BOSS200/1 - Sander Vevor - Free user manual and instructions

USER MANUAL BOSS200/1 Vevor

Affordable. Reliable. Home Improvement.

SPINDLE SANDER

MODEL: BOSS200&BOSS200/1

VEVOR

Affordable. Reliable. Home Improvement.

SPINDLE SANDER

MODEL:BOSS200&BOSS200/1

Two orange industrial machines with black caps and mechanical components, shown from different angles (no text or symbols visible)

BOSS200 BOSS200/1

This is the original instruction, please read all manual instructions carefully be operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you again if there are any technology or so it updates on our product.

	Warning-To reduce the risk of injury, user must read instructions manual carefully.
	This symbol, placed before a safety comment, indicate kind of precaution, warning, or danger. Ignoring this w may lead to an accident. To reduce the risk of injury electrocution, please always follow the recommendation shown below.
	CORRECT DISPOSALThis product is subject to the provision of european [2012/19/EU. The symbol showing a wheelie bin crosse through indicates that the product requires separate re collection in the European Union. This applies to the and all accessories marked with this symbol. Products marked as such may not be discarded with normal d waste, but must be taken to acollection point for recy electrical and electronic devices.
	Warning- Be sure to wear eye protectors when using product.
	Warning- Be sure to wear ear protectors when using product.
	Warning- Be sure to wear dust masks when using th product.
	Warning- Disconnect mains plug from electrical outlet

SPECIFICATIONS

Model	BOSS200		BOSS200/1
Power	AC110—120V, 60 Hz, 450W S1	AC230V, 50 Hz, 450W S1	AC110—120V, 60 Hz, 450W S	AC230V, 50 Hz, 450W S1
No Load Speed	2400RPM ±5%	2000RPM ±5%	2400RPM ±5%	2000RPM ±5%
Oscillations	58 OPM
Spindle Size	1/2"
Sanding Sleeve Sizes	1/2", 3/4", 1", 1-1/2", 2", 3"
Maximum Workpiece Height	3-6/7"
Weight	37.5 Pounds (17Kg)		33 Pounds (15Kg)
Switch type

WARNING!

Read all safety warnings and all instructions. Failure to follow the warning and instructions may result in electric shock, fire and/or serious injury.

SAFETY GUIDELINES - DEFINITIONS

WORK AREA SAFETY

1. Keep work area clean and well lit. Cluttered or dark areas invite accide
2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks w may ignite the dust or fumes.
3. Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control.

ELECTRICAL SAFETY

1. Power tool plugs must match the outlet. Never modify the plug in ar Do not use any adapter plugs with earthed (grounded) power tools.
   Unmodified plugs and matching outlets will reduce risk of electric shock.
2. Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric sh if your body is earthed or grounded.
3. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
4. Do not abuse the cord. Never use the cord for carrying, pulling or tging the power tool. Keep cord away from heat, oil, sharp edges or mo parts. Damaged or entangled cords increase the risk of electric shock.
5. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of ele shock.
6. If operating a power tool in a damp location is unavoidable, use a g fault circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric shock.

PERSONAL SAFETY

1. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or the influence of drugs, alcohol or medication. A moment of inattention whi operating power tools may result in serious personal injury.
2. Use personal protective equipment. Always wear eye protection. Protect equipment such as a respiratory mask, non-skid safety shoes and hearing protection used for appropriate conditions will reduce the risk of personal injury
3. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
4. Remove any adjusting key or wrench before turning the power tool of wrench or a key left attached to a rotating part of the power tool may resu personal injury.
5. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
6. Dress properly. Do not wear loose clothing or jewelry. Keep your hair clothing away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.
7. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use c dust collection can reduce dust-related hazards.

POWER TOOL USE AND CARE

1. Do not force the power tool. Use the correct power tool for your aption. The correct power tool will do the job better and safer at the rate for was designed.
2. Do not use the power tool if the switch does not turn it on and of power tool that cannot be controlled with the switch is dangerous and must repaired.
3. Disconnect the plug from the power source and/or the battery pack for the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of sta

the power tool accidentally.

1. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
2. Maintain power tools. Check for misalignment or binding of moving pa breakage of parts and any other condition that may affect the power tool operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
3. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
4. Use the power tool, accessories and tool bits, etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
5. Use clamps to secure your workpiece to a stable surface. Holding a workpiece by hand or using your body to support it may lead to loss of co
6. KEEP GUARDS IN PLACE and in working order.

