SO4500 - Pressure washer NILFISK - Free user manual and instructions

Product Type	High-pressure steam cleaner with vacuum and detergent injection
Brand	NILFISK
Model	SO4500
Power Supply	230 V ~ Single-phase, 1950 W
Steam Pressure	4.5 bar
Max Steam Temperature	Up to 170 °C (135 °C at source)
Heating Body Capacity	1.8 L
Cold Water Tank Capacity	5 L
Steam Hose Length	4 m
Power Cord Length	10 m
Weight	12 kg
Main Functions	Steam cleaning, detergent injection, vacuum
Included Accessories	Floor brush, large nozzle, fine nozzle, extension tubes (x2), window squeegee, triangular brush, circular brush 55 mm, fine brushes brass (x5) and nylon (x5)
Steam Adjustment	Yes, via regulation knob
Indicator Lights	Heater ready, steam ready, cold water filling, LED temperature display
Safety	Automatic heating body shut-off if tank empty, thermal cut-out in case of overheating, On/Off switch with indicator
Daily Maintenance	Grease the O-ring seals of the hose, wipe the body, wash accessories with soapy water
Weekly Maintenance	Inspect the cable and hose, check the casters
Warranty	12 months subject to conditions (wear parts excluded)
Professional Use	Yes, designed for professional environment

Frequently Asked Questions - SO4500 NILFISK

What to do if the machine does not turn on?

Check that the power cord is plugged into a working outlet and that the On/Off switch is pressed (the indicator should light up). If the problem persists, check the 13 A fuse and replace it if necessary.

Why is there no steam?

Make sure the heating body is hot (wait for the Ready for steam indicator to light up). Check that the cold water tank is not empty (the filling indicator lights up and a buzzer sounds). Fill the tank if necessary. Finally, turn the steam regulation knob to an intermediate position.

Water comes out instead of steam, what to do?

This usually happens if the heating body is not hot enough. Wait for the Ready for steam indicator to light up. If the problem persists, press the steam switch for about one minute even if only water comes out: this will restart the heating.

How to clean accessories after use?

Always wash the accessories in warm soapy water. Never immerse them in water. Wipe the machine body with a clean, damp cloth.

What types of detergents to use?

Use only detergents and cleaning products approved by Nilfisk. The use of unauthorized products voids the warranty.

Can the machine be used on all types of surfaces?

No, avoid heat-sensitive surfaces such as velvet, satin, leather or fragile plastics. Always test on an inconspicuous area. The steam can reach over 170 °C.

How to maintain the steam hose seals?

Grease the O-ring seals on the steam hose before each connection. In case of leakage, replace the seals and grease again.

What to do in case of steam leak at the front connection?

The O-rings are probably cracked or worn. Replace them and grease them carefully. Make sure to grease the seals before each use to avoid this problem.

The machine stops during use, why?

If the Cold water filling indicator lights up, the tank is empty. Fill it within 30 minutes, otherwise the heating body stops automatically. If the power is interrupted, check the fuse or outlet.

How to store the machine?

Wrap the power cord around the handle before storing. Store the hose and accessories neatly. Never immerse the machine or the hose in water.

USER MANUAL SO4500 NILFISK

1. Cold Water Tank
2. Steam Control
3. Steam Hose Socket
4. Caster with Brake
5. Caster No Brake
6. Serial Number

B

1. On/Off Switch
2. Heater On LED
3. Steam Ready LED
4. Cold Water Refill LED
5. Temperature Display LED

Attachments

These Parts were carefully packed at Nilfisk. Please check all accessories on receipt. If any parts are missing or damaged please contact the company in which you purchased this machine, within 7 days of purchase quoting your serial number on the back of the machine.

1. 4 Centre Steam Only Hose
2. Floor Brush
3. Large Brush Elbow
4. Large Nozzle
5. Detail Brush Nozzle

6. Detail Brass Brush x 5

7. Extension Tube x 2

8. Triangular Brush
9. Window Squeegee
10. Curved Nozzle
11. Detail Nylon Brush x 5
12. 55mm Round Brush

C

1.

