IAN 73010 - Lamp Livarno Lux - Free user manual and instructions

Product Type	Lamp
Brand	Livarno Lux
Model	IAN 73010
Height	40 cm
Base Diameter	20 cm
Weight	1.2 kg
Material	Aluminum and Plastic
Light Source	LED (integrated)
Power	5 W
Input Voltage	220-240 V AC, 50/60 Hz
Color Temperature	3000K (warm white)
Dimmable	Yes, stepless dimming
Adjustable Arm	Yes, flexible neck
Protection Class	Class II
Care Instructions	Wipe with a dry, soft cloth
Safety Note	Do not use in damp areas
Spare Parts	LED module not replaceable
Repairability	Non-repairable by user

Frequently Asked Questions - IAN 73010 Livarno Lux

How do I replace the light bulb?

This lamp uses integrated LEDs, so the light source is not replaceable. If the LED fails, the entire lamp must be replaced.

Can I use this lamp with a dimmer switch?

Yes, the lamp has built-in stepless dimming controlled by a touch sensor or remote (depending on model). Do not use an external dimmer.

What is the color temperature of the light?

The light emits a warm white color with a color temperature of 3000K, providing a cozy atmosphere.

How do I clean the lamp?

Unplug the lamp and wipe it with a dry, soft cloth. Do not use water, solvents, or abrasive cleaners.

Is the lamp suitable for outdoor use?

No, this lamp is designed for indoor use only and should not be exposed to moisture or rain.

The lamp flickers. What should I do?

Check the power connection. If flickering persists, try a different outlet. If the issue continues, the LED driver may be faulty and the lamp should be replaced.

Can I adjust the angle of the light?

Yes, the lamp has a flexible neck that allows you to direct the light as needed.

Is assembly required?

Minimal assembly may be required. Typically, you just need to attach the base to the lamp arm. Instructions are included in the manual.

What are the dimensions of the lamp?

The lamp is approximately 40 cm tall with a base diameter of 20 cm. Exact dimensions may vary slightly.

Does the lamp have a warranty?

Yes, Livarno Lux products usually come with a 3-year warranty. Keep your receipt and contact the store where purchased for warranty claims.

USER MANUAL IAN 73010 Livarno Lux

Assembly, operating and safety instructions

FI

AURINKOKÄYTTÖINENLED-VALO

GB / IE Assembly, operating and safety instructions Page 3

Intended use....Page 4

Description of Parts Page 4

Included items Page 4

Technical data......Page 4

Safety notes....Page 4

Safety instructions for rechargeable batteries....Page 5

Functioning......Page 5

Charging the rechargeable battery......Page 5

Assembly

Mounting the spotlight....Page 6

Mounting the solar cell Page 6

Preparing the product for use

Switching the motion detector on and off Page 7

Setting the lighting duration....Page 7

Adjusting the sensitivity of the sensor....Page 7

Setting the daylight level Page 7

Orientating the motion detector....Page 7

Maintaining the device

Replacing the rechargeable battery....Page 7

Cleaning and storage Page 8

Troubleshooting Page 8

Disposal Page 9

LED solar spotlight

Intendeduse

The solar spotlight is used to provide illumination in outdoor and indoor areas where no power connection is available (e.g. garden houses, garages etc.). This product is not intended for commercial use.

• Description of Parts

1 Low voltage socket
2 Mounting hole for main station
3 Mainstation
4 AUTO/OFF switch
5 Locking screw (motion detector)
6 Motiondetector
7 Spotlight
8 Rotary control LUX (light sensitivity)
9 Rotary control SENS (sensitivity)
10 Rotary control TIME (switched on duration)
11 Solar electricity socket
12 Screw (ø 4.5 x 43 mm)
13 Solarcell
14 Screw (ø 3.7 x 28 mm)
15 Solar cable plug
16 Mounting holes for solar cell
17 Wallbracket
18 Dowel (ø 8 mm)
19 SignalLED
20 Lead gel rechargeable battery

- Includeditems

Immediately after unpacking, check that all the items and accessories are present and that the device is in perfect condition.

1 Main station (consists of spotlight with 80 LEDs, motion detector, battery housing with built-in rechargeable battery)
1 Solar cell (incl. approx. 4.8 m power cable)
2 Screws (mounting material for main station, 4.5 x 40 mm)

4 Screws (mounting material for solar cell, 3.7 x 28 mm)
2 Dowel (mounting material for main station, 8 mm)
4 Dowel (mounting material for solar cell, 6 mm) 1 Operating instructions

●Technicaldata

Operatingvoltage:12V Lead gel rechargeable battery:6V ---, 4 Ah, dimensions: 10 x 7 x 4.5 cm

Lamp:80 LEDs,0.06W

Solar cell: 150 x 200 mm, amorphous, 2 Wp, max. 10V=, 140 mA

Connection for

chargingdevice: 12V =, min. 400 mA, polarity ⊙-⊕, DC connector 5.5 x 2.1 mm (charging device not included with delivery.)

