Bali 3200 X-Slide - Iron TAURUS - Free user manual and instructions

USER MANUAL Bali 3200 X-Slide TAURUS

Line drawing of a steam iron with internal components and a vertical ruler (no text or symbols)

EN. Instructions for use

FR. Mode d'emploi

B A D C F E G H I J

ES

English (Original instructions)

STEAM IRON

BALI 3200 X-SLIDE

DESCRIPTION

A Spray button
B Steam blast button
C Steam flow regulator
D Pilot light
E Spray nozzle
F Water inlet lid
G Temperature regulator
H Self-clean button

I Soleplate

J Filling cup

If the model of your appliance does not have the accessories described above, they can also be bought separately from the Technical Assistance Service.

USE AND CARE

• Fully extend the appliance's supply cord before each use.
• Do not use the appliance if the parts or accessories are not properly fitted.
• Do not use the appliance if the accessories attached to it are defective. Replace them immediately.
• Do not switch the appliance on without water.
• Use the appliance handle/s, to catch it or move it.
• Do not use the appliance if it is tipped up and do not turn it over.
• Do not turn the appliance over while it is in use or connected to the mains.
• Respect the MAX level indicator.
• Disconnect the appliance from the mains when not in use and before undertaking any cleaning task.
• Do not store or transport the appliance if it is still hot.
• For a correct operation, keep the soleplate in proper conditions; do not operate over metal objects (ironing board metal parts, buttons, zips etc.)
• It is advisable to use distilled water, especially if the water in your area contains clay or if it is “hard” (containing lime or magnesium).
• Check that the lid is closed properly before starting the appliance.
• Never leave the appliance connected and unattended if is not in use. This saves energy and prolongs the life of the appliance.

• Never rest the appliance into a surface while in use.

• Do not use the appliance with pets or animals.

• Turning the temperature regulator to the OFF setting does not mean that the appliance is switched off.

INSTRUCTIONS FOR USE

BEFORE USE

• Make sure that all product's packaging has been removed.
• Please read carefully the "Safety advice and warnings" booklet before first use
• Some parts of the appliance have been lightly greased. Consequently, the first time the appliance is used a light smoke may be detected. After a short time, this smoke will disappear.
• Prepare the appliance according to the function you wish to use.

FILLING WITH WATER

• It is essential to have filled the water tank with water to be able to work with steam.
• Open water inlet lid.
• Fill the water tank taking care to observe the MAX level.
• Pour in water using the filling cup.
• Close water inlet lid.

USE

• Extend the supply cord completely before plugging it in.
• Connect the appliance to the mains.
• Turn the temperature regulator to the desired temperature position.
  • The pilot light comes on.
• Select the desired steam flow by using the steam flow regulator.
• Do not use temperatures higher than those indicated on the garments to be treated.

• Temperature for synthetic fibres (Polyester, Nylon...).
●● Temperature for silk and wool.
●●● Temperature for cotton and linen.
- If garment has various kinds of fibres, select the temperature for the fibre that requires the lowest temperature. (For example, select the temperature for polyester for an article made out of 60% polyester and 40% cotton).
- Wait until the pilot light has gone out which will indicate that the appliance has reached an adequate temperature.

DRY IRONING

- The appliance has a steam flow regulator that permits dry ironing (without steam) when placed in the minimum position.

STEAM IRONING

- It is possible to iron with steam whenever the water tank is filled with water and the adequate temperature is selected.

STEAM FLOW CONTROL

- The appliance has a steam flow regulator that allows getting the control of the steam flow.

SPRAY

• The spray can be used in both steam and dry ironing.

- Press the spray button to use this operation.

STEAM BLAST

- This function provides extra steam for eliminating wrinkles.

- Press the steam blast button. Wait a few seconds until vapour penetrates the fibres of the garment before pushing the button again. For optimum steam quality, do not apply more than three successive blasts.

VERTICAL STEAMING

- It is possible to iron hanging curtains, items of clothing on his hanger, etc. To do so, follow the instructions:

- Select the maximum temperature of the iron.

- Move the iron in a top to bottom direction while pressing the steam blast button. Important: for cotton and linen, it's recommended to put the iron base in contact with the material. For other more delicate fibres, it's recommended to keep the iron base at some centimetres of distance.

ONCE YOU HAVE FINISHED USING THE APPLIANCE

- Select the OFF position using the temperature regulator.

- Unplug the appliance from the mains.

- Allow to cool down.

- Remove the water from the inside of the appliance.

- Clean the appliance.

PRACTICAL RECOMMENDATIONS

- Classify the garments into groups by ironing temperature. The appliance heats up more quickly than it cools down, therefore, to avoid accidents, minimise energy consumption and optimise time, it is advisable to start off ironing items that require lower temperatures and progress to those that need higher temperatures.

- Pure wool fabrics (100%) can be ironed with the iron set to steam. Select a high steam temperature and place a cotton cloth between the iron's metal surface and the garment.

SAFETY THERMAL PROTECTOR

- The appliance has a safety device, which protects the appliance from overheating.

CLEANING

- Disconnect the appliance from the mains and allow it to cool before undertaking any cleaning task.

- Clean the equipment with a damp cloth with a few drops of washing-up liquid and then dry.

- Do not use solvents, or products with an acid or base pH such as bleach, or abrasive products, for cleaning the appliance.

- Never immerse the appliance in water or any other liquid or place it under running water.

SELF-CLEANING FUNCTION

- It is important to self-clean the appliance at least once every two weeks to remove calcium and any other built-up minerals inside the iron.

- Fill the water tank to its maximum level, as indicated on "Filling with water" section.

- Place the iron in the vertical position, plug into the mains and select the maximum temperature.

- Leave the appliance to heat up until the pilot light indicates that it has reached its consigned temperature.

- Unplug the appliance and place in the sink.

- Press the self-clean button, and keep it pressed down for 1 minute.

- Let the water flow out through the steam vents in the base, while lightly shaking the appliance.

- Release the button after a minute or when the tank becomes empty.

- Leave the iron in the vertical position until it has cooled.

HOW TO DEAL WITH LIME SCALE INCRUSTATIONS

- For the appliance to work correctly it should be kept free of limescale or magnesium incrustations caused by the use of hard water.

- To avoid this kind of problem it is advisable to use distilled water.

• However, if it is not possible to use the kind of water recommended above, you should periodically remove the limescale from the appliance:

- Every 6 weeks if the water is "very hard".

- Every 12 weeks if the water is "hard".

• To do so, we recommend the use of the specific product for this kind of appliance, which can be found in specialised shops and authorised technical services.
- A specific anti-lime scale product should be used on this kind of product.
- Homemade solutions are not recommended in the decaling of this appliance, such as the use of vinegar.

FR

RECOMMANDATIONS PRATIQUES

C Regulator for dampstrøm

D Kontrollampe

E Sprøytedyse

F Lokk for vanninntak

G Temperaturregulator

H Knappen for selvrensing

I Såleplate

J Påfyllingsbeger

,הכלההוּרָה,הִיַבְרָה,הִיַבְרָה,הִיַבְרָה,הִיַבְרָה,הִיַבְרָה,הִיַבְרָה,הִיַבְרָה,הִיַבְר'

הכלה pH is men in his party, and the party will be