Q: How to use the automatic FM station search on the JVC KD-R431?

The JVC KD-R431 features an automatic search function called SSM (Sequential Memory Storage) that allows you to quickly store the strongest FM stations. Using the automatic search (SSM) Here’s how to proceed: Access the TUNER menu on your car radio screen Select the SSM function The "SSM" indicator will blink during the memory storage process The device automatically scans all FM frequencies and stores the 18 strongest stations Once completed, the "SSM" indicator stops blinking This function saves you from manually searching for each station and quickly fills the memory with the best receptions available in your area.

Q: What are the 2 ohm impedance specifications for the KD-R462?

The KD-R462 has a maximum output power of 50 W × 2 when a 4 Ω subwoofer is connected. However, the recommended impedance for this model is 4 Ω to 8 Ω . Although the manual indicates a specification at 2 ohms, it is not recommended to use an impedance lower than 4 ohms for this device. Operating below this minimum impedance can cause an overload of the amplifier and damage both the receiver and your speakers. For your safety and that of your equipment, ensure that your speakers or subwoofer comply with the recommended impedance of 4 Ω - 8 Ω.

Question 1

How to fix the frozen or stuck screen issue on the JVC LT-26C31SUE?

Accepted Answer

If the screen of your JVC LT-26C31SUE television is frozen or stuck, here are the solutions to apply:

1. Check the FREEZE function

Your television has a FREEZE function (freeze frame) accessible via the remote control. Make sure you haven't accidentally activated this function, which freezes the image displayed on the screen. Press the corresponding button to deactivate it if it is active.

2. Reset the television

Completely turn off the television using the remote control
Unplug the power cable from the wall outlet
Wait at least 60 seconds
Plug the power cable back in
Turn the television back on

3. Check the display mode

The manual for this model indicates that the ZOOM function does not work in multi-image mode (twin-picture mode) and that certain display modes may create unusual behaviors. Try switching back to a standard display mode:

Access the menu via the remote control
Select the zoom option and set it to AUTO or REGULAR
Press OK to confirm

4. Check the input source

The frozen image may also result from poor signal reception:

Ensure that your antenna, cable, or source (VCR, decoder) is properly connected
Refresh the channels by accessing the automatic channel installation menu

5. If the problem persists

If the screen remains frozen after these manipulations, it is likely that a hardware failure is the cause. Contact an authorized JVC repair service or the manufacturer's customer support for a professional diagnosis.

Question 2

What is the reference and how to replace the belt of the turntable?

Accepted Answer

The manual for the JVC AL-F50B does not specify the exact reference of the drive belt or the replacement instructions. The notice only indicates that the turntable uses a belt drive.

To identify and replace the belt, you will need to:

Consult the complete JVC documentation or contact customer service (Darty, Fnac, Vanden Borre - references included in the notice)
Measure the existing belt or consult a forum specialized in JVC turntables
Entrust the replacement to a repair technician if you are not comfortable with this type of intervention

For regular maintenance, the manual recommends cleaning the turntable with a soft dry cloth.

Question 3

What happens if I forget to unplug my JVC XS-F720B speaker?

Accepted Answer

There is no major safety issue with leaving your JVC XS-F720B speaker plugged in continuously. The device is designed to operate either on battery, plugged into the mains, or both simultaneously.

When the speaker is plugged in:

The built-in battery (4,000 mAh lead-acid battery) automatically recharges
The device can remain plugged in for long periods without risk
This is actually the recommended setup for extended use at home

Battery caution: According to the manual, it is advised not to completely discharge the battery in order to prolong its lifespan. If you primarily use the speaker plugged into the mains, the battery will always be in good charge condition.

In summary, forgetting to unplug your XS-F720B poses no danger. The device will simply continue to recharge its built-in battery and will be ready for battery use when you need it.

Question 4

How to store radio stations on the JVC RA-F230W?

Accepted Answer

To store radio stations on your JVC RA-F230W, here is the recommended procedure:

Preparation

Make sure the antenna is properly connected and positioned optimally for good reception.

Storing Stations

Press the "Radio" button to select the radio source (FM or AM according to your preference).
Use the search buttons to browse available stations.
Perform an automatic search for available stations in your area.

Note: The complete PDF of this manual is currently unavailable. For detailed instructions on the precise memorization of stations and the exact programming key sequences, please refer to the user manual provided with your device or contact JVC support. However, the basic radio features described above will allow you to navigate and select the available transmitters.

