CH2100E - Battery charger EGO - Free user manual and instructions

Brand	EGO
Model	CH2100E
Product type	Battery charger
Input voltage	220-240 V~, 50 Hz
Input power	210 W
Output voltage	56 V --- (DC)
Output current	3 A
Compatible battery type	EGO lithium-ion: BA1120E, BA2240E, BA2800, BA3360, BA4200
Charging time (BA1120E)	Approximately 40 minutes
Charging time (BA2240E)	Approximately 80 minutes
Charging time (BA2800)	Approximately 100 minutes
Charging time (BA3360)	Approximately 115 minutes
Charging time (BA4200)	Approximately 145 minutes
Optimal charging temperature	0 °C – 40 °C
Weight	1.2 kg
Protection class	Double insulation (Class II)
LED indicators	Red and green for charge status
Use	Indoor only
Wall mounting	Yes, two holes spaced 76 mm
Maintenance	Clean with a dry cloth, do not use solvent
Safety	Overheating and faulty battery protection
Environmental compliance	WEEE and battery directives (2012/19/EU, 2006/66/EC)

Frequently Asked Questions - CH2100E EGO

What types of batteries can I charge with the EGO CH2100E charger?

This charger is designed for EGO lithium-ion batteries, models BA1120E, BA2240E, BA2800, BA3360 and BA4200. Do not charge other types of batteries.

How do I know when my battery is fully charged?

When the battery is fully charged, the charger's green LED stays on continuously and the red LED turns off. The battery's power indicator also turns off.

What to do if the red LED flashes?

A flashing red LED indicates a faulty battery or charger. Remove and reinsert the battery. If the problem persists, try with another battery. If still faulty, the charger may be defective.

Can I use the charger outdoors?

No, the charger is designed for indoor use only. Do not expose it to rain or moisture.

How to clean the charger?

Unplug the charger and clean it with a dry cloth. Never use solvents or chemicals, as they could damage the plastic parts.

What to do if the battery does not charge?

Check that the battery is correctly inserted. Ensure the battery temperature is between 3 °C and 57 °C. If the red LED is continuously on, wait for the battery to cool down or warm up. If the problem persists, refer to the troubleshooting table.

Does the charger heat up normally?

Yes, it is normal for the charger to heat up during charging. Charge in a well-ventilated area. Do not cover the charger.

How to install the charger on the wall?

Use the two mounting holes on the back of the charger, spaced 76 mm apart. Attach suitable screws to the wall that can support the weight of the charger and battery (max 3.3 kg).

Can I leave the battery on the charger after charging?

Yes, the battery will not be overcharged. However, if it remains for more than a month, the charger performs automatic maintenance and reduces the charge to 30%. It will then need to be recharged.

How to dispose of the charger or battery?

Do not dispose of electrical equipment or batteries with household waste. In accordance with the European directive, take them to a separate collection point.

USER MANUAL CH2100E EGO

Line drawing of a portable electronic device with ventilation grilles and control panel (no text or symbols)

OPERATOR'S MANUAL

56 VOLT

CHARGER

MODEL NUMBER CH2100E

EN 56 Volt charger 3

DE 56v ladegerat 8

FR Chargeur 56v 14

Technical line drawing of a mechanical device with internal components and a directional arrow (no text or symbols)

READ ALL INSTRUCTIONS!

READ OPERATOR'S MANUAL

Residual risk! People with electronic devices, such as pacemakers, should consult their physician(s) before using this product. Operation of electrical equipment in close proximity to a heart pacemaker could cause interference or failure of the pacemaker.

WARNING: To ensure safety and reliability, all repairs should be performed by a qualified service technician.

WARNING: This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

SAFETY SYMBOLS

The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols and the explanations with them deserve your careful attention and understanding. The symbol warnings do not, by themselves, eliminate any danger. The instructions and warnings they give are no substitutes for proper accident prevention measures.