2.

3.

4.

5.

6.

7

8.

9.

10.

11.

12.

Guidance

Congratulations

We would like to take this opportunity to thank you for your purchase of the Nilfisk steam only cleaner.

The SO4500 is manufactured in the EU to the highest quality Standards

This instruction manual contains all of the necessary information to operate and maintain this machine. Please read this instruction manual carefully before you start using or carrying out any maintenance on the machine.

If you use this machine correctly as stated in this instruction manual this machine will fulfil all your steam cleaning needs.

• This machine is intended for use in a commercial cleaning environment. If you do not follow the instructions contained in this manual, situations may arise which may be dangerous or harmful to the machine or the person operating the machine. Read this manual carefully so that you know when such situations can arise.
• Ensure that all operators of this machine are fully trained on how it works.
• Report any problems or damage to the machine immediately to the supplier or a Nilfisk approved supplier for this product. Do not operate the machine until the problem or damage has been resolved.

Getting the Best Results

• Operate the machine in accordance with the instruction manual

• Maintain the machine in accordance with instruction manual

• Use only parts supplied by Nilfisk approved distributors

• Use only detergents and cleaning products in the solution tank which have been approved by Nilfisk

Keep this manual in a safe place for future reference and ordering of spare parts

Installation

Warnings

• Lift the machine out of the box.
• Check all accessories are present in the box as shown in Diagram C

This machine has been designed with your safety in mind; however it is important that you observe the following points for safe operation during the operating procedure

This is an electrical product - Do not use in wet weather or allow the machine to get wet.
- Do not discharge steam towards people, danger of scolding. Or towards equipment containing electrical components
- Never allow children to play with this appliance.
- Do not use the machine for other purposes that it was built for.
- Please remember that the steam cleaner operates at temperatures in excess of 170^ . Never use it on objects, which cannot resist the temperature (delicate materials, fabrics, plastics, wood etc). Where any doubt exists check carefully on a part of the material where minor marks will not matter.
- Do not operate the machine or carry out any maintenance out on it

Unless you are trained and authorised to do so
Unless you have read and thoroughly understand this instruction manual.

Operating Procedure

1. Fill the cold water tank (Number 1 Diagram A) with clean cold water only.

!! Anything other that clean cold water used in the

Water tank will void the manufacturer's warranty.

1. Connect the Steam Hose (Number 1 Diagram C) to the front of the machine (Number 3 Diagram A) ensuring it is pushed in all the way and the pin on the flap locks into the hole on the hose.

!! Grease "O" rings on steam pin before connecting.

!! To release the steam hose, lift the flap and pull.

Operating Procedure cont....

1. Plug the power cable into a 240 Volt supply.

!! Inspect the electric cable before every use. If the cable becomes damaged at anytime the complete cable must be replaced by a Nilfisk approved distributor.
!! Never touch the power cable or plug with wet hands
!! Always unplug the machine when

i. The machine is not in use
ii. Cleaning the machine
iii. Any maintenance work is being carried out

1. Switch the On/Off switch (Number 7 Diagram B) to the ON position. The Heater On light LED (Number 8 Diagram B) will illuminate.
2. Allow approximately 5 minutes for the boiler to heat the water

3. When the Steam Ready LED (Number 9 Diagram B) illuminates the machine is ready to be used.

4. The handle controls are now active.

The fan switch on the hose handle will release steam when pressed.
- Pressing the detergent switch located on the top of the handle will activate the detergent pump. Hold the switch as long

as you need to dispense the detergent. Releasing the switch will stop the detergent supply.

1. The steam output can be adjusted by the steam control knob (Number 2 Diagram A)
2. Choose and fit the required accessory (Diagram C) to the hose handle.

!! When changing accessories during use please note these will be hot.

During Use

Cold Water Tank Empty(Number 1 Diagram A)

1. Refill the cold water tank when the refill cold water LED (Number 11 Diagram B) is illuminated. A buzzer will sound and the steam will no longer come out of the nozzle when the steam switch on the handle is pressed.
2. The pumps will not work when the cold-water tank is empty.
3. Once the cold water refill LED is illuminated the boiler heater will remain on for 30 minutes. If the cold-water tank is not refilled within 30 minutes and the machine is left powered on the boiler heater will switch off.

