PSSP 2 A1 - Uncategorized PARKSIDE - Free user manual and instructions

Product Type	Grinding discs for angle grinders
Brand	Parkside
Model	PSSP 2 A1
Intended Use	Grinding metal workpieces and removing rust
Commercial Use	Not intended for commercial use
Material	Abrasive material (specific type not specified in manual)
Storage Conditions	Cool, dry place, protected from mechanical stress and moisture
Expiry Date	Printed on disc (e.g., 08/2024)
Pre-Use Inspection	Check for damage; do not use damaged discs
Speed Compatibility	Disc speed must not exceed max speed of power tool
Mounting Instructions	Follow disc and tool manufacturer instructions; ensure correct fit and use proper flanges
Test Run	Perform a short test run after mounting
Grinding Angle	10–15° relative to workpiece
Grinding Pressure	Light and steady pressure
Required Safety Gear	Safety goggles, ear protection, dust mask, gloves, protective clothing
Kickback Prevention	Firm grip, avoid binding in corners, keep body out of kickback path
Safety Cover	Must be attached and adjusted to minimize exposed disc area
Symbols on Disc	Yes (see manual for explanation of all symbols)
Disposal	Recycle packaging; dispose worn discs according to local regulations
Manufacturer Contact (UK)	Tel: [phone], Email: [e-mail]

Frequently Asked Questions - PSSP 2 A1 PARKSIDE

What is the intended use of these grinding discs?

These grinding discs are designed for grinding metal workpieces and removing rust. They are intended for private use only and not for commercial applications.

Can I use these discs for cutting metal?

No, these discs are specifically for grinding and not for cutting. Using them for cutting may cause the disc to break and result in injury. Always use the correct type of disc for your application.

What safety equipment should I wear when using these discs?

You should wear safety goggles, ear protection, a dust mask, protective gloves, and protective clothing. For heavy grinding, a full face shield is also recommended.

How should I store the grinding discs?

Store discs in a cool, dry place away from moisture and mechanical stress. Handle them carefully to avoid damage. Check the expiry date before use.

How do I mount the grinding disc correctly?

Ensure the disc fits exactly on the spindle and use the correct flanges. Follow the instruction of both the disc and the power tool manufacturer. After mounting, perform a short test run at low speed.

What is the correct angle for grinding?

Hold the angle grinder so the disc contacts the workpiece at an angle of 10 to 15°. Apply light, steady pressure and move the grinder back and forth smoothly.

What should I do if a disc is damaged?

Do not use a damaged disc. Discard it properly according to local regulations. Always inspect discs before use for cracks, tears, or other damage.

How can I prevent kickback when grinding?

Maintain a firm grip on the tool, use the additional handle if available, and avoid binding the disc in corners or sharp edges. Keep your body out of the kickback path.

What do the symbols on the disc mean?

The symbols indicate important safety information, such as wear eye protection, use a dust mask, not for hand-held use, and only for grinding. Refer to the manual for a full explanation.

How do I dispose of worn-out grinding discs?

Dispose of worn discs according to local waste disposal regulations. The packaging is recyclable. Contact your local authority for specific guidelines.

USER MANUAL PSSP 2 A1 PARKSIDE

GRINDING DISCS PSSP 2 A1

GB

GRINDING DISCS

Assembly, operating and safety instructions

EE

LIHVKETTAD

GB Assembly, operating and safety instructions Page 3

Safety instructions.... Page 5

General safety instructions for grinding discs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Selecting grinding discs for proper use .... Page 6

Storing grinding discs.... Page 6

Before using grinding discs .... Page 6

Instructions for mounting .... Page 7

Grinding operation ...... Page 7

Safety instructions for all types of use .... Page 8

Kickback and related safety instructions .... Page 11

Safety instructions for grinding....Page 12

Installation Page 14

Meaning of symbols....Page 15

Disposal Page 18

GRINDING DISCS

Introduction

We congratulate you on the purchase of your new product. You have chosen a high quality product. Familiarise yourself with the product before using it for the first time. In addition, please carefully refer to the operating instructions and the safety advice below. Only use the product as instructed and only for the indicated field of application. Keep these instructions in a safe place. If you pass the product on to anyone else, please ensure that you also pass on all the documentation with it.

