HADG9DCS56B - Range hood HAIER - Free user manual and instructions

Product type	Chimney hood
Brand	Haier
Model	HADG9DCS56B
Width	90 cm
Depth	50 cm
Height (min-max)	60-110 cm
Net weight	16 kg
Power supply	220-240 V / 50 Hz
Maximum extraction rate	650 m³/h
Noise level (max)	65 dB(A)
Lighting	LED, 2 x 3 W
Grease filter type	Aluminum mesh, washable
Charcoal filter	Optional, for recirculation mode
Number of speeds	3 + intensive
Controls	Electronic push buttons
Installation type	Wall-mounted or ducted/recirculation
Energy class	A
Annual energy consumption	35 kWh/year
Warranty	2 years
Compatible duct diameter	150 mm
Remote control	Not included

Frequently Asked Questions - HADG9DCS56B HAIER

How do I install the Haier HADG9DCS56B hood?

Installation should be done by a qualified professional. Ensure the hood is mounted at least 65 cm above an electric hob or 75 cm above a gas hob. Follow the installation manual for wall mounting and ducting.

How often should I clean the grease filters?

Clean the aluminum mesh filters every 2-3 months, or more frequently if the hood is used heavily. Wash them in warm soapy water or in the dishwasher at low temperature. Ensure they are completely dry before reinserting.

Can I use the hood without a charcoal filter?

Yes, in extraction (ducted) mode, a charcoal filter is not needed. If you use recirculation mode, you must install a charcoal filter to absorb odors.

The hood is noisy. Is that normal?

Noise levels depend on the speed. At maximum speed, the hood can reach up to 65 dB(A). Ensure the ducting is not blocked and the filters are clean. If noise persists, check for loose parts.

How to replace the LED lights?

The LED lights are integrated and should be replaced by a qualified technician. Contact Haier customer service for assistance.

What is the warranty period?

The Haier HADG9DCS56B comes with a standard 2-year warranty. Extended warranty may be available depending on the retailer.

Can I control the hood remotely?

No, this model does not include remote control. It is operated via push buttons on the front panel.

How do I reset the filter saturation indicator?

After cleaning or replacing filters, press and hold the speed button for 3 seconds until the indicator light turns off.

What is the maximum duct length?

For optimal performance, the duct length should not exceed 3 meters with minimal bends. Use a smooth duct of 150 mm diameter.

How do I switch between extraction and recirculation mode?

The hood is set to extraction mode out of the box. For recirculation, purchase a charcoal filter kit and install it according to the manual. The mode change does not require any electrical modification.

USER MANUAL HADG9DCS56B HAIER

INSTALLATION AND USER'S MANUAL

CONTENT

INTRODUCTION 03

SAFETY PRECAUTION 03

ELECTRICAL INSTALLATION 05

SPECIFICATION 06

INSTALLATION (VENT OUTSIDE) 07

INSTALLATION (VENT INSIDE) 16

DESCRIPTION OF COMPONENTS 17

OPERATION 17

MAINTENANCE 18

TROUBLESHOOTING 19

CONFORMITY WITH DIRECTIVES 19

ENVIRONMENTAL PROTECTION 20

INTRODUCTION

Thank you for choosing this cooker hood.

This instruction manual is designed to provide you with all required instructions related to the installation, use and maintenance of the appliance. In order to operate the unit correctly and safely, please read this instruction manual carefully before installation and usage.

The cooker hood uses high quality materials, and is made with a streamlined design. Equipped with large power electric motor and centrifugal fan, it also provides strong suction power, low noise operation, non-stick grease filter and easy assembly installation.

SAFETY PRECAUTION

☐ Never let the children operate the machine. ☐ The cooker hood is for home use only, not suitable for barbecue, roast shop and other commercial purpose. ☐ The cooker hood and its filter should be clean regularly in order to keep in good working condition. ☐ Clean the cooker hood according to the instruction manual and keep the unit from danger of burning. ☐ Forbid the direct baking from the gas cooker. Please keep the kitchen room a good convection. Before connecting this appliance check that the power supply cord is not damaged. A damage supply cord must be replaced by qualified service personnel only. ☐ There shall be adequate ventilation of the room when the range hood is used at the same time as appliances burning gas or other fuels; ☐ The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels; ☐ Regulations concerning the discharge of air have to be fulfilled. Children should be supervised to ensure that they do not play with the appliance. ☐ Do not flambé under the range hood. ☐ The range hood is not intended to be installed over a hob having more than four hob elements

• These shall be adequate ventilation of the room when the range hood is used at the same time as appliances burning gas or other fuels (not applicable to appliances that only discharge the air back into the room);
• the details concerning the method and frequency of cleaning.
• there is a fire risk if cleaning is not carried out in accordance with the instructions;
• do not flame under the range hood;
• CAUTION: Accessible parts may become hot when used with cooking appliances.

