82-9600 - Kit d'installation Metra - Free user manual and instructions

USER MANUAL 82-9600 Metra

INSTALLATION INSTRUCTIONS FOR PART 82-9600

APPLICATIONS

Harley-Davidson 1998-2013

(FL models with fairings)

82-9600

KIT FEATURES

- Mounts aftermarket 6" to 6.5" speakers into factory speaker locations.

KIT COMPONENTS

- A) (2) speaker adapters • B) (6) #8 x 1" Pan-head Phillips screws

TOOLS REQUIRED

- Panel removal tool - Phillips screwdriver - Socket Wrench (T-25, T-27, 6mm or 3/16 hex)

Table of Contents

Fairing Disassembly

- Harley-Davidson FLH, batwing fairing ... 1998-2013....2-3

- Harley-Davidson Roadglide, sharknose fairing 1998-2013 4-5

Kit Assembly 6

CAUTION: Metra recommends disconnecting the negative battery terminal before beginning any installation. All accessories, switches, and especially air bag indicator lights must be plugged in before reconnecting the battery or cycling the ignition.

NOTE: Refer to the instructions included with the aftermarket radio.

METRA. The World's best kits.

metraonline.com1-800-221-0932 ELECTRONICS CORPORATION

82-9600

Fairing Disassembly

FLH/Batwing models:

1. Cover the front tender.
2. Remove (2) T-27 Torx bolts from inner fairing (under mirrors) (Figure A, step 2)
3. Remove (2) T-27 Torx bolts from outer edges of Inner tailring near the fork tubes (facing forward) (Figure A, step 3)
4. Remove (3) T-27 Torx bolts from bottom edge of windshield. (Figure A, step 4) NOTE: Windshield and fairing will be loose once these screws are removed. Use extreme caution not to damage fairing or windshield.
5. Remove windshield taking caution that the outer fairing is loose. Continued on next page

Step 4 Step 2 Step-2 Step 3

(Figure A)

82-9600

Fairing Disassembly

FLH/Batwing models: (cont.)

1. Lift away and unplug headlight to remove outer fairing. (Figure B)
2. Unbolt and remove inner fairing support brackets from each side (3/16" Allen & T-25 Torx screws).

Note the Torx screw is also a shared speaker screw. (Figure C)

1. Remove the remaining speaker screws and the speaker.

Continue to kit assembly

Technical line drawing of a mechanical assembly with no visible text or symbols

(Figure B) (Figure C)

Pure mechanical diagram showing gear and linkage components without any text or symbols

82-9600

Fairing Disassembly

Roadglide/Sharknose models

1. Loosen (6) T-25 Torx bolts from bottom, middle and top of left and right sides of the inner fairing. (Figure A)

Continued on next page

Step 1 Step 1

(Figure A)

82-9600

Fairing Disassembly

Roadglide/Sharknose models (cont.)

1. Use a 1/2" socket or box wrench to remove the (2) acorn nuts that hold each turn signal at the lower tailring. Let the signals hang loose. (Figure B)
2. Lift away the fairing, unplug the headlights and remove.
3. Remove the speaker screws and the speaker.

Continue to kit assembly

Technical line drawing of a mechanical clamp or bracket assembly (no text or symbols)

(Figure B)

82-9600

Kit Assembly

1. Using 3 of the screws in the provided hardware, mount the speaker adapter to the inner fairing. The 4th inner bottom screw locations are not used on FLH/batwing models. For Road Glide models, rotate the adapter until the notches in the adapter do not hit the factory mounting posts and the flat spots on the outside of the adapter are toward the outer edge of the fairing. (Figure A)
2. Mount the new speaker with the hardware provided with the speakers. (Figure B)

Technical line drawing of a mechanical assembly with no visible text or symbols

(Figure A) (Figure B)

Technical line drawing of a mechanical assembly with no visible text or symbols

Metra™

82-9600

INSTALLATION INSTRUCTIONS FOR PART 99-9600

KNOWLEDGE IS POWER

enabling in the non-recognized and-species

notle culleres siessii or 1027.

503-254-6782 for more information and take place

Metra recommends MECP

certified technicians

METRA. The World's best kits."

metraonline.com1-800-221-0932 ELECTRONICS CORPORATION

Paso 4 Paso 2-Paso 2 Paso 3

(Figura A)

82-9600

Desensamble del carenado

Modelos FLH/alas de murciélago (cont.)

Technical line drawing of a mechanical assembly with no visible text or symbols

(Figura B) (Figura C)

Technical line drawing of a mechanical assembly with no visible text or symbols

82-9600

Desensamble del carenado

Modelos Roadglide/Sharknose

Technical line drawing of a mechanical clamp or bracket assembly (no text or symbols)

(Figura B)

82-9600

Ensamble del kit

Technical line drawing of a mechanical assembly with no visible text or symbols

(Figura A) (Figura B)

Technical line drawing of a mechanical assembly with no visible text or symbols

Metra™

82-9600