JSM1017 - Jigsaw Ferm - Free user manual and instructions

Product type	Pendulum jigsaw
Brand	Ferm
Model	JSM1017
Power	570 W
No-load speed	500 - 3 000 min⁻¹
Max. cutting depth (wood)	70 mm
Miter angle	0° to 45°
Number of pendulum positions	4
Cutting stroke	18 mm
Weight	2.0 kg
Mains voltage	230 V ~
Mains frequency	50 Hz
Double insulation	Yes
Dust extraction	Vacuum cleaner connection
Parallel guide	Included, up to 16 cm
Speed adjustment	6-position dial
Blade holder	Tool-less (Allen screw)
Suitable materials	Wood, metal, plastic, ceramic, rubber
Sound pressure level	90.4 dB(A)
Sound power level	101.4 dB(A)
Vibration (wood)	7.7 m/s²
Vibration (metal)	13.0 m/s²

Frequently Asked Questions - JSM1017 Ferm

How to change the saw blade?

To change the blade, lift the protective guard (5), loosen the Allen screws (14) with the Allen key (12), remove the old blade and insert the new one making sure the teeth point upward and forward. Tighten the screws and lower the guard.

How to adjust the speed?

Use the speed adjustment dial (3) to select one of the 6 positions. For hard materials, use a slow speed; for soft materials, a fast speed. Do not adjust the speed during use.

How to adjust the miter angle?

Loosen the Allen screws (18) under the base plate, tilt the base plate to the desired angle (0° to 45°, readable on the scale), then tighten the screws. Do not adjust the angle during use.

What is the pendulum motion and how to adjust it?

The pendulum motion changes the tooth attack. Turn the switch (4) to position 0 (steel, ceramic), 1 (plastics, aluminum), 1-3 (wood). Do not adjust during use.

Can I use a vacuum cleaner with this saw?

Yes, insert the dust extraction adapter (19) into the connection (10) and connect a vacuum cleaner hose for efficient dust removal.

How to maintain the jigsaw?

Always unplug before cleaning. Clean the housing with a soft cloth, the ventilation slots with a damp cloth. Regularly lubricate the guide roller and replace worn blades.

What are the important safety precautions?

Wear safety glasses, hearing protection and a dust mask. Hold the machine by the insulated surfaces to avoid electric shock. Check the condition of the blade before use and do not work on materials containing asbestos.

What materials can I cut with this saw?

Wood, metal, plastic, ceramic and rubber. Choose the appropriate blade: coarse for wood, fine for steel and aluminum, extra fine for curves in wood.

How to use the parallel guide?

Loosen the Allen screws (8), insert the parallel guide (17) into the base plate (7), set the desired distance (max. 16 cm) and tighten the screws. It allows precise parallel cuts.

What to do in case of excessive vibration?

If the machine vibrates strongly at idle, immediately turn it off and unplug it. Check that the blade is correctly mounted and in good condition. Vibrations may indicate a dull or poorly installed blade.

USER MANUAL JSM1017 Ferm

Thank you for buying this Ferm product.

By doing so you now have an excellent product, delivered by one of Europe's leading suppliers. All products delivered to you by Ferm are manufactured according to the highest standards of performance and safety. As part of our philosophy we also provide an excellent customer service, backed by our comprehensive warranty. We hope you will enjoy using this product for many years to come.

SAFETY WARNINGS

WARNING

Read the enclosed safety warnings, the additional safety warnings and the instructions.

Failure to follow the safety warnings and the instructions may result in electric shock, fire and/or serious injury.

Keep the safety warnings and the instructions for future reference.

The following symbols are used in the user manual or on the product:

Read the user manual.

Risk of personal injury.

Risk of electric shock.

Immediately remove the mains plug from the mains if the mains cable becomes damaged and during cleaning and maintenance.

Wear safety goggles.

Wear hearing protection.

Wear a dust mask.

Double insulated.

Do not dispose of the product in unsuitable containers.

The product is in accordance with the applicable safety standards in the European directives.

