Q: What is the energy class of the Atag WO6211AC hood?

The Atag WO6211AC extractor hood is rated A+ according to European energy regulations. It therefore offers very good energy efficiency. Here are the main energy characteristics: Energy class: A+ Annual consumption: approximately 40 kWh/year (under standard usage) Motor power: 250 W LED lighting: 2 x 2 W The A+ classification means that this hood is among the most energy-efficient appliances in its category. This energy efficiency helps reduce your electricity consumption while maintaining effective air extraction (maximum flow rate of 600 m³/h) and an acceptable noise level (maximum 55 dB).

Question 1

What is the energy class of the Atag WO6211AC hood?

Accepted Answer

The Atag WO6211AC extractor hood is rated A+ according to European energy regulations. It therefore offers very good energy efficiency.

Here are the main energy characteristics:

Energy class: A+
Annual consumption: approximately 40 kWh/year (under standard usage)
Motor power: 250 W
LED lighting: 2 x 2 W

The A+ classification means that this hood is among the most energy-efficient appliances in its category. This energy efficiency helps reduce your electricity consumption while maintaining effective air extraction (maximum flow rate of 600 m³/h) and an acceptable noise level (maximum 55 dB).

Question 2

Where to buy a replacement Atag WG411J5U extractor hood in the UK?

Accepted Answer

To buy a replacement Atag WG411J5U extractor hood in the UK, you can explore several options:

Online retailers: Websites like Amazon, eBay, or Currys PC World often offer extractor hoods and may have this model in stock or available for order.
Specialty stores: Local appliance stores or kitchen showrooms may sell the Atag brand or be able to order this model for you.
Official Atag website: Check the official Atag UK website or contact their customer service for a list of authorized retailers or online purchasing options.
DIY stores: Large chains like B&Q or Wickes may offer extractor hoods or assist you in ordering this specific model.

By using these sources, you should be able to find an Atag WG411J5U extractor hood that meets your needs in the UK.

Question 3

How to replace an ATAG WG411J5U 100 cm island kitchen hood?

Accepted Answer

To replace an ATAG WG411J5U 100 cm island kitchen hood, follow these key steps:

1. Turn off the power supply

Before any intervention, make sure to turn off the power supply at the circuit breaker to avoid any risk of electrocution.

2. Remove the old hood

Remove the grease filters and charcoal filters if present.
Detach the hood from its ceiling mounting brackets by unscrewing the screws.
Disconnect the extraction duct or air recycling elements depending on the type of installation.
Carefully lower the hood.

3. Prepare the installation of the new hood

Check that the mounting brackets are in good condition and securely fixed to the ceiling.
Install new brackets if necessary, following the specific instructions for the ATAG WG411J5U model.

4. Install the new hood

Lift the new hood and attach it to the brackets.
Reconnect the extraction duct or install the charcoal filters for air recycling.
Ensure that all connections are tight and secure.

5. Restore the power supply and test

Turn on the circuit breaker to power the hood.
Turn on the hood and check its proper operation as well as the absence of abnormal noises.

By following these steps, you will be able to replace your ATAG WG411J5U hood safely and effectively.

Question 4

Where can I find the installation plan for the Atag WO60211BM extractor hood?

Accepted Answer

The complete installation plan for the Atag WO60211BM extractor hood can be found in the user manual provided with the product. You will find detailed diagrams and installation dimensions in the Installation section of the document.

Main dimensions:

Width: 600 mm
Height: 132 mm
Depth: 510 mm
Exhaust diameter: 125 mm
Minimum distance hood-cooking plate: 550 mm (650 mm required for gas hobs)

Available installation types: This built-in hood can be mounted either under a kitchen cabinet (recommended method) or against the wall in a free-standing installation. For each configuration, you will find in the manual the precise locations of the 4 fixing holes, the hole for the power cable, and the exhaust hole to mark before drilling.

If you have lost the paper manual, visit the official Atag website (www.atag.nl or www.atag.be) where you can download the complete manual in PDF, or contact Atag customer service who can send you the documentation or specific diagrams for the WO60211BM model.

For a correct and safe installation, it is important to respect the minimum distances, particularly the minimum height of 550 mm between the hood and your cooking plate, and to check for the absence of electrical or plumbing lines before drilling the fixing holes.

Question 5

Can the Atag WO60211BM hood be connected with a rear exhaust outlet?

Accepted Answer

Yes, the Atag WO60211BM extractor hood can indeed be connected with a rear exhaust outlet. This is one of the two standard configurations offered for this model (the other being recirculation). The cooking air sucked in is directly expelled outside through an exhaust pipe located at the back of the hood.

Diameter and exhaust duct: The rear exhaust opening of your hood has a diameter of 125 mm. It is important to use an exhaust pipe of the same diameter (125 mm) to ensure optimal performance. A duct with a smaller diameter would reduce suction capacity and increase noise.

Duct path: Ensure that the exhaust duct is as direct as possible. Each bend introduces resistance that decreases performance. Stretch the pipe as much as possible during installation and limit the number of bends. Before drilling, make sure there are no existing installation pipes.

Non-return valve: It is mandatory to install a shut-off valve or a non-return valve in the exhaust pipe to prevent cold air from coming back through the hood when it is not in use. This also improves the sealing of your installation.

Fresh air supply: If you are using the hood and a heat source (such as a gas stove) simultaneously, ensure that there is a sufficient supply of fresh air in the kitchen. The maximum allowed depression is 4 Pa to avoid problems with draft or unwanted air intake.

By following these recommendations, your rear installation will operate efficiently and quietly. The WO60211BM hood is designed for this configuration and offers a suction rate of 320 m³/h in maximum extraction mode.

User manual Atag Range hood : user manuals and guides in PDF

Models Atag Range hood most viewed

Other categories Atag

Recent questions about Range hood Atag