LXC PHT18 - Saw Cocraft - Free user manual and instructions

Product Type	Telescopic Hedge Trimmer / Pole Saw (combo)
Model	LXC PHT18
Article Numbers	31-9460 (Hedge Trimmer), 31-9461 (Pole Saw), 31-9462 (Hedge Trimmer Head), 31-9463 (Pole Saw Head)
Weight (without battery)	3.3 kg
Telescopic Shaft Length	1.94 – 2.70 m (Pole Saw), up to 2.95 m (Hedge Trimmer)
Cutter Bar Length (Hedge Trimmer)	450 mm
Guide Bar Length (Pole Saw)	18 cm
Saw Chain Speed	5.5 m/s
Oil Tank Capacity (Pole Saw)	80 ml
Max Cutting Diameter (Hedge Trimmer)	14 mm
Power Source	18V Lithium-ion battery (LXC system, sold separately)
Sound Pressure Level (Pole Saw)	LpA = 79.5 dB(A), K = 3 dB(A)
Sound Power Level (Pole Saw)	LwA = 94 dB(A), K = 3 dB(A)
Sound Pressure Level (Hedge Trimmer)	LpA = 77.5 dB(A), K = 3 dB(A)
Sound Power Level (Hedge Trimmer)	LwA = 92.4 dB(A), K = 3 dB(A)
Vibration Level	1.79 m/s², K = 1.5 m/s²
Safety Features	Overload protection, low-voltage protection, overheating protection, safety catch for power trigger
Adjustable Head Angles	Pole Saw: 0°, 15°, 30°; Hedge Trimmer: 10 positions from -45° to 90°
Included Accessories	Shoulder strap, blade/bar guard
Maintenance	Lubricate blade/chain regularly; clean ventilation slots; store in dry place; sharpen saw chain when dull
Spare Parts and Reparability	Use only original spare parts; repairs must be performed by qualified personnel
Disposal	Do not dispose with household waste; recycle at designated collection points

Frequently Asked Questions - LXC PHT18 Cocraft

What battery does the Cocraft LXC PHT18 use?

It uses an 18V Lithium-ion battery from the LXC system (sold separately). The battery must be fully inserted until it clicks into place.

How do I adjust the length of the telescopic shaft?

Open the cam lever (5), adjust the shaft to the desired length, then close the cam lever securely.

How do I change the angle of the hedge trimmer head?

Push in the lock (12) and rotate the head to one of the ten fixed angles. Ensure the lock springs out to lock the head in place.

How do I tension the saw chain?

Loosen the drive cover lock (26), remove the cover, then turn the saw chain tension adjustment ring (25) clockwise until the chain can be pulled about 2 mm from the guide bar. Retighten the cover.

What type of oil should I use for the saw chain?

Use good quality saw chain oil. The oil tank has a capacity of 80 ml and a level window (21) for checking.

Why does my pole saw stop during use?

This could be due to overload protection (brief high load) or overheating protection (extended high load). Release the power trigger, wait, and restart after removing load. The battery may also be discharged.

What is the maximum branch diameter I can cut with the hedge trimmer?

The maximum cutting diameter for the hedge trimmer is 14 mm.

How do I store the tool when not in use?

Remove the battery, clean the tool, lubricate the blade/chain, and store in a dry dust-free place out of children's reach. Always fit the blade/bar guard.

Can I use the pole saw while standing on a ladder?

No, never work while standing on a ladder. Maintain a stable stance and use the carrying harness for balance.

How do I dispose of the product?

Do not dispose with household waste. Recycle at your local collection facility or contact the place of purchase for environmentally safe disposal.

USER MANUAL LXC PHT18 Cocraft

Blue handheld tool with black handle and wire strap, no visible text or symbols

Art.no Model

31-9460

31-9461

31-9462

31-9463

ASYPHT5450

ASYPCS7200

ASYPHT5450

ASYPCS7200

Important:

Read the entire instruction manual carefully and make sure that you fully understand it before you use the equipment. Keep the manual for future reference.