Additional safety warnings for jigsaws

• Do not work materials containing asbestos. Asbestos is considered carcinogenic.
• Wear safety goggles, hearing protection and if necessary other protective means, such as safety gloves, safety shoes, etc.
• Before use, remove all nails and other metal objects from the workpiece.
• Make sure that the workpiece is properly supported or fixed.
• Do not use the machine without the guard.
• Inspect the saw blade before each use. Do not use saw blades which are bent, cracked, or otherwise damaged.
• Make sure that the saw blade is properly mounted.
• Only use saw blades that are suitable for use with the machine.
• Only use saw blades with the correct dimensions.
• Do not use other accessories than saw blades.
• Do not use saw blades made of HSS steel.
• Do not use the machine on workpieces requiring a maximum sawing depth that exceeds the maximum sawing depth of the saw blade.
• Hold the machine by the insulated gripping surfaces where the saw blade may contact hidden wiring or the mains cable. If the saw blade contacts a 'live' wire, the exposed metal parts of the machine can also become 'live'. Risk of electric shock.
• Let the machine run at no load in a safe area after mounting the saw blade. If the machine vibrates strongly, immediately switch off the machine, remove the mains plug from the mains, and try to solve the problem.
• Beware that the saw blade continues to rotate for a short period after switching off the machine. Do not attempt to bring the saw blade to a standstill yourself.

Kickback

Kickback is the upward and backward movement of the saw blade when the saw blade unexpectedly touches an object. Securely hold the machine during use. Keep your attention focused on the operation.

Kickback is usually caused by:

• unintentionally touching hard objects or materials with the rotating saw blade;
• a blunt saw blade;
• a saw blade that is not properly mounted;
• sawing into a previous cut;
• a lack of attention to the operation;
• an instable stance.

Electrical safety

Always check that the voltage of the power supply corresponds to the voltage on the rating plate.

• Do not use the machine if the mains cable or the mains plug is damaged.
• Only use extension cables that are suitable for the power rating of the machine with a minimum thickness of 1.5 mm^2 . If you use an extension cable reel, always fully unroll the cable.

Mains plug replacement (UK only)

If the moulded 3-pin plug attached to the unit is damaged and needs replacing, it is important that it is correctly destroyed and replaced by an approved BS 1363/5A fused plug and that the following wiring instructions are followed.

The wires in the mains cable are coloured in accordance with the following code:

blue neutral

brown live

As the colours of the wires in the mains cable of the unit may not correspond to the coloured markings identifying the terminals in the plug, proceed as follows:

• The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
• The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

TECHNICAL DATA

JSM1017

Mains voltage V\~ 230

Mains frequency Hz 50

Power input W 570

No-load speed min ^-1 500 - 3,000

Max. sawing depth (wood) mm 70

Max. sawing stroke mm 18

Mitre angle ° 45

Number of pendulum positions 4

Weight kg 2.0

NOISE AND VIBRATION

JSM1017
Sound pressure ( L_pa )	dB(A) 90.4
Acoustic power ( L_wa )	dB(A) 101.4
Uncertainty (K)	dB(A) 3
Vibration (wood)	m/s ^2 7.7
Vibration (metal)	m/s ^2 13.0
Uncertainty (K) m/s	^2 1.5

Wear hearing protection.

Vibration level

The vibration emission level stated in this instruction manual has been measured in accordance with a standardised test given in EN 60745; it may be used to compare one tool with another and as a preliminary assessment of exposure to vibration when using the tool for the applications mentioned

• using the tool for different applications, or with different or poorly maintained accessories, may significantly increase the exposure level
• the times when the tool is switched off or when it is running but not actually doing the job, may significantly reduce the exposure level

Protect yourself against the effects of vibration by maintaining the tool and its accessories, keeping your hands warm, and organizing your work patterns

DESCRIPTION (FIG. A)

Your pendulum action jigsaw has been designed for sawing wood, metal, plastics, ceramics, rubber, etc. to any required size and in any required shape.

1. On/off switch
2. Lock-on button
3. Speed adjustment wheel
4. Pendulum action switch
5. Guard
6. Saw blade holder
7. Saw shoe
8. Allen screw for parallel guide
9. Scale for mitre angle
10. Dust extraction connection
11. Grip
12. Allen key
13. Allen key holder

ASSEMBLY

Before assembly, always switch off the machine and remove the mains plug from the mains.

Mounting and removing the saw blade (fig. B)

Refer to the table below to select the required saw blade.

Saw blade Material

Coarse Wood

Medium Wood

Fine Steel, aluminium, plastic

Very fine Wood (curves)

Do not attempt to remove the guard from the machine.

Mounting

• Raise the guard (5).
• Slacken the Allen screws (14) using the Allen key (12).
• Insert the saw blade (15) in the saw blade holder (6) as far as possible. The teeth of the saw blade (15) must point upward and forward. The smooth side of the saw blade must engage in the slot of the guide roller (16).
• Tighten the Allen screws (14) using the Allen key (12).
• Lower the guard (5).

Removing

• Raise the guard (5).
• Slacken the Allen screws (14) using the Allen key (12).
• Remove the saw blade (15) from the saw blade holder (6).
• Tighten the Allen screws (14) using the Allen key (12).
• Lower the guard (5).

