IAN 96002 - Lighting Livarno Lux - Free user manual and instructions

USER MANUAL IAN 96002 Livarno Lux

www.lidl-service.com PDF online

SOLAR-LED-LEUCHTE 1-FLAMMIG 54241

DE

LED-SOLAR

Bedienungsanleitung

NL

LED-SOLAR

gebruiksaanwijzing

GB

LED-SOLAR

Instructions

EN Congratulations on the purchase of your new lamp.

You have chosen a device of premium quality. The instruction manual is part of this device and contains important safety, usage and disposal instructions for the device.

Be sure to carefully read all safety and usage instructions before operation. Only use the device as described and for the purposes specified. When giving the device to third parties, make sure that all the relevant documents are handed over together with the devic

Technical diagram illustrating three stages of a mechanical or electrical setup with labeled components and directional arrows.

DE Deutsch / Solar-LED-Leuchte 1-flammig

EN English / Decorative solar stone LED lamp with one light

Use, safety guidelines, replacing the battery.... 7

commissioning, malfunctions.... 8

Normal and safe operation, technical data 9

Warranty, service.... 10

EDI Light Service Center

c/o RTS Service Solutions

Halle 17-1

Use, safety guidelines, replacing the battery

Using the operating instructions

Read all the instructions in this manual carefully before assembling, mounting or switching on the light and follow them without exception.

Observing all of the guidelines guarantees safe operation and manufacturer's warranty where applicable.

Keep these instructions in a safe place for future reference.

Remember to pass these instructions on to new owners of the lights.

Lamp function

Solar LED lamp

with an ON/OFF switch

Ground spike

2 spacer tubes for 2 versions

IPX4

Important safety information

Intended use

The LED solar lamp is suitable for constant use outdoors. It is designed for use in private households and is not suitable for commercial purposes.

Do not use the LED solar lamp if there is visible damage. The lamp is protected against spray water, but must not be submerged in water. The solar module should not be glued down, covered or painted.

Do not operate the LED solar lamp with normal batteries that are non-rechargeable. Do not take the batteries apart, throw in fires or short wire.

Danger to children and people with limited capability of using the devices

Children and people with limited capability do not recognise the dangers associated with using electrical devices. Keep away from children and people with limited capability.

Keep packaging and wrapping away from children and people who are of a limited ability to operate devices. Danger of suffocation!

Batteries can be fatal if swallowed. Keep batteries and the product out of the reach of small children. In the event of a battery being swallowed, seek medical assistance immediately.

Replacing the battery

1. The battery is designed to operate for long durations. However, it may be necessary to change the battery in the event of a long period of use.
   Batteries are subject to natural wear and tear and their performance can decrease.
2. Unscrew the ball counterclockwise.
3. Turn the solar unit switch to OFF.
4. After loosening the two screws on top of the solar unit by counter clockwise rotation, turn the solar unit over.
5. Remove the battery and replace it with a new, fully charged battery of the same type (see "Technical specifications"). Make sure the battery is inserted according to the right polarity (+/-).
6. Put the solar unit back into place and secure it with the two screws using clockwise rotation.
7. Turn the switch back to ON.
8. Fix the ball into the base by clockwise rotation as far as it goes.

commissioning, malfunctions

Observe all of the instructions and warnings. Improper use or incorrect operation can lead to serious physical injury (e.g. from electric shock or burning) and substantial material damage (e.g. from fire).

Storage and transport

Store and transport the lamp only in its original packaging. Protect packaged light from mechanical impact, moisture, frost and dust.

Comes with

Lamp with solar panel, incl. 1x LED + accumulator, 1 Plastic ball, 2 spacer tubes for 2 versions, 1 Ground spike, user manual

Unpacking

Take all the parts of the lamp out of the box and remove the packaging material. Put all the parts of the lamp on a soft surface in front of you, such as a carpet. Check the parts for any possible visible damage.

Commissioning

1. The solar LED lamp can be positioned independent of a power source.

The LED solar lamp comes equipped with a ground spike. You can only use the LED solar lamp together with the ground spike. In this case you have 2 selection possibilities with the 2 provided spacer tubes (see figure on page 1). When using or positioning, the following should be considered: position the ground spike in the provided recess on the bottom of the lamp, making it possible for you to push the lamp straight into soft ground (e.g. meadow, bed, etc.).

However, because the lamp depends upon energy from the sun, you must consider the following points when setting up the lamp and act accordingly:

Choose a place where the solar module is exposed to direct sunlight during the day.

Avoid placing at a location lying entirely or mostly in the shade (trees, roof gable, etc.).