SERVICE

1. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power to maintained.

CALIFORNIA PROPOSITION 65 WARNING

Some dust created by power sanding, sawing, grinding, drilling, and other construction activities may contain chemicals, including lead, known to the State California to cause cancer, birth defects, or other reproductive harm. Wash has after handling. Some examples of these chemicals are:

• Lead from lead-based paints.
• Crystalline silica from bricks, cement, and other masonry products.
• Arsenic and chromium from chemically treated lumber.

Your risk from these exposures varies depending on how often you do this work. To reduce your exposure to these chemicals, work in a well-ventilated with approved safety equipment such as dust masks specially designed to filter

microscopic particles.

SPINDLE SANDER SAFETY

Do not operate the power tool until you have read and understood the following instructions and the warning labels.

1. TOOL PURPOSE. This sander is designed to sand wood or wood-like pro only. Sanding or grinding other materials could result in fire, injury, or damage the workpiece. Using the machine for any other purpose for which it is not designed may result in serious injuries, machine damage and voiding of the warranty.

2. MACHINE MOUNTING. For operation safety, the sander must be securely mounted onto a flat and stable surface or stand.

3. PERSONAL SAFETY

• Always wear ANSI Z87.1-approved glasses with side shields, hearing protect and a dust mask.

- Do not wear loose clothing or jewelry, as they might get drawn in by the back long hair.

• DO NOT wear gloves while operating this machine.

1. ELECTRIC CORDS. Keep cords away from heat, oil, sharp edges, and m parts of the tool. Have an electrician replace or repair damaged or worn cor immediately.

2. TOOL & ACCESSORIES INSPECTION. Before operation, check the tool and accessories for any damage or missing parts. Do not use the tool if any pa missing or damaged. Make sure all adjustments are correct and all connection are tight. Keep all guards in place.

6. SANDING ACCESSORIES

- Do not use sanding sleeves or drums that are damaged, torn, or loose. R worn or damaged sanding sleeves before operation.

• Always unplug the unit before making adjustments or changing sandpaper, rubber drums or throat plates.

• Always use the throat plate that matches the diameter of the drum to min the gap between the drum and the throat plate opening; this will reduce the

personal injury.

7. WORKPIECE REQUIREMENTS

• Only stand workpieces sturdy enough to withstand the force of the sanding spindle.
• Inspect the workpiece for imperfections, nails, staples, etc. before sanding.
  Never sand stock that has questionable imperfections or embedded foreign objects.
• When sanding a large workpiece, provide additional support. Do not sand with the workpiece unsupported.

• Sand only one workpiece at a time.

• PREVENTING ACCIDENTAL STARTING. Make sure the power switch is in OFF position prior to plugging in the machine. Always make sure the power is in the OFF position and the machine is unplugged when doing any cleani assembly, setup operations, or when not in use.

• Do not operate this tool until it is completely assembled and installed acc to the instructions.

• Remove scrap pieces and other objects from the table and sanding sleeve before turning ON the sander.

11. FEEDING THE WORKPIECE

• Allow spindle to reach full speed before feeding the workpiece. Do not turn machine while the sanding sleeve is contacting the workpiece.
• Be aware of the direction of the spindle's rotation (counterclockwise). Only the workpiece against the rotation of the spindle.

• Firmly hold the workpiece and lightly ease it against the spindle. Do not form a jam a workpiece into the sanding surface.

• Do not touch moving pieces. Keep hands away from the drum during operation.

If cleaning is necessary, use a brush to remove sawdust and chips instead of hands.

1. Never perform layout, assembly or set-up work on the table while the sa operating.

2. After turning off the sander, wait until the spindle comes to a complete before touching the workpiece.

3. Always turn off and unplug the machine before cleaning, making adjustme

or changing attachments. Accidental start-ups may occur if the tool is plugged during an accessory change or adjustment.

1. CLEANING. Never use solvents to clean plastic parts. Solvents could dissolve or otherwise damage the material. Use only a soft damp cloth to clean plastic parts.
2. REPLACEMENTS. Should any component of your sander be missing/damaged or fail in any way, shut off the switch and remove the plug from pow outlet. Replace the missing, damaged, or failed parts using only identical replacement parts before resuming operation.

These safety instructions can't possibly warn of every scenario that may arise with this tool, so always make sure to stay alert and use common sense during operation.

ELECTRICAL SAFETY

1. POLARIZED PLUGS. To reduce the risk of electric shock, this equipment polarized plug (one blade is wider than the other). This plug will fit in a po outlet only one way. If the plug does not fit fully in the outlet, reverse the still does not fit, contact a qualified electrician to install a proper outlet. Do modify the machine plug or the extension cord in any way.
2. GROUND FAULT CIRCUIT INTERRUPTER PROTECTION (GFCI) should be provided on the circuit or outlet used for this power tool to reduce the risk electric shock.
3. SERVICE AND REPAIR. To avoid danger, electrical appliances must only be repaired by qualified service technician using original replacement parts.

GUIDELINES AND RECOMMENDATIONS FOR EXTENSION CORDS

When using an extension cord, be sure to use one heavy enough to carry current your product will draw. An undersized cord will cause a drop in line resulting in loss of power and overheating. The table below shows the correct to be used according to cord length and ampere rating. When in doubt, use heavier cord. The smaller the gauge number, the heavier the cord.

AMPERAGE	REQUIRED GAUGE FOR EXTENSION CORDS
	25 ft.	50 ft.	100 ft.	150 ft.
4A	18 gauge	16 gauge	16 gauge	14 gauge

1. EXAMINE EXTENSION CORD BEFORE USE. Make sure your extension cc is properly wired and in good condition. Always replace a damaged extension or have it repaired by a qualified person before using it.
2. DO NOT ABUSE EXTENSION CORD. Do not pull on cord to disconnect receptacle; always disconnect by pulling on plug. Disconnect the extension cord from the receptacle before disconnecting the product from the extension cord. Protect your extension cords from sharp objects, excessive heat and damp/we areas.
3. USE A SEPARATE ELECTRICAL CIRCUIT FOR YOUR TOOL. This circuit must not be less than a 12-gauge wire and should be protected with a 15A time-delayed fuse.

Before connecting the motor to the power line, make sure the switch is in t position and the electric current is rated the same as the current stamped o motor nameplate. Running at a lower voltage will damage the motor.

PACKAGE CONTENTS

Before using the spindle sander, you must configure the machine by installing appropriate sanding drum, sanding sleeve, throat plate and spindle washer for your operation. Check your packing list against the diagram below. If any pad damaged or missing, please contact our customer service.

OPERATING INSTRUCTIONS

WARNING!

Do not plug in or turn on the tool until it is fully assembled according to the instructions.

Failure to follow the safety instructions may result in serious personal injury. Refer to the packing list diagram on page 8 to ensure that you are using t sizes of throat plates, drums and washers for each respective sanding sleeve ensure the workpiece can be properly supported and to minimize clearance, t the throat plate that matches the drum and sleeve that you'll be working with size of the throat plate is marked on the plate's surface.

NOTE: The smallest size sanding sleeve does not include a drum. It goes to onto the bare spindle.

INSTALLATION OF SPINDLE

1. Disconnect the machine from the power source
2. Insert Main Shaft I (2) into Main Shaft II (1)
3. Hold the Main Shaft II (1) in position using the wrench(3).
4. Screw the Main Shaft I (2) clockwise onto the Shaft II (1) using the spanner for the spindle (4).

Technical diagram of a mechanical device with numbered components for identification

INSTALLING THE ACCESSORIES

1. Slide the lower spindle washer (4) over the spindle shaft (2).
2. Install the preferred rubber drum (5) onto spindle shaft (2), followed by the corresponding sanding sleeve (6) and throat plate (3). Make the printed side of the throat plate is facing

NOTE: The 1/2" sleeve is installed directly on spindle.

1. Secure the sanding attachment in place w appropriate size sanding drum pressure plate and flat washer D8 (1).

Tighten the top hex nut M8 (8) with a wren the sanding drum is fully expanded and firmly the sanding sleeve. The sleeve cannot rotate freely without the sanding drum rotating.

Technical diagram of a mechanical assembly with numbered parts for identification

MACHINE MOUNTING

For safe operation, the machine must be secured onto a flat, secure worker stand.

The base of the machine has four 6 mm mounting holes. Place the sander mounting surface, and insert a pencil through the mounting holes to mark the locations. Remove the sander and drill out the mounting holes. Then align the

sander base over the mounting holes and secure the machine using four mo bolts, washers, locking washers and hex nuts (mounting hardware not included Securely tighten the hex nuts.

For temporary mounting, secure the sander to a mobile mounting board and large C-Clamps to secure the mounting board to a solid surface.

UPPER GUARD

WARNING!

Sanding operations are dusty and can produce particles that are harmful to y health. Always wear a dust mask and use an adequate dust collection syster

To connect a dust collection system to the machine:

1. Fit a 2.46-inch dust hose (not included) over the dust port and secure th

in place with a hose clamp if needed (not

1. Tug the hose to make sure the fitting is tight fit is necessary for proper performance.

2. Connect the other end of the dust hose dust collection system of your choice. A dust adapter may be needed (not included), dependence on the inlet size of your dust extractor. The port has an outer diameter of 2.46 inches, a inner diameter of 2.26 inches.

NOTE: Failure to use a dust collection syste void the warranty on this item. You must us collection system for the warranty to be valid

ON/OFF SWITCH WITH SAFETY KEY

The keyed ON/OFF switch (1) is intended to prevent unauthorized use of the sander.

1. To turn the sander ON, insert the safety the key slot in the center of the switch. Lift switch up to turn ON the sander.

2. To turn the sander OFF, push switch do

Remove the safety key when the sander has come to a complete stop by giving pulling it out.

WARNING: Remove the safety key whenever the sander is not in use. Place key in a safe place and out of the reach of children.

1. Make sure that the machine has been set mounted, and all accessories have been proposed installed according to the instructions on page section.
2. Plug in and turn ON the sander. Let the reach full speed.
3. Maintain a firm grip with both hands on the workpiece for maximum contr Slowly guide the workpiece against the rotation of the spindle.

NOTE: The spindle rotates in a counterclockwise direction. Guide the workpiece from the right to left. If you guide the workpiece in the opposite direction, the of the spinning sanding sleeve will tend to throw or bounce the workpiece at from the sanding sleeve, possibly resulting in injuries.

1. Maintain downward pressure on the workpiece against the table, gently wo it along the sanding sleeve until the desired curve has been created. Do not the workpiece against the sanding sleeve.
2. When you are finished, turn OFF the sander and wait for the spindle to a complete stop.
3. Remove the safety key and unplug the machine from the outlet. Follow the maintenance instructions on the next page to clean and maintain your sander

MAINTENANCE

WARNING!

To avoid accidents, turn OFF and unplug the tool from the electrical outlet by cleaning, adjusting, or performing any maintenance or lubrication work.

Illustration of hands operating a rotating mechanical device with a rotating knob (no text or symbols)

WARNING!

Any attempt to repair or replace electrical parts on this tool may be hazardo Servicing of the tool must be performed by a qualified technician. When serv use only identical replacement parts. Use of other parts may be hazardous o induce product failure.

ROUTINE INSPECTION

Before each use, inspect the general condition of the tool. If any of these for conditions exist, do not use until parts are replaced or the sharpener is properly repaired.

Check for:

• Loose hardware or improper mounting,
• Misalignment or binding of moving parts,
  • Damaged cord/electrical wiring,
• Cracked or broken parts, and
• Any other condition that may affect its safe operation

CLEANING & STORAGE

1. After every operation, use a vacuum to remove dust and chips from the surfaces, motor housing and work area. Keep the ventilation openings free from dust and debris to prevent the motor from overheating.
2. Wipe the tool surfaces clean with a soft cloth or brush. Make sure water not get into the tool.
3. Periodically, remove the throat plate and lower spindle washer and remove dust accumulation in the throat plate area.

CAUTION: Most plastics are susceptible to damage from various types of commercial solvents. Do not use any solvents or cleaning products that could damage the plastic parts.

Some of these include but are not limited to: gasoline, carbon tetrachloride, chlorinated cleaning solvents, and household detergents that contain ammonia.

1. Store the tool in a clean and dry place away from the reach of children. sanding accessories away from extremely hot/dry temperatures. Do not bend or fold the sanding sleeves.

LUBRICATION

All ball bearings are sealed and permanently lubricated. No further lubrication required.

PRODUCT DISPOSAL

Used power tools should not be disposed of together with household waste. product contains electronic components that should be recycled. Please take the product to your local recycling facility for responsible disposal and to minimize environmental impact.

TROUBLESHOOTING GUIDE

WARNING!

To avoid injury from an accidental start, turn the switch OFF and always remove the plug from the power source before making any adjustments.

PROBLEM	PROBLEM CAUSE	SUGGESTED CORRECTIVE ACTION
Sander does not turn on.	1、Power cord or extension cord damaged or not proper plugged in.2、Safety key is removed from power switch.3、Defective power switch, defective motor or wiring, sh circuit or loose connections.4、Circuit breaker is tripped.5、Worn carbon brushes.	1、Check the power cord, extension cord, power plug and the power outlet. Make sure tool is properly plugged in. Do use the if any cord is damaged.2、Insert the safety key into power switch.3、Stop using the tool and co customer service.Repairs must be done by a qualified technic.4、Push circuit breaker to reset.5、Replace carbon brushes.
Motor overheats.	1、Motor overloaded.2、Extension cord too long an insufficient gauge.3、Dust collection not being used.	1、Reduce load on motor - re pressureon the workpiece being sande2、Utilize an extension cord of appropriate gauge and length plug tool directly into outlet.3、Use dust collection.
Sanding grains easily rub off.	1、Sanding sleeve has been stored in an incorrect environment.2、Sanding sleeve has been damaged or folded	1、Store sanding accessories away from extremely hot/dry temperatures.2、Store sanding accessories flat—not bent or folded.
Deep sanding grooves or scars in workpiece.	1、Sanding sleeve grit is too coarse for the desired finish.2、Workpiece sanded across the grain.3、Too much sanding force.4、Workpiece held still again sanding surface for too long	1、Use a finer-grit sanding accessory.2、Sand with the grain of the wood.3、Reduce pressure on workpi while sanding.4、Keep workpiece moving wh sanding on the sanding sleeve

Manufacturer: Shanghaimuxinmuyeyouxiangongsi

Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN.

Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia

Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

UK

REP

YH CONSULTING LIMITED. C/O YH Consultin Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4A>

EC

REP

Affordable. Reliable. Home Improvement.

PONCEUSE À BROCHE

MODÈLE: BOSS200 ET BOSS200/1

VEVOR

Affordable. Reliable. Home Improvement.

SPINDLE SANDER

MODÈLE : BOSS200&BOSS200/1

Two orange industrial machines with black caps and mechanical components, shown from different angles (no text or symbols visible)

BOSS200 BOSS200/1

Technical diagram of a mechanical device with numbered components for identification

clé(3).

Exploded view diagram of a mechanical assembly with numbered parts for identification

Technical line drawing of a mechanical device with labeled components (no text or symbols present)

Technical line drawing of a mechanical assembly with cylindrical components and mounting base (no text or symbols)

Illustration of hands operating a rotating mechanical device with a rotating arrow and cylindrical component (no text or symbols)

WARNING!

TROUBLESHOOTING GUIDE

AVERTISSEMENT!

Lieu, Rancho Cucamonga, CA 91730

UK

REP

YH CONSULTING LIMITED. C/O YH Consultin Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4A>

EC

REP

Affordable. Reliable. Home Improvement.

SPINDELSCHLEIFER

MODELL: BOSS200 UND BOSS200/1

VEVOR

Affordable. Reliable. Home Improvement.

SPINDLE SANDER

MODELL: BOSS200&BOSS200/1

Two orange industrial machines with black caps and mechanical components, shown from different angles (no text or symbols visible)

BOSS200 BOSS200/1

Technical diagram of a mechanical device with numbered components for identification

Exploded view diagram of a mechanical assembly with numbered parts for identification

Technical line drawing of a mechanical device with labeled components (no text or symbols present)

Technical line drawing of a mechanical device with cylindrical components and mounting base (no text or symbols)

Illustration of hands operating a rotating mechanical device with a rotating knob (no text or symbols)

TROUBLESHOOTING GUIDE

WARNUNG!

YH CONSULTING LIMITED. C/O YH Consultin Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4A>

EC

REP

Affordable. Reliable. Home Improvement.

LEVIGATRICE A MANDRINO

MODELLO: BOSS200 E BOSS200/1

VEVOR

Affordable. Reliable. Home Improvement.

SPINDLE SANDER

MODELLO: BOSS200&BOSS200/1

Two orange industrial machines with black caps and mechanical components, shown from different angles (no text or symbols visible)

BOSS200 BOSS200/1

1. ACCESSORI PER LA LEVIGATURA

Technical diagram of a mechanical device with numbered components for identification

Technical diagram of a mechanical assembly with numbered parts for identification

Technical line drawing of a mechanical device with labeled components (no text or symbols present)

Technical line drawing of a mechanical device with cylindrical components and mounting base (no text or symbols)

INTERRUTTORE ON/OFF CON CHIAVE DI SICUREZZA

Illustration of hands operating a rotating mechanical component with a circular arrow indicating rotation (no text or symbols)

MANDRINO

TROUBLESHOOTING GUIDE

AVVERTIMENTO!

YH CONSULTING LIMITED. C/O YH Consultin Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4A>

EC

REP

Affordable. Reliable. Home Improvement.

LIJADORA DE HUSILLO

MODELO: BOSS200 Y BOSS200/1

VEVOR

Affordable. Reliable. Home Improvement.

SPINDLE SANDER

MODELO: BOSS200 Y BOSS200/1

Two orange industrial machines with black caps and mechanical components, shown from different angles (no text or symbols visible)

BOSS200 BOSS200/1

Technical diagram of a mechanical device with numbered components for identification

Technical diagram of a mechanical assembly with numbered parts for identification

Technical line drawing of a mechanical device with labeled components (no text or symbols present)

Technical line drawing of a mechanical device with cylindrical components and mounting base (no text or symbols)

Illustration of hands operating a rotating mechanical device with a rotating knob (no text or symbols)

TROUBLESHOOTING GUIDE

¡ADVERTENCIA!

YH CONSULTING LIMITED. C/O YH Consultin Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4A>

EC

REP

Affordable. Reliable. Home Improvement.

Affordable. Reliable. Home Improvement.

SPINDLE SANDER

MODELE: BOSS200&BOSS200/1

Two orange industrial machines with black caps and mechanical components, shown from different angles (no text or symbols visible)

BOSS200 BOSS200/1

BEZPIECZEŃSTWO W MIEJSCU PRACY

Technical diagram of a mechanical device with numbered parts, showing exploded and assembled views

skierowana do góry.

Technical line drawing of a mechanical device with labeled components (no text or symbols present)

Technical line drawing of a mechanical device with cylindrical components and mounting base (no text or symbols)

Illustration of hands operating a rotating mechanical component with a circular arrow indicating rotation (no text or symbols)

TROUBLESHOOTING GUIDE

OSTRZEŻENIE!

YH CONSULTING LIMITED. C/O YH Consultin Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4A>

EC

REP

Affordable. Reliable. Home Improvement.

SPINDELSCHUURMACHINE

MODEL: BOSS200&BOSS200/1

VEVOR

Affordable. Reliable. Home Improvement.

SPINDLE SANDER

MODEL: BOSS200&BOSS200/1

Two orange industrial machines with black caps and mechanical components, shown from different angles (no text or symbols visible)

BOSS200 BOSS200/1

WAARSCHUWING VOOR CALIFORNIË PROPOSITIE 65

Technical diagram of a mechanical device with numbered components for identification

van de

moersleutel(3).

Technical diagram of a mechanical assembly with numbered parts for identification

BOVENSTE BESCHERMING

WARNING!

Technical line drawing of a mechanical device with labeled components (no text or symbols present)

Technical line drawing of a mechanical device with cylindrical components and mounting base (no text or symbols)

Illustration of hands operating a rotating mechanical device with a rotating knob (no text or symbols)

WARNING!

TROUBLESHOOTING GUIDE

WAARSCHUWING!

YH CONSULTING LIMITED. C/O YH Consultin Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4A>

EC

REP

Affordable. Reliable. Home Improvement.

SPINDELSLIPMASKIN

MODELL: BOSS200 & BOSS200/1

VEVOR

Affordable. Reliable. Home Improvement.

SPINDLE SANDER

MODELL: BOSS200&BOSS200/1

Two orange industrial machines with black caps and mechanical components, shown from different angles (no text or symbols visible)

BOSS200 BOSS200/1

Technical diagram of a mechanical device with numbered components for identification

MONTERING AV TILLBEHÖR

Technical diagram of a mechanical assembly with numbered parts for identification

Technical line drawing of a mechanical device with labeled components (no text or symbols present)

Technical line drawing of a mechanical device with cylindrical components and mounting base (no text or symbols)

Illustration of hands operating a rotating mechanical device with a rotating wheel (no text or symbols)

TROUBLESHOOTING GUIDE

WARNING!

YH CONSULTING LIMITED. C/O YH Consultin

Limited Office 147, Centurion House, London

Road, Staines-upon-Thames, Surrey, TW18 4A>

EC

REP

E-CrossStu GmbH

Mainzer Landstr.69,

60329 Frankfurt am Main.