Electrical Shock Hazard

☐ Only plug this unit into a properly earthed outlet. If in doubt seek advice from a suitably qualified engineer. ☐ Failure to follow these instructions can result in death, fire, or electrical shock.

The lamp used in this product is not suitable for use in the lighting of a room.

The purpose of this lamp is to provide illumination for using the product.

Electrical Installation

All installation must be carried out by a competent person or qualified electrician. Before connecting the mains supply, ensure that the mains voltage corresponds to the voltage on the rating plate.

Direct Connection

The appliance must be connected directly to the mains using an omnipolar circuit breaker with a minimum opening of 3mm between the contacts.

The installer must ensure that the correct electrical connection has been made and that it complies with the wiring diagram.

The cable must not be bent or compressed.

Regularly check the power plug and power cord for damage. If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.

WARNING: This is a Class I appliance and MUST be earthed. This appliance is supplied with a 3 core mains cable coloured as follows:

Brown = L or Live

Blue = N or Neutral

Green and Yellow = E or Earth

The fuse must be rated at 3 Amps.

Standard Installation Accessories List

Spec.	Illustration Picture	Qty
Hood body 1
Lower chimney (500mm)		1
Upper chimney (500mm)		1
Upper chimney bracket		1
Lower chimney bracket		1
Cooker hood bracket		1
φ8 rawl plugs φ8×φ6 white color		9
Screw (ST4 * 30 mm)		9
Screw (ST4 * 8 mm)		6
Air outlet		1
Carbon filter		2

INSTALLATION (wall mounting)

If you have an outlet to the outside, your cooker hood can be connected as below picture by means of an extraction duct (enamel, aluminum, flexible pipe non flammable with an interior diameter of 150mm)

1. Before installation, turn the unit off and unplug it from the outlet.

1. The cooker hood should be placed at a distance of 65~75cm above the cooking plane for best effect.

INSTALLING THE HOOD

Position the hood at the desired height respecting the minimum height above the hob.

Mark the location of the wall bracket. (Place the holes between 700 and 800 mm above the worktop) Remove the hood and position the wall bracket to mark the locations of the holes on the wall.

Drill the 3 holes in the wall to insert the appropriate fastening system (screw ST4x30mm).

Hang the hood in the notches of the wall bracket.

INSTALLING THE HOOD

Once the hood is in place, locate the location of the 4 additional wall mount screws as shown in the following diagram.

Remove the hood to puncture the wall and install wall plugs.

Secure the body of the hood with 4 screws of 4 mm in diameter using dowels adapted to your wall.

If the extraction mode is selected, place the exhaust air duct on the air outlet as shown.

INSTALLING THE HOOD

Attach the lower chimney support to the lower chimney as shown.

Use 2 screws ST4x8mm.

(Do not over tighten the screws, make sure the upper chimney can slide easily into the lower chimney)

Insert the upper chimney into the lower chimney.

Position the bottom chimney in the appliance, then mark the holes on the wall.

Remove the lower chimney, then drill holes in the wall: hole for screw diameter 8 mm

Use the dowels adapted to your wall

INSTALLING THE HOOD

Install the lower chimney, then screw it to the wall with 2 screws of diameter 8 mm

Then pull the upper chimney upwards to the desired height. Mark the locations of the mounting holes of the upper chimney support.

Lower the upper chimney and then drill holes in the wall.

Insert the dowels adapted to your wall

INSTALLING THE HOOD

Secure the wall bracket of the upper chimney to the wall using the selected dowels (8 mm screws recommended).

Reassemble the upper chimney and fix it to the wall bracket with 2 screws ST4x8mm

Fasten the lower chimney to the lugs of the kitchen hood using 2 screws ST4x8mm.

