DDX6027 - Autoradio multimédia KENWOOD - Free user manual and instructions

USER MANUAL DDX6027 KENWOOD

MANUEL D'INSTALLATION

Accessories © (O] 22 a 1

2 | English I B54-4468-00_(Enjindd 2 D 05.520 3:01:57 PM L

n Procedure nstalla 1.To prevent short circuits, remove the key from the ignition and disconnect the © terminal of the battery. 2.Make the proper input and output wire connections for each unit. 3.Connect the wire on the wiring harness ATake Connector B on the wiring harness and connect it to the speaker connector in your vehicle. 5.Take Connector À on the wiring hamness and connect it to the external power connector on your vehicle. 6.Connect the wiring harness connector to the unit. 7install the unit in your car. 8.Reconnect the © terminal of the battery. 9.Press the reset button B54-4468-00_(Enjindd 3 + Ifyou connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start à fire. Always connect those wires to the power source running through the fuse box + Do not cut out the fuse from the ignition wire (red) and the battery wire (yellow). The power supply must be connected to the wires via the fuse. + Ifthe power is not turned ON (or it is ON, but will be OFF immediately), the speaker wire may have a short-circuit or touched the chasis of the vehicle and the protection function may have been activated. Therefore, the speaker wire should be checked If your car ignition does not have an ACC position, connect the ignition wires to a power source that can be turned on and off with the ignition key. If you connect the ignition wire to a power source With a constant voltage supply, as with battery wires, the battery may die Ifthe console has a lid, make sure to install the unit so that the faceplate will not hit the lid when closing and opening IFthe fuse blows, first make sure the wires aren't touching to cause a short circuit, then replace the old fuse with one with the same rating Insulate unconnected wires with vinyl tape or other Similar material. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals. Connect the speaker wires correctiy to the terminals to which they correspond. The unit may be damaged or fail to work if you share the © wires or ground them to any metal part in the car. When only two speakers are being connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not mix front and rear). For example, if you connect the @ connector of the left speaker to a front output terminal, do not connect the © connector to a rear output terminal After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly. + Mount the unit so that the mounting angle is 30° or less. English | 3

K you connect the ignition wire (red) and the battery wire TV tuner (Optional) ellow to the car chassis (ground you may cause a short Giruit, that in turn may start a fre. Always connect those wéires to the power source running through the fuse box. Disc Changer etc.(Optional) Antenna Card Accessory ® FM/AM antenna input OR ES Co ———

Connection cable (included in the disc changer) Connect ta the vehicles parking brake detection switch harness the supplied relay connector. For the sake of safety, be sure to connect the parking sensor rs | Parking sensor wire (Green) . Reveres sensor wire (Pink) To Vehicle's reverse lamp harness

Connection cable Uncluded in the TV tuner)

Rear view {nciuded in the Navigation system) Wiring harness (Accessory @} Wiring hamess (Accessory @) Epinag 75e Power contral/ Motor antenna control wire {Blue/White) Ifno connections are made, do not let the cable come out from the tab. Mute wire (Brown) Connect either to the power control terminal when Qavreonr L_ecour using the optional power amplifier or to the antenna control terminal in the vehicle. Connect ta the terminal that is grounded when either External amplifier control wire EPink/Black) mure the telephone rings or during conversation. To Connect the Kenwood navigation system, consult Your navigation manual. B544468-00_(En)indd 5 Bean To "EXTAMPCONT: terminal of the amplifier having (su the external amp control function. English | 5 lan

Connecting the ISO Connector

The pin arrangement for the ISO connectors depends on the type of vehicle you drive. Make sure to make the proper connections to prevent damage to the unit. The default connection for the wiring hamess is described in [] below the ISO connector pins are set as described in [2Jor[31 make the connection as ilustrated Please be sure to reconnect the cable as shown below to install this unit to the Volkswagen vehicles etc. [] (Default setting) The A-7 pin (red) of the vehicle's 150 connector is linked with the ignition, and the A4 pin (yellow is connected to the constant power supply. Unit Vehicle Ignition wire (Red) 22 + A7 Pin (Red) Battery wire (Yellow) 2296) = @e—$ À-4 Pin (Yellow) pin (yellow) is linked to the ignition. Unit Ignition wire (Red) Battery wire (Vellow) Vehicle 2 A-7 Pin (Red) + @œ—$ À-4 Pin (Yellow) The A7 pin (red) of the vehicle's ISO connector is connected to the constant power supply, and the A-4 5] The A-4 pin (yellow) of the vehicles ISO connector is not connected to anything, while the A-7 pin (red) is connected to the constant power supply (or both the A-7 (red) and A-4 (yellow) pins are connected to the constant power supply) Unit Vehicle Ignition wire (Red) à—æ) + A7 Pin (Red)

Battery wire (Vellow) Émœ—$ 4 Pin (Yellow) + When the connection is made as in [3] above, the units power will not be linked ta the ignition key. For that reason, always make sure to tum off the units power when the ignition is tumed off. To link the units power ta the ignition, connect the ignition cable (ACC..red) to a power source that can be tumed on and off with the ignition key Connector Function Guide Pin Numbers for ISO Connectors Cable Colour Functions External Power Connector A4 Yellow Battery A5 Blue/White Power Control A6 Orange/White Dimmer A-7 Red lgnition (ACC) A-8 Black Earth (Ground) Connection Speaker Connector B-1 Purple Rear Right (+) B-2 Purple/Black Rear Right (-) B3 Gray Front Right (+) B4 Gray/Black Front Right (=) B-5 White Front Left (+) B-6 White/Black Front Left (-) B-7 Green Rear Left (+) B-8 Green/Black Rear Left (-) 6 | English B54-4468-00_(En)indd 6

Firewall or metal support Screw (M4X8) {commercial available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Self-tapping scref Metal mountingstrap Accessary @ {commercially available) {commercially available) Make sure that the unit is installed securely in place. Fthe unit is unstable, it may malfunction (eg, the sound may skip). English | 9 B54-4468-00_(Enjindd 9 05.520 3:02:01 PM

1. Engage the catch pins on the removal tool (3)

and remove the two locks on the lower level. Lower the frame and pull it forward as shown in the figure. Removal Tool (Accessory @))

2. When the lower level is removed, remove the

upper two locations. he frame can be removed from the top side in he same manner BRemoving the Unit Removal Too!

1. Remove the hard rubber frame by referring

(Accessory ®) to the removal procedure in the section <Removing the Hard Rubber Frame>.

Remove the Hex-head screw with integral washer (M4 x 8) on the back panel. . Insert the two removal tools @ deeply into the slots on each side, as shown.

Lower the removal tool toward the bottom, and pull out the unit halfway while pressing towards the inside. Be careful to avoid injury from the catch pins on he removal tool S. Pull the unit all the way out with your hands, being careful not to drop it. 10 | English B54-4468-00_(En)indd 10 05.520 3:0201 PM

n of Remote control unit nstalla Hinstall the remote control unit holder (Accessory (5)). Double-stick tape Gneladeh Remote control holder ® À prevent the Remote control uni from dropping down under our foot insal using the Remote control unit holder. IFthe Remate control unit drops down under driving pedafs, it will interfere with your driving and may result in a traffic accident English | 11 B54-4468-00_(Enjindd 11 05.520 3:02:02 PM

1.10 prevent short circuits, remove the key from the

Cable de conexiôn Uncluded in the TV tuner)