Mounting and removing the parallel guide (fig. C)

The parallel guide is used for sawing along edges at a maximum distance of 16 cm.

Mounting

• Slacken the Allen screws (8) using the Allen key (12).
• Insert the parallel guide (17) into the saw shoe (7).
• Set the parallel guide (17) to the required position.

- Tighten the Allen screws (8) using the Allen key (12).

Removing

• Slacken the Allen screws (8) using the Allen key (12).
• Remove the parallel guide (17) from the saw shoe (7).
• Tighten the Allen screws (8) using the Allen key (12).

USE

Switching on and off (fig. A)

• To switch on the machine, press the on/off switch (1).
• To switch the machine to continuous mode, keep the on/off switch (1) pressed and simultaneously press the lock-on button (2).
• To switch off continuous mode, press the on/off switch (1) again.
• To switch off the machine, release the on/off switch (1).

Setting the speed (fig. A)

The speed adjustment wheel is used for setting the speed. The speed adjustment wheel can be set to 6 positions. The ideal speed depends on the profile and the teeth of the saw blade and on the material to be worked.

Do not set the speed during use.

• Turn the speed adjustment wheel (3) to the required position.
• For hard materials, use a saw blade with fine teeth and select a lower speed.
• For soft materials, use a saw blade with coarse teeth and select a higher speed.

Setting the mitre angle (fig. D)

The mitre angle is variable between 0^ and 45^ . The mitre angle can be read from the scale (9).

Do not set the mitre angle during use.

• Slacken the Allen screws (18) using the Allen key (12).
• Tilt the saw shoe (7) to the required position.
• Tighten the Allen screws (18) using the Allen key (12).

Using the pendulum action switch (fig. A)

The pendulum action switch is used to set the way in which the teeth of the saw blade grip the material. The pendulum action switch can be set to 4 positions.

Do not set the pendulum position during use.

- Turn the pendulum action switch (4) to required position according to the material to be worked. Refer to the table below to select the required position.

Material Pendulum position

Wood 1-3

Plastics 1

Aluminium 0-1

Steel 0

Ceramics 0

Rubber 0

Dust extraction (fig. E)

• Insert the dust extraction adapter (19) into the dust extraction connection (10).
• Connect the hose of a vacuum cleaner to the dust extraction adapter (19).

Hints for optimum use

• Clamp the workpiece. Use a clamping device for small workpieces.
• Draw a line to define the direction in which to guide the saw blade.
• Firmly hold the machine by the grip.
• Set the sawing speed.
• Set the mitre angle.
• Set the pendulum position.
• Switch on the machine.
• Wait until the machine has reached full speed.
• Place the saw shoe on the workpiece.
• Slowly move the machine along the pre-drawn line, firmly pressing the saw shoe against the workpiece.
• Do not apply too much pressure on the machine. Let the machine do the work.
• Switch off the machine and wait for the machine to come to a complete standstill before putting the machine down.

CLEANING AND MAINTENANCE

Before cleaning and maintenance, always switch off the machine and remove the mains plug from the mains.

• Regularly clean the housing with a soft cloth.
• Keep the ventilation slots free from dust and dirt. If necessary, use a soft, moist cloth to remove dust and dirt from the ventilation slots.
• Regularly clean the saw blade to avoid inaccuracies during use.
• Regularly lubricate the guide roller.

Replacing the saw blade (fig. B)

Worn or damaged saw blades must be replaced immediately.

Only use sharp and undamaged saw blades.

• To remove the old saw blade (15), proceed as described in the section „Mounting and removing the saw blade“.
• To mount the new saw blade (15), proceed as described in the section „Mounting and removing the saw blade“.

WARRANTY

Consult the enclosed warranty terms.

ENVIRONMENT

Disposal

The product, the accessories, and the packaging must be sorted for environmentally friendly recycling.

Only for EC countries

Do not dispose of power tools into domestic waste. According to the European Guideline 2002/96/EC for Waste Electrical and Electronic Equipment and its implementation into national right, power tools that are no longer usable must be collected separately and disposed of in an environmentally friendly way.

The product and the user manual are subject to change. Specifications can be changed without further notice.