Standard Installation Accessories List

Spec.	Illustration Picture	Qty
Air Deflector		1
Bracket		1
φ8 rawl plugs φ8×φ6 white color		2
Screws ST4.0×30		2
Screws ST3.5×12		2

INSTALLATION (AIR DEFLECTOR FOR T-SHAPE, CURVED GLASS, FLAT GLASS MODELS):

Air deflector is mentioned as included and not optional.

1. Fix the bracket to the T-shaped plastic outlet with 2pcs ST3.5x12mm screws provided as shown below:

1. Drill 2 holes on the wall to accommodate the wall plugs, then screw and tighten the bracket onto the wall with 2pcs ST4x30mm screws provided.

1. Attach the exhaust pipe onto the air outlet of the cooker hood as shown below:

1. Install the chimney to the unit and fix it.

Please kindly be noted: T-shaped plastic outlet and v-flaps cannot be used at the same time. You can use them in two ways: 1) Add v-flap on existing outlet; 2) Use T-shaped plastic outlet, no add v-flap.

Note: The product is provided with v-flap accessory. This accessory is not mandatory for installation, operation and use of the product.

INSTALLATION (VENT INSIDE)

If you do not have an outlet to the outside, exhaust pipe is not required and the installation is similar to the one shown in section "INSTALLATION (VENT OUTSIDE)".

Activated carbon filter can be used to trap odors.

In order to install the activated carbon filter, the grease filter should be detached first. Press the lock and pull it downward.

Plug the activated carbon filter into the unit and turn it in clockwise direction. Repeat the same on the other side.

NOTE:

Make sure the filter is securely locked. Otherwise, it would loosen and cause dangerous. When activated carbon filter attached, the suction power will be lower.

OPERATION

STANDBY MODE.

After plugging in, all lighting and the system are in STANDBY MODE.

1 Low Speed button

It is used for ventilation in the kitchen. It is suitable for simmering and cooking that do not produce much steam.

2 Medium Speed button

The airflow speed is ideal for ventilation during standard cooking operations.

3 High Speed button

When high density of smoke or steam is produced, press the high-speed button for effective ventilation.

B Booster function

This hood has a booster function. To activate the booster, press

B to speed 4, entering the highest speed while the hood is in use, and it will increase speed for 5 minutes before slowing down again.

Light

Short press for lighting on and off.

Quick timer: Long press the light button and hold for 3 seconds; the fan speed buttons will flash and enter a 5-minute countdown. After 5 minutes, the motor and light will turn off automatically with three buzzer sounds.

MAINTENANCE

Before cleaning switch the unit off and pull out the plug.

I. Regular Cleaning

Use a soft cloth moistened with hand-warm mildly soapy water or household cleaning detergent. Never use metal pads, chemical, abrasive material or stiff brush to clean the unit.

II. Monthly Cleaning for Grease Filter

ESSENTIAL: Clean the filter every month can prevent any risk of fire.

The filter collects grease, smoke and dust..... so the filter is directly affecting the efficiency of the cooker hood. If not cleaned, the grease residue (potential flammable) will saturate on the filter. Clean it with household cleaning detergent.

III. Annual Cleaning for Activated Carbon Filter

Apply SOLELY to unit that installed as a recirculation unit (not vented to the outside). This filter traps odors and must be replaced at least once a year

depending on how frequent the cooker hood used.

IV. Changing a light bulb

Remove the screws on the glass, take off the hood glass. Find the bulb that requires replacement, you will find it located in the light fixture which is inside the exposed section of the canopy.

Disconnect the light wiring point and remove the bulb holders and wiring from the hood. Important: It's not possible to replace the bulbs individually, it will be necessary to obtain the bulbs, bulb holders and wiring as a complete part. (LED light: MAX 1.5W)

Fit the replacement bulbs, bulb holders and wiring in the same manners as the originals. Then reconnect the light wiring point.

Refit the hood glass and fasten the glass screws. Make sure the screws are fully tightened.

TROUBLESHOOTING

Fault	Cause	Solution
Light on, but fan does not work	The fan blade is jammed.	Switch off the unit and repair by qualified service personnel only.
	The motor is damaged.
Both light and fan do not work	Halogen light bulb burn.	Replace the bulb with correct rating.
	Power cord looses.	Plug in to the power supply again.
Serious Vibration of the unit	The fan blade is damaged.	Switch of the unit and repair by qualified service personnel only.
	The fan motor is not fixed tightly.	Switch off the unit and repair by qualified service personnel only.
	The unit is not hung properly on the bracket.	Take down the unit and check whether the bracket is in proper location.
Suction performance not good	Too long distance between the unit and the cooking plane	Readjust the distance to 65-75cm

CUSTOMER ASSISTANCE SERVICE

If you cannot identify the cause of the operating anomaly, switch off the appliance and contact the Assistance Service.