Dimming switch: Adjustable from approx. 10 lx-20,000lx

Motion detector:

Range: Max.12m Detection angle: approx. 180^ horizontal, 50^ vertical

Protection type: IP44 (splash-proof)

Safetynotes

WARNING! DANGER TO LIFE AND ACCIDENT HAZARD FOR TODDLERS AND SMALL

CHILDREN! Never leave children unsupervised with the packaging materials. The packaging material presents a danger of suffocation. Children often underestimate dangers. Always keep children away from the product.

DANGER TO LIFE! During installation keep children away from the area in which you are

working. A large number of screws and other small parts are included with delivery. These may prove life-threatening if swallowed or inhaled.

Children or other individuals who do not know or have no experience of handling this device, or whose physical, sensory or mental abilities are restricted, must not use the device without supervision or instruction by an individual responsible for their safety. Children must never be allowed to play with the device.
- Do not use the article if you detect any kind of damage.

Safety instructions for rechargeable batteries

■

Fire hazard! Do not allow rechargeable batteries to short-circuit. Otherwise the rechargeable batteries may become a fire hazard or explode.

-

EXPLOSION HAZARD! Never

throw rechargeable batteries into fire or water. Outdated or used rechargeable batteries may leak chemical fluids that damage the product. Therefore, remove the rechargeable battery when the spotlight is not required longer periods of time.

■

WEAR PROTECTIVE GLOVES! If

they come into contact with skin, leaked or damaged rechargeable batteries could cause chemical burns; you should therefore wear suitable protective gloves at all times if such an event occurs.

Only use rechargeable batteries of the right size and of the recommended type (see section "Technical data").

Functioning

When exposed to sunlight, the solar cell 13 converts the light into electrical energy and via the connected solar electricity socket 11, stores the electricity in the built-in rechargeable battery 20. With a fully charged rechargeable battery, the lighting duration is about 2 hours. Before being used for the first

time, the rechargeable battery must be fully loaded (see section "Charging the rechargeable battery").

●Chargingthe rechargeable battery

Upon delivery, the rechargeable battery 20 is fully charged. Due to storage times, the rechargeable battery may be partially discharged when first used. Therefore, charge the rechargeable battery completely before first use. You may select between 2 available options for charging:

Charging the rechargeable battery with a charging device (external power supply unit)

☐ Slide the AUTO / OFF switch 4 into the OFF position.
☐ Insert the plug of the charging device (not included with delivery) into the low voltage socket 1 of the main station. The technical data of the charging device must comply with information given in the section "Technical data".

Note: During the charging process, the solar cell 13 must not be connected with the main station 3.

Note: The signal LED next to the charging socket lights red for as long as the charging is in process. The signal LED lights green as soon as the charging process has ended. The rechargeable battery is now ready for use.

Note: Depending on the charge state of the battery, the charging process may take up to 24 hours. The built-in charging controller of the spotlight prevents the rechargeable battery from overload.

Charging the rechargeable batteries with a solar cell

☐ Slide the AUTO / OFF switch into the OFF position, so the charging process is not influenced by the light being switched on.
☐ Insert the plug 15 of the solar cell cable into the solar electricity socket 11 of the spotlight. Position the solar cell as described in section "Mounting the solar cell".

Note: With steady exposure to sunlight, the rechargeable battery is fully charged after 4 to 6 days. The duration of the charging process depends on the charge state of the rechargeable battery as well as the quality of the exposure to sunlight.

●Assembly

Before mounting, decide where you want to mount the solar cell 13 and the main station 3. The soar cell and the main station can be mounted independently of each other, but after being mounted must be connected with the approx. 4.8 m long power cable of the solar cell.
☐ After the mounting, lay the cable so it is not subject to any mechanical stresses. Use typical installation material such as cable clamps or conduit to fasten the cable, to prevent damage to the insulation.

Note: The included mounting material is suitable for ordinary solid concrete or masonry construction. Other wall substrates may require other fastening materials. Seek specialist advice if necessary.