The solar module should not be permanently exposed to other light sources at night, for example, by a spotlight illuminating a garage entrance, etc.

Please consider that many light sources only switch on in the middle of the night or when movement is detected.

1. This lamp has a twilight sensor and an ON/OFF switch. The lamp provides light for approx. 6 to 8 hours when fully charged.

2. Loosen the ball from the base (solar unit) by counter clockwise rotation. Before initial commissioning turn the ON/OFF switch to ON. Fix the ball into the base by clockwise rotation as far as it goes. Expose the LED solar lamp to sunlight.

3. LED solar lamp function: ON - The LED solar lamp automatically switches on when the area starts to get dark. The lamp automatically switches off when the area starts to get light. If there is sufficient brightness, the battery starts to charge.

OFF - The LED solar lamp is permanently off. If there is sufficient brightness, the battery starts to charge.

Disposal of packaging

Dispose of the packaging material, sorting it according to type.

Keep packaging and wrapping away from children. Danger of suffocation!

Damage and malfunctions

LEDs do not light:

Environment too light? Check if light from other sources is hitting the solar lamp. If so, change the location of the lamp. (e.g. street lights or lamps which are controlled by time or motions)

Battery fully charged? See "Replacing the battery".

LEDs are damaged: The LEDs cannot be replaced.

The light from the LEDs is dim: Battery is not fully charged or damaged; charge the battery in the battery charger or replace with a new battery.

The power fluctuates depending on the time of year: this is due to the weather and is not a fault. The weather conditions in summer are most favorable and least favorable in winter.

Normal and safe operation, technical data

Normal and safe operation

All the information provided must be adhered to for safe operation and to avoid risking your manufacturer's warranty. Only operate the lamp with the specified battery voltage. The lamp is not a toy. Keep it away from children and people who are of a limited ability to operate devices.

Cleaning

Only clean the surface of the lamp. Use a soft, damp cloth to clean the lamp.

Disposal

Please dispose of the article in the appropriate manner following the current legal regulations. Information on this is available from the local municipal services. This solar lamp contains a NiMH battery. This must be disposed of separately and may not be thrown away with household waste.

BATTERY LEAKAGE

If a battery has leaked, try to remove the fluid from the battery compartment with a soft cloth. Exposure to leaking batteries may cause chemical burns. Make sure that the battery fluid does not come into contact with your skin or eyes. Should this happen nevertheless, immediately try to remove the battery fluid by rinsing under cold running water. Seek medical advice.

Technical data

Article code 54241

Type

Voltage Battery (1x per lamp)

IP class IPX4

1x LED light (not replaceable) Bulb:

Technical data Battery Akku NiMH 1,2V AA 300mAh

Distributor: Edi Light GmbH, Heiligkreuz 22, A-6136 Pill

IP protection class

IPX4

This lamp is suitable for outdoor use.

Declaration of conformity

This product meets the standards of the appropriate European and national guidelines. Corresponding explanations and documents are provided by the manufacturer. The product meets the standards of the German device and product safety law.

In the course of improving products, we reserve the right to make technical and visual alterations.

Subject to error and omissions.

Warranty, service

We provide a 3 year warranty from date of sale

Our products are manufactured in line with the latest methods and undergo precise quality testing. We guarantee the article's faultless quality. We will remedy any material or manufacturing defects free of charge within the warranty period. Should defects contrary to expectations become apparent, carefully send the packaged article to the service address provided.

Excluded from the warranty are damages based on improper handling, as well as worn parts and consumables. These can be ordered at the owner's expense by calling the number given.

Repairs not included in the warranty (e.g. light bulbs), can also be arranged at cost price at the service address provided. The article will be repaired by the service address provided. Timely handling and return postage can only be carried out if you send it directly to this address.

If you require further information, would like to order accessories or have questions about servicing, please call our customer advice line on the number provided. Please have the article number ready for enquiries (see technical details).

Service address

Great Britain

EGLO UK Ltd.

Unit 12 Cirrus Park

Lower Farm Road

Moulton Park Industrial Estate

GB- Northampton, NN3 6UR

E-Mail: [e-mail]

Telephone: [phone]

Warranty card

Please fill in this section in block capitals and enclose the device.

Sender:

Surname/First name:

State/Postcode/Town/Street:

Telephone number:

Article number/Article description:

Purchase date/Purchase location:

Description of fault:

Date/Signed:

No warranty case presented:

Please send the article back unrepaired against transport costs incurred.

Advise me of the costs. Repair the article at a cost.