PENDELHUBSTICHSÄGE JSM1017

BESCHRIJVING (FIG. A)

PŘÍMOČARÁ PILA JSM1017

KYVADLOVÁ LUPIENKOVÁ PÍLA JSM1017

TECHNINIAI DUOMENYS
JSM1017

Fin Oțel, aluminiu, material plastic

Foarte fin Lemn (curbe)

Lemn 1-3

Material plastic 1

Aluminiu 0-1

Oțel 0

Ceramică 0

Cauciuc 0

DECLARATION OF CONFORMITY

(GB) We declare under our sole responsibility that this product is in conformity and accordance with the following standards and regulations:
(DE) Der Hersteller erklärt eigenverantwortlich, dass dieses Produkt den folgenden Standards und Vorschriften entspricht:
(NL) Wij verklaren onder onze volledige verantwoordelijk heid dat dit product voldoet aan, en in overeenstem ming is met, de volgende standaarden en reguleringen:
(FR) Nous déclarons sous notre seule responsabilité que ce produit est conforme aux standards et directives suivants:
(ES) Declaramos bajo nuestra exclusiva responsabilidad que este producto cumple con las siguientes normas y estándares de funcionamiento:
(PT) Declaramos por nossa total responsabilida-de que este produto está em conformidade e cumpre as normas e regulamentações que se seguem:
(IT) Dichiariamo, sotto la nostra responsabilità, che questo prodotto è conforme alle normative e ai regolamenti seguenti:
(SV) Vi garanterar på eget ansvar att denna produkt upp fyller och följer följande standarder och bestämmelser:
(FI) Vakuutamme yksinomaan omalla vastuullamme, että tämä tuote täyttää seuraavat standardit ja säädökset:
(NO) Vi erklærer under vårt eget ansvar at dette produktet er i samsvar med følgende standarder og regler:
(DA) Vi erklærer under eget ansvar, at dette produkt er i overensstemmelse med følgende standarder og bestemmelser:
(HU) Felelősségünk teljes tudatában kijelentjük, hogy ez a termék teljes mértékben megfelel az alábbi szabványoknak és előírásoknak:
(CS) Na naši vlastní zodpovědnost prohlašujeme, že je tento výrobek v souladu s následujícími standardy a normami:

(SK) Vyhlasujeme na našu výhradnú zodpovednosť, že tento výrobok je v zhode a súlade s nasledujúcimi normami a predpismi:
(SL) S polno odgovornostjo izjavljamo, da je ta izdelek v skladu in da odgovarja naslednjim standardom terpredpisom:
(PL) Deklarujemy na własną odpowiedzialność, że ten produkt spełnia wymogi zawarte w następujących normach i przepisach:
(LT) Prisiimdami visą atsakomybę deklaruojame, kad šis gaminys atitinka žemiau paminėtus standartus arba nuostatus:
(LV) Apgalvojam ar visu atbildību, ka šis produkts ir saskaņā un atbilst sekojošiem standartiem un nolikumiem:
(ET) Deklareerime meie ainuvastutusel, et see toode on vastavuses ja kooskõlas järgmiste standardite ja määrustega:
(RO) Declarăm prin aceasta cu răspunderea deplină că produsul acesta este în conformitate cu următoarele standarde sau directive:
(HR) Izjavljujemo pod vlastitom odgovornoLsu da je strojem ukladan sa slijedešim standardima ili standardiziranim dokumentima i u skladu sa odredbama:
(SR) Pod punom odgovornošću izjavljujemo da je usaglašen sa sledećim standardima ili normama:
(RU) Под свою ответственность заявляем, что данное изделие соответствует следующим стандартам и нормам:
(UK) На свою власну відповідальність заявляемо, що дане обладнання відповідає наступним стандартам і нормативам:
(EL) Δηλώνουμε υπεύθυνα ότι προϊόν αυτό συμφωνεί και τηρεί τους παρακάτω κανονισμο ύς και πρότυπα:
(BG) Ние заявяваме, по своя собствена отговорност, че този продукт отговаря на следните стандарти и директиви

EN 55014-1, EN 55014-2, EN 60745-1, EN 60745-2-11, EN 61000-3-2, EN 61000-3-3

2006/42/EC, 2006/95/EC, 2004/108/EC, 2002/96/EC, 2002/95/EC

Zwolle, 01-01-2010

J.A. Bakker-vanlagen

CEO Ferm BV

It is our policy to continuously improve our products and we therefore reserve the right to change the product specification without prior notice.

Ferm BV • Lingenstraat 6 • 8028 PM • Zwolle The Netherlands

Spare parts list

Position	Description	No.
6+10+12+13	Guide wheel complete	407808
14	Gear	407806
20+21+22	Saw mechanism complete	407807
35	Rotor	407805
36	Carbon brush holder	407800
37+38	Carbon brush set	407801
40	Stator	407804
42	Adapter for vacuum cleaner	407809
48	Switch	407802
49	Speed control plate	407803
50	Side guide	407810