32 - LED TV POLAROID - Free user manual and instructions

USER MANUAL 32 POLAROID

MPORTANT INSTRUCTIONS SAFETY PRECAUTIONS Read these safety instructions before using your device and store them for possible future reference. CAUTION

The warning sign showing a | ELECTROCUTION, DO NOT REMOVE THE | he warning sign showing lightning boit in a triangle | COVER (OR THE BACK OF THE DEVICE). | an exclamation point in a indicates that this product | NO PARTS ARE REPLACEABLE BY THE | triangle indicates that this contains "dangerous USER. PLEASE CONTACT QUALIFIED | point of the manual requires electrical voltages". PERSONNEL IN CASE OF FAILURE. special attention. ÂÀ CAUTION: - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR SERIOUS INJURY: Read these safety instructions before using your device and store them for possible future reference. < This device must only be connected to a mains network whose characteristics are identical to those shown on the device identification plate. < The mains plug must always be easily accessible. It serves as a mains disconnecting switch of the device. + To disconnect the device from the mains, the plug must be disconnected. Hold the mains cable by its plug. Do not pull on the mains cable to disconnect the plug. < The mains cables must be routed so that they are not trampled upon or pinched by objects placed on or against them. e Ifthe mains cable of the device is damaged, it must be replaced by the manufacturer, its after-sales service or a similarly qualified person to avoid any danger. < The device must not be exposed to dripping or splashing water, moisture or liquids. + Do not place the device near water, for example in a bathroom or near a sink. + No objects filled with liquids such as vases should be placed on or above the device. + Never touch the mains cable with wet hands, this could cause a short circuit or electric shock. e To avoid the risk of fire, do not place sources of open flames, such as lighted candles, or heat sources such as radiators, on or near the device. + The device is intended for use only in a temperate climate. e If smoke, an unusual odour or strange noise is emitted by the device: unplug the mains cable from the electrical outlet and consult the after-sales service or repair centre. Never attempt to make repairs yourself, this could be potentially dangerous. + Do not attempt to open or disassemble the device. This would expose you to dangerous voltages. + The slots and openings of the device are intended for ventilation and to ensure its operation. To prevent overheating, these openings must not be obstructed or covered in any way, such as by newspapers, tablecloths or curtains.

MPORTANT INSTRUCTIO| e Always leave a minimum distance of 10 cm around the device for sufficient ventilation. e Never push any object into the device through one of its openings, as it may come into contact with electrical components, which can cause an electric shock or fire. e In case of thunderstorm or lightning, immediately unplug the mains cable from the wall outlet. e Always turn off the device when not in use. Unplug the mains cable from the electrical outlet when the device will not be used for a long period of time. e Unplug the device from the electrical outlet before cleaning. Do not use liquid or aerosol cleaners. Use a dry, soft cloth for cleaning. e lfthe product does not bear the [E logo, it is a Class | device. It must then be connected to a mains socket with a protective earth connection. ÂÀ CAUTION -: TO AVOID RISK OF INJURY OR DAMAGE TO THE PRODUCT OR OTHER EQUIPMENT: e This product is intended for household and personal use only. Do not use this product for commercial, industrial or other purposes. e Do not subject the product to strong shocks, extreme temperatures or direct sunlight for prolonged periods. e Keep the product away from magnetic objects, motors and transformers. e Do not use the product outdoors, regardless of weather conditions. Install the device only on a stand (furniture, wall.) that can support its weight safely. + WARNING: never place a TV on an unstable location. This can fall, causing injuries or even the death of a person. Many injuries, especially in the case of children, can be avoided by taking simple precautions such as: -The use of furniture or stands recommended by the TV manufacturer. -The exclusive use of furniture that can support the weight of the TV safely. -Make sure that the device does not protrude from the edge of the furniture on which it is placed. -Never place the device on a tall piece of furniture (e.g. cabinets or bookcases) without attaching both the furniture and the device to a suitable stand. -Do not place the device on a trolley or on a stand that is not stable. Do not install the device on any fabric or other materials placed between its base and the supporting furniture. The device could fall and be damaged or seriously injure a person. -Do not use or watch the TV while driving. This is dangerous, and illegal in some countries. -Explain to children the dangers they face when climbing on the furniture to reach the device or its controls. -lf you keep this device and change the location, you should apply the same considerations. -CAUTION: to avoid accidents, this device must be securely attached to the floor or wall according to the installation instructions. ÂÀ CAUTION: TO AVOID EYE HAZARDS: e Itis best to have soft indirect lighting to watch TV. Avoid completely dark environments and any reflection on the screen, as these can cause eyestrain.

MPORTANT INSTRUCTIONS ÂA USE AND HANDLING OF BATTERIES: e CAUTION: danger of explosion if the batteries are not inserted correctly or if they are replaced by a non-similar or incompatible model. e Replace the batteries only with batteries of the same type or equivalent type. e Batteries must not be exposed to excessive heat such as that from the sun, fire or similar origin. e Never throw batteries into fire and never expose them to heat sources. e Do not mix different types of batteries, or new and used batteries. e The batteries must be inserted according to the polarities indicated on the battery and in the battery case of the remote control. + Used batteries must be removed from the remote control. e The batteries must be disposed of safely at the assigned specific collection points to preserve the environment. Follow the disposal instructions indicated on the batteries and at the collection points. e Keep batteries out of the reach of children and animals. Only adults are capable of handling the batteries. For installation, handling, cleaning and disposal of the device, refer to the following chapters of the user manual.