PRODUCT SERIAL NUMBER. Where can I find it?

It is important you to inform the Assistance Service of your product code and its serial number (a 16 character code which begins with the number 3); this can be found on the guarantee certificate or on the data plate located on the appliance.

It will help to avoid wasted journeys to technicians, thereby (and most significantly) saving the corresponding callout charges.

This appliance is marked according to the European directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE).

WEEE contains both polluting substances (which can cause negative consequences for the environment) and basic components (which can be re-used). It is important to have WEEE subjected to specific

treatments, in order to remove and dispose properly all pollutants, and recover and recycle all materials.

Individuals can play an important role in ensuring that WEEE does not become an environmental issue; it is essential to follow some basic rules:

WEEE should not be treated as household waste;

WEEE should be handed over to the relevant collection points managed by the municipality or by registered companies. In many countries, for large WEEE, home collection could be present.

In many countries, when you buy a new appliance, the old one may be returned to the retailer who has to collect it free of charge on a one-to-one basis, as long as the equipment is of equivalent type and has the same functions as the supplied equipment.

INSTALLING THE HOOD

INSTALLING THE HOOD

CLOSING DIRECTION

NOTE:

HOOD INSTALLATION

HOOD INSTALLATION

HOOD INSTALLATION

CLOSING DIRECTION

WARNING:

Then mount the upper chimney and fix it to the wall bracket with 2 screws ST4x8mm

NOTE:

INSTALLATION (Wall mounting)

HOOD MOUNTING

HOOD MOUNTING

HOOD MOUNTING

NOTE:

1. Before installation, disconnect the appliance and unplug the power cord.

1. The extractor should be installed at a distance of 65~75 cm above the cooking surface for best performance.

HOOD INSTALLATION

Install the hood at the desired height, respecting the minimum height above the cooking surface.

Mark the location of the wall bracket (place holes between 700 and 800 mm above the work surface). Remove the hood and position the wall bracket to mark the hole positions on the wall.

HOOD INSTALLATION

If extraction mode is selected, connect the exhaust air duct to the air outlet as shown.

HOOD INSTALLATION

Remove the lower chimney, then drill holes in the wall: hole for screw diameter ∅ 8 mm.

Use wall plugs suitable for your wall.

HOOD INSTALLATION

Install the lower chimney, then secure it to the wall with 2 screws of diameter ∅ 8 mm.

Then pull the upper chimney to the desired height. Mark the positions of the mounting holes for the upper chimney bracket.

Lower the upper chimney and drill holes in the wall. Insert wall plugs suitable for the wall.

HOOD INSTALLATION

Attach the wall bracket for the upper chimney to the wall using the selected wall plugs (8 mm screws are recommended).

Reinstall the upper chimney and secure it to the wall bracket using 2 screws ST4 x 8 mm.

1. Drill 2 holes in the wall to install wall plugs, then screw and tighten the bracket to the wall using the supplied screws (2 pcs, ST4 x 30 mm).

1. Place the chimney on the unit and secure it.

Insert the activated carbon filter into the unit and turn it clockwise. Repeat the same on the other side.

Close

NOTE:

o Check that the filter is properly locked. Otherwise, it could loosen and cause a hazard.

o When the activated carbon filter is fitted, the suction power will be reduced.

DESCRIPTION OF COMPONENTS

1 2 3 B

OPERATION

STANDBY MODE.

After switching on, the entire lighting system is in STANDBY MODE.

Disconnect the wiring point and remove the bulb holders and wiring from the extractor. Important: It is not possible to replace the bulbs individually; you will need to obtain the bulbs, bulb holders, and wiring as a set. (LED light: MAX. 1.5 W)

Install the replacement bulbs, bulb holders, and wiring in the same way as the originals were installed. Then reconnect the lighting wiring point.

Reinstall the glass of the extractor and tighten the glass screws. Make sure the screws are fully tightened.