Viktig information:

Original instructions

Bruksanvisning i original

Originalbruksanvisning

Postal 10 - 13 Market Place

Kingston Upon Thames

Surrey

KT1 1JZ

DEUTSCHLAND

Kundenservice Hotline: [phone]

E-Mail: [e-mail]

Telescopic Hedge Trimmer/Pole Saw

Art.no 31-9460 Model ASYPHT5450

31-9461 ASYPCS7200

31-9462 ASYPHT5450

31-9463 ASYPCS7200

Please read the entire instruction manual before use and then save it for future reference. We reserve the right for any errors in text or images and any necessary changes made to technical data. In the event of technical problems or other queries, please contact our Customer Services (see address details on the back).

Safety

General Power Tool Safety Warnings

Warning: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.

4) Power tool use and care

a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool's operation. If damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

5) Battery tool use and care

a) Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
b) Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
c) When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
d) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.

6) Service

a) Repairs and service should only be performed by qualified persons, and only with original spare parts. This guarantees the safety of the electrical hand tool.

Additional safety rules for hedge trimmers

• This product must not be used by anyone (including children) suffering from physical or mental impairment. Persons without sufficient experience and knowledge may only use the hedge trimmer if they have received instructions in its use by someone responsible for their safety.
• Keep all bodily parts away from the cutting blades. Do not remove debris from the blades or hold onto any material that you are cutting whilst the trimmer blades are in motion. Remove the battery before dislodging any debris. One moment of carelessness can result in serious personal injury.
• Never allow children to play with the product.
• Turn off the hedge trimmer and carry it by the handle when moving it short distances. Always switch the hedge trimmer off and fit the blade guard before transporting the trimmer or moving it from one workplace to another.
• Before beginning work, make sure that there are no foreign objects such as fencing wire in the hedge/bush about to be trimmed.
  • Always hold the hedge trimmer with both hands during use.
• The blades will continue in motion for a few seconds after the power has been turned off.

Warning: Do not touch the blades while they are in motion.

Safety instructions specific to pruning saws

• Bear in mind that the product's use might be restricted by national or local regulations. Find out if any restrictions apply to your area.
• A safe working distance of at least 10 m must always be maintained between the product and any high-voltage power cables.
• Read and make sure you understand the instruction manual before using the product.
• Always make sure that you are well-balanced when using the saw. Take regular breaks when working for long periods.
• Maintain a firm stance and posture and always use the supplied carrying harness.
• Keep bystanders at a safe distance from the work area.
• Always saw branches into smaller pieces, starting at the tip and working in towards the trunk. Be aware of your position to avoid being struck by falling branches.
• Never operate the product if any of its safety devices is missing or damaged.
• Use protective eyewear and hearing protection. Further protective equipment for head, hands, legs and feet is recommended. Wearing the correct protective equipment reduces the risk of personal injury from flying debris or accidental contact with the saw chain.

Safety symbols

Read the entire instruction manual.

Do not expose the electric power tool to rain.

Safety helmet, eye protection and ear protection must be worn.

Keep all bodily parts away from the cutting mechanism (saw chain, hedge trimmer blades) during start and while using the electric power tool.

Safety gloves must be worn.

Note: Remove the battery from the electric power tool before any care or maintenance is performed.

Safety shoes must be worn.

Beware of falling objects. Keep bystanders away.

A safe distance of 10 m from the high-voltage cable must always be maintained.

Product description

31-9460 Telescopic hedge trimmer (battery and charger sold separately)
31-9461 Telescopic pole saw (battery and charger sold separately)
31-9462 Hedge trimmer head, accessory for 31-9461 (battery and charger sold separately)
31-9463 Pole saw head, accessory for 31-9460 (battery and charger sold separately)

1. Rear handle
2. Power trigger
3. Safety catch for power trigger

4. Battery connection

5. Cam lever for telescopic shaft length adjustment

6. Cam lever for hedge trimmer/pole saw head

7. Shoulder strap

8. Adjustable carry strap attachment
9. Front handle

1. Cutter bar
2. Motor housing ventilation slits
3. Lock for hedge trimmer head angle adjustment
4. Telescopic shaft mount
5. Blade guard

1. Saw chain

2. Telescopic shaft mount

3. Guide bar

4. Saw chain oil level window

5. Filler cap for saw chain oil

6. Spiked bumper

7. Motor housing ventilation slits

8. Bar guard

9. Lock for pole saw head angle adjustment

1. Drive cover
2. Saw chain tension adjustment ring
3. Drive cover lock

Overload protection and other safety features

The battery has a number of safety features that prevent damage to the hedge trimmer/pole saw and battery during use.