- Intended use

This product is designed for grinding workpieces and removing rust from metal. Any other usage is considered improper and carries a significant risk of accidents. The manufacturer accepts no responsibility for damage(s) resulting from improper usage.

This product is not intended for commercial use.

Safety instructions

BEFORE FIRST USE, FAMILIARIZE YOURSELF WITH THE PRODUCT'S INSTRUCTIONS FOR USE AND SAFETY INSTRUCTIONS! IF YOU GIVE THE PRODUCT TO A THIRD PARTY, YOU MUST INCLUDE ALL DOCUMENTS. SAVE ALL SAFETY INSTRUCTIONS AND INSTRUCTIONS FOR USE FOR FUTURE REFERENCE!

● General safety instructions for grinding discs

• Grinding discs are prone to breakage. Exercise extreme care when handling grinding tools.
• Check grinding discs for damages before use. Do not use any damaged discs or incorrectly assembled grinding discs.
• Grinding discs are not allowed to be used after the expiration date. The valid date is shown on the discs.

- Selecting grinding discs for proper use

- Heed all safety instructions belonging to the grinding discs as well as the notes on proper use or safety instructions.

- Storing grinding discs

■ Handle and transport grinding discs with care.

■ Store grinding discs so that they are not exposed to mechanical stress or damaging environmental factors (i.e. moisture).

Before using grinding discs

■ Always check grinding discs for damages before use.
- Do not use any damaged grinding discs.
■ Rust build-up or other signs of chemical or mechanical alteration to the fitting equipment may cause premature failure of the grinding discs.
- Grinding discs may not be mounted to machines whose speed exceeds the maximum speed of the grinding discs.
Before use, please study the manual of your power tools.

- Instructions for mounting

■ Following the instructions included with the grinding disc and those of the machine manufacturer to mount grinding discs.

■ Make sure to use grinding discs only with devices that have an appropriate tool attachment.

■ After mounting, always do a small test run. Do not exceed the maximum labelled speed of the grinding disc.

Grinding operation

■ Follow the instructions for use provided by the power tool manufacturer.

■ Mount all safety attachments to the machine before use.

- Use appropriate personal safety equipment depending on the machine and type of use, such as: protect face and eye wear, ear protection, respiratory protection, safety shoes, safety gloves and any other necessary protective clothing.

■ Use the grinding disc for appropriate grinding jobs only.

■ Correct angle: Hold the grinder at an angle of approx. 10 to 15°.

■ Correct pressure: Apply light, steady pressure.

■ Move the angle grinder back and forth steadily.

■ Turn off your hand-held angle grinder and allow it to stop rotating before setting it down on the ground or your workbench.

● Safety instructions for all types of use

Safety instructions for grinding

• Do not use any equipment not expressly intended for use with and recommended by the manufacturer. The ability to successfully mount equipment to your power tool guarantees safe use in no way.
  The maximum speed of the attachment must be at least as high as that of the power tool. Running attachments at speeds that exceed their maximum rated speed may cause them to break, release from the power tool and cause injury.
  The exterior diameter and thickness of the attachment must correspond to the size requirements of your power tool. Incorrectly measured attachments cannot be sufficiently shielded or controlled.

• Grinding discs must fit exactly on your power tool's reception spindle. Attachments that do not fit exactly on your power tool's reception spindle turn unevenly, vibrate heavily and may cause a loss of control.

• Do not use any damaged attachments. Before use, always check your attachments for damages. Check grinding discs for cracks and tears.
  If you drop a power tool or attachment, check it for damages or use undamaged attachments. You and all people in your vicinity should keep on a different level as the rotating attachment as soon as you have mounted it.
  ■ Wear personal protective clothing. If necessary, wear a full protective mask, eye protection or safety glasses. If necessary, wear a dust mask, ear protection, protective gloves or a protective apron to shield yourself from cutting and material particles. Safety glasses shield your eyes from airborne foreign objects that may develop during many types of work. A dust mask or respiratory protection filter dust. Extended exposure to loud noises may lead to hearing loss.