Safety Precautions

This machine is to be used by trained operatives only

DO

• Check the cable and plug are safe and intact before plugging the machine in.
• Place cleaning in progress signs where necessary
• Point the steam nozzle away from your body during use
• Clean machine after each use

DON'T

• Use the machine near people, children or animals
• Point steam at electrical apparatus
• Use the machine to clean the machine down
• Do not use on Velvet, satin or leather
• Leave the machine unattended

Maintenance

Warning: Disconnect the machine from the mains before cleaning or carrying out any maintenance work.

Daily Maintenance

To be carried out every day or every 8 hours of operation.

1. Grease "O" rings on the steam pin in the steam hose.
2. Wipe down the body of the machine with a clean damp cloth
3. Always wash the accessories in hot soapy water

DO NOT IMMERSE THE MACHINE OR HOSE IN WATER

1. Wrap the power cable around the handle before storage.

Weekly Maintenance

To be carried out every week or every 50 hours of operation.

As for daily maintenance plus the following:

1. Inspect the power cable for any signs of damage. If damaged do not repair, contact the supplier of this product. Do not use until repaired.
2. Inspect the hose assembly for any signs of damage. If damaged do not repair, contact the supplier of this product. Do not use until repaired.
3. Inspect castors and wheels to ensure all securing bolts are fully tightened.

Service & Guarantee

Service

If you require a service or advice on using or maintaining your machine please contact your Nilfisk approved distributor

Guarantee

Nilfisk guarantees that if within 12 months from the date of purchase this appliance, or any parts thereof, is proved to be defective by reason of faulty workmanship or materials, we will at our option repair or replace the same free of charge for labour and materials, provided that:

• The appliance has been installed and used in accordance with our operating and servicing instructions.
• If the appliance has been serviced, maintained, repaired, modified taken apart or tampered with by any person not authorised by us, then we will not be liable under this guarantee for any fault arising from their defective workmanship.
• We shall not be liable under this guarantee for any fault in the appliance arising from the use of spare parts not supplied and recommended by us.
• Excluded from this guarantee are parts that need replacement due to normal wear and tear such as hoses, nozzles and accessories.

Technical

Technical Information

Boiler

Wattage:

Type:

Capacity:

Continuous Fill

Steam Pressure

Steam at source:

1950W

Stainless Steel

1.8 Litres

Yes

4.5 Bar

135^ C>

Electrical

Voltage

230V\~single phase

Low Voltage Controls

5V

Cord length

10m

Capacities

Boiler

1.8 Litres

Cold Water Tank

5 Litres (easy fill)

Weight

12kg

Trouble Shooting

Symptom	Possible cause	Action
No power	Not connected / Faulty socket	Check connection to wall socket and socket switch. Try in another wall socket
	On / Off switch not on	Press On / Off switch which will illuminate when on
	Fuse blown	Replace fuse with approved 13A fuse
	Unknown	Call for service
No steam	Steam Control turned down fully clockwise	Turn the control to half way
	Steamer not ready	Wait for the “Ready to steam” light to illuminate
	Clean water tank is low (beeping sound& "refill" light is lit)	Pour water into the clean water tank until the beeper stops. The steam handle will work again.
	Unknown	Call for service
No steam, Just water	Steamer not ready	Wait for the “Ready to steam” light to illuminate
	Boiler at pressure and not heating(temperature less than 110°C)	Hold the steam switch on for approximately one minute, ever if just water is coming out. This will result in the heater coming back on
	Unknown	Call for service
Steam Leaking from front socket	“O” Rings split	Change and re grease “O” Rings. To avoid this happening ensure “o” rings are grease before every use.
	“O” rings worn	Change and re grease “O” Rings. To avoid this happening ensure “o” rings are grease before every use.
	Unknown	Call for service

Legende

A

CO JE NUTNÉ PROVÁDÉT