- During brief moments of high loads, the overload protection may switch the hedge trimmer/pole saw off. This protection resets automatically. Release the power switch, wait a few seconds, ensure that there is no load and restart the hedge trimmer/pole saw. The hedge trimmer/pole saw should now function normally again.

• Under high loads for extended periods, the overheating protection may switch the hedge trimmer/pole saw off. This feature is self-resetting but the hedge trimmer/pole saw cannot be restarted until it has returned to a safe operating temperature. Let the hedge trimmer/pole saw battery cool before trying to restart it. Adverse temperatures can occur in direct sunlight and should therefore be avoided.
• The battery has a low-voltage protection device, which operates when the battery becomes discharged. The low-voltage protection device turns off the hedge trimmer/pole saw automatically and the battery then needs to be recharged.

Hedge trimmer/pole saw head adjustment and installation

Telescopic shaft length adjustment

1. Open the cam lever.
2. Adjust the shaft to the desired length.
3. Close the cam lever.

Hedge trimmer

Attaching the hedge trimmer head to the telescopic shaft

1. Remove the protective cover from the electrical connections.

2. Open the cam lever and slide the hedge trimmer head onto the telescopic shaft.

3. Make sure that the locking tabs extend fully.

4. Close the cam lever.

Illustration of a hand holding a small electronic device with an arrow pointing to it (no text or symbols present)

Mechanical assembly diagram showing a tool interacting with a cylindrical component, with directional arrows indicating motion (no text or symbols)

Mechanical component diagram showing a lever and pin assembly with an arrow indicating direction (no text or symbols)

Hedge trimmer head angle adjustment

Push in the lock (12) and rotate the head to one of the ten fixed angles. Ensure that the lock springs out properly so that the head is locked at the desired angle.

Pole saw

Fitting the guide bar and saw chain

1. Loosen the drive cover lock (26) and remove the cover.

2. Place the saw chain in the groove in the guide bar. Fit the chain around the chain sprocket (A) and fit the guide bar over the guide pin (B).

3. Refit the drive cover. Tighten enough to move the guide bar into the right position but do not tighten the lock all the way.

4. Pull the guide bar forwards by hand to remove any slack from the chain.

5. Turn the saw chain tension adjustment ring (25) clockwise until the chain is taut. The chain is correctly tensioned when it can be pulled out 2 mm from the guide bar and then springs back.

Technical illustration of a chain-linking device with gear and chain (no text or symbols)

Warning:

A new saw chain stretches during use and should be checked and readjusted after just a few minutes use. The chain tension should be checked regularly. The chain should not be so slack that it is hanging down away from the guide bar. You should be able to lift the chain about 2 mm up from the guide bar and then it springs back.

Attaching the pole saw head to the telescopic shaft

1. Remove the protective cover from the electrical connections.
2. Open the cam lever and slide the pole saw head onto the telescopic shaft.
3. Make sure that the locking tabs extend fully.
4. Close the cam lever.

Pole saw head angle adjustment

Push in the lock (19) and rotate the head to one of the three fixed angles. Ensure that the lock springs out properly so that the head is locked at the desired angle.

Illustration of a robotic arm tool with three sequential steps showing the grip, blade, and handle (no text or symbols present)

Instructions for use

Hedge trimmer

Warning:

• Always keep the work area tidy so you can move freely without the risk of tripping over obstacles.
• Make sure that there are no loose branches, which could become caught in the hedge trimmer.
  • Make sure that you are wearing all required safety gear before starting.
  • Make sure that all parts of the hedge trimmer head are intact, in place and undamaged.
  • Make sure that the blade is sharp and lubricated.
• Keep the motor housing ventilation slots free from debris.
• The safety catch for the power switch (3) and the power switch (2) should be easily activated without sticking and otherwise function normally.
• Check that both handles are clean and easily gripped.