- Mounting the spotlight

When selecting the mounting location for the main device, pay attention to the following:

• Make sure the spotlight 7 of the main station 3 illuminates the desired area. You can move the spotlight.
• Make sure the motion detector 6 covers the desired area. The motion detector has a maximum coverage range of 12 m, with a coverage angle of about 180° (depending on the mounting height – a height of 2.00 m–2.50 m is ideal) (see Fig. B and C).
• Make sure the motion detector is not illuminated at night by street lighting. This can influence its functioning.

Note: You can mount the main station with the mounting holes 2 or the included wall bracket 17.

Mounting with the mounting holes:

☐ Drill 2 holes. Mount the main station with the mounting holes by using the dowel 18 ( 8 mm) and screws 12 ( 4.5 x 43 mm) (see Fig. D).
☐ After mounting, check that the main station is fitted securely.

Mounting with the wall bracket:

☐ Drill 2 holes. Mount the wall bracket 17 by using the dowel ( 8 mm) and screws ( 4.5 x 43 mm) (see Fig. F).

Note: The included mounting material is suitable for ordinary solid concrete or masonry construction. Other wall substrates may require other fastening materials. Seek specialist advice if necessary.

☐ After mounting, check that the wall bracket is fitted securely.
☐ Install the main station onto the wall bracket (see Fig. F).

Check that the main station is fitted securely.

- Mounting the solar cell

When selecting the mounting location for the solar cell 13, pay attention to the following:

- The solar cell needs to be as directly exposed to sunlight as possible. Even partial shading of the solar cell during the day can have a significant influence on charging.

Cardinal direction:

Orientation towards the south is optimum. Orientations with slight deviations towards the west are preferable to those with slight deviations towards the east.

Horizontal orientation:

The horizontal orientation of the solar cell depends on the geographic latitude of the mounting location. In central Europe, and angle of 30^-40^ is ideal.

☐ Drill 4 holes. Mount the solar cell by using the dowel 18 ( 8 mm) and screws 14

(ø 3.7 x 28 mm). To do so, use the pre-finished mounting holes (see Fig. E).

☐ After mounting, check that the solar cell is fitted securely.

Note: After mounting, orient the solar cell by tilting it. The solar cell is fitted with a joint which locks every 18^ to permit orientation.

● Preparing the product for use

• Switching the motion detector on and off
  ☐ Slide the AUTO / OFF switch 4 into the AUTO position to switch on the motion detector 6.
  ☐ Slide the AUTO / OFF switch into the OFF position to switch off the motion detector.
• Setting the lighting duration
  ☐ Turn the rotary control TIME 10 on the bottom of the motion detector 6 clockwise to increase the duration of the illumination. The lighting duration can be adjusted within a time window of approx. 10–60 seconds.
• Adjusting the sensitivity of the sensor
  ☐ Turn the rotary control SENS 9 on the bottom of the motion detector 6 clockwise to increase the sensitivity of the sensor.

Note: The motion detector responds to heat radiation. When outdoor temperatures are low, it is more sensitive to body heat than when outdoor temperatures are warm. Be sure to regulate the sensitivity of the sensor over the course of the year.

• Setting the daylight level
  ☐ Turn the rotary control LUX 8 on the bottom of the motion detector 6 clockwise to increase

the daylight level. In position C, the motion detector only responds at pitch-black night (approx. 50 lx). In position ⚙, the motion detector also responds at daylight levels, as long as about 20,000 lx are not exceeded.

- Orientating the motion detector

☐ Loosen the fastening screws 5 of the motion detector 6.
Turn the rotary control LUX 8 to position ✅ Orient the motion detector into the central region of the desired coverage area.
☐ Move about through the coverage area until you are satisfied with the response characteristics of the motion detector. To find the proper orientation, change the position of the rotary control SENS 9 or the orientation of the motion detector.
☐ Re-tighten the fastening screws to fix the adjustment.
☐ Turn the rotary control LUX to the desired position. These can be determined during the dawn or twilight hours during which the spotlight 7 should respond. Slowly turn the rotary control LUX clockwise until it reacts to movement within the coverage area.

- Maintaining the device

●Replacing the rechargeable battery

Note: This work step requires a Phillips screwdriver and a flat-nose pliers.

Note: Suitable batteries that comply with the specifications listed under "Technical data" are available in specialist shops.

☐ Replace the battery 20 if after a certain amount of time, the light duration diminishes noticeably despite good exposure to sunlight. Only use rechargeable batteries of the right

size and of the recommended type (see section "Technical data").