WARNING: Be sure to read and understand all safety instructions in this Operator's Manual, including all safety alert symbols such as "DANGER," "WARNING," and "CAUTION" before using this tool. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury.

SAFETY INSTRUCTIONS

This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before attempting to assemble and operate.

	Safety Alert	Precautions that involve your safety.
	Read Operator's Manual	To reduce the risk of injury, user must read operator's manual
	Indoor Use Use this device indoors only
	Class II Construction	Double-insulated construction
T3,15A	Fuse-links Time-lag miniature fuse-link
V Volt	Voltage
A Amperes Current
Hz Hertz		Frequency (cycles per second)
W Watt Power
min Minutes Time
~	Alternating Current	Type of current
---	Direct Current	Type or a characteristic of current

WARNING: Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury.

WORK AREA SAFETY

- Keep the work area clean and well lit. Cluttered or dark areas invite accidents.

- Do not operate the EGO charger in explosive environments, such as in the presence of flammable liquids, gases, or dust. A charger might create a spark, which may ignite the dust or fumes.

ELECTRICAL SAFETY

■ Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with grounded power tools. Unmodified plugs and matching outlets will reduce the risk of electric shock.

- Do not expose to the charger to rain or wet conditions. Water entering the charger will increase the risk of electric shock.

EN

- Do not abuse the cord. Never use the cord for carrying, pulling, or unplugging the charger. Keep the cord away from heat, oil, sharp edges, or moving parts. Damaged or entangled cords increase the risk of electric shock.

• Avoid body contact with grounded surfaces, such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is grounded.
• When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
  ■ The EGO charger can charge the EGO lithium-ion battery packs listed below:

CHARGER BATTERY PACKS
CH2100E	BA1120E, BA2240E, BA2800,BA3360, BA4200

SERVICE

■ Have your charger serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the charger is maintained.
- When servicing a charger, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance instructions may create a risk of shock or injury.

SAFETY RULES FOR CHARGER

CAUTION: To reduce the risk of electric shock or damage to the charger and battery, charge only those lithium-ion rechargeable batteries specifically designated on your charger's label. Other types of batteries may burst, causing personal injury or damage.

■ This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

■ Before using the battery charger, read all instructions and cautionary markings in this manual and on the battery charger, the battery and the product using the battery to prevent misuse of the products and possible injury or damage.

• Do not use the charger outdoors or expose it to wet or damp conditions. Water entering the charger will increase the risk of electric shock.
• Do not handle charger, including the charger plug and charger terminals with wet hands.

■ Use of an attachment not recommended or sold by the battery-charger manufacturer may result in a risk of fire, electric shock, or injury to persons.
■ Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.

- Do not abuse the cord or charger. Never use the cord to carry the charger. Do not pull the charger cord to disconnect the plug from a receptacle. Damage to the cord or charger could occur and create an electric shock hazard. Replace damaged cords immediately.

■ Make sure that the cord is located so that it will not be stepped on, tripped over, come in contact with sharp edges or moving parts, or otherwise be subjected to damage or stress. This will reduce the risk of accidental falls, which could cause injury and damage to the cord, which could then result in electric shock.
- Keep the cord and charger away from heat to prevent damage to housing or internal parts.
- Do not allow gasoline, oils, petroleum-based products, etc. to come in contact with plastic parts. These materials contain chemicals that can damage, weaken, or destroy plastic.
- Do not operate the charger with a damaged cord or plug, which could cause shorting and electric shock. If damaged, have the charger repaired or replaced by an authorized service technician at an EGO Service Center.
- Do not operate the charger if it has received a sharp blow, been dropped, or has otherwise been damaged in any way. Take it to an authorized service technician for an electrical check to determine if the charger is in good working order.

- Do not disassemble the charger. Take it to an authorized service technician when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire.

■ Unplug the charger from the electrical outlet before attempting any maintenance or cleaning to reduce the risk of electric shock.
- Disconnect charger from the power supply when not in use. This will reduce the risk of electric shock or damage to the charger if metal items should fall into the opening. It will also help prevent damage to the charger during a power surge.