■ Make sure that anyone who enters your workspace is wearing appropriate personal protective clothing. Broken pieces of the object you are working on or broken pieces from your tool attachments may fly around and cause injury even outside your direct working vicinity.
- Keep the power cable away from all rotating tool attachments. If you lose control of the device, the power cable may be severed or caught, causing the rotating attachment to come into contact with your hand or arm.
- Allow all tool attachments to come to a complete stop before setting down your power tool. Rotating attachments may come into contact with the surface. This may cause you to lose control of the power tool, leading to injury of yourself or others.
■ Turn off the power tool when carrying it about. Your clothing may otherwise become tangled up in the rotating attachment, causing personal injury.
- Do not use the power tool near flammable materials. Sparks may ignite such materials.

- Kickback and related safety instructions

Kickback is a sudden reaction arising when a rotating power tool attachment, such as a grinding disc, snags or jams.

Kickback is the result of improper use of the power tool. Heed the following safety precautions to prevent kickback:

■ Always maintain a firm grip on the power tool and use any available additional handle to better control kickback.

- Keep your hands away from rotating tool attachments at all times. The attachment may come into contact with your hand in case of kickback.

- Keep your body out of the area that the power tool would enter in case of kickback. In case of kickback, your power tool will jump in the direction opposite to that in which the grinding disc is moving.

Exercise extreme caution when working on corners, sharp edges, etc. Prevent your tool attachments from jumping back from the workpiece and jamming. The rotating tool attachment tends to jam when working on corners, sharp edges or when it jumps back from the workpiece. This leads to loss of control or kickback.

● Safety instructions for grinding

The safety cover must be attached to the power tool and adjusted so that maximum safety is guaranteed, that is, as little of the grinding disc as possible is open toward the operating individual. The purpose of the safety cover is to shield the operating individual from broken pieces or accidental contact to the grinding disc.

Only use disc types that are recommended for your power tool. Always use the specific guard designed for the selected disc. Discs for which the power tool was not designed cannot be adequately guarded and are unsafe.

The grinding surface of centre depressed grinding discs must be mounted below the plane of the guard lip. An improperly mounted grinding disc that projects through the plane of the guard lip cannot be adequately protected.

Always use undamaged clamping flanges of the right size and proper form for the grinding disc you have selected for use. The right flange supports the grinding disc and thus minimizes the risk of it breaking. Flanges for cutting discs may differ from flanges for grinding discs.

Installation

● Meaning of symbols

Not approved for hand-held or manually-guided grinding

Only approved for wet grinding

Not approved for side grinding

Do not use if damaged

Only approved with a backing pad

Not approved for wet cutting

Heed all safety instructions

Use protective eyewear

Wear a safety helmet

Use ear protection

Wear safety gloves

Use a dust mask

Unplug

Only for roughing / Only for grinding

Two technical diagrams showing mechanical assembly or tool positioning, with no visible text or symbols.

Not for roughing

Two diagrams showing a hammer cutting a surface with a tool, no text or symbols present

Only for cutting

Not for cutting

Not approved for working with metals

Only approved for working with metals

● Disposal

The packaging is made entirely of recyclable materials, which you may dispose of at local recycling facilities.

Contact your local refuse disposal authority for more details of how to dispose of your worn-out product.

Service

GB

Service Great Britain

Tel.:[phone]

E-Mail:[e-mail]

Expiry date: 08/2024

Production date: 08/2021

Two technical diagrams showing mechanical assembly or tool positioning (no text or symbols)

Two diagrams showing a tool pressing down on a surface, with no visible text or symbols.

Ainult lõikamiseks

Ei ole lõikamiseks

E-postiaadress:[e-mail]

Two technical diagrams showing mechanical assembly or machining process with no visible text or symbols

Two diagrams showing a tool pressing on a surface, with no visible text or symbols.

Tikai griešanai

Nelietot griešanai

Two technical diagrams showing mechanical assembly or tool positioning (no text or symbols)

Nicht zum Schruppen

Two diagrams showing a tool pressing down on a surface, with no visible text or symbols.

Nur zum Trennen

Nicht zum Trennen