ELLE2720 - Kitchen hood FALMEC - Free user manual and instructions

Product type	Extractor or recirculation cooker hood
Number of speeds	4 speeds (1 to 4, speed 4 timed)
Control	Touch electronic + radio control 433.92 MHz
Lighting	LED with adjustable intensity and color temperature (2700 K to 5600 K)
Timer	Programmable automatic shut-off after 15 minutes
Anti-grease metal filters	Dishwasher-safe or hand-washable (every month or after 30 hours of use)
Charcoal/zeolite filter (recirculation version)	Regeneration every 18 months (200°C, 1h), replacement after 3 years
External material	Brushed stainless steel and glass
Minimum distance above a gas hob	65 cm (may be reduced according to instructions)
Maximum negative pressure when operating simultaneously with other appliances	4 Pa (according to German deviation)
Power supply	See rating plate inside the hood
Safety	Automatic disconnection in case of failure; outdoor use prohibited
Maintenance	External cleaning every 15 days with a soft cloth and mild detergent; do not use abrasive products
Repairability	Interventions reserved for an approved Service Centre; use original spare parts

Frequently Asked Questions - ELLE2720 FALMEC

What is the minimum distance between the hood and a gas hob?

The minimum distance is 65 cm. However, it may be reduced to the height indicated in the installation instructions if the EN60335-2-31 standard allows it. Always follow the instructions of your hob if they specify a greater distance.

Can I install the hood outdoors?

No, the hood is designed for indoor use only. Do not install it outdoors or expose it to rain, wind, or other weather elements.

How to clean the anti-grease metal filters?

The metal filters should be washed at least once a month or after 30 hours of use. You can soak them in boiling water with dish soap, or put them in the dishwasher at a low temperature (55°C max). Rinse thoroughly and dry before reinstalling.

What to do if the remote control stops working?

First check that the hood is powered on. If the radio control is inactive, you can reset the code: simultaneously press the LIGHT and TIMER buttons on the hood until all LEDs flash, then follow the pairing procedure. If the problem persists, contact an approved Service Centre.

How to adjust the intensity of the LED lighting?

To adjust the intensity, long-press the LIGHT button (♂) on the control panel or on the remote control. The color temperature can also be changed by long-pressing the ON/OFF button to switch from 2700 K to 5600 K.

What is the timer for and how to activate it?

The timer allows automatic motor shut-off after 15 minutes. Activate it by pressing the TIMER button (♀); a red LED flashes. To deactivate, press TIMER again or the ON/OFF button.

Can I use the hood without the metal filters?

No, it is essential to always use the anti-grease metal filters. Without them, grease and dirt would deposit inside the hood, compromising its operation and increasing the risk of fire.

How to install the hood in recirculation (filtering) mode?

For recirculation use, make sure the activated charcoal (or zeolite) filters are installed. Remove the non-return flap on the motor's air outlet connection. The purified air will then be recirculated into the room.

What to do in case of LED lighting failure?

The LED lighting is designed for a long lifespan. In case of failure, do not attempt to replace it yourself: contact the retailer or an approved Service Centre for repair.

How to dispose of the hood at the end of its life?

The hood is an Electrical and Electronic Equipment Waste (WEEE). Do not throw it with household waste. Take it to a designated collection point or contact your retailer for take-back. Comply with local legislation.

USER MANUAL ELLE2720 FALMEC

INSTRUCTIONS BOOKLET

INSTRUCTIONS BOOKLET

INSTRUCTIONS BOOKLET EN

Installation operations are to be carried out by skilled and qualified installers in accordance with the instructions in this booklet and in compliance with the regulations in force. DO NOT use the hood if the power supply cable or other components are damaged: disconnect the hood from the electrical power supply and contact the Dealer or an authorized Servicing Dealer for repairs.

Do not modify the electrical, mechanical, or functional structure of the equipment.

Do not personally try to carry out repairs or replacements. Interventions carried out by incompetent and unauthorized persons can cause serious damage to the unit or physical and personal harm, not covered by the Manufacturer's warranty.

WARNING FOR THE INSTALLER

TECHNICAL SAFETY

Before installing the hood, check the integrity and function of each part. Should anomalies be noted, do not proceed with installation and contact the Dealer.

Do NOT install the hood if an aesthetic (or cosmetic) defect has been detected. Put it back into its original package and contact the dealer.

