product that exemplifes ‘he best qualies of our brand and Warranty or support. that contibutes to our rich heritage of www.polaroid.tech

alt and Innovat ‘quel and Innovation: Market Maker Brand Licensing - 79/81 Ancienne Route

© 2019. Al Rights Reserved Nationale 7-69570 Dardilly, France

Questions? ? : Hyou sut have que Need some help? call our help line: à This manual al el 0811 482 202 wuwpolaroid.tech

First Time Installation

Please press MENU key to exit

0 Programme Do you want to skip ATV

= CL Please press MENU key to exit

Please press MENU key to exit

First Time Installation

Please press MENU key to exit

TV: 0 Programme DTV : 0 Programme Radio : 0 Programme Do you want to skip ATV

tuning? Data : 0 Programme

CDD Please press MENU key to exit

Please press MENU key to exit

Press < to confirm you want to reset or » to cancel.

731,5mm (L)x207,2mm (D)x475,5mm (A)

Please press MENU key to exit

0 Programme Do you want to skip ATV

= CL Please press MENU key to exit

Please press MENU key to exit

First Time Installation

Please press MENU key to exit

= CL Please press MENU key to exit

ATV handmatig afstemmen

Do you want to skip ATV tuning?

Please press MENU key to exit