Question 5

How to use the automatic FM station search on the JVC KD-R431?

Accepted Answer

The JVC KD-R431 features an automatic search function called SSM (Sequential Memory Storage) that allows you to quickly store the strongest FM stations.

Using the automatic search (SSM)

Here’s how to proceed:

Access the TUNER menu on your car radio screen
Select the SSM function
The "SSM" indicator will blink during the memory storage process
The device automatically scans all FM frequencies and stores the 18 strongest stations
Once completed, the "SSM" indicator stops blinking

This function saves you from manually searching for each station and quickly fills the memory with the best receptions available in your area.

Question 6

How to disconnect a phone from the JVC KWR910BT?

Accepted Answer

To disconnect a Bluetooth phone from your JVC KWR910BT car radio, you have several options:

Remove a specific pairing

This is the recommended method to remove a particular phone:

Press MENU
Select BLUETOOTH
Go to DELETE PAIR
Select the phone to disconnect
Confirm with YES

Reset all Bluetooth pairings

If you want to erase all stored phones at once:

Go to MENU > BLUETOOTH > SETTINGS > INITIALIZE
Confirm with YES

This action resets all Bluetooth settings and deletes all stored pairings.

Important note

Your KWR910BT can manage up to two Bluetooth phones connected simultaneously. To switch between two paired devices, repeatedly press the 📊/▼ button (outside of a call).

Question 7

How to connect an iPhone via Bluetooth to the JVC KWR910BT?

Accepted Answer

To pair your iPhone with the JVC KWR910BT car radio, follow these steps:

Turn on Bluetooth on your iPhone and start searching for available devices.
Select "JVC UNIT" from the list of detected devices.
Enter the PIN code: If prompted, enter 0000.
The car radio will display "BT PAIRING" which will blink. Confirm the pairing according to the instructions displayed.

Once the pairing is successful, your iPhone will remain registered on the device. You will then be able to use the available Bluetooth features: hands-free calls (HFP 1.5), wireless audio playback (A2DP), and remote music control (AVRCP 1.3).

Question 8

Does the JVC LT-24FD120 television have Bluetooth?

Accepted Answer

No, this JVC LT-24FD120 television does not have Bluetooth.

According to the technical specifications in the manual, the available ports on this device are:

2 HDMI ports
1 USB port
1 VGA port
1 RF port (antenna)
1 Mini AV port (composite video)
1 coaxial connector (audio output)
1 3.5 mm headphone jack
1 PC Audio jack

The model does not have Bluetooth or built-in WiFi. If you want to connect a wireless device (speaker, headphones, phone...), you can:

Use the 3.5 mm headphone jack for wired headphones or earphones
Connect an external WiFi decoder (IPTV box, Android TV Box) to one of the HDMI ports to access internet services and more connectivity

Question 9

What are the 2 ohm impedance specifications for the KD-R462?

Accepted Answer

The KD-R462 has a maximum output power of 50 W × 2 when a 4 Ω subwoofer is connected. However, the recommended impedance for this model is 4 Ω to 8 Ω.

Although the manual indicates a specification at 2 ohms, it is not recommended to use an impedance lower than 4 ohms for this device. Operating below this minimum impedance can cause an overload of the amplifier and damage both the receiver and your speakers.

For your safety and that of your equipment, ensure that your speakers or subwoofer comply with the recommended impedance of 4 Ω - 8 Ω.

Question 10

What output voltage can the JVC KD-R462 deliver?

Accepted Answer

The JVC KD-R462 sends a pre-amplified output voltage (pre-out/line) of 2,500 mV (2.5 volts) maximum on a 10 kΩ load. This voltage is constant and does not vary with the volume setting of the player - it is the standard line level, used to connect external amplifiers or audio signal processors.

The output impedance of the preamplifier is ≤ 600 Ω, ensuring clean transmission to your external equipment.

If you are looking for audible power (speaker output), the JVC KD-R462 delivers 50 W × 4 channels (or 50 W × 2 + 50 W × 1 for subwoofer) at 4 Ω on its built-in amplifier outputs.

User manual JVC : user manuals and guides in PDF

Models JVC most viewed

Browse manuals JVC by appliance type

Recent questions about devices JVC