TROUBLESHOOTING

Kvar	Uzrok	Rešenje
Svetlo je uključeno, ali ventilator ne radi	Lopatica ventilatora se zaglavila.	Isključite jedinicu i angažujte samo ovlašćenog servisera za popravku.
	Motor je oštećen.
Svetlo i ventilator ne rade	Halogena sijalica je pregorela.	Zamenite je odgovarajućom sijalicom.
	Kabel za napajanje se izvukao.	Ponovo uključite uređaj u struju.
Jedinica snažno vibrira	Lopatica ventilatora je oštećena.	Isključite jedinicu i angažujte samo ovlašćenog servisera za popravku.
	Motor ventilatora nije dobro pričvršćen.	Isključite jedinicu i angažujte samo ovlašćenog servisera za popravku.
	Uređaj nije pravilno okačen na nosač.	Skinite jedinicu i proverite da li je nosač na odgovarajućem mestu.
Učinak usisavanja nije dobar	Prevelika udaljenost između uređaja i ploče za kuvanje	Podesite rastojanje na 65-75 cm.

CUSTOMER SERVICE

If you cannot identify the cause of the malfunction, turn off the appliance and contact Customer Service.

PRODUCT SERIAL NUMBER. Where is it located?

treatments aimed at removing and properly disposing of all polluting substances, as well as collecting and recycling all materials.

1. Before installation, turn off the unit and unplug it from the outlet.

1. The range hood should be installed at a distance of 65~75cm above the cooking surface for best results.

HOOD INSTALLATION

Place the hood at the desired height, respecting the minimum height above the hob.

HOOD INSTALLATION

After the hood is positioned, locate the place for 4 additional wall mounting screws as shown in the following diagram.

Remove the hood to drill the wall and insert wall plugs.

HOOD INSTALLATION

Remove the lower chimney, then drill holes in the wall: hole for screw diameter ∅ 8 mm Use wall plugs suitable for your wall

HOOD INSTALLATION

Install the lower chimney, then attach it to the wall using 2 screws with a diameter of ∅ 8 mm.

INSTALLING THE HOOD

Attach the wall bracket for the upper chimney to the wall using the selected dowels (8 mm screws are recommended).

Reinstall the upper chimney and attach it to the wall bracket using 2 screws ST4x8mm.

Attach the lower chimney to the tabs of the kitchen hood using 2 screws ST4x8mm.

List of standard installation equipment

Spec.	Slika ilustracije	Kol.
Zračni deflektor		1
nosač		1
ø8 zidni čepoviø8 × ø6 bijela boja		2
Vijci ST4.0x30		2
Vijci ST3.5*12		2

INSTALLATION (AIR DEFLECTOR FOR T-SHAPED, CURVED GLASS, FLAT GLASS MODELS):

1. Drill 2 holes in the wall to insert the wall plugs, then screw and tighten the bracket to the wall using the supplied screws, 2 pieces ST4x30mm.

1. Install the chimney onto the unit and secure it.

Note: The plastic T-shaped outlet and the v-flap cannot be used simultaneously. You can use them in two ways: 1) Add the v-flap to the existing outlet; 2) Use the plastic T-shaped outlet without adding the v-flap.

Note: The product is equipped with accessories for the v-flap. This accessory is not mandatory for installation, operation, or use of the product.

INSTALLATION (INTERNAL VENT)

The activated carbon filter can be used to prevent the spread of unpleasant odors.

To install the activated carbon filter, you must first detach the grease filter. Press the latch and pull it downwards.

Connect the activated carbon filter to the unit and turn it clockwise. Repeat the same on the other side.

NOTE:

1. Before installing the range hood, switch it off and disconnect it from the power supply.

1. For optimal performance, install the range hood 65-75 cm above the cooking surface.

HOOD INSTALLATION

HOOD INSTALLATION

HOOD INSTALLATION

Remove the lower duct, then drill holes in the wall: a hole for the screw diameter Φ8 mm.

Use wall plugs suitable for your wall.

HOOD INSTALLATION

Install the lower duct, then screw it to the wall with 2 screws of diameter Φ8 mm.

HOOD INSTALLATION

Reassemble the upper duct and attach it to the wall bracket with 2 screws ST4 x 8 mm.

1. Install the duct onto the unit and secure it.

Insert the activated carbon filter into the unit and turn it clockwise. Repeat the same on the other side.

CLOSING

NOTE:

NOTE: