IAN 281134 - Lighting Livarno Lux - Free user manual and instructions

Product type	Outdoor LED solar light (ambient/decorative lighting)
Brand	Livarno Lux
Model	IAN 281134 (model numbers: 10346A/B/C/D/E/F)
Dimensions (without spike)	Approx. 10 x 10 x 15 cm (depending on model)
Weight	Approx. 200 g
Power supply	Solar cell + rechargeable Ni-MH battery 1.2 V, 600 mAh, AA size
Light source	4 non-replaceable LEDs, nominal power 0.025 W per LED
Protection rating	IP44 (splash-proof)
Usage	Outdoor only (ambient lighting, not room lighting)
Automatic operation	Automatic turn-on at dusk, turn-off at dawn
Assembly	On spike (included) to be inserted into the ground
Battery life	Variable depending on sunlight, up to 8 h after full charge
Charging time	Approx. 6 to 8 h of direct sunlight
Maintenance and cleaning	Clean with a dry or slightly damp cloth; solar cell must remain clean
Safety	Use only recommended battery type; observe polarity; keep out of reach of children; do not dispose of in fire
Spare parts and repairability	Rechargeable battery replaceable (AA Ni-MH type); LEDs non-replaceable; no other spare parts available
Warranty	36 months from date of purchase
General information	Manufacturer: Uni-Elektra GmbH, Kirchstr. 48, DE-72145 Hirrlingen, Germany; After-sales service: 00800 888 11 333 or [e-mail]

Frequently Asked Questions - IAN 281134 Livarno Lux

How to install the solar light?

Insert the spike into the ground in a sunny location. Turn the ON/OFF switch to ON. Mount the lamp body onto the spike, then screw on the shade with the solar cell housing.

Why doesn't my lamp turn on at night?

Check that the switch is ON. Make sure the solar cell gets enough direct sunlight during the day and is not obstructed. Keep the lamp away from artificial light sources (streetlights) that may prevent it from turning on.

How to replace the battery?

Unscrew the shade and remove the solar cell housing. Set the switch to OFF. Loosen the screws on the battery compartment, replace the old battery with a new one (Ni-MH AA 1.2 V) observing polarity. Close and set the switch back to ON.

What type of battery to use?

Use a rechargeable Ni-MH battery, AA size, 1.2 V, 600 mAh (included). Do not use non-rechargeable batteries.

Can the lamp be used indoors?

No, this product is designed for outdoor use only (ambient/decorative lighting). It cannot be used as room lighting.

How to clean the solar light?

Clean the lamp regularly with a dry, lint-free cloth. For stubborn dirt, use a slightly damp cloth. Ensure the solar cell remains clean to guarantee proper charging.

What if the lamp only turns on for a short time?

The battery may be worn out or the charge insufficient. Replace the battery or place the lamp in a sunnier location.

Can I replace the LEDs?

No, the LEDs are built-in and cannot be replaced.

How to store the lamp in winter?

Clean the lamp and store it in a dry, heated room. Remove the battery if not used for a long time.

What to do in case of malfunction?

First check the user manual. If the problem persists, contact after-sales service: 00800 888 11 333 or [e-mail]. Have the receipt and IAN 281134 reference ready.

USER MANUAL IAN 281134 Livarno Lux

LED-SOLARLEUCHTE/LED SOLAR LIGHT BALISE SOLAIRE À LED

DE AT CH

LED-SOLARLEUCHTE

Assembly, operating and safety instructions

NL BE

LED-SOLARLAMP

Before reading, unfold both pages containing illustrations and familiarise yourself with all functions of the device.

FR BE

List of pictograms used....Page 14

Introduction......Page 14

Intended Use Page 14

Parts Description......Page 14

Scope of delivery....Page 14

Technical Data Page 15

Safety Notices......Page 15

Product-specific safety instructions ......Page 15

Safety instructions for rechargeable batteries....Page 15

Functionality Page 16

Initial use Page 16

Mounting the light....Page 16

Installing the light Page 16

Replacing the rechargeable battery Page 17

Charging......Page 17

Maintenance and Cleaning......Page 17

Troubleshooting Page 18

Disposal Page 18

Warranty and Service......Page 18

Service address......Page 19

Manufacturer......Page 19

List of pictograms used
	Read the instructions! Caution! Expl hazard!
	Volt (direct current) Caution! Fire hc
	Watt (effective power) Wear safety is!
	Observe the warnings and safety notices!		Caution - Hot surfaces!
	This product is not suitable as residential room lighting.		Dispose of the packaging and product in an environmentally-friendly manner!
	Accident hazard and risk of fatal injury for infants and children!		Improper disposal of rechargeable batteries may result in environmental damage!
[Y8CK]	Severe or fatal injuries may occur.

LED solar light

- Introduction

Familiarise yourself with the device before using it for the first time. In addition, please carefully refer to the instructions

for use and the safety instructions below. Only use the product as described and for the indicated purpose. Keep these instructions in a safe place. If you pass the device on to anyone else, please ensure that you also pass on all the documentation.

Intended Use

The solar light is intended as outdoor ambient/decorative lighting. The integrated solar cell and the rechargeable battery allow usage independent from the electricity grid. Any modification to the product are considered improper use and may result in considerable hazards. The manufacturer

assumes no liability for damages due to improper use. This device is not intended for commercial use.

Parts Description

1 Lamp shade
2 Solar cell housing
3 Lamp body
4 Ground stake (model 10346A/B/C/D)
5 Adapter (model 10346A/B/C/D)
6 Solar cell
7 ON/OFF switch
8 Fastening screw
9 Battery compartment
10 Rechargeable battery

- Scope of delivery

1 LED solar light
1 Rechargeable Ni-MH battery, AA, 600 mAh, 1.2 V---
1 Set of assembly instructions and instructions for use

- Technical Data

Model no.: 10346A/10346B/

10346C/10346D/

10346E/10346F

Dimensions (without

ground stake): 10346A/10346B:

approx. 50 x 10 x 10 cm

(h x w x d)

10346C / 10346D:

approx. 15 x 40 cm

(∅ x h)

10346E/10346F:

approx. 39 x 13.5 x

13.5 cm (h x w x d)

Rechargeable battery: 1 x Ni-MH, AA, 600 mAh,

1.2V=

Light bulb: 4 x LED (not replaceable)

Rated output LED: approx. 0.025 W per LED

Protection type: IP44 (splash-proof)

Safety Notices

PLEASE READ THE INSTRUCTIONS PRIOR TO USE! PLEASE KEEP THE INSTRUCTIONS IN A SAFE PLACE! IF PASSING THIS PRODUCT ON TO A THIRD PARTY, INCLUDE ALL DOCUMENTS!

This product may be used by children aged 8 years and up, as well as by persons with reduced physical, sensory or mental capacities, or lacking experience and/or knowledge, so long as they are supervised or instructed in the safe use of the product and understand the associated risks. Do not allow children to play with the product. Cleaning and user maintenance should not be performed by children without supervision.
Do not use the product if you detect any type of damage.
Switch the product off whilst storing in a dark environment to prevent draining the battery.

Product-specific safety instructions

■ Make sure the solar cell is free of dirt and free of snow and ice in winter. Otherwise the performance of the solar panel will be diminished.
Cold temperatures negatively impact the battery operating time. If the solar garden light will not be used for extended periods, e.g. in winter, it should be cleaned and stored in a dry, warm location.

This product is not suitable as residential room lighting.

Safety instructions for rechargeable batteries

RISK OF WARNING!

CIDENT AND DANGER TO LIFE FOR INFANTS AND CHIL-

DREN! Rechargeable batteries are not intended to be in the hands of children. Do not leave the batteries lying around. There is a danger that these will be swallowed by children or pets. If they are accidentally swallowed seek immediate medical attention.

CAUTION! EXPLOSION HAZ-

ARD! Only use the recommended type of rechargeable batteries.

Other rechargeable or single-use batteries could explode during charging.

FIRE HAZARD! Never short-circuit rechargeable batteries. Otherwise the rechargeable batteries may overheat, become a fire hazard or explode.

CAUTION! EXPLOSION HAZ-

ARD! Never throw rechargeable batteries into fire or water.

- Expired or drained rechargeable batteries may leak chemicals which will damage the product. Remove, therefore, the rechargeable battery when the lamp is not required for any length of time.

WEAR PROTECTIVE GLOVES!

Leaked or damaged rechargeable batteries could cause chemical

burns on contact with the skin; you should therefore wear suitable protective gloves at all times if such an event occurs.

Only use rechargeable batteries of the correct size and the recommended type (see section "Technical Data").
■ Ensure correct polarity, indicated in the battery compartment.

Functionality

The solar cell built into the product converts sunlight into electricity and stores it in a Ni-MH rechargeable battery. The light switches on at dusk. The built-in LED is an energy-saving light bulb with a very long life. The light duration depends on the amount of sunlight, the angle at which light hits the solar panel, and the temperature (the battery capacity varies by temperature). A vertical angle of light at temperatures above the freezing point is ideal. The rechargeable battery will only achieve its maximum capacity after several charging and discharging cycles.

- Initial use

- Mounting the light

10346A/B:

☐ Pull the solar cell housing 2 including lampshade 1 out of the lamp body 3.
☐ Push the ground stake 4 out of the adapter 5 and into the lamp body 3.
☐ Push the ground stake 4 into the ground in the desired location and attach the lamp body 3.
☐ Set the ON/OFF switch 7 to the position marked „ON“ to allow the product to switch on in the dark.
☐ Reattach the solar cell housing 2 with lamp shade 1 to the lamp body 3. Your solar light is now ready to use.

10346C/D:

☐ Pull the solar cell housing 2 including lamp-shade 1 out of the lamp body 3.
☐ Push the ground stake 4 out of the adapter 5 and into the lamp body 3.
☐ Push the ground stake 4 into the ground in the desired location and attach the lamp body 3.
☐ Turn the solar cell housing 2 out of the lamp-shade 1 counter-clockwise.
☐ Set the ON/OFF switch 7 to the position marked „ON“ to allow the product to switch on in the dark.
☐ Insert the solar cell housing 2 into the lampshade 1 and tighten clockwise. Your solar light is now ready to use.

10346E/F:

☐ Pull the solar cell housing 2 off the lamp shade 1.
☐ Set the ON/OFF switch ☐ to the position marked „ON“ to allow the product to switch on in the dark.
☐ Reattach the solar cell housing 2 to the lamp shade 1. Your solar light is now ready to use.

• Installing the light

10346A/B/C/D:

☐ Push the ground stake 4 far enough into the ground (lawn, flower bed) so it is firmly positioned upright in the ground. Then attach the assembled solar light to the ground spike 4.
☐ Make sure it is firmly positioned. Do not use force when assembling or setting up the product, e.g. hammer blows. This will damage the product. In order to achieve the best result, set the solar garden lamp up in a place where the solar cell will get direct sunlight for as long as possible.
☐ Make sure the solar cell is not impacted by other light sources, e.g. yard or street lighting, or the light will not switch on at dusk.
☐ The light will automatically switch on in low light and switch off in normal daylight.

● Replacing the rechargeable battery

The batteries should be replaced every 12 months to ensure optimum performance.

10346A/B:

☐ Remove the lampshade 1 from the lamp body 3.
☐ Pull the solar cell housing ☐ out of the lampshade ☐ 1.
☐ Switch off the light using the ON/OFF switch 7 by setting the switch to the „OFF" position.
☐ Remove the fastening screws 8 using a small cross-tip screwdriver. Then open the battery cover on the solar cell housing 2 using a flat-head screwdriver.
☐ Replace the old battery 10 with a new rechargeable battery, taking care not to damage the cables. Please note the polarity when inserting the battery. This is shown inside the battery compartment 9. Use only rechargeable batteries of the recommended type (see „Technical Data”).
☐ Close the battery cover and tighten the retaining screws 8 using a small cross-tip screw-driver. Set the ON/OFF switch 7 to the "ON" position.
☐ Reattach the solar cell housing 2 to the lamp shade 1. Then assemble the remaining parts of the lamp.

10346C/D:

☐ Remove the lampshade 1 from the lamp body 3.
☐ Turn the solar cell housing 2 out of the lampshade 1 counter-clockwise.
☐ Switch off the light using the ON/OFF switch ☐ 7 by setting the switch to the „OFF" position.
☐ Remove the fixing screws 8 using a small cross-tip screwdriver.
☐ Replace the old battery 10 with a new rechargeable battery, taking care not to damage the cables. Please note the polarity when inserting the battery. This is shown inside the battery compartment 9. Use only rechargeable

batteries of the recommended type (see „Technical Data“).

☐ Tighten the retaining screws 8 with a small cross-tip screwdriver. Set the ON/OFF switch 7 to the „ON” position.
☐ Reattach the solar cell housing 2 to the lamp shade 1. Then assemble the remaining parts of the lamp.

10346E/F:

☐ Pull the solar cell housing 2 off the lamp shade 1.
☐ Switch off the light using the ON/OFF switch ☐ 7 by setting the switch to the „OFF" position.
☐ Use a small cross-tip screwdriver to remove the fastening screws 8.
Replace the old battery 10 with a new rechargeable battery, taking care not to damage the cables. Please note the polarity when inserting the battery. This is shown inside the battery compartment 9. Use only rechargeable batteries of the recommended type (see „Technical Data”).
☐ Tighten the retaining screws 8 with a small cross-tip screwdriver. Set the ON/OFF switch 7 to the „ON” position.
☐ Reattach the solar cell housing 2 to the lamp shade 1.

- Charging

Please note, the solar garden light must be switched on when the battery is charging. The charging time via the solar cell varies by the intensity of the sunlight and the incidence angle of light onto the solar cell. Place the solar cell as perpendicular as possible to incidence angle of light. This will ensure the brightest light.

● Maintenance and Cleaning

The LEDs cannot be replaced. The solar lamp is maintenance-free, except for any necessary change of battery.

☐ Routinely clean the solar light with a dry, lint-free cloth. Use a slightly moist cloth if very dirty.

- Troubleshooting

Note: The device contains sensitive electronic components. Radio transmitting equipment in the immediate vicinity may therefore cause interference. If you notice the device is malfunctioning, remove any sources of interference from the area around the device.

Note: Electrostatic discharge can cause malfunctions. In the event of such malfunctions, briefly remove and reinsert the rechargeable batteries.

Error Cause Solution
The light will not switch on even though the sun shone on the lamp all day.	Artificial sources of light, e.g. street lighting, is interfering with the light.	Place the light in a location where it will not be affected by other light sources.
The light does not come on or comes on only briefly.	The rechargeable battery is broken or there was not enough daylight.	Replace the battery or install the light in a location where it has greater exposure to sunlight.

●Disposal

The packaging is made entirely of recyclable materials, which you may dispose of at local recycling facilities.

Contact your local refuse disposal authority for more details of how to dispose of your worn-out product.

To help protect the environment, please dispose of the product properly when it has reached the end of its useful life and not in the household waste. Information on collection points and their opening

hours can be obtained from your local authority.

Defective or old rechargeable batteries must be recycled in accordance with Directive 2006 / 66 / EC and its amendments. Return rechargeable batteries and / or the device to the recycling facilities provided.

Improper disposal of rechargeable batteries may result in environmental damage!

Never dispose of rechargeable batteries in your household waste. They may contain toxic heavy metals and are subject to hazardous waste regulations. The chemical symbols of the heavy metals are: Cd = cadmium, Hg = mercury, Pb = lead. For this reason, dispose of used rechargeable batteries at a local collection point.

- Warranty and Service

Note: this product includes a 36 month warranty from the date of purchase. The product has been produced to the highest standards and thoroughly checked before dispatch. However, if defects in manufacturing or material arise during the warranty period, please contact your retailer immediately.

The warranty does not cover damages due to improper handling, failure to comply with the operating instructions, or manipulation by unauthorised persons. Most malfunctions are caused by incorrect operation. Therefore please first refer to the operating instructions if a malfunction occurs.

Please contact the Uni-Elektra GmbH service address with any questions. The product can only be returned to us after contacting us. Postage due shipments will not be accepted. Warranty services do not extend or restart the warranty period of 36 months.

- Service address

Uni-Elektra GmbH

Kirchstr. 48

DE-72145 Hirrlingen / GERMANY

Tel.: [phone]

GB [e-mail]

IE [e-mail]

IAN 281134

Please have your receipt and the item number (e.g. IAN 12345) ready as your proof of purchase when enquiring about your product.

Manufacturer

Uni-Elektra GmbH

Kirchstr. 48

DE-72145 Hirrlingen / GERMANY

CE IP44

50 × 10 × 10 cm (H × l × P)

10346C / 10346D:

env. 15 x 40 cm (∅ x H)

10346E / 10346F: env.

39 × 13,5 × 13,5 cm (H × I × P)

Pile: 1 x Ni-MH, AA, 600 mAh, 1,2

NOSTE OCHRANNÉ RUKA-

Legenda dos pictogramas utilizados ...... Página 54

ktra GmbH

Kirchstr. 48

DE-72145 Hirrlingen

GERMANY