Q: How to effectively clean an Ariston Thermo HB 9 IX stainless steel hood?

Before cleaning , turn off the hood and unplug it. The hood should be regularly cleaned inside and out. Failure to follow cleaning rules poses fire risks. For general cleaning of your Ariston Thermo HB 9 IX hood, use a damp cloth soaked in denatured alcohol or neutral liquid detergents. Absolutely avoid abrasive products that could damage the stainless steel finish. Then wipe with a dry cloth to avoid streaks. Grease filter : this filter should be cleaned once a month. To remove it, pull on the spring release handle located under the filter. Clean it in the dishwasher at low temperatures with a quick cycle, or in soapy hot water. Once clean and dry, put it back in place by clicking it in. Then press button 1 on the control panel for about 3 seconds to reset the filter saturation indicator. Charcoal filter : this filter can be cleaned every two months. First, remove the filter support frame by unscrewing the screw (g) that secures it to the hood. Remove any excess water, taking care not to damage the filter. Then, remove the pad located inside the plastic frame and place it in the oven for 10 minutes at 100°C to dry it completely. Replace the pad and reattach the frame. After cleaning, press button 1 for about 3 seconds to reset the saturation indicator. Replace the pad every 3 years or as soon as it is damaged. By following these regular cleaning instructions, you will keep your hood in good working condition and ensure better suction efficiency.

Question 1

What should I do if my Ariston HB 9 IX hood is no longer extracting?

Accepted Answer

If your Ariston HB 9 IX hood is no longer extracting, several causes may be behind this problem. Here are the steps to follow to identify and resolve this malfunction:

1. Check the power supply

Make sure the hood is properly plugged in and that the power supply is working.
Check that the circuit breaker has not tripped or that the fuse is not blown.

2. Check the hood settings

Ensure that the hood is turned on and that the extraction mode is activated via the control panel or buttons.

3. Clean or replace the filters

A clogged grease filter can significantly reduce extraction efficiency.
Remove the filter and clean it thoroughly with soapy hot water or in the dishwasher if compatible.
If the filter is too worn or damaged, replace it with a new filter suitable for the HB 9 IX model.

4. Check the exhaust duct

If your hood is equipped with an exhaust duct, ensure it is not blocked by debris or bird nests.
Also, check the proper functioning of the backdraft damper that prevents outside air from returning to the hood.

5. Inspect the motor and internal components

If the motor is running but extraction is weak or nonexistent, there may be a mechanical or electrical issue.
In this case, it is recommended to contact a qualified professional for a safe diagnosis and repair.

6. Check the air vents

Ensure that the air vents are not blocked by dust, objects, or insects.

By following these steps, you can often resolve the extraction problem of your Ariston HB 9 IX hood. If the problem persists, a specialized technician can help you diagnose and repair the hood.

Question 2

How to effectively clean an Ariston Thermo HB 9 IX stainless steel hood?

Accepted Answer

Before cleaning, turn off the hood and unplug it. The hood should be regularly cleaned inside and out. Failure to follow cleaning rules poses fire risks.

For general cleaning of your Ariston Thermo HB 9 IX hood, use a damp cloth soaked in denatured alcohol or neutral liquid detergents. Absolutely avoid abrasive products that could damage the stainless steel finish. Then wipe with a dry cloth to avoid streaks.

Grease filter: this filter should be cleaned once a month. To remove it, pull on the spring release handle located under the filter. Clean it in the dishwasher at low temperatures with a quick cycle, or in soapy hot water. Once clean and dry, put it back in place by clicking it in. Then press button 1 on the control panel for about 3 seconds to reset the filter saturation indicator.

Charcoal filter: this filter can be cleaned every two months. First, remove the filter support frame by unscrewing the screw (g) that secures it to the hood. Remove any excess water, taking care not to damage the filter. Then, remove the pad located inside the plastic frame and place it in the oven for 10 minutes at 100°C to dry it completely. Replace the pad and reattach the frame. After cleaning, press button 1 for about 3 seconds to reset the saturation indicator. Replace the pad every 3 years or as soon as it is damaged.

By following these regular cleaning instructions, you will keep your hood in good working condition and ensure better suction efficiency.

User manual Ariston Thermo Range hood : user manuals and guides in PDF

Models Ariston Thermo Range hood most viewed

Other categories Ariston Thermo

Recent questions about Range hood Ariston Thermo