PDM1031 - Drill Ferm - Free user manual and instructions
Find the device manual for free PDM1031 Ferm in PDF.
| Product type | Hammer drill |
| Brand | Ferm |
| Model | PDM1031 |
| Mains voltage | 230 V~ |
| Mains frequency | 50 Hz |
| Power | 500 W |
| No-load speed | 0 - 3 000 min⁻¹ |
| Impact rate | 0 - 48 000 min⁻¹ |
| Max. drilling diameter (wood) | 25 mm |
| Max. drilling diameter (concrete) | 13 mm |
| Max. drilling diameter (steel) | 10 mm |
| Weight | 1.8 kg |
| Protection class | IP 20 |
| Double insulation | Yes |
| Electronic speed control | Yes |
| Direction of rotation | Forward / Reverse |
| Drilling / hammering selector | Yes |
| Chuck | Keyed |
| Auxiliary handle | Yes, adjustable |
| Depth stop | Yes |
| Switch lock | Yes |
| Sound pressure level (Lₚₐ) | 97.7 dB(A) |
| Sound power level (Lₘₐ) | 108.7 dB(A) |
| Vibration (drilling concrete) | 18.64 m/s² |
| Vibration (drilling metal) | 2.98 m/s² |
| Drillable materials | Wood, metal, plastic, brick, concrete |
| Maintenance | Clean the housing with a soft cloth, clear the ventilation slots, clean the chuck and the drill bit |
| Safety | Wear goggles, hearing protection, dust mask, gloves; do not work on asbestos; hold by insulated surfaces |
| Warranty | Check the provided terms |
| Disposal | Do not dispose of with household waste; recycle according to WEEE directive |
Frequently Asked Questions - PDM1031 Ferm
User questions about PDM1031 Ferm
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Drill in PDF format for free! Find your manual PDM1031 - Ferm and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. PDM1031 by Ferm.
USER MANUAL PDM1031 Ferm
IMPACT DRILL PDM1031
Thank you for buying this Ferm product.
By doing so you now have an excellent product, delivered by one of Europe's leading suppliers.
All products delivered to you by Ferm are manufactured according to the highest standards of performance and safety. As part of our philosophy we also provide an excellent customer service, backed by our comprehensive warranty. We hope you will enjoy using this product for many years to come.
SAFETY WARNINGS
WARNING
Read the enclosed safety warnings, the additional safety warnings and the instructions.
Failure to follow the safety warnings and the instructions may result in electric shock, fire and/or serious injury.
Keep the safety warnings and the instructions for future reference.
The following symbols are used in the user manual or on the product:
Read the user manual.
Risk of personal injury.
Risk of electric shock.
Immediately remove the mains plug from the mains if the mains cable becomes damaged and during cleaning and maintenance.
Wear safety goggles.
Wear hearing protection.
Wear a dust mask.
Wear safety gloves.
Variable electronic speed.
Double insulated.
Do not dispose of the product in unsuitable containers.
The product is in accordance with the applicable safety standards in the European directives.
Additional safety warnings for impact drills
- Do not work materials containing asbestos. Asbestos is considered carcinogenic.
- Wear safety goggles.
- Wear hearing protection to avoid the risk of hearing loss.
- If necessary, use other protective means, such as safety gloves, safety shoes, etc.
- Hold the machine with one hand on the main grip and the other hand on the auxiliary grip. Risk of personal injury.
- Hold the machine by the insulated gripping surfaces where the accessory may contact hidden wiring or the mains cable. If the accessory contacts a 'live' wire, the exposed metal parts of the machine can also become 'live'. Risk of electric shock.
- Do not use accessories which are not specifically designed and recommended by the manufacturer. Risk of personal injury.
- Only use accessories that are suitable for use with the machine.
- Only use accessories with the correct dimensions. Make sure that the accessories are properly mounted.
- Inspect the machine and the accessories before each use. Do not use accessories which are bent, cracked, or otherwise damaged. If the machine or one of the accessories is dropped, inspect the machine or the accessory for damage. If necessary, replace the accessory.
- Let the machine run at no load in a safe area after mounting the accessories. If the machine vibrates strongly, immediately switch off the machine, remove the mains plug from the mains, and try to solve the problem.
- Make sure that the maximum speed for the accessory is larger than or the same as the maximum speed of the machine. Refer to the rating plate on the machine.
- Before use, remove all nails and other metal objects from the workpiece.
- Make sure that the workpiece is properly supported or fixed.
- Keep your hands away from the workpiece during use.
- Never put the machine down on a table or a workbench before it has been switched off.
Electrical safety
Always check that the voltage of the power supply corresponds to the voltage on the rating plate.
- Do not use the machine if the mains cable or the mains plug is damaged.
- Only use extension cables that are suitable for the power rating of the machine with a minimum thickness of 1.5 mm^2 . If you use a extension cable reel, always fully unroll the cable.
Mains plug replacement (UK only)
If the moulded 3-pin plug attached to the unit is damaged and needs replacing, it is important that it is correctly destroyed and replaced by an approved BS 1363/5A fused plug and that the following wiring instructions are followed.
The wires in the mains cable are coloured in accordance with the following code:
blue neutral brown live
As the colours of the wires in the mains cable of the unit may not correspond to the coloured markings identifying the terminals in the plug, proceed as follows:
- The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
- The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
TECHNICAL DATA
| PDM1031 | |
| Mains voltage V~ 230 | |
| Mains frequency Hz 50 | |
| Power input W 500 | |
| No-load speed min | ^-1 0 - 3,000 |
| Impact rate min | ^-1 0 - 48,000 |
| Max. drill bit diameter | |
| Wood mm 25 | |
| Concrete mm 13 | |
| Steel mm 10 | |
| Protection class IP 20 | |
| Weight | kg 1.8 |
NOISE AND VIBRATION
| PDM1031 | |
| Sound pressure ( L_pa ) | dB(A) 97.7 |
| Acoustic power ( L_wa ) | dB(A) 108.7 |
| Uncertainty (K) | dB(A) 3 |
| Impact drilling mode | m/s ^2 18.64 |
| Drill into metal | m/s ^2 2.98 |
| Uncertainty (K) m/s | ^2 1.5 |
Wear hearing protection.
Vibration level
The vibration emission level stated in this instruction manual has been measured in accordance with a standardised test given in EN 60745; it may be used to compare one tool with another and as a preliminary assessment of exposure to vibration when using the tool for the applications mentioned
- using the tool for different applications, or with different or poorly maintained accessories, may significantly increase the exposure level
- the times when the tool is switched off or when it is running but not actually doing the job, may significantly reduce the exposure level
Protect yourself against the effects of vibration by maintaining the tool and its accessories, keeping your hands warm, and organizing your work patterns
DESCRIPTION (FIG. A)
Your impact drill has been designed for drilling holes in wood, metal and plastics and for hammer drilling in brick and concrete.
- On/off switch
- Lock-on button
- Speed adjustment wheel
- Forward/reverse switch
- Switch for drilling / hammer drilling
- Chuck
- Main grip
- Auxiliary grip
- Depth stop
- Chuck key
- Chuck key holder
ASSEMBLY
Before assembly, always switch off the machine and remove the mains plug
from the mains.
Mounting and removing the drill bit (fig. B)
The machine is suitable for use of the following drill bits:
- Wood (HSS)
- Metal (HSS)
- Concrete / masonry (hard metal)
Mounting
- Place the chuck key (10) into one of the holes in the chuck (6).
- Open the chuck (6) by turning the chuck key (10) counterclockwise.
- Insert the drill bit (12) into the chuck (6).
- Close the chuck (6) by turning the chuck key (10) clockwise.
- Remove the chuck key (10) from the chuck (6).
Removing
- Place the chuck key (10) into one of the holes in the chuck (6).
- Open the chuck (6) by turning the chuck key (10) counterclockwise.
- Remove the drill bit (12) from the chuck (6).
- Close the chuck (6) by turning the chuck key (10) clockwise.
- Remove the chuck key (10) from the chuck (6).
Mounting and removing the auxiliary grip (fig. C)
Mounting
- Loosen the auxiliary grip (8).
- Slide the auxiliary grip (8) over the chuck (6).
- Turn the auxiliary grip (8) to the required position.
- Tighten the auxiliary grip (8).
Removing
- Loosen the auxiliary grip (8).
- Remove the auxiliary grip (8) from the chuck (6).
- Tighten the auxiliary grip (8).
Mounting and removing the depth stop (fig. D)
The depth stop is used to set the maximum drilling depth.
Mounting
- Loosen the auxiliary grip (8).
- Insert the depth stop (9) through the hole in the auxiliary grip (8).
- Set the depth stop (9) to the required position.
- Tighten the auxiliary grip (8).
Removing
- Loosen the auxiliary grip (8).
- Remove the depth stop (9) from the auxiliary grip (8).
- Tighten the auxiliary grip (8).
USE
Switching on and off (fig. A)
- To switch on the machine, press the on/off switch (1). The further the on/off switch (1) is pressed, the higher the speed of the machine.
- To switch the machine to continuous mode, keep the on/off switch (1) pressed and simultaneously press the lock-on button (2).
- To switch off continuous mode, press the on/off switch (1) again.
- To switch off the machine, release the on/off switch (1).
Forward/reverse switch (fig. A)
Do not change the direction of rotation during use.
- For clockwise rotation, slide the forward/reverse switch (4) to the left.
- For counterclockwise rotation, slide the forward/reverse switch (4) to the right.
Setting the maximum drilling speed (fig. A)
Do not set the speed during use.
- Turn the speed adjustment wheel (3) clockwise to increase the maximum drilling speed.
- Turn the speed adjustment wheel (3) counterclockwise to decrease the maximum drilling speed.
Setting the operating mode (fig. E)
Do not change the operating mode during use.
- Set the switch (5) to position "A" for drilling.
- Set the switch (5) to position "B" for hammer drilling.
Hints for optimum use
- Clamp the workpiece.
- Firmly hold the machine with both hands.
- Place the drill bit on the workpiece.
- Switch on the machine.
- Do not apply too much pressure on the machine. Let the machine do the work.
- Switch off the machine and wait for the
machine to come to a complete standstill before putting the machine down.
CLEANING AND MAINTENANCE
Before cleaning and maintenance, always switch off the machine and remove the mains plug from the mains.
- Regularly clean the housing with a soft cloth.
- Keep the ventilation slots free from dust and dirt. If necessary, use a soft, moist cloth to remove dust and dirt from the ventilation slots.
- Regularly clean the chuck and the drill bit to avoid inaccuracies during use.
Replacing the drill bit (fig. B)
- To remove the drill bit (12), proceed as described in the section "Mounting and removing the drill bit".
- To mount the drill bit (12), proceed as described in the section "Mounting and removing the drill bit".
WARRANTY
Consult the enclosed warranty terms.
ENVIRONMENT
Disposal
The product, the accessories, and the packaging must be sorted for environmentally friendly recycling.
Only for EC countries
Do not dispose of power tools into domestic waste. According to the European Guideline 2002/96/EC for Waste Electrical and Electronic Equipment and its implementation into national right, power tools that are no longer usable must be collected separately and disposed of in an environmentally friendly way.
The product and the user manual are subject to change. Specifications can be changed without further notice.
SCHLAGBOHRMASCHINE PDM1031
BESCHRIJVING (FIG. A)
TEKNISET TIEDOT
PDM1031
TECHNINIAI DUOMENYS
PDM1031
DECLARATION OF CONFORMITY
(GB) We declare under our sole responsibility that this product is in conformity and accordance with the following standards and regulations:
(DE) Der Hersteller erklärt eigenverantwortlich, dass dieses Produkt den folgenden Standards und Vorschriften entspricht:
(NL) Wij verklaren onder onze volledige verantwoordelijk heid dat dit product voldoet aan, en in overeenstem ming is met, de volgende standaarden en reguleringen:
(FR) Nous déclarons sous notre seule responsabilité que ce produit est conforme aux standards et directives suivants:
(ES) Declaramos bajo nuestra exclusiva responsabilidad que este producto cumple con las siguientes normas y estándares de funcionamiento:
(PT) Declaramos por nossa total responsabilida-de que este produto está em conformidade e cumpre as normas e regulamentações que se seguem:
(IT) Dichiariamo, sotto la nostra responsabilità, che questo prodotto è conforme alle normative e ai regolamenti seguenti:
(SV) Vi garanterar på eget ansvar att denna produkt upp fyller och följer följande standarder och bestämmelser:
(FI) Vakuutamme yksinomaan omalla vastuullamme, että tämä tuote täyttää seuraavat standardit ja säädökset:
(NO) Vi erklærer under vårt eget ansvar at dette produktet er i samsvar med følgende standarder og regler:
(DA) Vi erklærer under eget ansvar, at dette produkt er i overensstemmelse med følgende standarder og bestemmelser:
(HU) Felelősségünk teljes tudatában kijelentjük, hogy ez a termék teljes mértékben megfelel az alábbi szabványoknak és előírásoknak:
(CS) Na naši vlastní zodpovědnost prohlašujeme, že je tento výrobek v souladu s následujícími standardy a normami:
(SK) Vyhlasujeme na našu výhradnú zodpovednosť, že tento výrobok je v zhode a súlade s nasledujúcimi normami a predpismi:
(SL) S polno odgovornostjo izjavljamo, da je ta izdelek v skladu in da odgovarja naslednjim standardom terpredpisom:
(PL) Deklarujemy na własną odpowiedzialność, że ten produkt spełnia wymogi zawarte w następujących normach i przepisach:
(LT) Prisiimdami visą atsakomybę deklaruojame, kad šis gaminys atitinka žemiau paminėtus standartus arba nuostatus:
(LV) Apgalvojam ar visu atbildību, ka šis produkts ir saskaņā un atbilst sekojošiem standartiem un nolikumiem:
(ET) Deklareerime meie ainuvastutusel, et see toode on vastavuses ja kooskõlas järgmiste standardite ja määrustega:
(RO) Declarăm prin aceasta cu răspunderea deplină că produsul acesta este în conformitate cu următoarele standarde sau directive:
(HR) Izjavljujemo pod vlastitom odgovornoLšu da je strojem ukladan sa slijedešim standardima ili standardiziranim dokumentima i u skladu sa odredbama:
(SR) Pod punom odgovornošću izjavljujemo da je usaglašen sa sledećim standardima ili normama:
(RU) Под свою ответственность заявляем, что данное изделие соответствует следующим стандартам и нормам:
(UK) На свою власну відповідальність заявляемо, що дане обладнання відповідає наступним стандартам і нормативам:
(EL) Δηλώνουμε υπεύθυνα ότι προϊόν αυτό συμφωνεί και τηρεί τους παρακάτω κανονισμο ύς και πρότυπα:
(BG) Ние заявяваме, по своя собствена отговорност, че този продукт отговаря на следните стандарти и директиви
EN 55014-1, EN 55014-2, EN 60745-1, EN 60745-2, EN 61000-3-2, EN 61000-3-3
2004/108/EC, 2006/95/EC, 2006/42/EC, 2002/96/EC, 2002/95/EC
Zwolle, 01-01-2010
J.A. Bakker-van logen
CEO Ferm BV
It is our policy to continuously improve our products and we therefore reserve the right to change the product specification without prior notice.
Ferm BV • Lingenstraat 6 • 8028 PM • Zwolle The Netherlands
Spare parts list
| Position Description No. | ||
| 1 | L | eft screw (for drill chuck) 407387 |
| 2 | D | rill chuck |
| 9 | G | ear 407382 |
| 16 Armature 409745 | ||
| 17 Carbon brush holder 407389 | ||
| 18 Carbon brush (set) 407386 | ||
| 22 Field coil 409746 | ||
| 26 + 27 Side handle | 4 | 0 |
| 31 Switch | 407384 | |
| 37 Chuck key | 407381 | |
- IMPACT DRILL PDM1031
- SAFETY WARNINGS
- WARNING
- Additional safety warnings for impact drills
- Electrical safety
- Mains plug replacement (UK only)
- Vibration level
- DESCRIPTION (FIG. A)
- ASSEMBLY
- Mounting and removing the drill bit (fig. B)
- Mounting
- Removing
- Mounting and removing the auxiliary grip (fig. C)
- Mounting and removing the depth stop (fig. D)
- USE
- Switching on and off (fig. A)
- Forward/reverse switch (fig. A)
- Setting the maximum drilling speed (fig. A)
- Setting the operating mode (fig. E)
- Hints for optimum use
- CLEANING AND MAINTENANCE
- Replacing the drill bit (fig. B)
- WARRANTY
- ENVIRONMENT
- Disposal
- Only for EC countries
- SCHLAGBOHRMASCHINE PDM1031
- BESCHRIJVING (FIG. A)
- DECLARATION OF CONFORMITY
- EN 55014-1, EN 55014-2, EN 60745-1, EN 60745-2, EN 61000-3-2, EN 61000-3-3
Brand : Ferm
Model : PDM1031
Category : Drill