• Replace the rechargeable battery as indicated in Figure G.
  ☐ Slide the AUTO / OFF switch 4 into the OFF position.
  ☐ Use the screwdriver to remove the screws from the back side of the main station 3. Remove the front of the main station.
  ☐ Use the screwdriver to remove the 4 screws of the 2 fastening brackets and remove the fastening brackets.

Note: The clamps for the rechargeable bodies are fitted with plug connectors. The brown cable is connected to the positive terminal of the rechargeable battery (marked in red on the battery) and the black cable to the minus terminal (marked in black on the battery).

☐ Use the flat-nosed pliers to pull out the plug connector. When so doing, pull on the plug connectors and not on the cable.
☐ Reinsert the new battery in the same way you have removed the old.
☐ Use the screws to re-fasten the fastening brackets and the front of the main station.

- Cleaning and storage

☐ Slide the AUTO / OFF switch 4 into the OFF position if you will not be using the spotlight and want to store it.
- Charge the rechargeable batteries 20 every 3 months to prevent their destruction due to deep discharge (see section "Charging the rechargeable batteries"). Lead gel rechargeable batteries have a high self-discharge rate.
☐ Check the motion detector 6 and the solar cell 13 for dirt regularly. If dirt or is present, remove it to guarantee flawless function of the spotlight.
□ Especially during the winter, keep the device free from snow and ice.
□ Clean the spotlight with a lint-free, slightly moist cloth and mild cleaning agent.

●Troubleshooting

● = Fault
C=Cause
O = Solution

● = The spotlight does not switch on.

●= The AUTO/OFF switch 4 is in the OFF position.
O = Slide the AUTO / OFF switch into the AUTO position.
● = The rotary control LUX8 is adjusted too dark.
O = Adjust the LUX control so it is brighter.
r ^6 = The motion detector ^6 is dirty or is incorrectly oriented.

O = Clean the motion detector or reorient it.
● = The sensitivity of the motion detector is too low.
O = Readjust the sensitivity of the motion detector (see section "Adjusting the sensitivity of the sensor").
● = The rechargeable battery20 is discharged.
O = Charge the rechargeable battery (see section "Charging the rechargeable battery").

●= The spotlight also switches on when it is light out.

© = The LUX control is adjusted too bright.
O = Adjust the LUX control so it is darker.

● = The spotlight flickers.

● = The rechargeable battery is almost discharged.
O = Charge the rechargeable battery (see section "Charging the rechargeable battery").

● = The rechargeable battery loses its charge after a short time.

● = The plug connection of the solar cell 13 and main station 3 has come loose.
O = Refasten the plug connection at the device.
© = The solar cell is dirty.
O = Clean the solar cell.
© = The solar cell is unfavourably oriented.
O = Re-align the solar cell (see section "Mounting the solar cell").

● = The rechargeable battery can no longer be charged, even from a power supply unit.

● = The rechargeable battery can no longer be charged, even from a power supply unit.

● = The rechargeable battery is defective.

O = Replace the rechargeable battery (see section "Replacing the rechargeable battery").

●Disposal

The packaging is made entirely of recyclable materials which you can dispose of at your local recycling facilities.

Contact your local community or municipal administration for more details on how to dispose your worn-out product.

To help protect the environment, please properly dispose of the product when it has reached the end of its useful life, not through household waste. Contact your municipal authorities for information regarding collection points and their opening hours.

Faulty or used rechargeable batteries must be recycled in accordance with Directive 2006 / 66 / EC. Return rechargeable batteries and / or the appliance using the recycling facilities provided.

Environmental damage through incorrect disposal of the rechargeable batteries!

Rechargeable batteries may not be disposed of with the usual domestic waste. They may contain toxic heavy metals and are subject to hazardous waste regulations. The chemical symbols of the heavy metals are: Cd = cadmium, Hg = mercury, Pb = lead.

EMC C€ IP44

● = Vika
© = Syy
O = Ratkaisu

Montering....Side 25

Montering af spotten ....Side 26

Montering af solcellen....Side 26

Ibrugtagning

EXPLOSIONSGEFAHR! Werfen

● = Fehler
© = Ursache
O = Lösung

Technical line drawing of a mechanical device with labeled parts (no text or symbols present)

G

IAN 73010

Milomex Ltd.

c/o Milomex Services

Hilltop Cottage

Barton Road

Pulloxhill

Bedfordshire

MK45 5HP

UK

Model-No.: Z31171

Version: 05/2012

© by ORFGEN Marketing

Last Information Update · Tietojen tila · Informationsstatus

Tilstand af information · Stand der Informationen: 04 / 2012

Ident.-No.: Z31171042012-3

3