Q: The power cable is not provided separately and I see terminals at the back. How does the electrical connection work?

This is completely normal. The HOTPOINT-ARISTON KIC 640 Z IT cooker comes with a pre-wired power cable for a single-phase 220-240V connection at 50Hz, which is the standard configuration in Europe. The small panel with terminals that you find at the back is intended for special non-standard installations, including: 400V three-phase (configuration 2+N, simple N, or 2+2N) 220-240V three-phase Important: If your electrical network is standard single-phase (220-240V), the cable is already correctly configured and you should not touch the terminals . A multi-pole disconnect switch (minimum gap 3mm) must be placed between the appliance and your electrical network. If you are in a three-phase configuration or have any doubts about your network type, consult a qualified technician. The replacement or modification of the power cable should only be carried out by an authorized technical service , otherwise you risk voiding the warranty.

Q: Why does the flame go out when I release the gas knob?

Your HOTPOINT-ARISTON PC 640 T cooker is equipped with a flame safety device (thermocouple) that operates on a specific principle: Normal operation When lighting, you must press and hold the knob down for at least 2 to 3 seconds . This duration allows the thermocouple to heat up and activate the safety system. Once the thermocouple is activated, the flame stays lit even after releasing the knob. If the flame goes out after releasing If your flame goes out immediately after releasing, check: Holding duration: make sure to hold the knob down for at least 2 to 3 consecutive seconds. If you release too quickly, the thermocouple won't have time to heat up. Blocked orifices: the gas outlet orifices located in front of the safety device may be blocked. Clean them gently with a needle if necessary. Resetting in case of accidental extinguishing If the flame goes out accidentally, turn the knob immediately to the off position and wait at least 1 minute before attempting to relight . This pause allows the gas to escape properly and the system to reset.

Q: Where does the ventilation of the KIC 644 DD Z plate take place?

The ventilation of the KIC 644 DD Z plate occurs through a fan grille located at the front and on the sides of the appliance. This air intake is intended for the cooling of internal electronic components , and not for smoke extraction (a separate extractor hood is still necessary for that). Important points for ventilation: Ensure that the fan grille is never blocked - obstruction compromises cooling Maintain a minimum clearance of 40 mm at the back of the plate from the wall Leave a minimum space of 20 mm at the bottom between the edge of the cutout and the lower cabinet Avoid installing this plate directly above a refrigerator or washing machine (insufficient air circulation) The cooling fan activates automatically when necessary, especially at maximum power or when the boost function is activated, and may continue to operate after turning off if the internal temperature remains high.

Question 1

The power cable is not provided separately and I see terminals at the back. How does the electrical connection work?

Accepted Answer

This is completely normal. The HOTPOINT-ARISTON KIC 640 Z IT cooker comes with a pre-wired power cable for a single-phase 220-240V connection at 50Hz, which is the standard configuration in Europe.

The small panel with terminals that you find at the back is intended for special non-standard installations, including:

400V three-phase (configuration 2+N, simple N, or 2+2N)
220-240V three-phase

Important: If your electrical network is standard single-phase (220-240V), the cable is already correctly configured and you should not touch the terminals. A multi-pole disconnect switch (minimum gap 3mm) must be placed between the appliance and your electrical network.

If you are in a three-phase configuration or have any doubts about your network type, consult a qualified technician. The replacement or modification of the power cable should only be carried out by an authorized technical service, otherwise you risk voiding the warranty.

Question 2

Why does the flame go out when I release the gas knob?

Accepted Answer

Your HOTPOINT-ARISTON PC 640 T cooker is equipped with a flame safety device (thermocouple) that operates on a specific principle:

Normal operation

When lighting, you must press and hold the knob down for at least 2 to 3 seconds. This duration allows the thermocouple to heat up and activate the safety system. Once the thermocouple is activated, the flame stays lit even after releasing the knob.

If the flame goes out after releasing

If your flame goes out immediately after releasing, check:

Holding duration: make sure to hold the knob down for at least 2 to 3 consecutive seconds. If you release too quickly, the thermocouple won't have time to heat up.
Blocked orifices: the gas outlet orifices located in front of the safety device may be blocked. Clean them gently with a needle if necessary.

Resetting in case of accidental extinguishing

If the flame goes out accidentally, turn the knob immediately to the off position and wait at least 1 minute before attempting to relight. This pause allows the gas to escape properly and the system to reset.

Question 3

Where does the ventilation of the KIC 644 DD Z plate take place?

Accepted Answer

The ventilation of the KIC 644 DD Z plate occurs through a fan grille located at the front and on the sides of the appliance. This air intake is intended for the cooling of internal electronic components, and not for smoke extraction (a separate extractor hood is still necessary for that).

Important points for ventilation:

Ensure that the fan grille is never blocked - obstruction compromises cooling
Maintain a minimum clearance of 40 mm at the back of the plate from the wall
Leave a minimum space of 20 mm at the bottom between the edge of the cutout and the lower cabinet
Avoid installing this plate directly above a refrigerator or washing machine (insufficient air circulation)

The cooling fan activates automatically when necessary, especially at maximum power or when the boost function is activated, and may continue to operate after turning off if the internal temperature remains high.

User manual HOTPOINT-ARISTON Cooker : user manuals and guides in PDF

Models HOTPOINT-ARISTON Cooker most viewed

Other categories HOTPOINT-ARISTON

Recent questions about Cooker HOTPOINT-ARISTON