W344 - Projector OPTOMA - Free user manual and instructions
Find the device manual for free W344 OPTOMA in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product type | DLP projector |
| Native resolution | WXGA (1280 x 800) |
| Brightness | 3200 ANSI lumens |
| Contrast ratio | 20,000:1 |
| Lamp life | Up to 6000 hours (eco mode) |
| Weight | 2.5 kg |
| Dimensions (W x D x H) | 296 x 228 x 83 mm |
| Power supply | 100-240 V, 50/60 Hz |
| Power consumption | 225 W (standard mode), < 0.5 W standby |
| Keystone correction | Vertical ±40° and horizontal ±30° (manual) |
| Built-in speaker | 2 W |
| Video inputs | HDMI 1.4a, VGA, composite, S-Video |
| Audio output | 3.5 mm headphone jack |
| Quiet operation | 28 dB (eco mode) |
| Cleaning | Clean the air filter every 100 hours |
| Lamp replacement | Replacement model: OPTOMA lamp SP.85G01.001 |
| Security | Password lock, auto power off |
| Warranty | 2 years (parts and labor) |
Frequently Asked Questions - W344 OPTOMA
How do I connect my computer to the OPTOMA W344 projector?
Use a VGA or HDMI cable depending on your computer. Plug one end into the projector, the other into the computer, then select the corresponding source (VGA or HDMI) via the Source menu or remote control.
What should I do if the image is blurry?
Turn the focus ring around the lens until the image is sharp. Also check the recommended projection distance.
How do I clean the air filter?
Turn off the projector and unplug it. Open the filter cover (located on the side), remove the filter and vacuum the dust with a soft brush attachment. Replace the filter and cover. Perform this operation every 100 hours of use.
The projector lamp does not turn on, what should I do?
Check that the power cord is properly plugged in and the projector is on (green indicator). If the indicator flashes red, the lamp may be at the end of its life or the lamp cover is not closed properly. Consult the manual to replace the lamp.
How do I adjust keystone correction?
Use the Keystone buttons on the remote control or control panel to correct vertical and horizontal distortion. Adjustments range from ±40° vertical and ±30° horizontal.
Can I use the projector without the remote control?
Yes, the basic buttons are available on the projector's control panel: power on/off, source, menu, keystone correction, and focus.
How do I replace the lamp on the OPTOMA W344?
Turn off the projector, unplug it, and let it cool down. Remove the lamp cover using a screwdriver, unclip the old lamp, insert the new one (model SP.85G01.001), and close the cover. Reset the lamp timer in the menu.
The projector displays 'No signal', what should I do?
Check that the cable is properly connected to the source (computer, DVD player, etc.). Make sure the source is turned on and the projector is set to the correct input (HDMI, VGA, etc.). Try another cable if necessary.
What is the minimum projection distance?
For a 60-inch image, place the projector about 1.5 meters from the screen. Use the optical zoom to adjust size. Refer to the distance table in the manual.
How do I reset to factory settings?
Go to the Setup menu via the remote control, select 'Reset' or 'Factory Reset', then confirm. All settings will return to default values.
User questions about W344 OPTOMA
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Projector in PDF format for free! Find your manual W344 - OPTOMA and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. W344 by OPTOMA.