Start

1. Remove the blade guard.
2. Loosen the knob on the carry strap attachment (6) and adjust the attachment to the desired position.
3. Slide the battery into the battery connector (4) and make sure that it clicks securely into place.
4. Push the safety catch for the power trigger (3) forwards and pull the power trigger (2). The trimmer should now start.
5. The hedge trimmer will stop automatically if the power trigger is released.

Diagram of a mechanical device with a lever and base, showing motion direction (no text or symbols)

Sparks may sometimes appear inside the motor housing when the motor is turned off. This is completely normal.

Cutting/trimming

• Make sure that there are no hidden obstacles (metal poles/wire fences) in the area to be trimmed.
  • Max branch diam: 14 mm.
• Hold the trimmer firmly; maintain a steady stance and do not lean out too far. Be extra careful when using a ladder.
• Move the trimmer along in a slow and steady motion.
• The double-sided cutter blade enables trimming in both directions or in a pendulum action from side to side.
• For even trimming on the sides, it is better to cut in the direction of growth, from the bottom up.
• If you trim from the top down, the thinner twigs will bend out and there is a risk of holes or thin patches appearing in your hedge.
• In order to ensure a straight top edge, you can stretch a length of string over the hedge as a guide.

Pole saw

Warning:

• Always keep the work area tidy so you can move freely without the risk of tripping over obstacles.
• Make sure that there are no loose branches that could become caught in the pole saw.
• Make sure that you are wearing all required safety gear before starting.
• Make sure that all parts of the pole saw head are intact, in place and undamaged.
• Check that the saw chain is sharp and completely taut.
• Keep the motor housing ventilation slots free from debris.
• The safety catch for the power trigger (3) and the power trigger (2) should be easily activated without sticking and otherwise function normally.
• Check that both handles are clean and easily gripped.

Topping up the saw chain oil

1. Open the saw chain oil filler cap (17) and top up with good quality saw chain oil. Check the level in the window (21).
2. Screw the cap back on.
3. Check the oil level regularly while working.

Sawing technique

It is advisable to practice your sawing technique on easily accessible branches first. This will allow you to comfortably practice your sawing technique in various situations. It will then be easier and safer for you to progress onto using more advanced sawing techniques.

Warning: Never saw into bushes or thin branches. These can get caught in the saw chain and cause the saw to be thrown out of control.

Pull sawing (recommended)

Always use the bottom side of the blade for cutting branches. This technique involves sawing branches from the top to the bottom. The saw chain pulls the saw forwards, away from the user. When pull sawing, the user has much more control over the saw and can better avoid kickbacks.

Push sawing

This technique involves sawing the branch from the bottom to the top. The saw chain thus pulls the saw back towards the user. This means that the user has to equalise the rearward force of the saw chain to compensate. If the force is not equalised, there is a danger of the guide bar being pulled too far backwards so that just the tip of the bar is in contact with the branch. This can cause kickbacks or unexpected bar movement.

Lopping off branches

When sawing thinner branches, it is usually sufficient to employ the pull sawing technique. When sawing thicker branches, use the following technique:

1. Make the first cut from below, about 15–20 cm from the tree trunk. Cut about 1/3 of the way through the branch.
2. Make the second cut about 5–10 cm outside the first cut. Cut from above and cut all the way through the branch.
3. Place the third cut as close to the tree trunk as possible. Cut about 1/3 of the way through the branch. Saw from the bottom.
4. Make the fourth cut as close the tree trunk as possible and cut all the way through the branch. Saw from the top.

Diagram of a chain drive with arrows indicating motion, showing chain and gear movement (no text or symbols)

Diagram of a chain drive with gear and pulley, showing motion direction arrows (no text or symbols)

Note:

• Always begin with the branches lowest down on the trunk.
• Always stand in a well-balanced stable stance.
- Never work whilst standing on a ladder.
- Never saw off a branch which is directly above your head.
- Never overreach, lean too far forward or too far backward.
- Never work in poor light or weather conditions.
• Always use the carrying harness.
• Always hold the saw with both hands.

- Tidy the work area before beginning work and check the surroundings for foreign objects that may interfere with proper work safety.

Start

1. Remove the bar guard.
2. Loosen the knob on the carry strap attachment (6) and adjust the attachment to the desired position.
3. Slide the battery into the battery connector (4) and make sure that it clicks securely into place.
4. Push the safety catch for the power trigger (3) forwards and pull the power trigger (2). The pole saw will now start.
5. The saw will stop automatically if the power trigger is released.

Diagram of a mechanical component with an arrow indicating direction (no text or symbols present)

Care and maintenance

Hedge trimmer

Warning:

• Remove the battery from the hedge trimmer before service and maintenance.
• Wear protective gloves when handling or cleaning the blade.

- Regularly check that the safety catch for the power trigger and the power trigger are undamaged and work correctly.

- Regularly check and lubricate the blade with a suitable oil and make sure that all screws in the blade are properly tightened.

Mechanical component diagram showing a threaded shaft with multiple grooves and mounting holes (no text or symbols)

• Lubricate the blade with a suitable oil if the hedge trimmer is not to be used for a long time.
• Clean the exterior of the hedge trimmer using a damp cloth. Use only mild cleaning agents, never solvents or corrosive chemicals.

• Remove all dirt, especially from around the motor ventilation slits.

• Store the hedge trimmer in a dry, dust-free environment out of children's reach whenever it is not to be used for a long time.

• Do not store the battery in temperatures below zero.
  • Always keep the blade guard on when the hedge trimmer is not in use.

Pole saw

Warning:

• Remove the battery from the pole saw before service and maintenance.
• Wear protective gloves when handling or cleaning the guide bar and chain.
• Regularly check that the safety catch for the power trigger and the power trigger are undamaged and work correctly.
• Clean the exterior of the pole saw using a damp cloth. Use only mild cleaning agents, never solvents or corrosive chemicals.
• Remove all dirt, especially from around the motor ventilation slits.
• Do not store the battery in temperatures below zero.
  • Always put the bar guard over the pole saw when not in use and carry the saw with the bar pointing backwards when walking around.
• For proper safe and satisfactory operation, always keep the saw chain sharp and correctly tensioned. Let somebody knowledgeable about grinding saw chains take care of the grinding if you feel unsure.

Close-up of a mechanical device's internal components with a black arrow pointing to a specific part (no text or symbols visible)

Mechanical chain assembly diagram showing a clamping tool interacting with chains (no text or symbols)

• Regularly remove the chain and blade and clean the oil guide groove and the area around the chain sprocket.
• Drain the saw chain oil and store the saw horizontally in a dry, well-ventilated room out of children's reach whenever it is not to be used for a long time.

Troubleshooting guide

Pole saw/hedge trimmer does not start.	Battery discharged or incorrectly inserted.Charge the battery and make sure that it is fully inserted into the battery connector.
The pole saw/hedge trimmer is sluggish and/or cuts out.	Blade/saw chain dull or damaged.Check the blade/saw chain and replace or grind.Too much pressure applied. Decrease pressure.The battery might be overheated. Refer to the section Overload protection and other safety features.
Poor battery operating time.	The battery is not fully charged. It may take a few charging cycles where the battery is charged to 100% before full capacity is reached.The battery needs replacing.
The battery does not charge.	The battery is not correctly inserted into the charger.The battery or charger contacts are dirty.Disconnect the charger from the mains outlet and clean the contacts.The plug is not properly plugged into the mains outlet.Is the mains outlet live?The charger or the mains lead is damaged.The battery needs replacing.

Responsible disposal

This symbol indicates that this product should not be disposed of with general household waste. This applies throughout the entire EU. In order to prevent any harm to the environment or health hazards caused by incorrect waste disposal, the product must be handed in for recycling so that the material can be disposed of in a responsible manner. When recycling the product, take it to your local collection facility or contact the place of purchase. They will ensure that the product is disposed of in an environmentally sound manner.

Symbol of a trash bin crossed with no text or labels, accompanied by a blank rectangular block below (no text or symbols present)

Specifications

31-9460 Hedge trimmer

Cutter bar length 450 mm

Speed 1400 rpm (no load)

Max cutting diameter 14 mm

Noise levels LpA = 77.5 dB(A), K = 3 dB(A)

LwA = 92.4 dB(A), K = 3 dB(A)

Vibration level 1.79 m/s², K = 1.5 m/s²

Weight 3.3 kg (without battery)

Max telescopic shaft length 2.95 m

31-9461 Pole saw

Guide bar length 18 cm

Saw chain speed 5.5 m/s

Oil tank, volume 80 ml

Noise levels LpA = 79.5 dB(A), K = 3 dB(A)

LwA = 94 dB(A), K = 3 dB(A)

Vibration level 1.79 m/s², K = 1.5 m/s²

Weight 3.3 kg (without battery)

Saw chain pitch 3/8", number of links 33, appropriate file ∅ 4.0 mm

Length 194–270 cm

Vibration

- The measurement of the vibration emission level (triaxial vector sum) and the noise level values declared in this instruction manual have been carried out in accordance with a standardised test method described in EN 50636-2-91 and can be used for comparing one power tool with another.

- The measurement method may also be used for a preliminary assessment of vibration exposure.

- The declared vibration emission level applies when the power tool is used in accordance with this instruction manual. If however, the power tool is used for other purposes and with other accessories or has not been properly maintained, the vibration emission level could increase significantly over the total working period.

- For an exact assessment of the vibration exposure, the times when the tool is switched off or running idle should also be taken into account. This significantly reduces the vibration exposure over the total working period. Decide upon safety measures to protect the operator from the effects of vibration during all types of use.

Illustration of a hand holding a small black object with an arrow pointing to it, next to a black handheld device (no text or symbols present)

Mechanical assembly diagram showing a tool interacting with a cylindrical component, with directional arrows indicating motion (no text or symbols)

Mechanical component diagram showing a lever and pin assembly (no text or symbols)

Technical illustration of a chain-linking device with gear and blade (no text or symbols)

Varning!

Illustration of a hand holding a flashlight with three steps showing the process (no text or symbols present)

Mechanical component diagram showing a clamping device with a moving part (no text or symbols)

Diagram of a chain-linking gear with arrows indicating motion or flow direction (no text or symbols)

Diagram of a chain drive with gear and pulley, showing motion arrows (no text or symbols)

Mechanical component diagram showing a lever and base with directional arrow (no text or symbols)

Mechanical component diagram showing a threaded shaft with four bolt holes and downward arrows indicating force or movement (no text or symbols)

Close-up of a mechanical device's internal components with a black arrow pointing to a specific part (no text or symbols visible)

Mechanical chain assembly diagram showing a pin and chain with no visible text or symbols

Symbol of a trash bin crossed with no text or numbers, representing waste sorting or disposal (no text present)

Specifikationer

31-9460 Häcksax

Svärdlängd 450 mm

Varvtal 1400 rpm (obelastad)

Max klippdiameter 14 mm

Ljudnivåer LpA = 77,5 dB(A), K = 3 dB(A)

$$ \mathrm{LwA} = 9 2, 4 \mathrm{dB(A)}, \mathrm{K} = 3 \mathrm{dB(A)} $$

Vibration 1,79 m/s ^2 , K = 1,5 m/s ^2

Vikt 3,3 kg (utan batteri)

Illustration of a hand inserting a USB flash into a terminal block (no text or symbols)

Mechanical assembly diagram showing a tool interacting with a cylindrical component, with directional arrows indicating motion (no text or symbols)

Mechanical component diagram showing a lever and pin assembly with an arrow indicating direction (no text or symbols)

Diagram of a chain-linking device with gear and blade (no text or symbols)

Advarsel!

Illustration of a hand holding a flashlight with three steps showing the process (no text or symbols present)

Bruk

Hekksaks

Advarsel!

Diagram of a mechanical device with an arrow indicating direction (no text or symbols present)

Diagram of a chain-linking gear with arrows indicating motion direction (no text or symbols)

Saging med skyvende kjede

Diagram of a chain drive with gear and moving arrows indicating motion (no text or symbols)

Avvirking av grener

Diagram of a mechanical component with an arrow indicating direction (no text or symbols present)

Vedlikehold

Hekksaks

Advarsel!

Mechanical component diagram showing a threaded shaft with multiple grooves and mounting holes (no text or symbols)

Close-up of a mechanical device's internal components with no visible text or symbols

Mechanical chain assembly diagram showing a chain with end caps and a cutting tool (no text or symbols)

Symbol of a trash bin crossed with no visible text or labels

Spesifikasjoner

31-9460 Hekksaks

Skjærelengde 450 mm

Turtall 1400 rpm (ubelastet)

Maks klippediameter 14 mm

Illustration of a hand holding a small black object with an arrow pointing to it, next to a flashlight (no text or symbols present)

Mechanical assembly diagram showing a tool interacting with a cylindrical component, with directional arrows indicating motion (no text or symbols)

Mechanical component diagram showing a cylindrical tool with a pointed tip and an arrow indicating direction (no text or symbols)

Technical illustration of a chain-linking device with gear and blade (no text or symbols)

! Varoitus!

Illustration of a hand holding a flashlight with three steps showing the process (no text or symbols present)

Käyttö

Pensasleikkuri

Varoitus!

Diagram of a mechanical device with an arrow indicating direction (no text or symbols present)

Diagram of a chain with arrows indicating flow or movement, showing a circular object and chain links (no text or symbols)

Diagram of a chain drive with gear and moving arrows indicating motion (no text or symbols)

Oksien sahaaminen

Diagram of a mechanical component with an arrow indicating direction (no text or symbols present)

Mechanical component diagram showing a threaded shaft with four downward-pointing arrows indicating force or direction (no text or symbols present)

Close-up of a mechanical device's internal components with no visible text or symbols

Mechanical chain assembly diagram showing a chain with end caps and a cutting tool (no text or labels)

Symbol of a trash bin crossed with no visible text or labels

Tekniset tiedot

31-9460 Pensasleikkuri

Illustration of a robotic hand holding a flashlight, showing three sequential steps of tool manipulation (no text or symbols present)

Illustration of a hand holding a flashlight with three different angles (no text or symbols present)

Diagram of a mechanical component with an arrow indicating direction (no text or symbols present)

Diagram of a chain with arrows indicating motion or flow, no text or symbols present

Diagram of a chain drive with gear and motion arrows indicating movement (no text or symbols)

Abtragen von Ästen

Bitte beachten:

Diagram of a mechanical device with a lever and base, showing motion direction (no text or symbols)

Pflege und Wartung

Heckenschere

Achtung:

Mechanical component diagram showing a threaded shaft with four downward-pointing arrows indicating force or direction (no text or symbols present)

Close-up of a mechanical device's internal components with no visible text or symbols

Mechanical chain assembly diagram showing a chain with end caps and a cutting tool (no text or symbols)

Symbol of a trash bin crossed with no visible text or labels

Technische Daten

31-9460 Heckenschere

Schnittlänge 450 mm

Öltank, Volumen 80 ml

Schallpegel LpA = 79,5 dB(A), K = 3 dB(A)

$$ \mathrm{LwA} = 9 4 \mathrm{dB(A)}, K = 3 \mathrm{dB(A)} $$

Declaration of Conformity

Declares that this product complies with the requirements of the following directives and standards

Telescopic Hedge Trimmer/Hedge Trimmer Head

31-9460/31-9462

ASYPHT5450

Machinery Directive 2006/42/EC

EN 60745-1: 2009/A11: 2010

EN ISO 11680-1:2011

AFPS GS 2014: 01 PAK

EMC Directive 2014/30/EU

EN: 55014-1: 2006

+A2: 2011

EN: 55014-2: 2015

Henrik Alfredsson

Technical Manager

Insjön, Sweden, 2018-01-16

CLAS OHLSON AB, SE-793 85 INSJÖN, SWEDEN

Declaration of Conformity

Declares that this product complies with the requirements of the following directives and standards

Telescopic Pole Saw/Pole Saw Head

31-9461/31-9463

ASYPCS7200

Machinery Directive 2006/42/EC

EMC Directive 2014/30/EU

EN 60745-1: 2009/A11: 2010

EN: 55014-1: 2006

EN ISO 11680-1: 2011

+A2: 2011

AFPS GS 2014: 01 PAK

EN: 55014-2: 2015

Henrik Alfredsson

Technical Manager

Insjön, Sweden, 2018-01-16

CLAS OHLSON AB, SE-793 85 INSJÖN, SWEDEN

LXC

LITHIUM XROSS CONNECT

18V LITHIUM SERIES