No claim can be made for aesthetic (or cosmetic) defects once it has been installed.

During installation, always use personal protective equipment (e.g., safety shoes) and adopt prudent and proper conduct.

The installation kit (screws and plugs) supplied with the hood is only to be used on masonry walls: in case of installation on walls of a different material, assess other installation options keeping in mind the type of wall surface and the weight of the hood (indicated on page 2).

Keep in mind that installations with different types of fastening systems from those supplied, or which are not compliant, can cause electrical and mechanical seal danger.

Do not install the hood outdoors and do not expose it to atmospheric elements (rain, wind, etc.).

ELECTRICAL SAFETY

The electrical system to which the hood is to be connected must be in accordance with local standards and supplied with an earthed connection in compliance with safety regulations in the country of use. It must also comply with European standards regarding radio antistatic properties.

Before installing the hood, check that the electrical mains power supply corresponds with what is reported on the identification plate located inside the hood.

The socket used to connect the installed equipment to the electrical power supply must be within reach; otherwise, install a mains switch to disconnect the hood when required.

Any changes to the electrical system must be carried out by a qualified electrician.

The maximum length of the flue fastening screws (supplied by the manufacturer) must be 13 mm. Use of non-compliant screws with these instructions can lead to danger of an electrical nature.

Do not try to solve the problem yourself in the event of equipment malfunction, but contact the Dealer or an authorized Servicing Department for repairs.

When installing the hood, disconnect the equipment by removing the plug or switching off the main switch.

FUMES DISCHARGE SAFETY

! Do not connect the equipment to discharge pipes of fumes produced from combustion (for example boilers, fireplaces, etc.).

Before installing the hood, ensure that all standards in force regarding discharge of air out of the room have been complied with.

Deviation for Australia and New Zealand: Range hoods and other cooking fume extractors may adversely affect the safe operation of appliances burning gas or other fuels (including those in other rooms) due to back flow of combustion gases. These gases can potentially result in carbon monoxide poisoning. After installation of a range hood or other cooking fume extractor, the operation of flued gas appliances should be tested by a competent person to ensure that back flow of combustion gases does not occur. (AS/NZS 60335.2.31:2013/A4:2020).

USER WARNINGS

These warnings have been drawn up for your personal safety and those of others. You are therefore kindly asked to read the booklet carefully in its entirety before using or cleaning the equipment.

The Manufacturer declines all responsibility for any damage caused directly, or indirectly, to persons, things and pets as a consequence of failing to comply with the safety warnings indicated in this booklet.

It is imperative that this instruction booklet is kept together with the equipment for any future consultation.

If the equipment is sold or transferred to another person, make sure that the booklet is also supplied so that the new user can be made aware of the hood's operation and relative warnings.

After the stainless steel hood has been installed, it will need to be cleaned to remove any residues remaining from the protection adhesive as well as any grease and oil stains which, if not removed, can cause irreversible damage to the hood surface. To properly clean the unit, the manufacturer recommends using the supplied moist wipes, which are also available sold separately.

Insist on original spare parts.

INTENDED USE

The equipment is solely intended to be used to extract fumes generated from cooking food in non-professional domestic kitchens: any other use is improper. Improper use can cause damage to persons, things, pets and exempts the Manufacturer from any liability.

The equipment can be used by children over the age of 8 and by persons with reduced physical, sensory and mental abilities, or with no experience or knowledge, as long as they do so under supervision or after having received relative instructions regarding safe use of the equipment and understanding of the dangers connected to it.

Children are not to play with the equipment. Cleaning and maintenance by the user must not be carried out by children without supervision.

USE AND CLEANING WARNINGS

Before cleaning or carrying out maintenance operations, disconnect the equipment by removing the plug or switching off the main switch.

Do not use the hood with wet hands or bare feet. Always check that all electrical parts (lights, extractor fan) are off when the equipment is not being used. The maximum overall weight of any objects placed or hung (if applicable) on the hood must not exceed 1.5 kg.

Always supervise the cooking process during the use of deep-fryers: Overheated oil can catch fire.

Do not leave open, unattended flames under the hood.

Do not prepare food over an open flame under the hood.

Never use the hood without the metal anti-grease filters: in this case, grease and dirt will deposit in the equipment and compromise its operation.

Accessible parts of the hood can be hot when used at the same time as the cooking appliances.

Do not carry out any cleaning operations when parts of the hood are still hot.

There can be a risk of fire if cleaning is not carried out according to the instructions and products indicated in this booklet.

Disconnect the main switch when the equipment is not used for long periods of time.

If other appliances that use gas or other fuels are being used at the same time (boiler, stove, fireplaces, etc.), make sure the room where the fumes are discharged is well-ventilated, in compliance with the local regulations.

INSTALLATION

Only intended for qualified personnel.

Before installing the hood, carefully read the chapter 'SAFETY INSTRUCTIONS AND WARNINGS'.

TECHNICAL FEATURES

The technical specifications are exhibited on the labels located inside the hood.

POSITIONING

The minimum distance between the highest part of the cooking equipment and the lowest part of the hood is indicated in the installation instructions.

Generally, when the hood is placed over gas cookers, the distance must be at least 65 cm (25.6"). However, according to standard EN60335-2-31, the minimum distance between the cooker and lower part of the hood can be reduced to the quota reported in the installation instructions.

Should the instructions for the gas cooker specify a greater distance, this must be taken into consideration.

Do not install the hood outdoors and do not expose it to outdoor environment (rain, wind, etc.).

ELECTRICAL CONNECTION

(only intended for qualified personnel)

Disconnect the equipment from electrical mains power supply before carrying out any operations on the hood.

Ensure that the wires inside the hood are not disconnected or cut: in the event of damage, contact your nearest Servicing Department. Refer to qualified personnel for electrical connections.

Connection must be carried out in compliance with the provisions of law in force.

Before connecting the hood to the electrical mains power supply, check that:

• voltage supply corresponds with what is reported on the data plate located inside the hood;
• the electrical system is compliant and can withstand the load (see the technical specifications located inside the hood);
• the power supply plug and cable do not come into contact with temperatures exceeding 70°C ;
• the power supply system is effectively and properly connected to earth in compliance with regulations in force;
• the socket used to connect the hood is within reach.

In case of:

• devices fitted with cables without a plug: the type of plug to use is a "standardised" one. The wires must be connected as follows: yellow-green for earthing, blue for neutral and brown for the phase. The plug must be connected to an adequate safety socket.
• fixed equipment not provided with a power supply cable and plug, or any other device that ensures disconnection from the electrical mains, with an opening gap of the contacts that enables total disconnection in overvoltage category III conditions.

Said disconnection devices must be provided in the mains power supply in compliance with installation regulations.

The yellow/green earth cable must not be cut off by the switch.

The Manufacturer declines all responsibility for failure to comply with the safety regulations.

FUMES DISCHARGE

EXTERNAL EXHAUST HOOD (SUCTION)

In this version the fumes and vapours are discharged outside through the exhaust pipe.

To this end, the hood outlet fitting must be connected via a pipe, to an external output.

The outlet pipe must have:

• a diameter not less than that of the hood fitting.
• a slight slope downwards (drop) in the horizontal sections to prevent condensation from flowing back into the motor. the minimum required number of bends.
• the minimum required length to avoid vibrations and reduce the suction performance of the hood.

You are required to insulate the pipes if it passes through cold environments. In the presence of motors with 800m³/h or higher, a check valve is present to prevent external air flowing back.

Deviation for Germany:

when the kitchen hood is used at the same time as appliances that are powered by energy other than electricity, the negative pressure in the room must not exceed 4 Pa (4 x 10-5 bar).

HOOD WITH INTERNAL RECIRCULATION (FILTERING)

In this model, the air passes through the charcoal filters to be purified and recycled in the environment.

Ensure that the active carbon filters are assembled into the hood; if not, install them as indicated in the assembly instructions.

In this version, the check valve must not be assembled: remove it if it is on the air outlet fitting of the motor.

ASSEMBLY INSTRUCTIONS

only intended for qualified personnel

The hood can be installed in various configurations. The generic assembly steps apply to all installations; for each case, follow the specific steps provided for the required installation.

OPERATION

WHEN TO TURN ON THE HOOD?

Switch on the hood at least one minute before starting to cook to direct fumes and vapours towards the suction surface.

After cooking, leave the hood operating until complete extraction of all vapours and odours. By means of the Timer function, it is possible to set auto switch-off function which will allow the hood to turn off automatically after 15 minutes of operation.

WHICH SPEED IS TO BE SELECTED?

1st speed: maintains the circulation of clean air with low electricity consumption. 2nd speed: normal conditions of use. 3rd speed: presence of strong odours and vapours. 4th speed: rapid disposal of odours and vapours.

WHEN SHOULD THE FILTERS BE WASHED OR REPLACED?

The metal filters must be cleaned every 30 hours of operation.

For further details see the "MAINTENANCE" chap.

ELECTRONIC PUSHBUTTON PANEL

Motor ON/OFF Motor OFF Long impulse: change light tone from 2700K to 5600K
+	Increase speed from 1 to 4 Speed 4 is only active for a few minutes, then speed 3 activates.	The speeds are indicated by the LEDs on the keys: + + - Speed 1 + + - Speed 2 + + - Speed 3 + + - Speed 4 ("+" LED flashing)
-	Reduce speed from 4 to 1
Light on/off Short impulse: turn light on and off Long impulse: adjust intensity
TIMER (red LED flashing) Auto switch-off after 15 min. The function deactivates (red LED off) if: - The TIMER key (●) is pressed again. - The ON/OFF key (●) is pressed.

If the pushbutton panel is completely inactive, before contacting the Technical assistance service, disconnect power temporarily to the appliance (about 5 seconds), possibly by acting on the main

switch, to restore normal operation.

If this measure has no effect, contact the Technical assistance service.

USING THE RADIO CONTROL

(OPTIONAL)

WARNING:

Place the hood away from sources of electromagnetic waves (e.g. microwave ovens), which could interfere with the radio control and with the hood electronics.

The maximum operating distance is 5 metres, that may vary according to the presence of electromagnetic interferences.

Radio control operated at 433.92MHz.

The radio control consists of two parts: - the receiver built into the hood; - the transmitter shown here in the figure.

DESCRIPTION OF TRANSMITTING COMMANDS
	UP Motor switch-on and speed increase from 1 to 4. Speed 4 is only active for a few minutes.
	DOWN Speed decrease and motor switch-off.
	Light on/off Short impulse: turn light on and off Long impulse: adjust intensity
	TIMER ON: The motor automatically switches off after 15 min. The function is automatically disabled if the motor is switched off (key)
	Command transmission active

ACTIVATION PROCEDURE

Before using the radio control, follow the procedure below on the hood pushbutton panel:

• Press LIGHT (↑) and TIMER (↑) simultaneously until all LEDs start flashing.
• Release the two keys and press LIGHT (↑) again until all LEDs are lit up.
• Release LIGHT: now the receiver is active.

This procedure is also used to deactivate the receiver.

RADIO CONTROL CODE CHANGE

With only one radio control, go directly to point 2.

With several radio controls in the same room, a new code can be created by following the procedure below.

Disconnect the power to the hood before starting the procedure.

1) - CREATE A NEW CODE

The procedure is to be carried out on the radio control.

• Press LIGHT (※) and TIMER (®) simultaneously until the display starts flashing.
• Press DOWN on the radio control: saving is confirmed by three brief flashes of the display. The new code cancels and replaces the previous default code.

Reconnect the hood to the electrical power supply, making sure that the lights and motor are off.

2) - ASSOCIATING THE RADIO CONTROL WITH THE HOOD USING THE ELECTRONIC PUSHBUTTON PANEL

Press TIMER on the hood pushbutton panel for 2 seconds: the red LED lights up.

Press any key on the radio control within 10 seconds.

RESTORING DEFAULT CODE

The procedure is to be carried out if the hood is disposed of, sold or transferred.

Disconnect the power to the hood before starting the procedure.

• Press UP and DOWN simultaneously on the radio control for more than 5 seconds: reset is confirmed by three brief flashes of the display.
• Reconnect the hood to the electrical power supply.
• Proceed with associating the hood and the radio control, as described in point 2.

MAINTENANCE

Before cleaning or carrying out maintenance operations, disconnect the equipment by removing the plug or switching off the main switch.

Do not use detergents containing abrasive, acidic or corrosive substances or abrasive cloths.

Regular maintenance guarantees proper operation and performance over time. Special attention is to be paid to the metal anti-grease filters: frequent cleaning of the filters and their supports ensures that no flammable grease is accumulated.

CLEANING OF EXTERNAL SURFACES

You are advised to clean the external surfaces of the hood at least once every 15 days to prevent oily substances and grease from sticking to them. To clean the brushed stainless steel hood, the Manufacturer recommends using "Magic Steel" wipes.

Alternatively and for all the other types of surfaces, it can be cleaned using a damp cloth, slightly moistened with mild, liquid detergent or with any detergent supplied with the appliance.

Complete cleaning by rinsing well and drying with soft cloths.

Do not use too much moisture or water around the push button control panel and lighting devices in order to prevent humidity from reaching electronic parts.

The glass panels can only be cleaned with specific, non-corrosive or non-abrasive detergents using a soft cloth.

The Manufacturer declines all responsibility for failure to comply with these instructions.

CLEANING OF INTERNAL SURFACES

Do not clean electrical parts, or parts related to the motor inside the hood, with liquids or solvents.

For the internal metal parts, see the previous paragraph.

METAL ANTI-GREASE FILTERS

It is advised to frequently wash the metal filters (at least once a month) leaving them to soak in boiling water and cleaning solution for 1 hour, taking care not to bend them.

Do not use corrosive, acid or alkaline detergents.

Rinse them well and wait for them to be completely dry before reassembling them.

Washing in a dishwasher is permitted, however, it may cause the filter material to darken: to reduce the possibility of this problem from happening, use low-temperature washes (55°C max).

To extract and insert the metal anti-grease filters see the assembly instructions.

CARBON AND ZEOLITE FILTERS (OPTIONAL) KACL.961

In normal use conditions, we recommend regenerating the zeolite-carbon filter every 18 months and replacing it after 3 years. Simply place it in a domestic oven at a temperature of 200°C for approximately 1 hour to regenerate it.

Wait until the filter cools before reassembling it.

LIGHTING

The range hood is equipped with high efficiency, low consumption LED lighting with extremely long duration under normal use conditions.

In case of failure, contact the Dealer or an authorised Servicing Department for repairs.

DISPOSAL AFTER END OF USEFUL LIFE

The crossed-out trash or refuse bin symbol on the appliance means that the product is WEEE, i.e., "Waste electrical and electronic equipment," accordingly it must not be disposed of with regular unsorted waste.

ed waste (i.e. with "mixed household waste"), but it must be disposed of separately so that it can undergo specific processing for its re-use, or a specific treatment, to remove and safely dispose of any substances that may be harmful to the environment and remove the raw materials that can be recycled. Proper disposal of these products contributes to saving valuable resources and avoid potential negative effects on personal health and the environment, which may be caused by inappropriate disposal of waste.

You are kindly asked to contact your local authorities for further information regarding the designated waste collection points nearest to you. Penalties for improper disposal of such waste can be applied in compliance with national regulations.

INFORMATION ON DISPOSAL IN EUROPEAN UNION COUNTRIES

The EU WEEE Directive was implemented differently in each country. Accordingly, if you wish to dispose of this appliance, we suggest contacting your local authorities or dealer to find out the correct method of disposal.

INFORMATION ON DISPOSAL IN NON-EUROPEAN UNION COUNTRIES

The crossed-out trash or refuse bin symbol is only valid in the European Union: if you wish to dispose of this appliance in other countries, we suggest contacting your local authorities or dealer to find out what the correct method of disposal is.

The Manufacturer reserves the right to make changes to the equipment at any time and without prior notice. Printing, translation and reproduction, even partial, of this manual are bound by the Manufacturer's authorisation.

The Manufacturer reserves the right to make changes to the equipment at any time and without prior notice. Printing, translation, and reproduction, even partial, of this manual are bound by the Manufacturer's authorization.

Technical information, graphic representations, and specifications in this manual are provided for informational purposes only and may not be disclosed.

ACTIVE CARBON FILTERS (OPTIONAL) KACL.961

SAFETY PRECAUTIONS

Installation must be carried out by qualified and experienced installers in accordance with the instructions in this manual and applicable regulatory requirements.

Installations must be performed by qualified installers in accordance with the instructions in this manual and applicable regulatory requirements.

If the hood is damaged and cannot be used, disconnect the hood from the power supply and contact the distributor or an authorized service center for repair.

Do not make any electrical, mechanical, or functional modifications to the appliance.

Do not attempt to replace parts or repair the appliance yourself. Work performed by unqualified persons may cause damage, including serious damage, to the appliance and/or persons, and is not covered by the manufacturer's warranty.

SAFETY PRECAUTIONS FOR INSTALLATION

SAFETY INSTRUCTIONS

Before installing the hood, make sure that all its parts are intact and in good working order. If any damage is found, do not proceed with installation; contact the distributor instead.

If external defects are detected, do not install the hood; place it in its original packaging and contact the distributor. After installation is complete, no claims regarding external defects will be accepted.

During installation, always use personal protective equipment (e.g., protective footwear) and proceed with caution and care.

The set of fasteners (screws, washers) supplied with the hood can be used exclusively on brick walls. When installing on walls made of other materials, consider other fastening systems, taking into account the wall strength and the weight of the hood (indicated on page 2).

It should be noted that installation using fastening systems other than those supplied or not intended for this purpose may lead to electrical hazards and mechanical unreliability.

Do not install the hood outdoors or in places where it would be exposed to atmospheric conditions (rain, wind, etc.).

ELECTRICAL SAFETY

The electrical system to which the hood is connected must comply with current standards and must be grounded in accordance with the regulations in force in the country of operation; it must also comply with European standards regarding interference suppression devices.

Make sure that the voltage in the electrical system matches the rating indicated on the rating plate located inside the hood.

The socket used for connecting the hood to the power supply must be easily accessible after installation. Otherwise, a main switch must be provided in an accessible location to disconnect the hood if necessary.

Any changes to the electrical system must be performed only by a qualified electrician.

The maximum length of the screws for mounting the duct (supplied by the manufacturer) is 13 mm. The use of screws that do not comply with these instructions may lead to electrical hazards.

In case of malfunction, do not attempt to repair the appliance yourself; contact the installer or an authorized technical support center for repair.

! During installation of the hood, disconnect the appliance, remove the plug from the socket, or use the main switch.

SAFETY OF SMOKE EXHAUST

Do not connect the appliance to smoke ducts for exhausting fumes produced by combustion (boilers, fireplaces, etc.).

Before installing the hood, ensure that all requirements of the applicable standards for air exhaust outside the room are met.

WARNING: Australia and New Zealand: Range hoods and other devices for removing kitchen vapors may adversely affect the safe operation of appliances that burn gas or other fuels (including those in other rooms) due to backdraft of combustion products. These combustion products may lead to carbon monoxide poisoning. After installing the kitchen hood,

SAFETY MEASURES FOR THE USER

These safety measures are intended for your safety and the safety of others, so please read them carefully before operation or maintenance.

The manufacturer is not liable for any direct or indirect damage to people, property, or pets caused by failure to follow the instructions given in this manual.

It is important that this manual with instructions is kept with the equipment for future reference when needed.

In case of sale or transfer of the appliance to another person, ensure that the manual is also transferred so that the new user can become familiar with the operation of the hood and the corresponding warnings.

Before starting the installation of the hood, carefully read the section "SAFETY TECHNIQUES AND PRECAUTIONARY MEASURES".

TECHNICAL SPECIFICATIONS

The technical data of the device are given on the labels located inside the hood.

POSITIONING

The minimum distance between the highest part of the appliance for food preparation and the lowest part of the kitchen hood is specified in the installation instructions.

Usually, when the kitchen hood is installed above a cooking surface, this distance should be no less than 65 cm (25.6"). However, based on the EN60335-2-31 standard, the minimum distance between the cooking surface and the lower part of the hood can be reduced according to the mark indicated in the installation instructions.

If the instruction manual for the gas hob specifies a greater distance, this must be taken into account.

Do not install the hood outside rooms or in places where it would be exposed to atmospheric agents (rain, wind, etc.).

ELECTRICAL CONNECTION

(section intended only for qualified personnel)

Before performing any operations on the hood, disconnect the appliance from the electrical power supply.

Check that there are no disconnected or torn wires inside the hood:

If this is the case, contact the nearest technical support service.

The electrical connection must be carried out by qualified personnel.

The connection must be made in compliance with the requirements of current legislation.