Table of Contents Accessories. Introduction. Features- Basic Function. Specifications: Stand and wall-mounting instructions (optional) General Description Overview of front panel Overview of back panel Overview of remote control: Installing Batteries in the Remote Control: External Connection Antenna connection Connecting VCR Connecting a Camcorder Connecting DVD Player/Set-Top Box via HDMI Connecting Dightal Audio System Connecting PC Supporing Signals Basic Operation Menu Operation Picture Sound Setting Lock PVR Option. Program Network About Home Operation SOURCE setup APP setup SETTING setup Digital Media Player Troubleshooting Warranty conditions

Accessories Please make sure the following items are included with your LED TV. If any items are missing, contact your dealer. Owner's Remote Control Instructions

DVB-C: 113MHz-898MHz DVB-S/S2: 950MHz-2150MHz Video in PALINTSCISECAM Power consumption 55w Standby comsumption <1W Antenna input 75 ohms, unbalanced Controller power DC 3v (Two AAA size batteries) Dimensions |TV with stand (DWXH) TV without stand 731.8x184.5%475.2mm 731.8*x87.3*x435.1mm Weight TV with stand 43Kg (Net weight) TV without stand 4.23Kg Work temperature 0°C-40°C NOTES: + Design and specifications are subject to change without notice. + Weight and Dimension shown are approximate.

duc: Spec sheet about energy Brand Polaroid TVSHD32PR001 Reference (Model: KDL32MO662ANTS) Energy efficiency grade A+ Screen size 80 cm; 31,5 inch Eletrical consumption in on mode (W) 32W Annual electric consumption for 4 hours/day, 365 days/year 47 kWh/annum Eletrical consumption in sleep mode (W) <1W Eletrical consumption in off mode {W) ow Screen resolution (pixels) 1366 x 768 Specifications are subject to change without notice. $Polaroid nano

KWh/annum 2[p°) HOMI ET Da TOM LA TRE NAS INT PAC 2mopoe 2520 The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. To avoid possible hearing damage, do not listen at high audio volume for long periods of time.

How to assemble the stand If you need to remove or assemble the stand please read the following instructions. -Before attaching/detaching the stand, make sure to turn off the TV. -Before performing work, spread cushioning over the base area to lay the LED TV on. This will prevent it from being damaged. Assembling instructio Step1: Take out two stands from package, and insert them into bottom of TV: Step2: Take out four screws provided with TV set and tighten them into screw holes: g instructions (op 4 screws for 32" model - To disconnect the stand from the TV, perform the above steps in reverse order. Wall mounting instructions (optional) Your LED TV is able to accommodate wall mounting with the use of a wall mount bracket (not supplied with LED TV, please contact your local hardware store) and the mounting holes on the back of the unit. We recommend removing the TV stand prior to wall mounting the TV. Please see previous page for instructions on removing the stand.

3. Wall-mounting bracket(one)

4.Self-tapping screw(three)

5. Wall-mounting screw M4/M6

wo for each(Only need to select two)

Wall-mounting instruction:

1. The wall-mounting bracket is suit for 23 to 43-inch flat TV that the wall-mouting hole

distance is 100 or 200mm.(The wall-mounting hole of back panel should be smooth.)

2. Punch three holes on the wall according to the wall-mounting bracket (3)

3. Insert the nylon anchors(2) into the corresponding holes on the wall.

4. Fix the wall-mounting bracket (3) with self-tapping screws(4) in nylon anchors of the wall.

5. Screw the wall-mounting screws(5) into the upper two screw holes in the back panel.

6. Left the TV and hang it on the wall by two people.

1. Please mount your TV on the strength of the wall for withstanding the TV’s weight.

2. Be careful not to scratch panel and TV cabinet when your fasten the screws on the

General Description Overview of front panel The buttons on the lower-left panel control your TV's basic features, including the on-screen menu. To use the more advanced features, you must use the remote control. The control panel Press this button on the control panel one time as CONFIRM at any menu © 0 Centre Press and hold this button to display FUNCTION menu at any menu Press and hold this button to turn on TV when it is in standby mode. etu Push one time: Use to select menu item if menu on TV. Use to go to last channel P when watching TV. Push one time: Use to select the next menu item if menu on TV. Use to go to next © ! Down channel when watching TV. Push and hold this button to return to the last page. Push one time: Use to select the left menu item if menu on TV. Use to decrease © — Left olume when watching TV. © — Right Push one time: Use to select the right menu item if menu on TV. Use to increase volume when watching TV. 6 Remote control sensor / Power indicator Note: The product and illustrations in this user's manual is only for explanation purposes and may vary depending on model.

General Description You can connect the TV with video devices such as DVD/VCD player, VCR and video camera to enjoy the high quality picture.

USB —— PF | 0 0@ OPTIQUE Camcorder DVD player PC (HDMi-output)

Blu-ray disc player Note: The product and illustrations in this user's manual is only for explanation purposes and may vary depending on model.

1) Remove the lid of the battery compartiment.

2) Insert 2 size AAA batteries with polarities as indicated inside the compartment.

1) A loading of batteries should be last one year under normal use.

2) If you don't intend to use the remote control for a long period of time, remove batteries

to avoid damage due to leakage.

3) Do not mix old and new batteries or different types.

4) Do not throw batteries into fire or water.

5) The batteries (battery pack or batteries installed) should not be exposed to excessive

heat such as sunshine, fire or the like.

1. POWER: Turn the TV on and off.

2. INPUT: This button is used to switch among different

sources, Select a source and press ENTER button to confirm.

4. RECALL: Switch to the previous program.

6. INFO: Display the program information.

7. SUBTITLE: In DTV source, the button is used for subtite.

language. In USB source, the button is used to change subtitle.

8. HOME: Press it to go to App home page.

9. NETFLIX: If network connects, press this key to view

12. ENTER/LIST: Press to show channel list and favorite list

on screen. 96880896 66 © 66000

16. COLOR BUTTONS: If's used in APPS.

17. MUTE: Press this button to cut off the sound of the TV

set temporarily, press again to resume. 18.1/11 button/AUDIO LANG : In ATV source, the button is used to set NICAM sound system. In DTV source, the button is used to set the audio language.

General Description Overview of Remote Control

21. DIGITAL MEDIA PLAYER CONTROL BUTTON:

Include play/pause, stop, previous, next, backward, C1] forward is used in USB mode Please refer to relevant instructions in the section of multimedia player.

22.NDEX(»/1): Press INDEX button, then index page displays. It is also used for time shifting function when TVis on DTV mode, please refer to PVR page. 6 ro 23.MIX ( e }: Teletext buttons for mix function, please refer (7) us to TTX description page. It is also used for recording TR function when TV is on DTV mode, please refer to PVR © page. © [2]

24. HOLD:Press HOLD button to toggle Hold function on

or off. When Hold is switched on, the page acquisition is stopped. When Hold is switched off, the page acquisition is started @

half of the screen in double height, press the SIZE button @ two times to display the lower half of the screen in double height, press three times to display the full screen in normal size.

27. REVEAL: Pressing this button will reveal any hidden

data (answers to quizzes for example). Press the REVEAL button again to return to normal screen. 98600086 66 © 6000

28. TIME: This button is used to show the time of the teletext. CRÈTE]

29. SUBCODE: Subcode mode gives the possibility to select

certain subcode pages of a Teletext page. Entry of digits within the range 0... for current subcode entry. If the digit completes the entry, a page request is started. Press CH A and CH Y buttons to change the subcode pages:

30. CANCEL: The CANCEL button will exit from any Teletext

on the display. Press CANCEL button again to exit Teletext and return to live TV broadcast.

General Description Installing Batteries in the Remote Control Installing Batteries — - 9 —} \ N\ Open the battery compartment | À cover on the back side. Insert two 1.5V AAA size batteries 30°[30 in correct polarity, Dont mix old or [| used batteries with new ones 2xsize 4 Point the remote towards the remote control AAA LSV| || sensor ofthe TV and us it within 8 meters. 4 Putine used batteries into the recyeling bin Since they can negatvely affect the À environment. / 3 Ciosed the cover. Ne NOTES: + One loading of batteries will last for 1 year under normal use. + If you do not intend to use the remote controller for a long period of time, remove them to avoid damage due to leskage. + Do not use old and new batteries together. + The batteries (battery pack or batteries installed) shall not exposed to excessive heat such as sunshine, fire or the like. External Connecti Antenna connectiol Antenna input impedance of this unit is 75ohm. VHF/UHF 75ohm coaxial cable can be connected to the antenna jack directly, if the antenna cable is 300ohm parallel flat feeder cable, you need to use the 3000hm/75ohm converter to connect the antenna cable to the antenna jack. For details Please refer to the following drawing. Antennas with 300 0 flat twins Leads Antennas with 75 Q Round Leads Use a 75ohm - 300ohm converter —= ref —Gn ob 3000hm coaxial cable 750hm coaxial cable Antenna cable Antenna feeder

External Connecti Connecting VCR These instructions assume that you have already connected your TV to an antenna or a cable TV system. Skip step 1 if you have not yet connected to an antenna or a cable system.

VCR Rear Panel AUDIO OUT | TV Rear Panel RF Cable (Not supplied) 12] YPbPr cable(Not supplied) Audio Cable (Not supplied) Follow the instructions in Viewing a VCR or Camcorder Tape to view your VCR tape. Each VCR has a different back panel configuration When connecting a VCR, match the color of the connection terminal to the cable.

1. Unplug the cable or antenna from the back of the TV.

2. Connect the cable or antenna to the ANT IN terminal on the

3. Connect an RF Cable between the ANT OUT terminal on the

VCR and the ANT IN terminal on the TV.

4. Connect a Component Cable between the COMPONENT

D, Pb, Pr] jacks on the DVD player and YPbPr jack on the TV.

5. Connect Audio Cables between the AUDIO OUT jacks on the

VER and the AUDIO Land AUDIO R jacks on the TV. Note:

1. Whenever you connect an external device to your TV, make

sure that power on the unit is turned off.

2. When connecting an external device, match the color of the

connection terminal to the cable.

External Connection Connecting a Camcorder The rear panel jacks on your TV make it easy to connect a camcorder to your TV. They allow you to view the camcorder tapes without using a VCR Each Camcorder has a different back panel configuration. When connecting a Camcorder or DVD, match the color of the connection terminal to the cable. udio Cable (Not supplied) Video Cable (Not supplied) Camcorder LE) CO Ë Rod Q = — HoM13 OPTIQUE

1. Connect a Video Cable between the AV VIDEO in jacks on the TV and the VIDEO OUT jack

2. Connect Audio Cables between the AUDIO L and AUDIO R jacks on the TV and the AUDIO

OUT jacks on the camcorder.

