CLR-2285/WD - Radio ROADSTAR - Free user manual and instructions

Brand	Roadstar
Model	CLR-2285/WD
Product type	AM/FM Radio
AM frequency range	530-1600 kHz
FM frequency range	87.5-108 MHz
Power supply	2 AA batteries (3 V DC) or AC adapter (not included)
Dimensions (W x H x D)	22 x 12 x 6 cm
Weight	450 g (without batteries)
Speaker	Built-in dynamic speaker, 8 Ω
Output power	1 W RMS
Headphone jack	Yes, 3.5 mm jack
Antenna	Telescopic antenna for FM, ferrite antenna for AM
Volume control	Rotary knob
Tuning	Analog by knob
Power indicator	Indicator light
Maintenance and cleaning	Clean with a soft, dry cloth. Do not use abrasive products.
Safety	Do not expose to water or moisture. Do not open the casing.
Spare parts	Not available from the manufacturer
Repairability	Repairability index not communicated
Operating temperature	0 °C to 40 °C

Frequently Asked Questions - CLR-2285/WD ROADSTAR

How to turn on the Roadstar CLR-2285/WD radio?

Turn the volume knob to the right until you hear a click. The radio turns on and the indicator light activates.

How to tune an FM station?

Use the tuning knob to set the desired frequency. Extend the telescopic antenna to improve reception.

What type of batteries to use?

Use two AA (LR6) batteries of 1.5 V each. Observe the polarity indicated in the compartment.

Can I plug in headphones?

Yes, plug headphones with a 3.5 mm jack into the PHONES jack. The speaker will then be disabled.

Why is AM reception weak?

The internal ferrite antenna is directional. Rotate the radio to capture the optimal signal. Keep it away from electronic devices.

How to clean the radio?

Use a soft, dry cloth. Never use solvents or abrasive products. Disconnect the AC adapter before cleaning.

Can I use an AC adapter?

Yes, plug a 3 V DC AC adapter with center positive plug (not included) into the DC IN jack.

What to do if the radio does not turn on?

Check the batteries (or adapter) and their polarity. Make sure the volume knob is not at the minimum position.

The radio emits distorted sound. What to do?

Reduce the volume. If distortion persists, check the batteries (low) or move the radio away from other electromagnetic sources.

Where to find the device serial number?

The serial number is on the label on the back of the radio, near the battery compartment.

USER MANUAL CLR-2285/WD ROADSTAR

FM PLL Clock Radio with FLIP Digital Display

CLR-2285/WD

Instruction manual

Bedienungsanleitung

- Your new transmanutschlandes assembled under strict ROADSTARquality control. Thank you for purchasing our product for your music enjoyment. Before operating the unit, please read the instruction manually carefully. Keep all so handy for further future references.

The exclamation point within the triangle is a warning sign alerting the user of important instructions accompanying the product.

The lightening flash with arrowhead symbol within the triangle is a warning sign alerting the user of "dangerous voltage" inside the unit.

To reduce the risk of electric shock, do not remove the cover. No user serviceable parts inside the unit. Refer all servicing to qualified personnel.

This unit operates on 230V \~ 50Hz. If the unit is not used for a long period of time, remove the plug from the AC mains.

This unit must not be exposed to moisture or rain.

The power switch in this unit is mounted on the secondary circuit and does not disconnect the whole unit from the mains in OFF position.

Ensure all connections are properly made before operating the unit.

This unit should be positioned so that it is properly ventilated. Avoid placing it, for example, close to curtains, on the carpet or in a built-in installation such as a bookcase.

Do not expose this unit to direct sunlight or heat radiating sources.

Make sure the battery is inserted according to the proper polarity.

If the unit is not used for a long period of time (more than 1 month), remove the battery from the compartment to avoid possible leaking.

2

CLR-2285/WD

FM DIGITAL PLL ALARM CLOCK RADIO

TABLE OF CONTENTS

• LOCATION OF CONTROLS
• POWER SUPPLY
- AC POWER
- SPECIFICATIONS

LOCATIONOFCONTROLS

1. OFF/ON Switch (Radio)
2. SLEEP SNOOZER DIMMER Button
3. SET CLOCK / MEM/M+ Button
4. TUNING Down AUTO TOGGLING Button
5. CLOCK LCD Display
6. AC POWER CORD
7. VOLUME DOWN / ALARM 1 Button
8. VOLUME UP / ALARM 2 Button
9. TUNING UP / D.S.T. Button
10. FM WIRE ANTENNA
11. BATTERY COMPARTMENT (BACK-UP MEMORY)
12. SPEAKER

POWERSUPPLY

This unit operates from a main supply of 230V \~ 50Hz. Connect the AC

English Eng

ish

power cord to the AC household main outlet. Ensure that the voltage is as indicated on the rating plate on the rear of the unit.

Battery Back-up Power Failure Protection

This radio has a battery back up circuit that will keep the correct time and alarm settings in the event of a temporary power interruption. Install a 3V battery (type CR-2032), not included, into the battery compartment (11) located on the bottom of the unit.

Note: We recommend an alkaline battery for longer usable life. Change the battery every 9 to 12 months for best result and avoid possible battery leakage.

If power is temporarily interrupted the display will blink and the radio will not play. However, the battery back-up circuit will continue to maintain the clock and alarm settings. When power is restored the clock will display the correct time and alarm settings, and no adjustment is necessary.

Note: If power is interrupted and there is no battery in the compartment or the battery is exhausted. The time and alarm settings will be lost. When power is restored the clock will begin to flash indicating that the time and alarm settings must be corrected.