Before connecting the hood to the electrical power supply, check that:

• The voltage in the electrical system corresponds to that indicated on the manufacturer's label, which is located inside the hood;
• The electrical connection must comply with current standards and must be able to withstand the load (see technical characteristics inside the hood); the plug and cable of the electrical connection must not come into contact with temperatures above 70°C; the electrical connection system is equipped with a proper ground connection in accordance with current standards; the plug used for connection must be accessible after installation of the hood.

In case:

The yellow-green ground wire must not be disconnected by the circuit breaker.

The manufacturer is not liable in case of failure to comply with safety regulations.

EXTERNAL DISCHARGE

EXTERNAL DISCHARGE HOOD (DUCTED)

In this version, air is discharged outside through an exhaust duct.

The exhaust pipe must have:

- Diameter not less than the diameter of the hood outlet. - A downward slope (fall) of horizontal sections to prevent condensate from returning to the motor. Minimum number of bends. Minimum possible length to avoid vibration and reduction of the hood's suction capacity.

It is necessary to insulate the pipe if it passes through cold rooms.

To prevent air from returning from outside, a non-return valve is installed, which is activated when the motor is running at 800 m³/h or more.

Suction mode:

When the hood and other appliances that use energy other than electricity operate simultaneously in the room, the negative pressure inside the room must not exceed 4 Pa (4 x 10-5 bar).

INTERNAL RECIRCULATION HOOD (FILTERING)

In this version, the air is cleaned through filters with activated carbon and then returned to the room.

If the hood is installed with the exhaust pipe, it must be mounted on the exhaust, otherwise install it as described in the installation instructions.

In this case, the check valve must be installed. Remove it if it is installed on the exhaust air outlet pipe of the motor.

INSTALLATION INSTRUCTIONS

Section intended for qualified personnel

The hood can be installed in various configurations.

The general installation steps are valid for all types of installations; it is also necessary to follow the steps indicated separately, corresponding to the required type of installation.

OPERATION

When to turn on the hood?

The hood should be turned on at least 3 minutes before starting to cook, to create an air flow for directing smoke and odors towards the suction surface.

After cooking, leave the hood on until all vapors and odors have been completely extracted. Using the timer function, you can set automatic shutdown of the hood after 15 minutes of operation.

Which speed to choose?

Speed I: keeps the air clean with low electricity consumption.

Speed II: normal working conditions.

Speed III: for strong odors and large amounts of steam.

Speed IV: rapid removal of odors and vapors.

KOrJaMbItbNJIMMeHrTbΦNJIbTpbl?

Mechanical filters must be rinsed after 30 hours of operation.

Before installing the filter, let it dry.

LIGHTING

The unit is equipped with light-emitting elements with high efficiency, low energy consumption, and long service life under normal operating conditions.

In case of breakdown or for repairs, contact the distributor or an authorized technical support center.

DISPOSAL AT END OF SERVICE LIFE

The crossed-out wheeled bin symbol on the device indicates that it belongs to the category of WEEE (Waste Electrical and Electronic Equipment), so it cannot be thrown away with unsorted waste.

That is, together with household waste, but must be taken

separately so that the operations necessary for its recycling or special treatment can be carried out in the interests of environmentally safe disposal of possible harmful materials and components that can be reused. Proper disposal of this product will help save natural resources and avoid potentially harmful effects on human health and the environment, which may occur as a result of improper disposal.

INFORMATION ON DISPOSAL IN COUNTRIES OUTSIDE THE EUROPEAN UNION

The crossed-out wheeled bin symbol is valid only in European Union countries. If you wish to dispose of this device in other countries, we recommend contacting local authorities or the distributor for information on proper disposal.

ATTENTION!

The manufacturer reserves the right to make changes to the device at any time without prior notice. Printing, translation, and reproduction, including partial, of this manual are possible only after obtaining prior permission from the manufacturer.

Technical information, graphic images, and specifications provided in this manual are for reference only and are not subject to disclosure.

The manual has been compiled in Italian; the manufacturer is not responsible for possible errors or translation mistakes.

SAFETY INSTRUCTIONS AND WARNINGS

SAFETY INSTRUCTIONS AND WARNINGS

EXTRACTOR HOOD WITH EXTERNAL EXHAUST

inside the hood:

EXTRACTOR HOOD WITH INTERNAL RECIRCULATION (FILTERING)

WHEN SHOULD THE HOOD BE TURNED ON?