VT8820 - Fan SOLAC - Free user manual and instructions

USER MANUAL VT8820 SOLAC

• Read these instructions carefully before using your appliance, and keep them for future reference.
• Check that the voltage on the specifications plate matches the mains voltage in your home.
• Remove all elements used for protection during transport or for sales promotions, such as paper or plastic bags, plastic sheets, cardboard and stickers from inside or outside the appliance.
• Do not introduce any object inside the appliance. Position the appliance away from objects that could penetrate the grilles.
• Never immerse the appliance in water or any other liquid. Do not put near a bathtub, shower or swimming pool.
• Do not position the device near an open flame or inflammable gases.
• Do not place the cable under carpets or any other kind of material.
• While the appliance is in operation, keep out of reach of children, animals and disabled people. If the appliance is used in their presence, keep a watchful eye on such operations.
• The appliance is destined solely for home use; it may not be used for industrial purposes.
• Unplug when not in use.
• If the appliance does not work properly or if the power lead is damaged, take it to a Specialised Technical Service Centre.
• If the power cable is damaged, it should be replaced by the manufacturer or by your after-sales service shop or similar qualified personnel to prevent possible hazards.
• Before starting the appliance, check that it is on a stable surface and is in its normal operating position (on its base).

WARNING!!: When you want to dispose of the appliance, NEVER throw it in the rubbish. Take it to your nearest RECYCLING POINT or waste collection centre for treatment. If you do that, you will be helping to look after the environment.

MAIN COMPONENTS

1. Front grille
2. Hood

3. Blades

4. Ring

5. Rear grille
6. Connecting ring
7. Fixing plate
8. Fan body
9. Handle
10. Oscillation button
11. Stop switch
12. Low power switch
13. Medium power switch
14. High power switch
15. Turn-off timer
16. Telescopic tube
17. Height adjustment ring
18. Fixing screw
19. Base
20. Telescopic tube base
21. Shaft protector

ASSEMBLY

Assembling the base

• Remove the base (19) and the telescopic tube (16) from its cavity. Introduce the base of the telescopic tube (20) into the base so that its flanges enter the spaces in the base (19). To join the pieces, turn the tube (2) clockwise as far as it will go.
• Extract the telescopic tube (16) to the desired height and adjust the height of the fan using the height regulation ring (17).
• Fit the fan body (8) on the tube (16) and attach it by unscrewing the fixing screw (18) slightly so that the telescopic tube (16) penetrates the body of the fan ), then tighten the fixing screw again and check that both pieces are attached.

Assembling the grille and the blades

• Remove the motor shaft hood (2) and ring (4), and also remove the shaft protector (21) between them. Fit the rear grille (5) over the shaft (8) so that the projections on the motor shaft coincide with the orifices on the rear grille (5)Fig 1.
  Fix the rear grille to the fan body using the ring (4), tightening it in a clockwise direction. Fig 2.

• Insert the blades (3) so that the slits on their upper parts meet the projections on the fan body (8). Fig 3
  Fix the blades turning the hood (2) anticlockwise. Check that they turn correctly.

• Fit the front grille (1), inserting the rear grille in the guide in the connecting ring (6). You will hear a "click". The fixing plate (7) must appear to be centred in the lower section.

• Close the fixing plate (7) and tighten the safety screw.

USERINSTRUCTIONS

• Press the desired air speed switch to start the fan: low (12), medium(13) or high (14).
• The fan will stop when the off switch (11) is pressed.
• To cause the fan to oscillate horizontally, press the button (11), to stop the oscillation, gently pull the button up.
• The fan may also be inclined at an angle of 45^ to the vertical. Adjust this inclination pressing gently on the upper part of the motor shaft (8), forwards or backwards. Fig. 4
• If the time-off timer (15) is not used when the fan is in operation, it must stay in position I.

Turn-off timer

• This timer (15) allowed the time for which the fan is to remain in operation to be set, up to a maximum of 2 hours. Turn the timer to select the desired period of time, after which the fan will automatically switch off.

CLEANING AND MAINTENANCE

• Your appliance must be disconnected from the mains before any cleaning operation is performed.
• Clean with a slightly damp cloth.
• Never immerse the appliance in water or any other liquid. Check that no drops of liquid enter the motor area.
• Do not use solvents or abrasive cleaners to clean the device, since they could damage its plastic parts.
• When the appliance is not in use it should be kept in a damp-proof location.

ATTENTION

LIMPEZA E MANUTENÇÂO