- Risk of electric shock. Do not touch the uninsulated portion of output connector or uninsulated battery terminal.

■ Save these instructions. Refer to them frequently and use them to instruct others who may use this tool. If you lend this tool to someone else, also lend these instructions to them to prevent misuse of the product and possible injury.

IMPORTANT SAFETY INSTRUCTIONS

■ Save these instructions. This manual contains important safety and operating instructions for EGO 56V Charger CH2100E.

■ Before using the battery charger, read all instructions and cautionary markings on the battery charger, the battery and the product using the battery.

WARNING: When using electric appliances, basic precautions should always be followed, including the following.

■ To reduce the risk of injury, close supervision is necessary when an appliance is used near children.
■ Only use attachments recommended or sold by manufacturer.
■ Do not use outdoors.
■ For a portable appliance – To reduce the risk of electrical shock, do not put charger in water or other liquid. Do not place or store appliance where it can fall or be pulled into a tub or sink.

CAUTION: To reduce the risk of injury, charge only lithium-ion rechargeable batteries. Other types of batteries may burst, causing personal injury or damage.

SPECIFICATIONS

Charger Input 220-240V~50Hz 210W
Charger Output	3A 56V---
Charging Time	Approximately 40 minutes for BA1120E battery pack.Approximately 80 minutes for BA2240E battery pack.Approximately 100 minutes for BA2800 battery pack.Approximately 115 minutes for BA3360 battery pack.Approximately 145 minutes for BA4200 battery pack.
Optimum Charging Temperature	0°C-40°C
Charger Weight 1.2 kg

DESCRIPTION

KNOW YOUR CHARGER (Fig. A)

1. Cooling Air Port
2. Mounting Slot
3. Electrical Contacts
4. LED Indicators
5. Wall Mounting Holes

OPERATION

HOW TO CHARGE THE BATTERY PACK

WARNING: Do not use the charger outdoors or expose it to wet or damp conditions. Water entering the charger will increase the risk of electric shock.

NOTICE: Lithium-Ion battery packs are shipped partially charged. Before using it the first time, fully charge the battery pack.

1. Connect the charger to the power supply (220-240V\~50Hz).
2. Align the raised ribs of the battery pack with the mounting slots in the charger; slide the battery pack down onto the charger as Fig. B shown.
3. The charger will communicate with the battery pack to evaluate the condition of the battery pack.
4. When the battery pack is charging, the green LED on the charger will flash. The power indicator on the battery pack will flash in sequence: red, orange and green. The fan in the charger continuously works to cool the battery pack.
5. When the battery pack is fully charged, the green LED will stop flashing and will shine green continuously. The power indicator on the battery pack will go out. Wait until the cooling fan stops, remove the battery pack from the charger and disconnect the charger from the power supply.
6. The battery pack will fully charge if left on the charger, but it will not overcharge. If the battery pack remains on the charger for one month or more, it will perform self-maintenance and drop to 30% charge capacity. If this occurs, reinstall the battery pack on the charger to recharge it fully.

NOTICE:

■ A significantly reduced run time after fully charging the battery pack indicates that the batteries are near the end of their usable life and must be replaced.
■ The charger may warm during charging. This is part of the normal operation of the charger. Charge in a well-ventilated area.

EN

LED FUNCTIONS OF CHARGER

LED Indicator	Battery Pack	Red LED on the Charger	Green LED on the Charger	Power Indicator on the Battery Pack	ACTION
[7648] CHARGING	Charging Off Flashing			Flashing red, orange and green alternatively	Charging
DEFECTIVE BATTERY	Defective Flashing Off Off				Battery pack or charger is defective.
HIGH TEMP	Cold/Hot Battery	On Off Off			Charging will begin when battery pack returns to 3°C-57°C.
[5TBW] FULL CHARGE	Fully charged	Off On Off			Charging is complete. Main-tenance charging.
---	Self-maintenance	Off	Intermittently quick flashing	Off	Battery pack is performing self-maintenance or in sleep mode. Reinstall the battery pack on the charger to recharge it fully.

