Question 1

Why does my MCCULLOCH MCC1840B chainsaw experience jerks or irregular acceleration?

Accepted Answer

The jerks or irregular acceleration of your MCCULLOCH MCC1840B chainsaw are generally caused by fuel supply issues, engine maintenance, or carburetor adjustment. Here are the diagnostic and correction steps, in order of priority:

1. Check the fuel mixture
The 2-stroke engine requires a mixture of unleaded gasoline and 2T oil at a ratio of 40:1. Always prepare fresh fuel: a mixture older than 90 days degrades and causes jerks. Use 3.2 oz of McCulloch oil for 1 US gallon of gasoline (or 125 ml for 5 liters). If you use another brand of 2T oil, strictly adhere to the 40:1 ratio.

2. Clean or replace the air filter
A clogged filter restricts air intake and causes irregularities. Inspect the filter before each use. If it is very dirty, replace it. Never clean the filter with water or a liquid product, as this would damage it.

3. Check the spark plug
A dirty, blackened, or worn spark plug causes irregular acceleration. Check the electrode gap: it should be exactly 0.025 inch (0.635 mm). Clean the spark plug or replace it if it is too worn. Use a resistive spark plug (reference: 9295-310801).

4. Replace the fuel filter
A clogged fuel filter reduces fuel flow and creates jerks. The manufacturer recommends replacing the filter every 20 hours of use. Completely empty the tank before changing the filter: hang the old filter with a hook-shaped wire, gently pull it out, then install the new one ensuring it goes all the way to the bottom of the tank.

5. Clean the spark arrestor screen
A clogged screen dramatically reduces engine performance. Remove the two nuts from the muffler, then replace the screen with a new one.

6. Adjust the carburetor at idle
If the jerks persist after the above steps, the problem lies with the carburetor adjustment. After allowing the engine to warm up (at least 10 seconds), use a Phillips screwdriver to turn the idle screw (accessible at the air filter height) a quarter to half a turn to the right. The engine should then run smoothly. If the chain runs at idle, turn the screw to the left until the chain stops, then let the engine idle. For optimal adjustment, consult an authorized McCulloch service center.

Tip: Irregular accelerations during the first few minutes after starting (before the engine is warm) are normal. If they persist during cutting or after full warming, apply the above steps in order. Regular maintenance keeps your chainsaw in good working condition.

Question 2

How to change the cutting disc on the MCCULLOCH B43 BT brushcutter?

Accepted Answer

To change the cutting disc on your MCCULLOCH B43 BT brushcutter, follow the steps below safely:

Steps to change the cutting disc

Safety: Ensure that the machine is turned off and disconnected from any power source. If your model is battery-operated, remove the battery before starting.
Loosening the screw: Use an appropriate wrench to loosen the screw that holds the disc in place. Turn the screw counterclockwise (to the left) to unscrew it.
Removing the disc: Carefully remove the old disc from the chuck.
Installing the new disc: Place the new disc on the chuck, ensuring it is properly aligned and positioned correctly.
Securing: Re-tighten the screw by turning it clockwise (to the right) and tighten it firmly to hold the disc in place.
Checking: Ensure that the disc is securely fixed and has no play before restarting the machine.

Following these steps ensures a safe and effective disc change, prolonging the life of your MCCULLOCH B43 BT brushcutter.

Question 3

What type of fuel should be used for the McCulloch M53-190 ER lawn mower?

Accepted Answer

The McCulloch M53-190 ER lawn mower is equipped with a 4-stroke gasoline engine. To ensure optimal operation and longevity of your mower, it is recommended to use:

Unleaded gasoline with an appropriate octane rating (generally 95 or higher).
Fresh, high-quality fuel to avoid starting issues and clogging.

Avoid using gasoline containing more than 10% ethanol, as this can damage the engine. Additionally, do not add oil to the fuel, as the 4-stroke engine has a separate lubrication system.

By following these recommendations, you will ensure optimal performance and a prolonged lifespan for your McCulloch M53-190 ER mower.

Question 4

Why won't my MCCULLOCH B428 PS trimmer start and how can I resolve this issue?

Accepted Answer

If your MCCULLOCH B428 PS trimmer won't start, several common causes may be behind this problem. Here are the steps to check to try to resolve it:

1. Fuel Check

Make sure the tank contains fresh and suitable fuel (usually a 2-stroke gasoline mix if applicable).
If the fuel is old, empty the tank and refill it with new fuel.

2. Spark Plug Inspection

Remove the spark plug and inspect it for any signs of dirt or damage.
Clean the plug with a wire brush or replace it if it is worn or defective.
Ensure that the spark plug wire is properly connected.

3. Air Filter Inspection

A dirty or clogged air filter can prevent the engine from starting.
Clean the air filter according to the manufacturer's recommendations or replace it if it is too dirty.

4. Starter System Check

If your model is equipped with a pull starter, ensure that the cord is not stuck and operates correctly.
Check that all safety levers and controls are in the correct position for starting.

5. Other Tips

Ensure that the trimmer is on a stable surface and that starting conditions are optimal (e.g., cold engine).
If the problem persists after these checks, it may be necessary to consult a professional for a more in-depth diagnosis.

Question 5

How to start the MCCULLOCH VIRGINIA MH 542 lawn mower?

Accepted Answer

To start your MCCULLOCH VIRGINIA MH 542 lawn mower, follow these simple steps:

1. Preparation

Place the mower on a flat and clear surface.
Check that the fuel tank is filled.
Check the oil level to ensure optimal operation.

2. Checking the controls

Insert the ignition key if your model is equipped with one.
Make sure the safety lever is in the run position.

3. Using the choke

If the engine is cold, activate the choke to facilitate starting.

4. Starting the engine

Pull firmly and quickly on the starter cord without jamming it.
If the engine does not start after several attempts, wait a moment before trying again.

5. After starting

Deactivate the choke once the engine is running for normal operation.
Adjust the mower speed according to your needs.

By following these steps, your MCCULLOCH VIRGINIA MH 542 mower should start easily and be ready for use.

Question 6

How to fold and store the frame of the MC CULLOCH M53-190 ER lawn mower?

Accepted Answer

To fold and store the frame of your MC CULLOCH M53-190 ER lawn mower, proceed methodically and safely. The frame of this model is specially designed to be foldable to facilitate storing the machine in a limited space.

Preparation before folding

First, ensure that the mower is completely turned off and that the engine has cooled down. Wait at least a few minutes after stopping the engine for the thermal parts to no longer be hot. For added safety, you can disconnect the spark plug wire to prevent any accidental starting during folding.

Folding procedure for the frame

Locate the buttons (wing nuts) on each side of the frame, where it connects to the main structure of the mower.
Gradually and completely loosen these buttons by turning them counterclockwise. Do not remove them completely; just keep them loose enough to allow movement of the frame.
Slowly and steadily lower the frame towards the front of the machine, towards the cutting deck. The frame should fold gradually downwards.
Once the frame is in the folded position (horizontal or slightly raised towards the front), tighten the buttons firmly again to maintain this position and prevent the frame from accidentally unfolding during transport or storage.

Secure storage

After folding the frame, store the mower in a dry, well-ventilated place, protected from moisture, bad weather, and temperature fluctuations. This environment preserves the durability of the engine and mechanical parts. Ensure that the mower is stable and immobile, ideally on a flat and even surface. If you store the machine for a long time (more than 30 days), empty the fuel tank to avoid gasoline degradation and starting issues during the next use.

User manual MCCULLOCH : user manuals and guides in PDF

Models MCCULLOCH most viewed

Browse manuals MCCULLOCH by appliance type

Recent questions about devices MCCULLOCH