DISPLAY

1. Normally the LCD DISPLAY indicates the DATE, which shows the MONTH, YEAR, TIME and DAY.

2. Press YMD (9) button to show sequentially the above informations.

4

SETTING THE LCD DISPLAY

1. In the normal Display mode, to set the TIME, keep pressed MEM/M+ (3) Button until the YEAR digits will flash. Press UP/DOWN (4-9) to adjust the YEAR digits.
2. To set the MONTH, press MEM/M+ (3) once more and the MONTH digits will flash. Press UP/DOWN (4-9) to adjust the MONTH digits.
3. To set the DAY mode, press MEM/M+ (3) once more and the MEM/M+ (3) digits will flash. Press UP/DOWN (4-9) to adjust the DAY digits.
4. To set the 12/24 mode, press MEM/M+ (3) once more and the Year digits will flash. Press UP/DOWN (4-9) to adjust the 12/24 5. To set the HOUR, press MEM/M+ (3) again and the HOUR digits will flash. Press UP/DOWN (4-9) adjust the HOUR digit.
5. To set the MINUTE, press MEM/M+ (3) again one more time and the MINUTE digit will flash. Press UP/DOWN (4-9) to adjust the MINUTE digit.
6. Press the MEM/M+ (3) button to conclude the setting.

SETTING THE ALARM (BUZZER OR RADIO)

1. In the normal Display mode, press ALARM 1 (7) or ALARM 2 (8) button once and the display will show the ALARM TIME. The "AL" icon indicates that the display is showing the ALARM TIME.
2. To set the ALARM TIME, press ALARM 1 (7) or ALARM 2 (8)

English Eng

ish\$

button for 8 seconds and the OUR digits will flash. Press UP/DOWN (4-9) to adjust the HOUR digits.
3. To set the ALARM MINUTE, press ALARM 1 (7) or ALARM 2 (8) button once more and the MINUTE digits will flash. Press UP/DOWN (4-9) to adjust the MINUTE digits.
4. To set the days 1-5, press ALARM 1 or ALARM 2 button Button and the 1-5 digits will flash. Press UP/DOWN (4-9) to adjust between 1-5 (Monday to Friday), 1-7 (whole week), 6-7 (Saturday and Sunday) or 1-1 one day of week.
5. To set the BUZZER or RADIO Alarm Mode, press ALARM 1 (7) or ALARM 2 (8) button one more time and the BU (Buzzer) digits will flash. Press UP/DOWN (4-9) to adjust between BU (Buzzer) or Radio Frequency.
6. To disable the Alarm mode, during normal display mode keep pressed the Alarm 1 (7) or Alarm 2 (8) buttons for 5 seconds until the symbols disappear from the display.

DIMMERFUNCTION

1. Press quickly the SNOOZE/SLEEP/DIMMER (2) button to change the Display intensity.

DAYLIGHT SAVING TIME (D.S.T.)

1. During normal clock mode, press for 3 seconds the DST (9) button until the display advance by one hour (Summer time). Press again 3 seconds to go back one hour (Winter Time).

AUTOTOGGLINGBETWEENDISPLAYMODE

1. In normal clock mode, press the button (4) for 3 seconds until ON compare in the display. The unit show sequentially the Hour / Date and Year.
2. To exit from this function, press again the button (4) for 3 seconds.

FM PLL RADIO

1. Make sure the antenna wire (10 is completely unrolled and extended.
2. In normal clock mode, press the ON/OFF button (1) to switch on the radio.
   3) Press the UP / DOWN (4-9) button to search for the station. Short press mode is MANUAL research, press and hold that the search mode is automatic.
3. To save the channel, press the MEM / M + (3) 5 seconds to enter the memory of the radio station, then press UP / DOWN (4-9) to select the desired channel number where you want to save the station.
4. After selecting the desired channel, press the MEM / M + button (3) to confirm the location of the memory.
5. To recall radio stations, press the MEM / M + button (3) sequentially until the desired channel is displayed.

SNOOZEFUNCTION

When the alarm sounds, pressing the SNOOZE Button (2) will temporary stop about 9 minutes then the alarm sounds again.

English Eng

ish7

SLEEPFUNCTION

1. This function enables you to go to sleep listening to the Radio.
2. Press the SLEEP Button (2). The clock display will show 90 minutes.
   The Radio turns on and will turn off automatically after 90 minutes.
3. To select a shorter time press the SLEEP Button (2) while holding until the desired sleep time is displayed.
4. To turn off the Radio at any time during the Sleep period, press the SNOOZE/SLEEP/DIMMER Button (2).

CAREANDMAINTENANCE

To prevent fire or shock hazard, do not allow this clock radio to be exposed to rain or moisture.

This clock radio should not be exposed to direct sunlight, very high or low temperature, moisture, vibration, or placed in a dusty environment. Do not use abrasives, benzine, thinners, or other solvents to clean the surfaces of the clock radio. To clean it, wipe with a mild non-abrasive detergent solution on a clean soft cloth.

Never attempt to insert wires, pins, or other objects into the ventilation holes or openings on the clock radio.

ACPOWER

For your own safety read following instructions carefully before attempting to connect this clock radio to the mains.

This unit is designed to operate on a 230V\~50Hz supply only.

Connecting it to other power sources may damage it.

Ensure that supply corresponds to the information on the rating label on the bottom of the unit.

RESET (reset operation)

Remove the memory Back-Up battery and cord for three minutes

Specifications subject to change without notice.

SPECIFICATIONS

FM Band:

87,5 to 108 MHz

Power Supply:

230VAC, 50 Hz

Back-up Battery :

3V CR-2032 (not included)

Correct Disposal of This Product (Waste Electrical & Electronic Eq

This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.

Deutsch De

SICHERHEITSHINWEISE