CHARGING A HOT OR COLD BATTERY PACK

If the battery pack is out of the normal temperature range, the red LED will shine and the green LED will go off. When the battery pack cools down to approximately 57^ C or warms to more than 3^ C, the charger will automatically begin charging.

DEFECTIVE BATTERY PACK OR CHARGER

If the charger detects a problem, the red LED will begin flashing and the green LED will go off.

1. If registering as defective, remove and reinsert the battery pack in the charger. If the LEDs still read "defective" a second time, try charging a different battery pack.
2. If a different battery pack charges normally, dispose of the defective battery pack (refer to the instructions in the battery pack manual).
3. If a different battery pack also indicates "defective", unplug the charger and wait until the red LED goes out, then reconnect the plug to the power supply. If the red LED on charger still display defective, the charge may be defective.

WALL-MOUNT HOLES

The charger has hanging holes for convenient storage (Fig. A-5). Install screws in the wall 76mm apart. Use screws sufficiently strong to hold the combined weight of the charger and battery pack (approximately maximum 3.3kg).

MAINTENANCE

WARNING: To avoid serious personal injury, always remove the battery pack from the tool when cleaning or performing any maintenance.
WARNING: When servicing, use only identical EGO replacement parts. Use of any other parts may create a hazard or cause product damage.
WARNING: It is not recommended to use compressed dry air as a cleaning method of the charger. If cleaning with compressed air is the only method to apply, always wear safety goggles or safety glasses with side shields when cleaning the tool. If the operation is dusty, also wear a dust mask.

WARNING: If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.

WARNING: Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc. come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury.

WARNING: When servicing, use only identical EGO replacement parts. Use of any other parts may create a hazard or cause product damage. To ensure safety and reliability, all repairs should be performed by a qualified service technician at an EGO Service Center.

Protecting the environment

Do not dispose of electrical equipment, battery charger and batteries/rechargeable batteries into household waste!

According to the European law 2012/19/EU, electrical and electronic equipment that is no longer usable, and according to the European law 2006/66/EC, defective or used battery packs/batteries, must be collected separately.

If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being.

TROUBLESHOOTING

PROBLEM CAUSE SOLUTION
Charger doesn’t work. The red LED flashes red or all the LEDs go out.	Battery pack or charger is defective or bad connection between the battery pack and charger.	■ Try to remove and reinsert the battery pa in the charger.■ Try charging a different battery pack.■ Unplug the charger and wait until the red LED goes out, then reconnect the plug to the power supply.
Charger doesn’t work and red LED shines red.	Battery pack is too hot or too cold.	Allow the battery pack to reach normal temperature. Charging will begin when battery pack returns to 3°C-57°C.
The charger produces a rhythmic sound and the power indicator on the battery pack is OFF.	The battery pack is over-discharged.	Leave the battery on the charger and check in 30 minutes to see if the power indicator on the battery pack turns on. If yes, the battery pack is activated successfully. If no, the battery pack may be damaged.

WARRANTY

EGO WARRANTY POLICY

Please visit the website egopowerplus.com for full terms and conditions of the EGO Warranty policy.

KEN UW LADER (afb. 1)

SIKKERHET I ARBEIDSOMRÅDET

GENERELT VEDLIKEHOLD

BEZPIECZEŃSTWO W MIEJSCU PRACY

POLITYKA GWARANCYJNA EGO

SEZNAMTE SE S VAŠÍ NABÍJEČKOU (obr. A)

DÔLEŽITÉ BEZPEČNOSTNÉ POKYNY

CITIȚI MANUALUL DE INSTRUCTIUNI

ÎNCĂRCAREA UNUI SET DE ACUMULATORI CALD SAU RECE

LUGEGE KASUTUSJUHENDIT

OLULISED OHUTUSJUHISED

LAADIJA LEDIDE FUNKTSIONAALSUS