3. Connect a Video Cable between the AV VIDEO IN jacks on the TV and the VIDEO OUT jack

4. Connect Audio Cables between the component IN AUDIO L and R jacks on the TV and the

AUDIO OUT jack on the DVD Notes:

1. Whenever you connect an external device to your TV, make sure that power on the unit

2. When connecting an external device, match the color of the connection terminal to the

External Connecti Connecting DVD Player/Set-Top Box via HDMI This connection can only be made if there is a HDMI Output connector on the external device. DVD Player! Set-Top Box HDMI Cable (Not supplied) What is HDMI? HDMI, or high-definition multimedia interface, is a next-generation interface that enables the transmission of digital audio and video signals using a single cable without compression. Multimedia interface is a more accurate name for it especially because it allows multiple channels of digital audio (5.1 channels). The difference between HDMI and DVI is that the HDMI device is smaller in size, has the HDCP (High Bandwidth Digital Copy Protection) coding feature installed, and supports multi-channel digital audio. Each DVD player/STB has a different back panel configuration. Connect an HDMI Cable between the HDMI, HDMI2, HDMI3 connector on the TV and the HDMI connector on the DVD player/Set-Top Box. Notes: 1.Whenever you connect an external device to your TV, make sure that power on the unit is turned off. 2.When connecting an external device, match the color of the connection terminal to the cable.

External Connection Connecting Digital Audio System The rear panel jacks on your TV make it easy to connect a Digital Audio System to your TV. Digital Audio System TV Rear Panel (Black) OPTICAL

5.1 CH audio is possible when the TV is connected to an external device supporting 5.1 CH.

Connect an OPTICAL Cable between the OPTICAL jacks on the TV and the Digital Audio Input jacks on the Digital Audio System. When a Digital Audio System is connected to the OPTICAL terminal: Decrease the gain (volume) of the TV, and adjust the volume level with the Digital Audio System's volume control.

External Connectio: PC Cable (Not supplied) Each PC has a different back panel configuration. Connect a PC Audio Cable between PC AUDIO IN jack on the TV and the Audio Out jack of the soundcard on your computer. You should set PC software before you connect a PC to your TV (please refer to "PC Display" settings) Notes:

1. Whenever you connect an external device to your TV, make sure that power on the

2. When connecting an external device, match the color of the connection terminal to

1 Input Setup Press INPUT key on the remote control to enter "INPUT SOURCE" menu. Use 4 key to select a input source and press ENTER key to confirm.

Component HOMI2 HOM3 U Home 2 Channels Selection There are four ways to select channel:

1) Using number keys, and “ENTER” keys on the remote control to select channel directly.

To select channel 90, press ® = ® = - When you use the number buttons, you can directly select channels that were either erased or not memorized.

2) Using CH 47» key on the remote control or on your TV to select channel.

When you press the CH 4 key, the TV changes channels in sequence. You will see all the channels that the TV has memorized. You will not see channels that were either erased or not memorized.

3) Press RECALL key to return to previous channel, press it again to return to current channel.

To quickly switch between two channels that are far apart, tune to one channel, then use the number keys to select the second channel. Then use the RECALL button to quickly altemate between them. RECALL is not activated if no channel has been changed after TV turning on.

4) Select channels from "Channels List" or "Favorite Li

Press “ENTER" key to choose from "Channel List" menu. 3 Volume Adjustment and Mute Setup Volume adjustment Press VOL / - key on the remote control or the TV to display "Volume" menu, adjust the volume of TV between 0 to 100 by using VOL / -key:

( To increase the volume, press VOL + key: ( To decrease the volume, press VOL - key: Mute Press “MUTE” and the sound cuts off. The MUTE icon will appear in the lower-right comer of the screen. To resume sound, press the “MUTE" button again, or simply press the VOL+ key. À current Channel Information Press “INFO” key on the remote control to view current channel information, the indications of channel information are listed in the following table. Thurs 1301 01/162007 oem Press “EXIT” key on the remote control to exit this OSD. 5 £pG Menu Press BACK/GUIDE key to enter "EPG" menu, the first line displays current channel number, channel name, event title and current time. The following line displays all programs which will be displayed in this channel, press A/Y key to select the program you desired, then press “ENTER” key to enter this program to watch. Reminder use “Reminder”(ENTER) button to reserve programs. lf the TV is in DTV mode, it will automatically turn to the reserved program at the scheduled time. Press 4 key and select “Schecule” option to look up the reminder list. Channel List Program List Nine Digtal Program Name | Even à Nine Digtal HD Nine Guide Press EXIT key on the remote control to exit this OSD.

Menu system instruction

1. Press MENU key to display the main menu on the screen.

2. Press A/Y key to select "Picture" option

3. Press à key to enter "Picture" submenu

Picture Contrast Adjusts the lightness and darkness between objects and the background Sms Sharpness Brightness Uint Adjusts the brightness of the picture. Backlight Color Adjusts the colors, making them lighter or darker. Color Temperature 4 Standard Sharpness Aspect Ratio € 169 Adjusts the outline of objects to either sharpen them or make them more dull Noise Reduction < Middle Open HDR « Aub Tint Adjusts the Tint of the picture. Backlight You can Change the brightness of the entire screen according to your preference.

2. Press 4/R key to increace or decreace the backlight value.

‘ Backight: Adjusts the brighiness of the whole screen. Color Temperature You can change the color of the entire screen according to your preference.

1. Press A/Y key to select "Color Temperature" option.

2. Press 4/h key to select one color temp.

1. Press A/Y key to select “Aspect Ratio” option.

2. Press 4/R key to change the size of the picture on the size of the picture on the screen.

Noise Reduction Press A/Y key to select the Noise Reduction mode. You can select the right mode to match the pictures. Open HDR

1. Press A/Y key to select “Open HDR” option.

2. Press 4 key to select “Auto”, ‘Low’, “Middle” or “High”

Menu system instruction

1. Press MENU key to display the main menu on the screen.

2. Press A/Y key to select "Sound" option.

3. Press à key to enter "Sound" submenu.

Sound Sound Mode You can select the type of the special sound effect to be used when watching a given broadcast. CondMode 4 Standard > Your TV has five sound settings (“Standard”, x “Music”, “Movie”, “Sport”, “User”) that are preset à Equalizer at the factory.

1. Press A/Y key to select "Sound Mode" option. Balance

2. Press /k key to select one sound mode.

Auto Volume Limit ‘ Standard: Selects the normal sound mode. ‘ Music: Provides clear and live sound for music. ‘ Movie: Provides live and full sound for movies. ‘e Sports: Emphasizes bass over olher sounds. ‘e User: Selects your custom sound settings Dolby Audio Process Surround Sound 4 Equalizer BE « Set id li di et sound equalizer mode. AD Switch Balance Ifthe volumes of the left speaker and the right speaker are not the same, you can adjust the “Balance” to suit your personal preference.

1. Press A/Y key to select "Balance" option.

2. Press /k key to decrease or increase the value of the item.

Auto Volume Limit Each broadcasting station has its own signal conditions, and it is inconvenient to adjust the volume every time the channel is changed. “AVL” automatically adjusts the volume of the desired channel by lowering the sound output when the modulation signal is high or by raising the sound output when the modulation signal is low.

1. Press A/Y key to select "AVL” option.

2. Press /b key to select “On” or “Off.

Surround sound This is used to turn on surround sound to gain better sound effect.

1. Press A/Y key to select "Surround sound” option.

2. Press /b key to select “On” or “Off.

Dolby Audio Process This is used to set DAP.

1. Press A/Y key to select "Dolby Audio Process” option.

2. Press /b key to select “On” or “Off.

Menu system instruction DBX This is used to set DBX.

1. Press A/Y key to select “DBX" option.

2. Press 4} key to select “On' or “Of”. J Sound

Menu system instruction

1. Press A/Y key to select “OSD Language"

2. Press ENTER or & key to select a proper

language for OSD. OSD Time OSD Time CEE Set the preferred amount of time for the OSD to be displayed on the screen. ; Link Setup HBBTV rs Im This is used to set HBBTV Turn on or turn off the HBBTV function Reset Link Setup " PC Adjust

1. Press A/Y key to select “Link Setup” option.

2. Press A/V key to select "Time" option.

3. Press b key to enter "Time" submenu.

Auto Sync You can modify the time of your TV set in Manual mode. In Auto mode, the “clock” is decided by the DTV signal. few minutes and don't tu off the power, it will turn off automaticly when updating finish. Clock --:-- When Auto Sync is on, the clock is got from DTV streams; Set the clock when Auto Sync is off.

Menu system instruction Off Time In "Off Time” item, press button or ENTER button to enter the submenu, set the day & time il to turn off the TV set. £ J Setting Time ous Auto Sync In "On Time” item, press button or ENTER button to enter the submenu, set the time to turn Clock 13:01 on the TV set, when the TV set is in the standby mode. You can also choose which day to control Off Time you TV set in a week. On Time Sleep Timer

1. Press A/Y key to select "Sleep Timer” option. Sleep Timer « of

2. Press 4 key repeatedly until the desired

time appears (Off, 10mins, 20mins, 30mins, © Auto Sleep « of 60mins, 90mins, 120mins, 180mins, 240mins). Notes: The sleep timer you have set will be * Time Zone € Westem > cancelled when the TV turns off or if a power failure occurs. Notes: When the time is less than 60 seconds, remind information will be displayed on the screen. Press any key button to cancel timer function. Auto Sleep Press A/Y key to select whether to open the No signal Power off features. If this function is opened, the TV will power off when there is no signal. Time Zone You can choose it to modify your time zone in the TV set.

1. Press A/Y key to select "Time Zone" option.

2. Press 4 key to select time zone.

Reset 1.Press “A/W" key to select "Reset" option. 2.Press “b" or “ENTER" key to confirm. 3.Press "Yes" to confirm again, TV will turn off automaticlly and change all setting to factory setting. PC Adjust This option is only used in VGA.

1. Press A/Y key to select “PC Adjust” option.

Menu system instruction The "Lock" feature automatically locks out programming that is deemed inappropriate for children. The user must first enter a Password before any of the lock restrictions can be set up or changed.

3. Press > key to enter "Lock" submenu, "Enter Password” menu will appear, enter your 4-digit

password to enter "Lock” submenu (the default and universal password is 1980). Lock System Set the Lock function on or off.

1. Press A/Y key to select "Lock System" option.

2. Press 4 key to select "On" or "Off.

Choose any 4-digits for your new password and enter them. As soon as the 4 digits are entered, the cursor skipped to “Confirm Password” item, re-enter the same 4 digits, and your new password has been memorized. When the programs is locked, you can also press the menu key, Info key and so on. Then you can press 47 key to call back the input-password window. Parental Guidance This option only used in DTV mode.

1. Press A/Y key to select ‘Parental Guidance" option

2.Prsee 4h key to select the lock level of the Parental Rate. CI CAM PIN Code Set CI CAM Pin Code Function. Lock Lock System Set Password SCA PnEe [

Menu system instruction

Connect the USB disk to the standard USB port before use PVR. Select Disk: Press “ENTER" button to enter submenu and press “4” Lo choose the disk for PVR. Tine Shift Size: Display the buffer used for PVR. Format Start: Press ENTER" button to enter format submenu. Speed: Display the disk writing/reading speed.

1. The disk must be formatted when first used for PVR, so backup the original data in the disk.

Is suggested use a special disk for PVR. Don't modify the PVR file in PC.

2. All the time is not precise, just for reference.

Ate you sure want lo stop PVR? Start Record Press A/Vkey to select “Start Record”. If the storage device is ready, press “ENTER” key to start record The recording menus will disappear in 5 seconds, press “ENTER or A/V/4/»" key to recall them out. When recording, press “Im” key again, then you can choose to stop recording or continue:

Menu system instruction Start Timeshift In DTV channel, press “ »/I1 ” key to pause, press it again to resume playback. This is the “Time Shift”. During the suspension the image are temporarily stored in the disk, so programs will not miss the suspension period, the length of time may be suspended by the size of the disk buffer space constraints. CH 9 Nine Digital 00:00:12 RS CH 9 Nine Digital Record Files Press A/Vkey to select "Recorded List”. If the storage device is ready, press “ENTER” key to check the record list.

1) Press A/Y key to select record file

1) Press and “ENTER" key to delete the selected file.

Record Files LON |Chennel | Program 9 NreDigial MALCOLMINTHEM MINTHE MIDDLE

2. Press A/ key to select "Program" option.

3. Press b key to enter "Program submenu. D Program

Auto Tuning Press A/Y key to select "Auto Tuning" option. The number of searched channels will be shown on the screen. 2 DTVManual Tuning Note: If you want to exit the whole searching, ATV Manual Tuning you can press EXIT button. LNB Setting DTV Manual Tuning You can use 4/ button or input number to Signal Information choose the channel. Then press ENTER button to search, the TV will store the DTV channel if there CI Information is a DTV signal present. ATV Manual Tuning In the ATV/DTV source, you can choose "ATV Manual Tuning" to enter "ATV Manual Tuning" menu. Current CH You can see the current channel number and you can press 4/»button to choose the channel you want to modify. It will be searched and saved automatically. Color System Select the "Color System" option, press 4/»- on the remote control to change. The color system will be changed repeatediy in the order: PAL-N, PAL-M, NTSC or AUTO. Fine Tune In case of unfavorable image or sound of TV program, you can use "Fine Tune”. Frequency You can see the frequency of the searched channels. Save You can see the channel you choosed DTV Manual Tuning ATV Manual Tuning

Menu system instructio: LNB Setting This is used to set up DVBS parameter. Signal Information (Used only in DTV)

1. Press A/Y key to select “Signal Information" option.

2. Press “ENTER'or k key, you can see the information of the DTV channel.

NOTE: Signal Quality/Signal Strength (DTV Only): Unlike analogue channels, which can vary in reception quality, digital channels must have perfect reception quality or you will not receive them at all. So, unlike analogue channels, you are not able fine tune à digital channel. If the signal strength indicates that the signal is weak, a possible solution is to adjust your antenna to increase the signal strength. Continue to adjust the antenna until you find the best position with the strongest signal. Cl Information Cl information function. Program Signal Info Channel 9 Name: Nine Digital Mondulation: 64QAM Quality 100 Strength: 0

2. Press A/Y key to select "Network" option.

3. Press b key to enter "Network" submenu. Network

Wi-Fi When the Wi-Fi wireless network is going to be used, if select auto scan,select "Auto Scan” option and press Y key to select your Wi-Fi network, then enter password to connect your Wi-Fi network Weke OnLAN 4 On + If select manual input, select "Manual Input" option, then setting up the IP, Netmask, Gateway and DNS in 1 WakeOnWLAN 4 On sequence. When the setting complete, press the "Connect" option. Ethernet Not Connected > Ethernet Network When the wired network is used, if select dynamic IP Network / Wi-Fi address setting, pitch on the "DHCP" in the "Configuration", and press the "Connect" button to enter. If select static IP address setting, pitch on the "Static" in the "Configuration", then setting up the IP, Netmask, Gateway and DNS in sequence. When the setting complete, press the"Connect". Manual Input Network Wake On LAN/Wake On WLAN NenokIMr Set the mobile phone to enter the same network ing, Pl segment as the TV. When the mobile phone enters Youtube, you will find a push icon in the upper right corner. After clicking, you can search for the TV, and then push to wake up the TV. 1724667130 > Netmask 2552552540 > Gateway 172.16.66.254 DNS 172.16.64.81 Connect

2. Press A/Y key to select "About" option.

3. Press b key to enter "About" submenu

Netflix Netflix Deactive 1.Press A/Y key to select “Netflix Deactive 2.Press or ENTER key to confirm. 3.Press “YES” to confirm again, the Netflix will be activated. option. Terminate Netflix 1.Press A/Y key to select “Terminate Netix" option. 2.Press à or ENTER key to confirm. 3.Press “YES” to confirm again, the Netfix will be terminated. Netflix ESN Display the Netfix Esn information. Netflix Version Display the Netfix version. View End-User License Agreement 1.Press A/Y key to select "View End-User License Agreement" option 2.Press & or "ENTER" key to display View End-User License Agreement.

Menu system instructio: about System information 1.Press A/Y key to select "System information" option. 2.Press b or "ENTER" key to display system information. Net Ready Information 1.Press A/Y key to select "Net Ready Information" option. 2.Press b or "ENTER" key to display net ready information. Software Update(USB) When the TV need to be updated, please copy the new software to a USB storage to TV, then operating by following steps. 1.Press A/Y key to select “Software Update” option. 2.Press or ENTER key to confirm. 3.Press “YES” to confirm again, the TV will update by USB. Please wait a few minutes and don't turn off the power, it will turn off automatically when updating is finish. Internet Update Check This can update TV through internet.

Home Operati Setup wizard Press “HOME” key to enter home interface. Press arrow key to select a input source and press ENTER key to confirm CCS « E:- 1)NETFLIX © Use arrow key to select | NETELIX | icon, then press “ENTER” key to enter NETFLIX. © Use arrow button to select one video and press “ENTER” key to play. Press “MENU” key to exit playing. © Use arrow key to browse the pages. press “MENU” key to return to main menu and press “EXIT” key to exit. Sgnin Got ready to watch thousands of TV shows and movies. Email address

© Use arrow key to select | emma |icon, then press “ENTER key to enter Youtube. @ Use arrow button to select one video and press “ENTER” key to play Press "BACK” key to exit playing © Press key to open or close control menu when playing 3)Facebook

© Use arrow key to select DSEX icon, then press “ENTER” key to enter Facebook. © Visit https:/www.facebook.com/device on your smartphone or computer to get code and enter the code. € Press arrow key to browse the pages and press “ENTER” key to view Press *BACK” key to return to main menu and press “EXIT” key to exit Facebook. Red key: log in or log out Facebook. Green key: refresh current page. Log CE om RUE

Home Operati APP setup A)Twitter © Use arrow key to select |... licon, then press “ENTER” key to enter Twitter. Authorize TVMessage to use your account? Ces © Input the right Email and password, then select “Authorize app” button and press “ENTER” key to log in. © Use arrow key to browse the pages. press “BACK key to return to main menu and press “EXIT” key to exit twitter. Red key: log in or log out twitter. Green key: refresh current page. Yellow key: write new twitter. Blue key: Search twitter.

5)YAHOO Weather © Use arrow key to select | icon, then press “ENTER” key to enter YAHOOweather. © Input a city to get the weather information: Press arrow key to adjust Picture, Sound, Setting, Lock, PVR Option, Program, Network or About.

Digital Media Playe Introduction This TV is embedded with one USB port digital media player. It can find the devices support USB1.1/2.0 including flash disk, USB hard disk and digital camera. It supports functions as: Display pictures. Play music files, Play video files. Notice:

1. In order to avoid affecting the user's viewing experience, please use the better quality and

2. Play, preview some of the non-standard files may appear abnormal, please understand.

1. Under the USB channel, you can use only the remote control.

2. Play Control menu to enter the playing surface to press the menu button pop-up menu

Troubleshooting If you have any problem, check the couter measures for each symptom listed below. The following symptoms may have been. caused by inappropriate adjustment rather than actual malfunction of the unit. If the trouble persists, contact the Customer Care Centre, see back page for contact details. Symptoms Possible solutions Please check the power cord plugged in and that the power outlet works. Unplug the power cord and plug it in after 60 seconds and restart the TV. No power Please check antenna connection. Station may be experiencing problems, please tune to another station. Please adjust the settings of contrast and brightness. No picture Please increase the volume. Please check TV is under mute mode, press MUTE button on the remote control. Please check sound settings Good picture but no If external devices are being used, check their volumes are sound not set too low or turned off. If using AVI or Component inputs, please make sure cables are connected properly and not loose. If using DVI to HDMI cable, a separate audio cable is required. Make sure a headphone jack is not connected. Please check antenna connection and antenna condition. Good sound but abnormal lfusing Component input, please check Component color or no picture connections, incorrect or loose connections may cause colour problems or cause the screen to be blank. Batteries of remote control may have exhausted, if necessary, please change the batteries. Clean the remote control lens. The distance between LED TV and remote control should be within 8m, within recommended operating angle and path is free of obstructions. No response to remote control V-HEIGHT value may be set too big, restart computer and Full screen flickering enter safe mode, then set monitor parameters to correct under VGA value according to adjustment description. Horizontal stripes Sample phase may be deflected, adjust phase according to under VGA picture position. Although the LED screen is made With high-precision technology and 99.99% or more of the pixels are Colored dots may be effective, black dots may appear or bright points of light present on the screen (red, blue, or green) may appear constantiy on the LED screen. This is a structural property of the LED screen and not a malfunction. Keep the TV away from noisy electrical sources such as cars, hair dryers, welders, and all optional equipment. Electrical atmospheric interference such as local or distant lightning storms may cause picture to break up. When installing optional equipment, leave some space between the optional equipment and the TV. Check the antenna and connection. Keep the antenna away from any power or input/output cables. Lil Picture is breaking up

Troubleshootin After Auto Tuning only Check your area is covered by Digital Video Broadcasts. some channels are Try re-tuning or manually tuning missing channels. available Check that you are using the correct antenna type. Channel cannot be Check if the channel has been blocked in the main menu selected settings. Please check connecting USB cable and power supply is connected. USB not playing Hard drive has not been formatted. Please make sure USB disk is compatible and the multimedia data formats are supported. Picture is distorted, macroblock, small block, dots, pixelization, etc Compression of video contents may cause distortion especially on fast moving pictures such as sports and action movies. Check cable connections, make sure a video cable is not connected Noise from speaker to an audio input. Low signal level may cause sound distortion. Check if the Off Timer is set to On in the Setup menu. Sleep Timer may have been enabled Ifthere is no signal for about 10 minutes ( 2 minutes in VGA) from TV turns off automatically an input, the TV will turn off. If connected to your PC, check your PC power settings. Make sure the AC power cord is plugged in securely to the wall outlet and the TV. TV turns on automatically Check if the On Timer is set to On in the Setup menu. Black bars on each side will be shown on HD channels when displaying SD (4:3) contents. Picture is not shown in Black bars on Top & Bottom will be shown on movies that have full screen aspect ratios different from your TV. Adjust picture size option on your external device or TV to full screen. WARNING Never place a television set in an unstable location. A television set may fall, causing serious personal injury or death. Many injuries, particularly to children, can be avoided by taking simple precautions such as: - Using cabinets or stands recommended by the manufacturer of the television set. - Only using furniture that can safety support the television set. - Ensuring the television set is not overhanging the edge of the supporting furniture. - Not placing the television set on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and the television set to a suitable support. - Not placing the television set on cloth or other materials that may be located between the television set and supporting furniture. - Educating children about the dangers of climbing on furniture to reach the television set or its controls If your existing television set is being retained and relocated, the same considerations as above should be applied. The plug or appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.

WARRANTY CONDITIONS OPERATING MANAGEMENT: Your product is guaranteed 2 years. To request support, contact the customer service at 0811 482 202. You will then be asked the defective part and the original invoice stating the product regulation, We may ask you for photos of your appliance. FAILURE TO PACKING: Kit appeared, after unpacking the product or device, a vice preventing the use ofthe product in its expected configuration, contact the customer service within 72 hours worked.

DISCLAIMER OF WARRANTY

DISCLAIMER OF WARRANTY RELATED TO THE ORIGIN OF DAMAGES The guarantee does not apply in case of accidental physical damage, it does not cover such damage and faiures that resulted: + improper installation (of a bad installation) or a misuse or poor maintenance of the product. + improper use of the material or not complying with the instructions in the user manual. __ lightning, flood, fire, power surge, shock, poor ventilation, a fall, discoloration due to the action of light, burning, humidity, excessive heating without humidifier, or irregular ground or insects. + repairs made and/or working on the hardware and/or opening of it by an unauthorized person by the manufacturer. + maintenance, repair or replacement of parts due to normal usury or failure to maintain + modification of the construction and original features of the guaranteed product corrosion, oxidation, a bad connection nor an external power supply problem EXCLUSION OF WARRANTIES RELATING TO THE NATURE OF DAMAGES (INDIRECTS DAMAGES) The guarantee covers only the right to repair or replace the guaranteed product. Consequently, the indirect damage resulting from the failure or damage not covered by warranty, including: e Commissioning costs, adjusting, cleaning: e Damage of any kind resulting from the unavailability of the product guaranteed during the period between deterioration and failure and repair or the replacement of the product guaranteed. OTHER EXCLUSIONS Damage and faults under specific exclusions in the warranty manufacture guaranteed product, as mentioned in the product instructions for use; e The aesthetic damage: æ The products guarantee that the customer is not able to return or those who returned without their accessories. PIXEL POLICY ® In accordance with the ISO 13406-2 norm, a product is considered defective when the number of dead or lit pixels is over 3.

WARRANTY CONDITIO SUPPORT Please refer you to the board below to find easily your alter sales number:

COUNTRY PHONE NUMBER EMAIL WEB

FR www.mms-support.net (+33) 0811 482202 | sav@polaroïd-France.com . pport: (only for metropolitan ww.polaroid.tech France) = WI +352.26.11.00.90 | support BE@market-maker.fr NN = upport_BE@) DE _— +49359127224626 | Service@letmerepair.com IT E E 199 309 314 helpdesk@stitaly.it ES ÆE + 3495217904 79 | support_ES@market-maker.fr PT [a] (#34) 952 179 557 info@letmerepair.pt cH 0900 77 88 99 info@dstv.ch Declaration of conformity EU: Market Maker Brand Licensing, hereby declares that this equipment, conforms to the essential requirements and other relevant provisions of Directive 2014/53/UE. The declaration of Conformity can be viewed al the following address: httpz/Awww.mms-supportnetOTA/ECD_MMBL_TV.SHD32PROO1.pdf CEX PLR IP Holdings, LLC, il licensees and affliates, fully support all electronic waste initiatives. As responsible stewards of the environment, and to avoid violating established laws, you should property dispose of this product in compliance with all applicable regulations, directives or other governances in the area where you reside. Please check with local authorities or the retailer where you purchased this product to determine a location where you can appropriately dispose of the product. THE DISPOSAL OF ELECTRICAL AND ELECTRONIC EQUIPMENT WASTE PRODUCTS ON THE PART OF

FINAL USERS IN THE EUROPEAN UNION

This symbol on the product or on the container indicates that this product cannot be eliminated with the general waste. The user is responsible for eliminating this kind of waste by throwing them away at a ‘recycling point" specifically for electrical and electronic waste. Selective collection and electrical equipment recycling contribute to preserve natural resources and warrant waste recycling to protect environment and health. In order to receive further information about electrical and electronic waste collecting and recycling, contact your Local Council, the service of household waste or the establishment where the product was acquired.

&Polaroid Polaroid, Polaroid & Pixel, Polaroid Classic Border Logo and Instantiy recognizable. Instantiy Polaroïd Color Spectrum are trademarks of PLR IP Holdings, reassuring. The Polaroïd Classic LLC, used under license. PLR IP Holdings, LLC does not nn Méufaciur this product or provide any Manufacturers he best qualis o our rend and Warranty or support that contributes to our rich heritage of www.polaroïd.tech Suslhy and Innovation. Market Maker Brand Licensing - 79/81 Ancienne Route © 2019. AII Rights Reserved Nationale 7-69570 Dardilly, France Ê TS Questions? M you st have quest Need some help? call our ho Inc: This manual wi help you en) 0811 482 202